Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

107 files changed, 5964 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/media/atmel-isc.txt b/Documentation/devicetree/bindings/media/atmel-isc.txt
new file mode 100644
index 000000000..bbe0e87c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/atmel-isc.txt
@@ -0,0 +1,65 @@
+Atmel Image Sensor Controller (ISC)
+----------------------------------------------
+
+Required properties for ISC:
+- compatible
+	Must be "atmel,sama5d2-isc".
+- reg
+	Physical base address and length of the registers set for the device.
+- interrupts
+	Should contain IRQ line for the ISC.
+- clocks
+	List of clock specifiers, corresponding to entries in
+	the clock-names property;
+	Please refer to clock-bindings.txt.
+- clock-names
+	Required elements: "hclock", "iscck", "gck".
+- #clock-cells
+	Should be 0.
+- clock-output-names
+	Should be "isc-mck".
+- pinctrl-names, pinctrl-0
+	Please refer to pinctrl-bindings.txt.
+
+ISC supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+isc: isc@f0008000 {
+	compatible = "atmel,sama5d2-isc";
+	reg = <0xf0008000 0x4000>;
+	interrupts = <46 IRQ_TYPE_LEVEL_HIGH 5>;
+	clocks = <&isc_clk>, <&iscck>, <&isc_gclk>;
+	clock-names = "hclock", "iscck", "gck";
+	#clock-cells = <0>;
+	clock-output-names = "isc-mck";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
+
+	port {
+		isc_0: endpoint {
+			remote-endpoint = <&ov7740_0>;
+			hsync-active = <1>;
+			vsync-active = <0>;
+			pclk-sample = <1>;
+		};
+	};
+};
+
+i2c1: i2c@fc028000 {
+	ov7740: camera@21 {
+		compatible = "ovti,ov7740";
+		reg = <0x21>;
+		clocks = <&isc>;
+		clock-names = "xvclk";
+		assigned-clocks = <&isc>;
+		assigned-clock-rates = <24000000>;
+
+		port {
+			ov7740_0: endpoint {
+				remote-endpoint = <&isc_0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/atmel-isi.txt b/Documentation/devicetree/bindings/media/atmel-isi.txt
new file mode 100644
index 000000000..332513a15
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/atmel-isi.txt
@@ -0,0 +1,66 @@
+Atmel Image Sensor Interface (ISI)
+----------------------------------
+
+Required properties for ISI:
+- compatible: must be "atmel,at91sam9g45-isi".
+- reg: physical base address and length of the registers set for the device.
+- interrupts: should contain IRQ line for the ISI.
+- clocks: list of clock specifiers, corresponding to entries in the clock-names
+	property; please refer to clock-bindings.txt.
+- clock-names: required elements: "isi_clk".
+- pinctrl-names, pinctrl-0: please refer to pinctrl-bindings.txt.
+
+ISI supports a single port node with parallel bus. It shall contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node properties
+------------------------
+
+- bus-width: <8> or <10> (mandatory)
+- hsync-active (default: active high)
+- vsync-active (default: active high)
+- pclk-sample (default: sample on falling edge)
+- remote-endpoint: A phandle to the bus receiver's endpoint node (mandatory).
+
+Example:
+
+isi: isi@f0034000 {
+	compatible = "atmel,at91sam9g45-isi";
+	reg = <0xf0034000 0x4000>;
+	interrupts = <37 IRQ_TYPE_LEVEL_HIGH 5>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_isi_data_0_7>;
+	clocks = <&isi_clk>;
+	clock-names = "isi_clk";
+	port {
+		isi_0: endpoint {
+			remote-endpoint = <&ov2640_0>;
+			bus-width = <8>;
+			vsync-active = <1>;
+			hsync-active = <1>;
+		};
+	};
+};
+
+i2c1: i2c@f0018000 {
+	ov2640: camera@30 {
+		compatible = "ovti,ov2640";
+		reg = <0x30>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+		resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
+		pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+		clocks = <&pck0>;
+		clock-names = "xvclk";
+		assigned-clocks = <&pck0>;
+		assigned-clock-rates = <25000000>;
+
+		port {
+			ov2640_0: endpoint {
+				remote-endpoint = <&isi_0>;
+				bus-width = <8>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/cdns,csi2rx.txt b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt
new file mode 100644
index 000000000..6b02a0657
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/cdns,csi2rx.txt
@@ -0,0 +1,100 @@
+Cadence MIPI-CSI2 RX controller
+===============================
+
+The Cadence MIPI-CSI2 RX controller is a CSI-2 bridge supporting up to 4 CSI
+lanes in input, and 4 different pixel streams in output.
+
+Required properties:
+  - compatible: must be set to "cdns,csi2rx" and an SoC-specific compatible
+  - reg: base address and size of the memory mapped region
+  - clocks: phandles to the clocks driving the controller
+  - clock-names: must contain:
+    * sys_clk: main clock
+    * p_clk: register bank clock
+    * pixel_if[0-3]_clk: pixel stream output clock, one for each stream
+                         implemented in hardware, between 0 and 3
+
+Optional properties:
+  - phys: phandle to the external D-PHY, phy-names must be provided
+  - phy-names: must contain "dphy", if the implementation uses an
+               external D-PHY
+
+Required subnodes:
+  - ports: A ports node with one port child node per device input and output
+           port, in accordance with the video interface bindings defined in
+           Documentation/devicetree/bindings/media/video-interfaces.txt. The
+           port nodes are numbered as follows:
+
+           Port Description
+           -----------------------------
+           0    CSI-2 input
+           1    Stream 0 output
+           2    Stream 1 output
+           3    Stream 2 output
+           4    Stream 3 output
+
+           The stream output port nodes are optional if they are not
+           connected to anything at the hardware level or implemented
+           in the design.Since there is only one endpoint per port,
+           the endpoints are not numbered.
+
+
+Example:
+
+csi2rx: csi-bridge@0d060000 {
+	compatible = "cdns,csi2rx";
+	reg = <0x0d060000 0x1000>;
+	clocks = <&byteclock>, <&byteclock>
+		 <&coreclock>, <&coreclock>,
+		 <&coreclock>, <&coreclock>;
+	clock-names = "sys_clk", "p_clk",
+		      "pixel_if0_clk", "pixel_if1_clk",
+		      "pixel_if2_clk", "pixel_if3_clk";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			csi2rx_in_sensor: endpoint {
+				remote-endpoint = <&sensor_out_csi2rx>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			csi2rx_out_grabber0: endpoint {
+				remote-endpoint = <&grabber0_in_csi2rx>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			csi2rx_out_grabber1: endpoint {
+				remote-endpoint = <&grabber1_in_csi2rx>;
+			};
+		};
+
+		port@3 {
+			reg = <3>;
+
+			csi2rx_out_grabber2: endpoint {
+				remote-endpoint = <&grabber2_in_csi2rx>;
+			};
+		};
+
+		port@4 {
+			reg = <4>;
+
+			csi2rx_out_grabber3: endpoint {
+				remote-endpoint = <&grabber3_in_csi2rx>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/cdns,csi2tx.txt b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt
new file mode 100644
index 000000000..459c6e332
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/cdns,csi2tx.txt
@@ -0,0 +1,98 @@
+Cadence MIPI-CSI2 TX controller
+===============================
+
+The Cadence MIPI-CSI2 TX controller is a CSI-2 bridge supporting up to
+4 CSI lanes in output, and up to 4 different pixel streams in input.
+
+Required properties:
+  - compatible: must be set to "cdns,csi2tx"
+  - reg: base address and size of the memory mapped region
+  - clocks: phandles to the clocks driving the controller
+  - clock-names: must contain:
+    * esc_clk: escape mode clock
+    * p_clk: register bank clock
+    * pixel_if[0-3]_clk: pixel stream output clock, one for each stream
+                         implemented in hardware, between 0 and 3
+
+Optional properties
+  - phys: phandle to the D-PHY. If it is set, phy-names need to be set
+  - phy-names: must contain "dphy"
+
+Required subnodes:
+  - ports: A ports node with one port child node per device input and output
+           port, in accordance with the video interface bindings defined in
+           Documentation/devicetree/bindings/media/video-interfaces.txt. The
+           port nodes are numbered as follows.
+
+           Port Description
+           -----------------------------
+           0    CSI-2 output
+           1    Stream 0 input
+           2    Stream 1 input
+           3    Stream 2 input
+           4    Stream 3 input
+
+           The stream input port nodes are optional if they are not
+           connected to anything at the hardware level or implemented
+           in the design. Since there is only one endpoint per port,
+           the endpoints are not numbered.
+
+Example:
+
+csi2tx: csi-bridge@0d0e1000 {
+	compatible = "cdns,csi2tx";
+	reg = <0x0d0e1000 0x1000>;
+	clocks = <&byteclock>, <&byteclock>,
+		 <&coreclock>, <&coreclock>,
+		 <&coreclock>, <&coreclock>;
+	clock-names = "p_clk", "esc_clk",
+		      "pixel_if0_clk", "pixel_if1_clk",
+		      "pixel_if2_clk", "pixel_if3_clk";
+
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			csi2tx_out: endpoint {
+				remote-endpoint = <&remote_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			csi2tx_in_stream0: endpoint {
+				remote-endpoint = <&stream0_out>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			csi2tx_in_stream1: endpoint {
+				remote-endpoint = <&stream1_out>;
+			};
+		};
+
+		port@3 {
+			reg = <3>;
+
+			csi2tx_in_stream2: endpoint {
+				remote-endpoint = <&stream2_out>;
+			};
+		};
+
+		port@4 {
+			reg = <4>;
+
+			csi2tx_in_stream3: endpoint {
+				remote-endpoint = <&stream3_out>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/cec-gpio.txt b/Documentation/devicetree/bindings/media/cec-gpio.txt
new file mode 100644
index 000000000..47e8d73d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/cec-gpio.txt
@@ -0,0 +1,42 @@
+* HDMI CEC GPIO driver
+
+The HDMI CEC GPIO module supports CEC implementations where the CEC line
+is hooked up to a pull-up GPIO line and - optionally - the HPD line is
+hooked up to another GPIO line.
+
+Please note: the maximum voltage for the CEC line is 3.63V, for the HPD and
+5V lines it is 5.3V. So you may need some sort of level conversion circuitry
+when connecting them to a GPIO line.
+
+Required properties:
+  - compatible: value must be "cec-gpio".
+  - cec-gpios: gpio that the CEC line is connected to. The line should be
+    tagged as open drain.
+
+If the CEC line is associated with an HDMI receiver/transmitter, then the
+following property is also required:
+
+  - hdmi-phandle - phandle to the HDMI controller, see also cec.txt.
+
+If the CEC line is not associated with an HDMI receiver/transmitter, then
+the following property is optional and can be used for debugging HPD changes:
+
+  - hpd-gpios: gpio that the HPD line is connected to.
+
+This property is optional and can be used for debugging changes on the 5V line:
+
+  - v5-gpios: gpio that the 5V line is connected to.
+
+Example for the Raspberry Pi 3 where the CEC line is connected to
+pin 26 aka BCM7 aka CE1 on the GPIO pin header, the HPD line is
+connected to pin 11 aka BCM17 and the 5V line is connected to pin
+15 aka BCM22 (some level shifter is needed for the HPD and 5V lines!):
+
+#include <dt-bindings/gpio/gpio.h>
+
+cec-gpio {
+	compatible = "cec-gpio";
+	cec-gpios = <&gpio 7 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+	hpd-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
+	v5-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
+};
diff --git a/Documentation/devicetree/bindings/media/cec.txt b/Documentation/devicetree/bindings/media/cec.txt
new file mode 100644
index 000000000..22d7aae3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/cec.txt
@@ -0,0 +1,8 @@
+Common bindings for HDMI CEC adapters
+
+- hdmi-phandle: phandle to the HDMI controller.
+
+- needs-hpd: if present the CEC support is only available when the HPD
+  is high. Some boards only let the CEC pin through if the HPD is high,
+  for example if there is a level converter that uses the HPD to power
+  up or down.
diff --git a/Documentation/devicetree/bindings/media/coda.txt b/Documentation/devicetree/bindings/media/coda.txt
new file mode 100644
index 000000000..90eb74cc1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/coda.txt
@@ -0,0 +1,31 @@
+Chips&Media Coda multi-standard codec IP
+========================================
+
+Coda codec IPs are present in i.MX SoCs in various versions,
+called VPU (Video Processing Unit).
+
+Required properties:
+- compatible : should be "fsl,<chip>-src" for i.MX SoCs:
+  (a) "fsl,imx27-vpu" for CodaDx6 present in i.MX27
+  (b) "fsl,imx51-vpu" for CodaHx4 present in i.MX51
+  (c) "fsl,imx53-vpu" for CODA7541 present in i.MX53
+  (d) "fsl,imx6q-vpu" for CODA960 present in i.MX6q
+- reg: should be register base and length as documented in the
+  SoC reference manual
+- interrupts : Should contain the VPU interrupt. For CODA960,
+  a second interrupt is needed for the MJPEG unit.
+- clocks : Should contain the ahb and per clocks, in the order
+  determined by the clock-names property.
+- clock-names : Should be "ahb", "per"
+- iram : phandle pointing to the SRAM device node
+
+Example:
+
+vpu: vpu@63ff4000 {
+	compatible = "fsl,imx53-vpu";
+	reg = <0x63ff4000 0x1000>;
+	interrupts = <9>;
+	clocks = <&clks 63>, <&clks 63>;
+	clock-names = "ahb", "per";
+	iram = <&ocram>;
+};
diff --git a/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt
new file mode 100644
index 000000000..0bf6fb7fb
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/exynos-fimc-lite.txt
@@ -0,0 +1,16 @@
+Exynos4x12/Exynos5 SoC series camera host interface (FIMC-LITE)
+
+Required properties:
+
+- compatible	: should be one of:
+		  "samsung,exynos4212-fimc-lite" for Exynos4212/4412 SoCs,
+		  "samsung,exynos5250-fimc-lite" for Exynos5250 compatible
+		   devices;
+- reg		: physical base address and size of the device memory mapped
+		  registers;
+- interrupts	: should contain FIMC-LITE interrupt;
+- clocks	: FIMC LITE gate clock should be specified in this property.
+- clock-names	: should contain "flite" entry.
+
+Each FIMC device should have an alias in the aliases node, in the form of
+fimc-lite<n>, where <n> is an integer specifying the IP block instance.
diff --git a/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt
new file mode 100644
index 000000000..38941db23
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/exynos-jpeg-codec.txt
@@ -0,0 +1,16 @@
+Samsung S5P/EXYNOS SoC series JPEG codec
+
+Required properties:
+
+- compatible	: should be one of:
+		  "samsung,s5pv210-jpeg", "samsung,exynos4210-jpeg",
+		  "samsung,exynos3250-jpeg", "samsung,exynos5420-jpeg",
+		  "samsung,exynos5433-jpeg";
+- reg		: address and length of the JPEG codec IP register set;
+- interrupts	: specifies the JPEG codec IP interrupt;
+- clock-names   : should contain:
+		   - "jpeg" for the core gate clock,
+		   - "sclk" for the special clock (optional).
+- clocks	: should contain the clock specifier and clock ID list
+		  matching entries in the clock-names property; from
+		  the common clock bindings.
diff --git a/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt
new file mode 100644
index 000000000..32ced99d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/exynos4-fimc-is.txt
@@ -0,0 +1,50 @@
+Exynos4x12 SoC series Imaging Subsystem (FIMC-IS)
+
+The FIMC-IS is a subsystem for processing image signal from an image sensor.
+The Exynos4x12 SoC series FIMC-IS V1.5 comprises of a dedicated ARM Cortex-A5
+processor, ISP, DRC and FD IP blocks and peripheral devices such as UART, I2C
+and SPI bus controllers, PWM and ADC.
+
+fimc-is node
+------------
+
+Required properties:
+- compatible	: should be "samsung,exynos4212-fimc-is" for Exynos4212 and
+		  Exynos4412 SoCs;
+- reg		: physical base address and length of the registers set;
+- interrupts	: must contain two FIMC-IS interrupts, in order: ISP0, ISP1;
+- clocks	: list of clock specifiers, corresponding to entries in
+		  clock-names property;
+- clock-names	: must contain "ppmuispx", "ppmuispx", "lite0", "lite1"
+		  "mpll", "sysreg", "isp", "drc", "fd", "mcuisp", "gicisp",
+		  "pwm_isp", "mcuctl_isp", "uart", "ispdiv0", "ispdiv1",
+		  "mcuispdiv0", "mcuispdiv1", "aclk200", "div_aclk200",
+		  "aclk400mcuisp", "div_aclk400mcuisp" entries,
+		  matching entries in the clocks property.
+pmu subnode
+-----------
+
+Required properties:
+ - reg : must contain PMU physical base address and size of the register set.
+
+The following are the FIMC-IS peripheral device nodes and can be specified
+either standalone or as the fimc-is node child nodes.
+
+i2c-isp (ISP I2C bus controller) nodes
+------------------------------------------
+
+Required properties:
+
+- compatible	: should be "samsung,exynos4212-i2c-isp" for Exynos4212 and
+		  Exynos4412 SoCs;
+- reg		: physical base address and length of the registers set;
+- clocks	: must contain gate clock specifier for this controller;
+- clock-names	: must contain "i2c_isp" entry.
+
+For the above nodes it is required to specify a pinctrl state named "default",
+according to the pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt.
+
+Device tree nodes of the image sensors' controlled directly by the FIMC-IS
+firmware must be child nodes of their corresponding ISP I2C bus controller node.
+The data link of these image sensors must be specified using the common video
+interfaces bindings, defined in video-interfaces.txt.
diff --git a/Documentation/devicetree/bindings/media/exynos5-gsc.txt b/Documentation/devicetree/bindings/media/exynos5-gsc.txt
new file mode 100644
index 000000000..bc963a6d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/exynos5-gsc.txt
@@ -0,0 +1,38 @@
+* Samsung Exynos5 G-Scaler device
+
+G-Scaler is used for scaling and color space conversion on EXYNOS5 SoCs.
+
+Required properties:
+- compatible: should be one of
+	      "samsung,exynos5250-gsc"
+	      "samsung,exynos5420-gsc"
+	      "samsung,exynos5433-gsc"
+	      "samsung,exynos5-gsc" (deprecated)
+- reg: should contain G-Scaler physical address location and length.
+- interrupts: should contain G-Scaler interrupt number
+
+Optional properties:
+- samsung,sysreg: handle to syscon used to control the system registers to
+  set writeback input and destination
+
+Example:
+
+gsc_0:  gsc@13e00000 {
+	compatible = "samsung,exynos5250-gsc";
+	reg = <0x13e00000 0x1000>;
+	interrupts = <0 85 0>;
+};
+
+Aliases:
+Each G-Scaler node should have a numbered alias in the aliases node,
+in the form of gscN, N = 0...3. G-Scaler driver uses these aliases
+to retrieve the device IDs using "of_alias_get_id()" call.
+
+Example:
+
+aliases {
+	gsc0 =&gsc_0;
+	gsc1 =&gsc_1;
+	gsc2 =&gsc_2;
+	gsc3 =&gsc_3;
+};
diff --git a/Documentation/devicetree/bindings/media/fsl-vdoa.txt b/Documentation/devicetree/bindings/media/fsl-vdoa.txt
new file mode 100644
index 000000000..6c5628530
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/fsl-vdoa.txt
@@ -0,0 +1,21 @@
+Freescale Video Data Order Adapter
+==================================
+
+The Video Data Order Adapter (VDOA) is present on the i.MX6q. Its sole purpose
+is to reorder video data from the macroblock tiled order produced by the CODA
+960 VPU to the conventional raster-scan order for scanout.
+
+Required properties:
+- compatible: must be "fsl,imx6q-vdoa"
+- reg: the register base and size for the device registers
+- interrupts: the VDOA interrupt
+- clocks: the vdoa clock
+
+Example:
+
+vdoa@21e4000 {
+        compatible = "fsl,imx6q-vdoa";
+        reg = <0x021e4000 0x4000>;
+        interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&clks IMX6QDL_CLK_VDOA>;
+};
diff --git a/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt
new file mode 100644
index 000000000..58261fb7b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/gpio-ir-receiver.txt
@@ -0,0 +1,17 @@
+Device-Tree bindings for GPIO IR receiver
+
+Required properties:
+	- compatible: should be "gpio-ir-receiver".
+	- gpios: specifies GPIO used for IR signal reception.
+
+Optional properties:
+	- linux,rc-map-name: see rc.txt file in the same
+	  directory.
+
+Example node:
+
+	ir: ir-receiver {
+		compatible = "gpio-ir-receiver";
+		gpios = <&gpio0 19 1>;
+		linux,rc-map-name = "rc-rc6-mce";
+	};
diff --git a/Documentation/devicetree/bindings/media/hix5hd2-ir.txt b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt
new file mode 100644
index 000000000..13ebc0fac
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/hix5hd2-ir.txt
@@ -0,0 +1,25 @@
+Device-Tree bindings for hix5hd2 ir IP
+
+Required properties:
+	- compatible: Should contain "hisilicon,hix5hd2-ir".
+	- reg: Base physical address of the controller and length of memory
+	  mapped region.
+	- interrupts: interrupt-specifier for the sole interrupt generated by
+	  the device. The interrupt specifier format depends on the interrupt
+	  controller parent.
+	- clocks: clock phandle and specifier pair.
+
+Optional properties:
+	- linux,rc-map-name: see rc.txt file in the same directory.
+	- hisilicon,power-syscon: DEPRECATED. Don't use this in new dts files.
+		Provide correct clocks instead.
+
+Example node:
+
+	ir: ir@f8001000 {
+		compatible = "hisilicon,hix5hd2-ir";
+		reg = <0xf8001000 0x1000>;
+		interrupts = <0 47 4>;
+		clocks = <&clock HIX5HD2_IR_CLOCK>;
+		linux,rc-map-name = "rc-tivo";
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ad5820.txt b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
new file mode 100644
index 000000000..5940ca11c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ad5820.txt
@@ -0,0 +1,19 @@
+* Analog Devices AD5820 autofocus coil
+
+Required Properties:
+
+  - compatible: Must contain "adi,ad5820"
+
+  - reg: I2C slave address
+
+  - VANA-supply: supply of voltage for VANA pin
+
+Example:
+
+       ad5820: coil@c {
+               compatible = "adi,ad5820";
+               reg = <0x0c>;
+
+               VANA-supply = <&vaux4>;
+       };
+
diff --git a/Documentation/devicetree/bindings/media/i2c/adp1653.txt b/Documentation/devicetree/bindings/media/i2c/adp1653.txt
new file mode 100644
index 000000000..4cce0de40
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adp1653.txt
@@ -0,0 +1,38 @@
+* Analog Devices ADP1653 flash LED driver
+
+Required Properties:
+
+  - compatible: Must contain "adi,adp1653"
+
+  - reg: I2C slave address
+
+  - enable-gpios: Specifier of the GPIO connected to EN pin
+
+There are two LED outputs available - flash and indicator. One LED is
+represented by one child node, nodes need to be named "flash" and "indicator".
+
+Required properties of the LED child node:
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+
+Required properties of the flash LED child node:
+
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+- flash-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+	adp1653: led-controller@30 {
+		compatible = "adi,adp1653";
+		reg = <0x30>;
+		enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
+
+		flash {
+			flash-timeout-us = <500000>;
+			flash-max-microamp = <320000>;
+			led-max-microamp = <50000>;
+		};
+		indicator {
+			led-max-microamp = <17500>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7180.txt b/Documentation/devicetree/bindings/media/i2c/adv7180.txt
new file mode 100644
index 000000000..552b6a82c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7180.txt
@@ -0,0 +1,49 @@
+* Analog Devices ADV7180 analog video decoder family
+
+The adv7180 family devices are used to capture analog video to different
+digital interfaces like MIPI CSI-2 or parallel video.
+
+Required Properties :
+- compatible : value must be one of
+		"adi,adv7180"
+		"adi,adv7180cp"
+		"adi,adv7180st"
+		"adi,adv7182"
+		"adi,adv7280"
+		"adi,adv7280-m"
+		"adi,adv7281"
+		"adi,adv7281-m"
+		"adi,adv7281-ma"
+		"adi,adv7282"
+		"adi,adv7282-m"
+
+Device nodes of "adi,adv7180cp" and "adi,adv7180st" must contain one
+'port' child node per device input and output port, in accordance with the
+video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+nodes are numbered as follows.
+
+  Port		adv7180cp	adv7180st
+-------------------------------------------------------------------
+  Input		0-2		0-5
+  Output	3		6
+
+The digital output port node must contain at least one endpoint.
+
+Optional Properties :
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+  if any.
+
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		adv7180@21 {
+			compatible = "adi,adv7180";
+			reg = <0x21>;
+		};
+		...
+	};
+
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7343.txt b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
new file mode 100644
index 000000000..5653bc242
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7343.txt
@@ -0,0 +1,48 @@
+* Analog Devices adv7343 video encoder
+
+The ADV7343 are high speed, digital-to-analog video encoders in a 64-lead LQFP
+package. Six high speed, 3.3 V, 11-bit video DACs provide support for composite
+(CVBS), S-Video (Y-C), and component (YPrPb/RGB) analog outputs in standard
+definition (SD), enhanced definition (ED), or high definition (HD) video
+formats.
+
+Required Properties :
+- compatible: Must be "adi,adv7343"
+
+Optional Properties :
+- adi,power-mode-sleep-mode: on enable the current consumption is reduced to
+			      micro ampere level. All DACs and the internal PLL
+			      circuit are disabled.
+- adi,power-mode-pll-ctrl: PLL and oversampling control. This control allows
+			   internal PLL 1 circuit to be powered down and the
+			   oversampling to be switched off.
+- ad,adv7343-power-mode-dac: array configuring the power on/off DAC's 1..6,
+			      0 = OFF and 1 = ON, Default value when this
+			      property is not specified is <0 0 0 0 0 0>.
+- ad,adv7343-sd-config-dac-out: array configure SD DAC Output's 1 and 2, 0 = OFF
+				 and 1 = ON, Default value when this property is
+				 not specified is <0 0>.
+
+Example:
+
+i2c0@1c22000 {
+	...
+	...
+
+	adv7343@2a {
+		compatible = "adi,adv7343";
+		reg = <0x2a>;
+
+		port {
+			adv7343_1: endpoint {
+					adi,power-mode-sleep-mode;
+					adi,power-mode-pll-ctrl;
+					/* Use DAC1..3, DAC6 */
+					adi,dac-enable = <1 1 1 0 0 1>;
+					/* Use SD DAC output 1 */
+					adi,sd-dac-enable = <1 0>;
+			};
+		};
+	};
+	...
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv748x.txt b/Documentation/devicetree/bindings/media/i2c/adv748x.txt
new file mode 100644
index 000000000..54d1d3bc1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv748x.txt
@@ -0,0 +1,95 @@
+* Analog Devices ADV748X video decoder with HDMI receiver
+
+The ADV7481 and ADV7482 are multi format video decoders with an integrated
+HDMI receiver. They can output CSI-2 on two independent outputs TXA and TXB
+from three input sources HDMI, analog and TTL.
+
+Required Properties:
+
+  - compatible: Must contain one of the following
+    - "adi,adv7481" for the ADV7481
+    - "adi,adv7482" for the ADV7482
+
+  - reg: I2C slave address
+
+Optional Properties:
+
+  - interrupt-names: Should specify the interrupts as "intrq1", "intrq2" and/or
+		     "intrq3". All interrupts are optional. The "intrq3" interrupt
+		     is only available on the adv7481
+  - interrupts: Specify the interrupt lines for the ADV748x
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+	  Name		Type		Port
+	---------------------------------------
+	  AIN0		sink		0
+	  AIN1		sink		1
+	  AIN2		sink		2
+	  AIN3		sink		3
+	  AIN4		sink		4
+	  AIN5		sink		5
+	  AIN6		sink		6
+	  AIN7		sink		7
+	  HDMI		sink		8
+	  TTL		sink		9
+	  TXA		source		10
+	  TXB		source		11
+
+The digital output port nodes must contain at least one endpoint.
+
+Ports are optional if they are not connected to anything at the hardware level.
+
+Example:
+
+	video-receiver@70 {
+		compatible = "adi,adv7482";
+		reg = <0x70>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		interrupt-parent = <&gpio6>;
+		interrupt-names = "intrq1", "intrq2";
+		interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
+			     <31 IRQ_TYPE_LEVEL_LOW>;
+
+		port@7 {
+			reg = <7>;
+
+			adv7482_ain7: endpoint {
+				remote-endpoint = <&cvbs_in>;
+			};
+		};
+
+		port@8 {
+			reg = <8>;
+
+			adv7482_hdmi: endpoint {
+				remote-endpoint = <&hdmi_in>;
+			};
+		};
+
+		port@a {
+			reg = <10>;
+
+			adv7482_txa: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2 3 4>;
+				remote-endpoint = <&csi40_in>;
+			};
+		};
+
+		port@b {
+			reg = <11>;
+
+			adv7482_txb: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1>;
+				remote-endpoint = <&csi20_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/adv7604.txt b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
new file mode 100644
index 000000000..dcf57e7c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/adv7604.txt
@@ -0,0 +1,88 @@
+* Analog Devices ADV7604/11/12 video decoder with HDMI receiver
+
+The ADV7604 and ADV7611/12 are multiformat video decoders with an integrated
+HDMI receiver. The ADV7604 has four multiplexed HDMI inputs and one analog
+input, and the ADV7611 has one HDMI input and no analog input. The 7612 is
+similar to the 7611 but has 2 HDMI inputs.
+
+These device tree bindings support the ADV7611/12 only at the moment.
+
+Required Properties:
+
+  - compatible: Must contain one of the following
+    - "adi,adv7611" for the ADV7611
+    - "adi,adv7612" for the ADV7612
+
+  - reg: I2C slave addresses
+    The ADV76xx has up to thirteen 256-byte maps that can be accessed via the
+    main I2C ports. Each map has it own I2C address and acts as a standard
+    slave device on the I2C bus. The main address is mandatory, others are
+    optional and revert to defaults if not specified.
+
+  - hpd-gpios: References to the GPIOs that control the HDMI hot-plug
+    detection pins, one per HDMI input. The active flag indicates the GPIO
+    level that enables hot-plug detection.
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+  Port			ADV7611    ADV7612
+------------------------------------------------------------
+  HDMI			0             0, 1
+  Digital output	1                2
+
+The digital output port node must contain at least one endpoint.
+
+Optional Properties:
+
+  - reset-gpios: Reference to the GPIO connected to the device's reset pin.
+  - default-input: Select which input is selected after reset.
+  - reg-names : Names of maps with programmable addresses.
+		It can contain any map needing a non-default address.
+		Possible maps names are :
+		  "main", "avlink", "cec", "infoframe", "esdp", "dpp", "afe",
+		  "rep", "edid", "hdmi", "test", "cp", "vdp"
+
+Optional Endpoint Properties:
+
+  The following three properties are defined in video-interfaces.txt and are
+  valid for source endpoints only.
+
+  - hsync-active: Horizontal synchronization polarity. Defaults to active low.
+  - vsync-active: Vertical synchronization polarity. Defaults to active low.
+  - pclk-sample: Pixel clock polarity. Defaults to output on the falling edge.
+
+  If none of hsync-active, vsync-active and pclk-sample is specified the
+  endpoint will use embedded BT.656 synchronization.
+
+Example:
+
+	hdmi_receiver@4c {
+		compatible = "adi,adv7611";
+		/*
+		 * The edid page will be accessible @ 0x66 on the I2C bus. All
+		 * other maps will retain their default addresses.
+		 */
+		reg = <0x4c>, <0x66>;
+		reg-names "main", "edid";
+
+		reset-gpios = <&ioexp 0 GPIO_ACTIVE_LOW>;
+		hpd-gpios = <&ioexp 2 GPIO_ACTIVE_HIGH>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		default-input = <0>;
+
+		port@0 {
+			reg = <0>;
+		};
+		port@1 {
+			reg = <1>;
+			hdmi_in: endpoint {
+				remote-endpoint = <&ccdc_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ak7375.txt b/Documentation/devicetree/bindings/media/i2c/ak7375.txt
new file mode 100644
index 000000000..aa3e24b41
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ak7375.txt
@@ -0,0 +1,8 @@
+Asahi Kasei Microdevices AK7375 voice coil lens driver
+
+AK7375 is a camera voice coil lens.
+
+Mandatory properties:
+
+- compatible: "asahi-kasei,ak7375"
+- reg: I2C slave address
diff --git a/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt
new file mode 100644
index 000000000..bd896e9f6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/aptina,mt9v111.txt
@@ -0,0 +1,46 @@
+* Aptina MT9V111 CMOS sensor
+----------------------------
+
+The Aptina MT9V111 is a 1/4-Inch VGA-format digital image sensor with a core
+based on Aptina MT9V011 sensor and an integrated Image Flow Processor (IFP).
+
+The sensor has an active pixel array of 640x480 pixels and can output a number
+of image resolution and formats controllable through a simple two-wires
+interface.
+
+Required properties:
+--------------------
+
+- compatible: shall be "aptina,mt9v111".
+- clocks: reference to the system clock input provider.
+
+Optional properties:
+--------------------
+
+- enable-gpios: output enable signal, pin name "OE#". Active low.
+- standby-gpios: low power state control signal, pin name "STANDBY".
+  Active high.
+- reset-gpios: chip reset signal, pin name "RESET#". Active low.
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+--------
+
+        &i2c1 {
+                camera@48 {
+                        compatible = "aptina,mt9v111";
+                        reg = <0x48>;
+
+                        clocks = <&camera_clk>;
+
+                        port {
+                                mt9v111_out: endpoint {
+                                        remote-endpoint = <&ceu_in>;
+                                };
+                        };
+                };
+        };
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt
new file mode 100644
index 000000000..b88dcdd41
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9714.txt
@@ -0,0 +1,9 @@
+Dongwoon Anatech DW9714 camera voice coil lens driver
+
+DW9174 is a 10-bit DAC with current sink capability. It is intended
+for driving voice coil lenses in camera modules.
+
+Mandatory properties:
+
+- compatible: "dongwoon,dw9714"
+- reg: I²C slave address
diff --git a/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt
new file mode 100644
index 000000000..c4701f1ea
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/dongwoon,dw9807.txt
@@ -0,0 +1,9 @@
+Dongwoon Anatech DW9807 voice coil lens driver
+
+DW9807 is a 10-bit DAC with current sink capability. It is intended for
+controlling voice coil lenses.
+
+Mandatory properties:
+
+- compatible: "dongwoon,dw9807-vcm"
+- reg: I2C slave address
diff --git a/Documentation/devicetree/bindings/media/i2c/imx274.txt b/Documentation/devicetree/bindings/media/i2c/imx274.txt
new file mode 100644
index 000000000..80f2e8956
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/imx274.txt
@@ -0,0 +1,33 @@
+* Sony 1/2.5-Inch 8.51Mp CMOS Digital Image Sensor
+
+The Sony imx274 is a 1/2.5-inch CMOS active pixel digital image sensor with
+an active array size of 3864H x 2202V. It is programmable through I2C
+interface. The I2C address is fixed to 0x1a as per sensor data sheet.
+Image data is sent through MIPI CSI-2, which is configured as 4 lanes
+at 1440 Mbps.
+
+
+Required Properties:
+- compatible: value should be "sony,imx274" for imx274 sensor
+- reg: I2C bus address of the device
+
+Optional Properties:
+- reset-gpios: Sensor reset GPIO
+
+The imx274 device node should contain one 'port' child node with
+an 'endpoint' subnode. For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+	sensor@1a {
+		compatible = "sony,imx274";
+		reg = <0x1a>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reset-gpios = <&gpio_sensor 0 0>;
+		port {
+			sensor_out: endpoint {
+				remote-endpoint = <&csiss_in>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/max2175.txt b/Documentation/devicetree/bindings/media/i2c/max2175.txt
new file mode 100644
index 000000000..02b4e9cd7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/max2175.txt
@@ -0,0 +1,59 @@
+Maxim Integrated MAX2175 RF to Bits tuner
+-----------------------------------------
+
+The MAX2175 IC is an advanced analog/digital hybrid-radio receiver with
+RF to Bits® front-end designed for software-defined radio solutions.
+
+Required properties:
+--------------------
+- compatible: "maxim,max2175" for MAX2175 RF-to-bits tuner.
+- clocks: clock specifier.
+- port: child port node corresponding to the I2S output, in accordance with
+	the video interface bindings defined in
+	Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+	node must contain at least one endpoint.
+
+Optional properties:
+--------------------
+- maxim,master	      : phandle to the master tuner if it is a slave. This
+			is used to define two tuners in diversity mode
+			(1 master, 1 slave). By default each tuner is an
+			individual master.
+- maxim,refout-load   : load capacitance value (in picofarads) on reference
+			output drive level. The possible load values are:
+			 0 (default - refout disabled)
+			10
+			20
+			30
+			40
+			60
+			70
+- maxim,am-hiz-filter : empty property indicates the AM Hi-Z filter is used
+			in this hardware for AM antenna input.
+
+Example:
+--------
+
+Board specific DTS file
+
+/* Fixed XTAL clock node */
+maxim_xtal: clock {
+	compatible = "fixed-clock";
+	#clock-cells = <0>;
+	clock-frequency = <36864000>;
+};
+
+/* A tuner device instance under i2c bus */
+max2175_0: tuner@60 {
+	compatible = "maxim,max2175";
+	reg = <0x60>;
+	clocks = <&maxim_xtal>;
+	maxim,refout-load = <10>;
+
+	port {
+		max2175_0_ep: endpoint {
+			remote-endpoint = <&slave_rx_device>;
+		};
+	};
+
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9m111.txt b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
new file mode 100644
index 000000000..6b910036b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9m111.txt
@@ -0,0 +1,32 @@
+Micron 1.3Mp CMOS Digital Image Sensor
+
+The Micron MT9M111 is a CMOS active pixel digital image sensor with an active
+array size of 1280H x 1024V. It is programmable through a simple two-wire serial
+interface.
+
+Required Properties:
+- compatible: value should be "micron,mt9m111"
+- clocks: reference to the master clock.
+- clock-names: shall be "mclk".
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c_master {
+		mt9m111@5d {
+			compatible = "micron,mt9m111";
+			reg = <0x5d>;
+			clocks = <&mclk>;
+			clock-names = "mclk";
+
+			remote = <&pxa_camera>;
+			port {
+				mt9m111_1: endpoint {
+					bus-width = <8>;
+					remote-endpoint = <&pxa_camera>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9p031.txt b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
new file mode 100644
index 000000000..cb60443ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9p031.txt
@@ -0,0 +1,40 @@
+* Aptina 1/2.5-Inch 5Mp CMOS Digital Image Sensor
+
+The Aptina MT9P031 is a 1/2.5-inch CMOS active pixel digital image sensor with
+an active array size of 2592H x 1944V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+- compatible: value should be either one among the following
+	(a) "aptina,mt9p031" for mt9p031 sensor
+	(b) "aptina,mt9p031m" for mt9p031m sensor
+
+- input-clock-frequency: Input clock frequency.
+
+- pixel-clock-frequency: Pixel clock frequency.
+
+Optional Properties:
+- reset-gpios: Chip reset GPIO
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		mt9p031@5d {
+			compatible = "aptina,mt9p031";
+			reg = <0x5d>;
+			reset-gpios = <&gpio3 30 0>;
+
+			port {
+				mt9p031_1: endpoint {
+					input-clock-frequency = <6000000>;
+					pixel-clock-frequency = <96000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/mt9v032.txt b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
new file mode 100644
index 000000000..100f0ae43
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/mt9v032.txt
@@ -0,0 +1,41 @@
+* Aptina 1/3-Inch WVGA CMOS Digital Image Sensor
+
+The Aptina MT9V032 is a 1/3-inch CMOS active pixel digital image sensor with
+an active array size of 752H x 480V. It is programmable through a simple
+two-wire serial interface.
+
+Required Properties:
+
+- compatible: value should be either one among the following
+	(a) "aptina,mt9v022" for MT9V022 color sensor
+	(b) "aptina,mt9v022m" for MT9V022 monochrome sensor
+	(c) "aptina,mt9v024" for MT9V024 color sensor
+	(d) "aptina,mt9v024m" for MT9V024 monochrome sensor
+	(e) "aptina,mt9v032" for MT9V032 color sensor
+	(f) "aptina,mt9v032m" for MT9V032 monochrome sensor
+	(g) "aptina,mt9v034" for MT9V034 color sensor
+	(h) "aptina,mt9v034m" for MT9V034 monochrome sensor
+
+Optional Properties:
+
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+	expressed as a 64-bit big-endian integer.
+- reset-gpios: GPIO handle which is connected to the reset pin of the chip.
+- standby-gpios: GPIO handle which is connected to the standby pin of the chip.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	mt9v032@5c {
+		compatible = "aptina,mt9v032";
+		reg = <0x5c>;
+
+		port {
+			mt9v032_out: endpoint {
+				link-frequencies = /bits/ 64
+					<13000000 26600000 27000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt
new file mode 100644
index 000000000..8ee7c7972
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/nokia,smia.txt
@@ -0,0 +1,68 @@
+SMIA/SMIA++ sensor
+
+SMIA (Standard Mobile Imaging Architecture) is an image sensor standard
+defined jointly by Nokia and ST. SMIA++, defined by Nokia, is an extension
+of that. These definitions are valid for both types of sensors.
+
+More detailed documentation can be found in
+Documentation/devicetree/bindings/media/video-interfaces.txt .
+
+
+Mandatory properties
+--------------------
+
+- compatible: "nokia,smia"
+- reg: I2C address (0x10, or an alternative address)
+- vana-supply: Analogue voltage supply (VANA), typically 2,8 volts (sensor
+  dependent).
+- clocks: External clock to the sensor
+- clock-frequency: Frequency of the external clock to the sensor
+- link-frequencies: List of allowed data link frequencies. An array of
+  64-bit elements.
+
+
+Optional properties
+-------------------
+
+- nokia,nvm-size: The size of the NVM, in bytes. If the size is not given,
+  the NVM contents will not be read.
+- reset-gpios: XSHUTDOWN GPIO
+- flash-leds: See ../video-interfaces.txt
+- lens-focus: See ../video-interfaces.txt
+- rotation: Integer property; valid values are 0 (sensor mounted upright)
+	    and 180 (sensor mounted upside down). See
+	    ../video-interfaces.txt .
+
+
+Endpoint node mandatory properties
+----------------------------------
+
+- clock-lanes: <0>
+- data-lanes: <1..n>
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+
+Example
+-------
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	smiapp_1: camera@10 {
+		compatible = "nokia,smia";
+		reg = <0x10>;
+		reset-gpios = <&gpio3 20 0>;
+		vana-supply = <&vaux3>;
+		clocks = <&omap3_isp 0>;
+		clock-frequency = <9600000>;
+		nokia,nvm-size = <512>; /* 8 * 64 */
+		link-frequencies = /bits/ 64 <199200000 210000000 499200000>;
+		port {
+			smiapp_1_1: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+				remote-endpoint = <&csi2a_ep>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2640.txt b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
new file mode 100644
index 000000000..989ce6cb6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2640.txt
@@ -0,0 +1,41 @@
+* Omnivision OV2640 CMOS sensor
+
+The Omnivision OV2640 sensor supports multiple resolutions output, such as
+CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB
+output formats.
+
+Required Properties:
+- compatible: should be "ovti,ov2640"
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+
+Optional Properties:
+- resetb-gpios: reference to the GPIO connected to the resetb pin, if any.
+- pwdn-gpios: reference to the GPIO connected to the pwdn pin, if any.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c1: i2c@f0018000 {
+		ov2640: camera@30 {
+			compatible = "ovti,ov2640";
+			reg = <0x30>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+			resetb-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
+			pwdn-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+			clocks = <&pck0>;
+			clock-names = "xvclk";
+			assigned-clocks = <&pck0>;
+			assigned-clock-rates = <25000000>;
+
+			port {
+				ov2640_0: endpoint {
+					remote-endpoint = <&isi_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2659.txt b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
new file mode 100644
index 000000000..cabc7d827
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2659.txt
@@ -0,0 +1,38 @@
+* OV2659 1/5-Inch 2Mp SOC Camera
+
+The Omnivision OV2659 is a 1/5-inch SOC camera, with an active array size of
+1632H x 1212V. It is programmable through a SCCB. The OV2659 sensor supports
+multiple resolutions output, such as UXGA, SVGA, 720p. It also can support
+YUV422, RGB565/555 or raw RGB output formats.
+
+Required Properties:
+- compatible: Must be "ovti,ov2659"
+- reg: I2C slave address
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+- link-frequencies: target pixel clock frequency.
+
+For further reading on port node refer to
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		 ov2659@30 {
+			compatible = "ovti,ov2659";
+			reg = <0x30>;
+
+			clocks = <&clk_ov2659 0>;
+			clock-names = "xvclk";
+
+			port {
+				ov2659_0: endpoint {
+					remote-endpoint = <&vpfe_ep>;
+					link-frequencies = /bits/ 64 <70000000>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2680.txt b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
new file mode 100644
index 000000000..11e925ed9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2680.txt
@@ -0,0 +1,46 @@
+* Omnivision OV2680 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: should be "ovti,ov2680".
+- clocks: reference to the xvclk input clock.
+- clock-names: should be "xvclk".
+- DOVDD-supply: Digital I/O voltage supply.
+- DVDD-supply: Digital core voltage supply.
+- AVDD-supply: Analog voltage supply.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the powerdown/reset pin,
+               if any. This is an active low signal to the OV2680.
+
+The device node must contain one 'port' child node for its digital output
+video port, and this port must have a single endpoint in accordance with
+ the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0).
+- data-lanes: should be set to <1> (one CSI-2 lane supported).
+
+Example:
+
+&i2c2 {
+	ov2680: camera-sensor@36 {
+		compatible = "ovti,ov2680";
+		reg = <0x36>;
+		clocks = <&osc>;
+		clock-names = "xvclk";
+		reset-gpios = <&gpio1 3 GPIO_ACTIVE_LOW>;
+		DOVDD-supply = <&sw2_reg>;
+		DVDD-supply = <&sw2_reg>;
+		AVDD-supply = <&reg_peri_3p15v>;
+
+		port {
+			ov2680_to_mipi: endpoint {
+				remote-endpoint = <&mipi_from_sensor>;
+				clock-lanes = <0>;
+				data-lanes = <1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov2685.txt b/Documentation/devicetree/bindings/media/i2c/ov2685.txt
new file mode 100644
index 000000000..625c4a8c0
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov2685.txt
@@ -0,0 +1,41 @@
+* Omnivision OV2685 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov2685"
+- clocks: reference to the xvclk input clock
+- clock-names: shall be "xvclk"
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- dvdd-supply: Digital core voltage supply, 1.8 volts
+- reset-gpios: Low active reset gpio
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+The endpoint optional property 'data-lanes' shall be "<1>".
+
+Example:
+&i2c7 {
+	ov2685: camera-sensor@3c {
+		compatible = "ovti,ov2685";
+		reg = <0x3c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&clk_24m_cam>;
+
+		clocks = <&cru SCLK_TESTCLKOUT1>;
+		clock-names = "xvclk";
+
+		avdd-supply = <&pp2800_cam>;
+		dovdd-supply = <&pp1800>;
+		dvdd-supply = <&pp1800>;
+		reset-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+
+		port {
+			ucam_out: endpoint {
+				remote-endpoint = <&mipi_in_ucam>;
+				data-lanes = <1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5640.txt b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
new file mode 100644
index 000000000..c97c2f2da
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5640.txt
@@ -0,0 +1,92 @@
+* Omnivision OV5640 MIPI CSI-2 / parallel sensor
+
+Required Properties:
+- compatible: should be "ovti,ov5640"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+- DOVDD-supply: Digital I/O voltage supply, 1.8 volts
+- AVDD-supply: Analog voltage supply, 2.8 volts
+- DVDD-supply: Digital core voltage supply, 1.5 volts
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the reset pin, if any.
+	       This is an active low signal to the OV5640.
+- powerdown-gpios: reference to the GPIO connected to the powerdown pin,
+		   if any. This is an active high signal to the OV5640.
+- rotation: as defined in
+	    Documentation/devicetree/bindings/media/video-interfaces.txt,
+	    valid values are 0 (sensor mounted upright) and 180 (sensor
+	    mounted upside down).
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+OV5640 can be connected to a MIPI CSI-2 bus or a parallel bus endpoint.
+
+Endpoint node required properties for CSI-2 connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- clock-lanes: should be set to <0> (clock lane on hardware lane 0)
+- data-lanes: should be set to <1> or <1 2> (one or two CSI-2 lanes supported)
+
+Endpoint node required properties for parallel connection are:
+- remote-endpoint: a phandle to the bus receiver's endpoint node.
+- bus-width: shall be set to <8> for 8 bits parallel bus
+	     or <10> for 10 bits parallel bus
+- data-shift: shall be set to <2> for 8 bits parallel bus
+	      (lines 9:2 are used) or <0> for 10 bits parallel bus
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
+	       signal.
+
+Examples:
+
+&i2c1 {
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO>;
+		clock-names = "xclk";
+		DOVDD-supply = <&vgen4_reg>; /* 1.8v */
+		AVDD-supply = <&vgen3_reg>;  /* 2.8v */
+		DVDD-supply = <&vgen2_reg>;  /* 1.5v */
+		powerdown-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
+		rotation = <180>;
+
+		port {
+			/* MIPI CSI-2 bus endpoint */
+			ov5640_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_from_ov5640>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
+
+&i2c1 {
+	ov5640: camera@3c {
+		compatible = "ovti,ov5640";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5640>;
+		reg = <0x3c>;
+		clocks = <&clk_ext_camera>;
+		clock-names = "xclk";
+
+		port {
+			/* Parallel bus endpoint */
+			ov5640_to_parallel: endpoint {
+				remote-endpoint = <&parallel_from_ov5640>;
+				bus-width = <8>;
+				data-shift = <2>; /* lines 9:2 are used */
+				hsync-active = <0>;
+				vsync-active = <0>;
+				pclk-sample = <1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
new file mode 100644
index 000000000..fd7aec9f8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
@@ -0,0 +1,54 @@
+* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor
+
+The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with
+an active array size of 2592H x 1944V. It is programmable through a serial I2C
+interface.
+
+Required Properties:
+- compatible: Value should be "ovti,ov5645".
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock.
+- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
+  to the hardware pin PWDNB which is physically active low.
+- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
+  the hardware pin RESETB.
+- vdddo-supply: Chip digital IO regulator.
+- vdda-supply: Chip analog regulator.
+- vddd-supply: Chip digital core regulator.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	&i2c1 {
+		...
+
+		ov5645: ov5645@78 {
+			compatible = "ovti,ov5645";
+			reg = <0x78>;
+
+			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_rear_default>;
+
+			clocks = <&clks 200>;
+			clock-names = "xclk";
+			clock-frequency = <23880000>;
+
+			vdddo-supply = <&camera_dovdd_1v8>;
+			vdda-supply = <&camera_avdd_2v8>;
+			vddd-supply = <&camera_dvdd_1v2>;
+
+			port {
+				ov5645_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0 2>;
+					remote-endpoint = <&csi0_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5647.txt b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
new file mode 100644
index 000000000..22e44945b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5647.txt
@@ -0,0 +1,35 @@
+Omnivision OV5647 raw image sensor
+---------------------------------
+
+OV5647 is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
+and CCI (I2C compatible) control bus.
+
+Required properties:
+
+- compatible		: "ovti,ov5647".
+- reg			: I2C slave address of the sensor.
+- clocks		: Reference to the xclk clock.
+
+The common video interfaces bindings (see video-interfaces.txt) should be
+used to specify link to the image data receiver. The OV5647 device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Endpoint node mandatory properties:
+
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+Example:
+
+	i2c@2000 {
+		...
+		ov: camera@36 {
+			compatible = "ovti,ov5647";
+			reg = <0x36>;
+			clocks = <&camera_clk>;
+			port {
+				camera_1: endpoint {
+					remote-endpoint = <&csi1_ep1>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov5695.txt b/Documentation/devicetree/bindings/media/i2c/ov5695.txt
new file mode 100644
index 000000000..640a63717
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov5695.txt
@@ -0,0 +1,41 @@
+* Omnivision OV5695 MIPI CSI-2 sensor
+
+Required Properties:
+- compatible: shall be "ovti,ov5695"
+- clocks: reference to the xvclk input clock
+- clock-names: shall be "xvclk"
+- avdd-supply: Analog voltage supply, 2.8 volts
+- dovdd-supply: Digital I/O voltage supply, 1.8 volts
+- dvdd-supply: Digital core voltage supply, 1.2 volts
+- reset-gpios: Low active reset gpio
+
+The device node shall contain one 'port' child node with an
+'endpoint' subnode for its digital output video port,
+in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+The endpoint optional property 'data-lanes' shall be "<1 2>".
+
+Example:
+&i2c7 {
+	ov5695: camera-sensor@36 {
+		compatible = "ovti,ov5695";
+		reg = <0x36>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&clk_24m_cam>;
+
+		clocks = <&cru SCLK_TESTCLKOUT1>;
+		clock-names = "xvclk";
+
+		avdd-supply = <&pp2800_cam>;
+		dovdd-supply = <&pp1800>;
+		dvdd-supply = <&pp1250_cam>;
+		reset-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+
+		port {
+			wcam_out: endpoint {
+				remote-endpoint = <&mipi_in_wcam>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7251.txt b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
new file mode 100644
index 000000000..8281151f7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7251.txt
@@ -0,0 +1,52 @@
+* Omnivision 1/7.5-Inch B&W VGA CMOS Digital Image Sensor
+
+The Omnivision OV7251 is a 1/7.5-Inch CMOS active pixel digital image sensor
+with an active array size of 640H x 480V. It is programmable through a serial
+I2C interface.
+
+Required Properties:
+- compatible: Value should be "ovti,ov7251".
+- clocks: Reference to the xclk clock.
+- clock-names: Should be "xclk".
+- clock-frequency: Frequency of the xclk clock.
+- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
+  to the hardware pin XSHUTDOWN which is physically active low.
+- vdddo-supply: Chip digital IO regulator.
+- vdda-supply: Chip analog regulator.
+- vddd-supply: Chip digital core regulator.
+
+The device node shall contain one 'port' child node with a single 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	&i2c1 {
+		...
+
+		ov7251: camera-sensor@60 {
+			compatible = "ovti,ov7251";
+			reg = <0x60>;
+
+			enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&camera_bw_default>;
+
+			clocks = <&clks 200>;
+			clock-names = "xclk";
+			clock-frequency = <24000000>;
+
+			vdddo-supply = <&camera_dovdd_1v8>;
+			vdda-supply = <&camera_avdd_2v8>;
+			vddd-supply = <&camera_dvdd_1v2>;
+
+			port {
+				ov7251_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0>;
+					remote-endpoint = <&csi0_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7670.txt b/Documentation/devicetree/bindings/media/i2c/ov7670.txt
new file mode 100644
index 000000000..2c972a56f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7670.txt
@@ -0,0 +1,55 @@
+* Omnivision OV7670 CMOS sensor
+
+The Omnivision OV7670 sensor supports multiple resolutions output, such as
+CIF, SVGA, UXGA. It also can support the YUV422/420, RGB565/555 or raw RGB
+output formats.
+
+Required Properties:
+- compatible: should be "ovti,ov7670"
+- clocks: reference to the xclk input clock.
+- clock-names: should be "xclk".
+
+Required Endpoint Properties:
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active is low.
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active is high.
+- ov7670,pclk-hb-disable: a boolean property to suppress pixel clock output
+  signal during horizontal blankings.
+
+The device node must contain one 'port' child node with one 'endpoint' child
+sub-node for its digital output video port, in accordance with the video
+interface bindings defined in:
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	i2c1: i2c@f0018000 {
+		ov7670: camera@21 {
+			compatible = "ovti,ov7670";
+			reg = <0x21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_pck0_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+			reset-gpios = <&pioE 11 GPIO_ACTIVE_LOW>;
+			powerdown-gpios = <&pioE 13 GPIO_ACTIVE_HIGH>;
+			clocks = <&pck0>;
+			clock-names = "xclk";
+			assigned-clocks = <&pck0>;
+			assigned-clock-rates = <25000000>;
+
+			ov7670,pclk-hb-disable;
+
+			port {
+				ov7670_0: endpoint {
+					hsync-active = <0>;
+					vsync-active = <0>;
+
+					remote-endpoint = <&isi_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov772x.txt b/Documentation/devicetree/bindings/media/i2c/ov772x.txt
new file mode 100644
index 000000000..0b3ede5b8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov772x.txt
@@ -0,0 +1,40 @@
+* Omnivision OV7720/OV7725 CMOS sensor
+
+The Omnivision OV7720/OV7725 sensor supports multiple resolutions output,
+such as VGA, QVGA, and any size scaling down from CIF to 40x30. It also can
+support the YUV422, RGB565/555/444, GRB422 or raw RGB output formats.
+
+Required Properties:
+- compatible: shall be one of
+	"ovti,ov7720"
+	"ovti,ov7725"
+- clocks: reference to the xclk input clock.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the RSTB pin which is
+  active low, if any.
+- powerdown-gpios: reference to the GPIO connected to the PWDN pin which is
+  active high, if any.
+
+The device node shall contain one 'port' child node with one child 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+&i2c0 {
+	ov772x: camera@21 {
+		compatible = "ovti,ov7725";
+		reg = <0x21>;
+		reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_LOW>;
+		clocks = <&xclk>;
+
+		port {
+			ov772x_0: endpoint {
+				remote-endpoint = <&vcap1_in0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov7740.txt b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
new file mode 100644
index 000000000..af781c3a5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov7740.txt
@@ -0,0 +1,47 @@
+* Omnivision OV7740 CMOS image sensor
+
+The Omnivision OV7740 image sensor supports multiple output image
+size, such as VGA, and QVGA, CIF and any size smaller. It also
+supports the RAW RGB and YUV output formats.
+
+The common video interfaces bindings (see video-interfaces.txt) should
+be used to specify link to the image data receiver. The OV7740 device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Required Properties:
+- compatible:	"ovti,ov7740".
+- reg:		I2C slave address of the sensor.
+- clocks:	Reference to the xvclk input clock.
+- clock-names:	"xvclk".
+
+Optional Properties:
+- reset-gpios: Rreference to the GPIO connected to the reset_b pin,
+  if any. Active low with pull-ip resistor.
+- powerdown-gpios: Reference to the GPIO connected to the pwdn pin,
+  if any. Active high with pull-down resistor.
+
+Endpoint node mandatory properties:
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+Example:
+
+	i2c1: i2c@fc028000 {
+		ov7740: camera@21 {
+			compatible = "ovti,ov7740";
+			reg = <0x21>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_sensor_power &pinctrl_sensor_reset>;
+			clocks = <&isc>;
+			clock-names = "xvclk";
+			assigned-clocks = <&isc>;
+			assigned-clock-rates = <24000000>;
+			reset-gpios = <&pioA 43 GPIO_ACTIVE_LOW>;
+			powerdown-gpios = <&pioA 44 GPIO_ACTIVE_HIGH>;
+
+			port {
+				ov7740_0: endpoint {
+					remote-endpoint = <&isc_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ov9650.txt b/Documentation/devicetree/bindings/media/i2c/ov9650.txt
new file mode 100644
index 000000000..506dfc528
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ov9650.txt
@@ -0,0 +1,36 @@
+* Omnivision OV9650/OV9652 CMOS sensor
+
+Required Properties:
+- compatible: shall be one of
+	"ovti,ov9650"
+	"ovti,ov9652"
+- clocks: reference to the xvclk input clock.
+
+Optional Properties:
+- reset-gpios: reference to the GPIO connected to the resetb pin, if any.
+  Active is high.
+- powerdown-gpios: reference to the GPIO connected to the pwdn pin, if any.
+  Active is high.
+
+The device node shall contain one 'port' child node with one child 'endpoint'
+subnode for its digital output video port, in accordance with the video
+interface bindings defined in Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+&i2c0 {
+	ov9650: camera@30 {
+		compatible = "ovti,ov9650";
+		reg = <0x30>;
+		reset-gpios = <&axi_gpio_0 0 GPIO_ACTIVE_HIGH>;
+		powerdown-gpios = <&axi_gpio_0 1 GPIO_ACTIVE_HIGH>;
+		clocks = <&xclk>;
+
+		port {
+			ov9650_0: endpoint {
+				remote-endpoint = <&vcap1_in0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt
new file mode 100644
index 000000000..4a3181a3d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/panasonic,amg88xx.txt
@@ -0,0 +1,19 @@
+* Panasonic AMG88xx
+
+The Panasonic family of AMG88xx Grid-Eye sensors allow recording
+8x8 10Hz video which consists of thermal datapoints
+
+Required Properties:
+ - compatible : Must be "panasonic,amg88xx"
+ - reg : i2c address of the device
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		amg88xx@69 {
+			compatible = "panasonic,amg88xx";
+			reg = <0x69>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tc358743.txt b/Documentation/devicetree/bindings/media/i2c/tc358743.txt
new file mode 100644
index 000000000..59102edcf
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tc358743.txt
@@ -0,0 +1,48 @@
+* Toshiba TC358743 HDMI-RX to MIPI CSI2-TX Bridge
+
+The Toshiba TC358743 HDMI-RX to MIPI CSI2-TX (H2C) is a bridge that converts
+a HDMI stream to MIPI CSI-2 TX. It is programmable through I2C.
+
+Required Properties:
+
+- compatible: value should be "toshiba,tc358743"
+- clocks, clock-names: should contain a phandle link to the reference clock
+		       source, the clock input is named "refclk".
+
+Optional Properties:
+
+- reset-gpios: gpio phandle GPIO connected to the reset pin
+- interrupts: GPIO connected to the interrupt pin
+- data-lanes: should be <1 2 3 4> for four-lane operation,
+	      or <1 2> for two-lane operation
+- clock-lanes: should be <0>
+- clock-noncontinuous: Presence of this boolean property decides whether the
+		       MIPI CSI-2 clock is continuous or non-continuous.
+- link-frequencies: List of allowed link frequencies in Hz. Each frequency is
+		    expressed as a 64-bit big-endian integer. The frequency
+		    is half of the bps per lane due to DDR transmission.
+
+For further information on the MIPI CSI-2 endpoint node properties, see
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	tc358743@f {
+		compatible = "toshiba,tc358743";
+		reg = <0x0f>;
+		clocks = <&hdmi_osc>;
+		clock-names = "refclk";
+		reset-gpios = <&gpio6 9 GPIO_ACTIVE_LOW>;
+		interrupt-parent = <&gpio2>;
+		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
+
+		port {
+			tc358743_out: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				data-lanes = <1 2 3 4>;
+				clock-lanes = <0>;
+				clock-noncontinuous;
+				link-frequencies = /bits/ 64 <297000000>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
new file mode 100644
index 000000000..e76167999
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
@@ -0,0 +1,178 @@
+Device-Tree bindings for the NXP TDA1997x HDMI receiver
+
+The TDA19971/73 are HDMI video receivers.
+
+The TDA19971 Video port output pins can be used as follows:
+ - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
+ - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
+ - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
+ - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
+ - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
+ - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
+ - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The TDA19973 Video port output pins can be used as follows:
+ - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
+ - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
+ - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
+ - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
+
+The Video port output pins are mapped via 4-bit 'pin groups' allowing
+for a variety of connection possibilities including swapping pin order within
+pin groups. The video_portcfg device-tree property consists of register mapping
+pairs which map a chip-specific VP output register to a 4-bit pin group. If
+the pin group needs to be bit-swapped you can use the *_S pin-group defines.
+
+Required Properties:
+ - compatible          :
+  - "nxp,tda19971" for the TDA19971
+  - "nxp,tda19973" for the TDA19973
+ - reg                 : I2C slave address
+ - interrupts          : The interrupt number
+ - DOVDD-supply        : Digital I/O supply
+ - DVDD-supply         : Digital Core supply
+ - AVDD-supply         : Analog supply
+ - nxp,vidout-portcfg  : array of pairs mapping VP output pins to pin groups.
+
+Optional Properties:
+ - nxp,audout-format   : DAI bus format: "i2s" or "spdif".
+ - nxp,audout-width    : width of audio output data bus (1-4).
+ - nxp,audout-layout   : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
+ - nxp,audout-mclk-fs  : Multiplication factor between stream rate and codec
+                         mclk.
+
+The port node shall contain one endpoint child node for its digital
+output video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Optional Endpoint Properties:
+  The following three properties are defined in video-interfaces.txt and
+  are valid for the output parallel bus endpoint:
+  - hsync-active: Horizontal synchronization polarity. Defaults to active high.
+  - vsync-active: Vertical synchronization polarity. Defaults to active high.
+  - data-active: Data polarity. Defaults to active high.
+
+Examples:
+ - VP[15:0] connected to IMX6 CSI_DATA[19:4] for 16bit YUV422
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+		 * and Y[11:4] across 16bits in the same pixclk cycle.
+		 */
+		nxp,vidout-portcfg =
+			/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+			/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+			/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+			< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+			/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+			< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp YUV422 semi-planar mode outputs CbCr[11:4]
+		 * and Y[11:4] across 16bits in the same pixclk cycle.
+		 */
+		nxp,vidout-portcfg =
+			/* Y[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_G_Y_11_8 >,
+			/* Y[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_G_Y_7_4 >,
+			/* CbCc[11:8]<->VP[07:04]<->CSI_DATA[11:8] */
+			< TDA1997X_VP24_V07_04 TDA1997X_R_CR_CBCR_11_8 >,
+			/* CbCr[7:4]<->VP[03:00]<->CSI_DATA[7:4] */
+			< TDA1997X_VP24_V03_00 TDA1997X_R_CR_CBCR_7_4 >;
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
+ - VP[15:8] connected to IMX6 CSI_DATA[19:12] for 8bit BT656
+   16bit I2S layout0 with a 128*fs clock (A_WS, AP0, A_CLK pins)
+	hdmi-receiver@48 {
+		compatible = "nxp,tda19971";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_tda1997x>;
+		reg = <0x48>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		DOVDD-supply = <&reg_3p3v>;
+		AVDD-supply = <&reg_1p8v>;
+		DVDD-supply = <&reg_1p8v>;
+		/* audio */
+		#sound-dai-cells = <0>;
+		nxp,audout-format = "i2s";
+		nxp,audout-layout = <0>;
+		nxp,audout-width = <16>;
+		nxp,audout-mclk-fs = <128>;
+		/*
+		 * The 8bpp BT656 mode outputs YCbCr[11:4] across 8bits over
+		 * 2 pixclk cycles.
+		 */
+		nxp,vidout-portcfg =
+			/* YCbCr[11:8]<->VP[15:12]<->CSI_DATA[19:16] */
+			< TDA1997X_VP24_V15_12 TDA1997X_R_CR_CBCR_11_8 >,
+			/* YCbCr[7:4]<->VP[11:08]<->CSI_DATA[15:12] */
+			< TDA1997X_VP24_V11_08 TDA1997X_R_CR_CBCR_7_4 >,
+
+		port {
+			tda1997x_to_ipu1_csi0_mux: endpoint {
+				remote-endpoint = <&ipu1_csi0_mux_from_parallel_sensor>;
+				bus-width = <16>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				data-active = <1>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/ths8200.txt b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
new file mode 100644
index 000000000..285f6ae7d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ths8200.txt
@@ -0,0 +1,19 @@
+* Texas Instruments THS8200 video encoder
+
+The ths8200 device is a digital to analog converter used in DVD players, video
+recorders, set-top boxes.
+
+Required Properties :
+- compatible : value must be "ti,ths8200"
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		ths8200@5c {
+			compatible = "ti,ths8200";
+			reg = <0x5c>;
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
new file mode 100644
index 000000000..e80d5891b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/toshiba,et8ek8.txt
@@ -0,0 +1,55 @@
+Toshiba et8ek8 5MP sensor
+
+Toshiba et8ek8 5MP sensor is an image sensor found in Nokia N900 device
+
+More detailed documentation can be found in
+Documentation/devicetree/bindings/media/video-interfaces.txt .
+
+
+Mandatory properties
+--------------------
+
+- compatible: "toshiba,et8ek8"
+- reg: I2C address (0x3e, or an alternative address)
+- vana-supply: Analogue voltage supply (VANA), 2.8 volts
+- clocks: External clock to the sensor
+- clock-frequency: Frequency of the external clock to the sensor. Camera
+  driver will set this frequency on the external clock. The clock frequency is
+  a pre-determined frequency known to be suitable to the board.
+- reset-gpios: XSHUTDOWN GPIO. The XSHUTDOWN signal is active low. The sensor
+  is in hardware standby mode when the signal is in the low state.
+
+
+Optional properties
+-------------------
+
+- flash-leds: See ../video-interfaces.txt
+- lens-focus: See ../video-interfaces.txt
+
+
+Endpoint node mandatory properties
+----------------------------------
+
+- remote-endpoint: A phandle to the bus receiver's endpoint node.
+
+
+Example
+-------
+
+&i2c3 {
+	clock-frequency = <400000>;
+
+	cam1: camera@3e {
+		compatible = "toshiba,et8ek8";
+		reg = <0x3e>;
+		vana-supply = <&vaux4>;
+		clocks = <&isp 0>;
+		clock-frequency = <9600000>;
+		reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
+		port {
+			csi_cam1: endpoint {
+				remote-endpoint = <&csi_out1>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp514x.txt b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
new file mode 100644
index 000000000..46752cc71
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp514x.txt
@@ -0,0 +1,44 @@
+* Texas Instruments TVP514x video decoder
+
+The TVP5146/TVP5146m2/TVP5147/TVP5147m1 device is high quality, single-chip
+digital video decoder that digitizes and decodes all popular baseband analog
+video formats into digital video component. The tvp514x decoder supports analog-
+to-digital (A/D) conversion of component RGB and YPbPr signals as well as A/D
+conversion and decoding of NTSC, PAL and SECAM composite and S-video into
+component YCbCr.
+
+Required Properties :
+- compatible : value should be either one among the following
+	(a) "ti,tvp5146" for tvp5146 decoder.
+	(b) "ti,tvp5146m2" for tvp5146m2 decoder.
+	(c) "ti,tvp5147" for tvp5147 decoder.
+	(d) "ti,tvp5147m1" for tvp5147m1 decoder.
+
+- hsync-active: HSYNC Polarity configuration for endpoint.
+
+- vsync-active: VSYNC Polarity configuration for endpoint.
+
+- pclk-sample: Clock polarity of the endpoint.
+
+For further reading on port node refer to Documentation/devicetree/bindings/
+media/video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp514x@5c {
+			compatible = "ti,tvp5146";
+			reg = <0x5c>;
+
+			port {
+				tvp514x_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp5150.txt b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
new file mode 100644
index 000000000..8c0fc1a26
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp5150.txt
@@ -0,0 +1,45 @@
+* Texas Instruments TVP5150 and TVP5151 video decoders
+
+The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
+(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
+with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
+
+Required Properties:
+- compatible: value must be "ti,tvp5150"
+- reg: I2C slave address
+
+Optional Properties:
+- pdn-gpios: phandle for the GPIO connected to the PDN pin, if any.
+- reset-gpios: phandle for the GPIO connected to the RESETB pin, if any.
+
+The device node must contain one 'port' child node for its digital output
+video port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Required Endpoint Properties for parallel synchronization:
+
+- hsync-active: active state of the HSYNC signal. Must be <1> (HIGH).
+- vsync-active: active state of the VSYNC signal. Must be <1> (HIGH).
+- field-even-active: field signal level during the even field data
+  transmission. Must be <0>.
+
+If none of hsync-active, vsync-active and field-even-active is specified,
+the endpoint is assumed to use embedded BT.656 synchronization.
+
+Example:
+
+&i2c2 {
+	...
+	tvp5150@5c {
+		compatible = "ti,tvp5150";
+		reg = <0x5c>;
+		pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
+		reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+
+		port {
+			tvp5150_1: endpoint {
+				remote-endpoint = <&ccdc_ep>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/i2c/tvp7002.txt b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
new file mode 100644
index 000000000..5f28b5d9a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/tvp7002.txt
@@ -0,0 +1,53 @@
+* Texas Instruments TV7002 video decoder
+
+The TVP7002 device supports digitizing of video and graphics signal in RGB and
+YPbPr color space.
+
+Required Properties :
+- compatible : Must be "ti,tvp7002"
+
+Optional Properties:
+- hsync-active: HSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- vsync-active: VSYNC Polarity configuration for the bus. Default value when
+  this property is not specified is <0>.
+
+- pclk-sample: Clock polarity of the bus. Default value when this property is
+  not specified is <0>.
+
+- sync-on-green-active: Active state of Sync-on-green signal property of the
+  endpoint.
+  0 = Normal Operation (Active Low, Default)
+  1 = Inverted operation
+
+- field-even-active: Active-high Field ID output polarity control of the bus.
+  Under normal operation, the field ID output is set to logic 1 for an odd field
+  (field 1) and set to logic 0 for an even field (field 0).
+  0 = Normal Operation (Active Low, Default)
+  1 = FID output polarity inverted
+
+For further reading of port node refer Documentation/devicetree/bindings/media/
+video-interfaces.txt.
+
+Example:
+
+	i2c0@1c22000 {
+		...
+		...
+		tvp7002@5c {
+			compatible = "ti,tvp7002";
+			reg = <0x5c>;
+
+			port {
+				tvp7002_1: endpoint {
+					hsync-active = <1>;
+					vsync-active = <1>;
+					pclk-sample = <0>;
+					sync-on-green-active = <1>;
+					field-even-active = <0>;
+				};
+			};
+		};
+		...
+	};
diff --git a/Documentation/devicetree/bindings/media/img-ir-rev1.txt b/Documentation/devicetree/bindings/media/img-ir-rev1.txt
new file mode 100644
index 000000000..ed9ec52b7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/img-ir-rev1.txt
@@ -0,0 +1,34 @@
+* ImgTec Infrared (IR) decoder version 1
+
+This binding is for Imagination Technologies' Infrared decoder block,
+specifically major revision 1.
+
+Required properties:
+- compatible:		Should be "img,ir-rev1"
+- reg:			Physical base address of the controller and length of
+			memory mapped region.
+- interrupts:		The interrupt specifier to the cpu.
+
+Optional properties:
+- clocks:		List of clock specifiers as described in standard
+			clock bindings.
+			Up to 3 clocks may be specified in the following order:
+			1st:	Core clock (defaults to 32.768KHz if omitted).
+			2nd:	System side (fast) clock.
+			3rd:	Power modulation clock.
+- clock-names:		List of clock names corresponding to the clocks
+			specified in the clocks property.
+			Accepted clock names are:
+			"core":	Core clock.
+			"sys":	System clock.
+			"mod":	Power modulation clock.
+
+Example:
+
+	ir@2006200 {
+		compatible = "img,ir-rev1";
+		reg = <0x02006200 0x100>;
+		interrupts = <29 4>;
+		clocks = <&clk_32khz>;
+		clock-names =  "core";
+	};
diff --git a/Documentation/devicetree/bindings/media/imx.txt b/Documentation/devicetree/bindings/media/imx.txt
new file mode 100644
index 000000000..77f4b0a7f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/imx.txt
@@ -0,0 +1,53 @@
+Freescale i.MX Media Video Device
+=================================
+
+Video Media Controller node
+---------------------------
+
+This is the media controller node for video capture support. It is a
+virtual device that lists the camera serial interface nodes that the
+media device will control.
+
+Required properties:
+- compatible : "fsl,imx-capture-subsystem";
+- ports      : Should contain a list of phandles pointing to camera
+		sensor interface ports of IPU devices
+
+example:
+
+capture-subsystem {
+	compatible = "fsl,imx-capture-subsystem";
+	ports = <&ipu1_csi0>, <&ipu1_csi1>;
+};
+
+
+mipi_csi2 node
+--------------
+
+This is the device node for the MIPI CSI-2 Receiver core in the i.MX
+SoC. This is a Synopsys Designware MIPI CSI-2 host controller core
+combined with a D-PHY core mixed into the same register block. In
+addition this device consists of an i.MX-specific "CSI2IPU gasket"
+glue logic, also controlled from the same register block. The CSI2IPU
+gasket demultiplexes the four virtual channel streams from the host
+controller's 32-bit output image bus onto four 16-bit parallel busses
+to the i.MX IPU CSIs.
+
+Required properties:
+- compatible	: "fsl,imx6-mipi-csi2";
+- reg           : physical base address and length of the register set;
+- clocks	: the MIPI CSI-2 receiver requires three clocks: hsi_tx
+		  (the D-PHY clock), video_27m (D-PHY PLL reference
+		  clock), and eim_podf;
+- clock-names	: must contain "dphy", "ref", "pix";
+- port@*        : five port nodes must exist, containing endpoints
+		  connecting to the source and sink devices according to
+		  of_graph bindings. The first port is an input port,
+		  connecting with a MIPI CSI-2 source, and ports 1
+		  through 4 are output ports connecting with parallel
+		  bus sink endpoint nodes and correspond to the four
+		  MIPI CSI-2 virtual channel outputs.
+
+Optional properties:
+- interrupts	: must contain two level-triggered interrupts,
+		  in order: 100 and 101;
diff --git a/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt
new file mode 100644
index 000000000..3813947b4
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt
@@ -0,0 +1,37 @@
+* Mediatek JPEG Decoder
+
+Mediatek JPEG Decoder is the JPEG decode hardware present in Mediatek SoCs
+
+Required properties:
+- compatible : must be one of the following string:
+	"mediatek,mt8173-jpgdec"
+	"mediatek,mt2701-jpgdec"
+- reg : physical base address of the jpeg decoder registers and length of
+  memory mapped region.
+- interrupts : interrupt number to the interrupt controller.
+- clocks: device clocks, see
+  Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
+- clock-names: must contain "jpgdec-smi" and "jpgdec".
+- power-domains: a phandle to the power domain, see
+  Documentation/devicetree/bindings/power/power_domain.txt for details.
+- mediatek,larb: must contain the local arbiters in the current Socs, see
+  Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
+  for details.
+- iommus: should point to the respective IOMMU block with master port as
+  argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
+  for details.
+
+Example:
+	jpegdec: jpegdec@15004000 {
+		compatible = "mediatek,mt2701-jpgdec";
+		reg = <0 0x15004000 0 0x1000>;
+		interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_LOW>;
+		clocks =  <&imgsys CLK_IMG_JPGDEC_SMI>,
+			  <&imgsys CLK_IMG_JPGDEC>;
+		clock-names = "jpgdec-smi",
+			      "jpgdec";
+		power-domains = <&scpsys MT2701_POWER_DOMAIN_ISP>;
+		mediatek,larb = <&larb2>;
+		iommus = <&iommu MT2701_M4U_PORT_JPGDEC_WDMA>,
+			 <&iommu MT2701_M4U_PORT_JPGDEC_BSDMA>;
+	};
diff --git a/Documentation/devicetree/bindings/media/mediatek-mdp.txt b/Documentation/devicetree/bindings/media/mediatek-mdp.txt
new file mode 100644
index 000000000..0d03e3ae2
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/mediatek-mdp.txt
@@ -0,0 +1,103 @@
+* Mediatek Media Data Path
+
+Media Data Path is used for scaling and color space conversion.
+
+Required properties (controller node):
+- compatible: "mediatek,mt8173-mdp"
+- mediatek,vpu: the node of video processor unit, see
+  Documentation/devicetree/bindings/media/mediatek-vpu.txt for details.
+
+Required properties (all function blocks, child node):
+- compatible: Should be one of
+        "mediatek,mt8173-mdp-rdma"  - read DMA
+        "mediatek,mt8173-mdp-rsz"   - resizer
+        "mediatek,mt8173-mdp-wdma"  - write DMA
+        "mediatek,mt8173-mdp-wrot"  - write DMA with rotation
+- reg: Physical base address and length of the function block register space
+- clocks: device clocks, see
+  Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
+- power-domains: a phandle to the power domain, see
+  Documentation/devicetree/bindings/power/power_domain.txt for details.
+
+Required properties (DMA function blocks, child node):
+- compatible: Should be one of
+        "mediatek,mt8173-mdp-rdma"
+        "mediatek,mt8173-mdp-wdma"
+        "mediatek,mt8173-mdp-wrot"
+- iommus: should point to the respective IOMMU block with master port as
+  argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
+  for details.
+- mediatek,larb: must contain the local arbiters in the current Socs, see
+  Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
+  for details.
+
+Example:
+	mdp_rdma0: rdma@14001000 {
+		compatible = "mediatek,mt8173-mdp-rdma";
+			     "mediatek,mt8173-mdp";
+		reg = <0 0x14001000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_RDMA0>,
+			 <&mmsys CLK_MM_MUTEX_32K>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+		iommus = <&iommu M4U_PORT_MDP_RDMA0>;
+		mediatek,larb = <&larb0>;
+		mediatek,vpu = <&vpu>;
+	};
+
+	mdp_rdma1: rdma@14002000 {
+		compatible = "mediatek,mt8173-mdp-rdma";
+		reg = <0 0x14002000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_RDMA1>,
+			 <&mmsys CLK_MM_MUTEX_32K>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+		iommus = <&iommu M4U_PORT_MDP_RDMA1>;
+		mediatek,larb = <&larb4>;
+	};
+
+	mdp_rsz0: rsz@14003000 {
+		compatible = "mediatek,mt8173-mdp-rsz";
+		reg = <0 0x14003000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_RSZ0>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+	};
+
+	mdp_rsz1: rsz@14004000 {
+		compatible = "mediatek,mt8173-mdp-rsz";
+		reg = <0 0x14004000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_RSZ1>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+	};
+
+	mdp_rsz2: rsz@14005000 {
+		compatible = "mediatek,mt8173-mdp-rsz";
+		reg = <0 0x14005000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_RSZ2>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+	};
+
+	mdp_wdma0: wdma@14006000 {
+		compatible = "mediatek,mt8173-mdp-wdma";
+		reg = <0 0x14006000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_WDMA>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+		iommus = <&iommu M4U_PORT_MDP_WDMA>;
+		mediatek,larb = <&larb0>;
+	};
+
+	mdp_wrot0: wrot@14007000 {
+		compatible = "mediatek,mt8173-mdp-wrot";
+		reg = <0 0x14007000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_WROT0>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+		iommus = <&iommu M4U_PORT_MDP_WROT0>;
+		mediatek,larb = <&larb0>;
+	};
+
+	mdp_wrot1: wrot@14008000 {
+		compatible = "mediatek,mt8173-mdp-wrot";
+		reg = <0 0x14008000 0 0x1000>;
+		clocks = <&mmsys CLK_MM_MDP_WROT1>;
+		power-domains = <&scpsys MT8173_POWER_DOMAIN_MM>;
+		iommus = <&iommu M4U_PORT_MDP_WROT1>;
+		mediatek,larb = <&larb4>;
+	};
diff --git a/Documentation/devicetree/bindings/media/mediatek-vcodec.txt b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt
new file mode 100644
index 000000000..2a615d84a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/mediatek-vcodec.txt
@@ -0,0 +1,108 @@
+Mediatek Video Codec
+
+Mediatek Video Codec is the video codec hw present in Mediatek SoCs which
+supports high resolution encoding and decoding functionalities.
+
+Required properties:
+- compatible : "mediatek,mt8173-vcodec-enc" for encoder
+  "mediatek,mt8173-vcodec-dec" for decoder.
+- reg : Physical base address of the video codec registers and length of
+  memory mapped region.
+- interrupts : interrupt number to the cpu.
+- mediatek,larb : must contain the local arbiters in the current Socs.
+- clocks : list of clock specifiers, corresponding to entries in
+  the clock-names property.
+- clock-names: encoder must contain "venc_sel_src", "venc_sel",,
+  "venc_lt_sel_src", "venc_lt_sel", decoder must contain "vcodecpll",
+  "univpll_d2", "clk_cci400_sel", "vdec_sel", "vdecpll", "vencpll",
+  "venc_lt_sel", "vdec_bus_clk_src".
+- iommus : should point to the respective IOMMU block with master port as
+  argument, see Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
+  for details.
+- mediatek,vpu : the node of video processor unit
+
+
+Example:
+
+vcodec_dec: vcodec@16000000 {
+    compatible = "mediatek,mt8173-vcodec-dec";
+    reg = <0 0x16000000 0 0x100>,   /*VDEC_SYS*/
+          <0 0x16020000 0 0x1000>,  /*VDEC_MISC*/
+          <0 0x16021000 0 0x800>,   /*VDEC_LD*/
+          <0 0x16021800 0 0x800>,   /*VDEC_TOP*/
+          <0 0x16022000 0 0x1000>,  /*VDEC_CM*/
+          <0 0x16023000 0 0x1000>,  /*VDEC_AD*/
+          <0 0x16024000 0 0x1000>,  /*VDEC_AV*/
+          <0 0x16025000 0 0x1000>,  /*VDEC_PP*/
+          <0 0x16026800 0 0x800>,   /*VP8_VD*/
+          <0 0x16027000 0 0x800>,   /*VP6_VD*/
+          <0 0x16027800 0 0x800>,   /*VP8_VL*/
+          <0 0x16028400 0 0x400>;   /*VP9_VD*/
+    interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_LOW>;
+    mediatek,larb = <&larb1>;
+    iommus = <&iommu M4U_PORT_HW_VDEC_MC_EXT>,
+             <&iommu M4U_PORT_HW_VDEC_PP_EXT>,
+             <&iommu M4U_PORT_HW_VDEC_AVC_MV_EXT>,
+             <&iommu M4U_PORT_HW_VDEC_PRED_RD_EXT>,
+             <&iommu M4U_PORT_HW_VDEC_PRED_WR_EXT>,
+             <&iommu M4U_PORT_HW_VDEC_UFO_EXT>,
+             <&iommu M4U_PORT_HW_VDEC_VLD_EXT>,
+             <&iommu M4U_PORT_HW_VDEC_VLD2_EXT>;
+    mediatek,vpu = <&vpu>;
+    power-domains = <&scpsys MT8173_POWER_DOMAIN_VDEC>;
+    clocks = <&apmixedsys CLK_APMIXED_VCODECPLL>,
+             <&topckgen CLK_TOP_UNIVPLL_D2>,
+             <&topckgen CLK_TOP_CCI400_SEL>,
+             <&topckgen CLK_TOP_VDEC_SEL>,
+             <&topckgen CLK_TOP_VCODECPLL>,
+             <&apmixedsys CLK_APMIXED_VENCPLL>,
+             <&topckgen CLK_TOP_VENC_LT_SEL>,
+             <&topckgen CLK_TOP_VCODECPLL_370P5>;
+    clock-names = "vcodecpll",
+                  "univpll_d2",
+                  "clk_cci400_sel",
+                  "vdec_sel",
+                  "vdecpll",
+                  "vencpll",
+                  "venc_lt_sel",
+                  "vdec_bus_clk_src";
+  };
+
+  vcodec_enc: vcodec@18002000 {
+    compatible = "mediatek,mt8173-vcodec-enc";
+    reg = <0 0x18002000 0 0x1000>,    /*VENC_SYS*/
+          <0 0x19002000 0 0x1000>;    /*VENC_LT_SYS*/
+    interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_LOW>,
+		 <GIC_SPI 202 IRQ_TYPE_LEVEL_LOW>;
+    mediatek,larb = <&larb3>,
+		    <&larb5>;
+    iommus = <&iommu M4U_PORT_VENC_RCPU>,
+             <&iommu M4U_PORT_VENC_REC>,
+             <&iommu M4U_PORT_VENC_BSDMA>,
+             <&iommu M4U_PORT_VENC_SV_COMV>,
+             <&iommu M4U_PORT_VENC_RD_COMV>,
+             <&iommu M4U_PORT_VENC_CUR_LUMA>,
+             <&iommu M4U_PORT_VENC_CUR_CHROMA>,
+             <&iommu M4U_PORT_VENC_REF_LUMA>,
+             <&iommu M4U_PORT_VENC_REF_CHROMA>,
+             <&iommu M4U_PORT_VENC_NBM_RDMA>,
+             <&iommu M4U_PORT_VENC_NBM_WDMA>,
+             <&iommu M4U_PORT_VENC_RCPU_SET2>,
+             <&iommu M4U_PORT_VENC_REC_FRM_SET2>,
+             <&iommu M4U_PORT_VENC_BSDMA_SET2>,
+             <&iommu M4U_PORT_VENC_SV_COMA_SET2>,
+             <&iommu M4U_PORT_VENC_RD_COMA_SET2>,
+             <&iommu M4U_PORT_VENC_CUR_LUMA_SET2>,
+             <&iommu M4U_PORT_VENC_CUR_CHROMA_SET2>,
+             <&iommu M4U_PORT_VENC_REF_LUMA_SET2>,
+             <&iommu M4U_PORT_VENC_REC_CHROMA_SET2>;
+    mediatek,vpu = <&vpu>;
+    clocks = <&topckgen CLK_TOP_VENCPLL_D2>,
+             <&topckgen CLK_TOP_VENC_SEL>,
+             <&topckgen CLK_TOP_UNIVPLL1_D2>,
+             <&topckgen CLK_TOP_VENC_LT_SEL>;
+    clock-names = "venc_sel_src",
+                  "venc_sel",
+                  "venc_lt_sel_src",
+                  "venc_lt_sel";
+  };
diff --git a/Documentation/devicetree/bindings/media/mediatek-vpu.txt b/Documentation/devicetree/bindings/media/mediatek-vpu.txt
new file mode 100644
index 000000000..2a5bac37f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/mediatek-vpu.txt
@@ -0,0 +1,31 @@
+* Mediatek Video Processor Unit
+
+Video Processor Unit is a HW video controller. It controls HW Codec including
+H.264/VP8/VP9 Decode, H.264/VP8 Encode and Image Processor (scale/rotate/color convert).
+
+Required properties:
+  - compatible: "mediatek,mt8173-vpu"
+  - reg: Must contain an entry for each entry in reg-names.
+  - reg-names: Must include the following entries:
+    "tcm": tcm base
+    "cfg_reg": Main configuration registers base
+  - interrupts: interrupt number to the cpu.
+  - clocks : clock name from clock manager
+  - clock-names: must be main. It is the main clock of VPU
+
+Optional properties:
+  - memory-region: phandle to a node describing memory (see
+    Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt)
+    to be used for VPU extended memory; if not present, VPU may be located
+    anywhere in the memory
+
+Example:
+	vpu: vpu@10020000 {
+		compatible = "mediatek,mt8173-vpu";
+		reg = <0 0x10020000 0 0x30000>,
+		      <0 0x10050000 0 0x100>;
+		reg-names = "tcm", "cfg_reg";
+		interrupts = <GIC_SPI 166 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&topckgen TOP_SCP_SEL>;
+		clock-names = "main";
+	};
diff --git a/Documentation/devicetree/bindings/media/meson-ao-cec.txt b/Documentation/devicetree/bindings/media/meson-ao-cec.txt
new file mode 100644
index 000000000..8671bdb08
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/meson-ao-cec.txt
@@ -0,0 +1,28 @@
+* Amlogic Meson AO-CEC driver
+
+The Amlogic Meson AO-CEC module is present is Amlogic SoCs and its purpose is
+to handle communication between HDMI connected devices over the CEC bus.
+
+Required properties:
+  - compatible : value should be following
+	"amlogic,meson-gx-ao-cec"
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : AO-CEC interrupt number to the CPU.
+  - clocks : from common clock binding: handle to AO-CEC clock.
+  - clock-names : from common clock binding: must contain "core",
+		  corresponding to entry in the clocks property.
+  - hdmi-phandle: phandle to the HDMI controller
+
+Example:
+
+cec_AO: cec@100 {
+	compatible = "amlogic,meson-gx-ao-cec";
+	reg = <0x0 0x00100 0x0 0x14>;
+	interrupts = <GIC_SPI 199 IRQ_TYPE_EDGE_RISING>;
+	clocks = <&clkc_AO CLKID_AO_CEC_32K>;
+	clock-names = "core";
+	hdmi-phandle = <&hdmi_tx>;
+};
diff --git a/Documentation/devicetree/bindings/media/meson-ir.txt b/Documentation/devicetree/bindings/media/meson-ir.txt
new file mode 100644
index 000000000..efd9d29a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/meson-ir.txt
@@ -0,0 +1,20 @@
+* Amlogic Meson IR remote control receiver
+
+Required properties:
+ - compatible	: depending on the platform this should be one of:
+		  - "amlogic,meson6-ir"
+		  - "amlogic,meson8b-ir"
+		  - "amlogic,meson-gxbb-ir"
+ - reg		: physical base address and length of the device registers
+ - interrupts	: a single specifier for the interrupt from the device
+
+Optional properties:
+ - linux,rc-map-name:	see rc.txt file in the same directory.
+
+Example:
+
+	ir-receiver@c8100480 {
+		compatible= "amlogic,meson6-ir";
+		reg = <0xc8100480 0x20>;
+		interrupts = <0 15 1>;
+	};
diff --git a/Documentation/devicetree/bindings/media/mtk-cir.txt b/Documentation/devicetree/bindings/media/mtk-cir.txt
new file mode 100644
index 000000000..5e18087ce
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/mtk-cir.txt
@@ -0,0 +1,28 @@
+Device-Tree bindings for Mediatek consumer IR controller
+found in Mediatek SoC family
+
+Required properties:
+- compatible	    : Should be
+			"mediatek,mt7623-cir": for MT7623 SoC
+			"mediatek,mt7622-cir": for MT7622 SoC
+- clocks	    : list of clock specifiers, corresponding to
+		      entries in clock-names property;
+- clock-names	    : should contain
+			- "clk" entries: for MT7623 SoC
+			- "clk", "bus" entries: for MT7622 SoC
+- interrupts	    : should contain IR IRQ number;
+- reg		    : should contain IO map address for IR.
+
+Optional properties:
+- linux,rc-map-name : see rc.txt file in the same directory.
+
+Example:
+
+cir: cir@10013000 {
+	compatible = "mediatek,mt7623-cir";
+	reg = <0 0x10013000 0 0x1000>;
+	interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>;
+	clocks = <&infracfg CLK_INFRA_IRRX>;
+	clock-names = "clk";
+	linux,rc-map-name = "rc-rc6-mce";
+};
diff --git a/Documentation/devicetree/bindings/media/nokia,n900-ir b/Documentation/devicetree/bindings/media/nokia,n900-ir
new file mode 100644
index 000000000..13a18ce37
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/nokia,n900-ir
@@ -0,0 +1,20 @@
+Device-Tree bindings for LIRC TX driver for Nokia N900(RX51)
+
+Required properties:
+	- compatible: should be "nokia,n900-ir".
+	- pwms: specifies PWM used for IR signal transmission.
+
+Example node:
+
+	pwm9: dmtimer-pwm@9 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer9>;
+		ti,clock-source = <0x00>; /* timer_sys_ck */
+		#pwm-cells = <3>;
+	};
+
+	ir: n900-ir {
+		compatible = "nokia,n900-ir";
+
+		pwms = <&pwm9 0 26316 0>; /* 38000 Hz */
+	};
diff --git a/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt
new file mode 100644
index 000000000..7302e949e
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/nvidia,tegra-vde.txt
@@ -0,0 +1,62 @@
+NVIDIA Tegra Video Decoder Engine
+
+Required properties:
+- compatible : Must contain one of the following values:
+   - "nvidia,tegra20-vde"
+   - "nvidia,tegra30-vde"
+   - "nvidia,tegra114-vde"
+   - "nvidia,tegra124-vde"
+   - "nvidia,tegra132-vde"
+- reg : Must contain an entry for each entry in reg-names.
+- reg-names : Must include the following entries:
+  - sxe
+  - bsev
+  - mbe
+  - ppe
+  - mce
+  - tfe
+  - ppb
+  - vdma
+  - frameid
+- iram : Must contain phandle to the mmio-sram device node that represents
+         IRAM region used by VDE.
+- interrupts : Must contain an entry for each entry in interrupt-names.
+- interrupt-names : Must include the following entries:
+  - sync-token
+  - bsev
+  - sxe
+- clocks : Must include the following entries:
+  - vde
+- resets : Must contain an entry for each entry in reset-names.
+- reset-names : Should include the following entries:
+  - vde
+
+Optional properties:
+- resets : Must contain an entry for each entry in reset-names.
+- reset-names : Must include the following entries:
+  - mc
+
+Example:
+
+video-codec@6001a000 {
+	compatible = "nvidia,tegra20-vde";
+	reg = <0x6001a000 0x1000 /* Syntax Engine */
+	       0x6001b000 0x1000 /* Video Bitstream Engine */
+	       0x6001c000  0x100 /* Macroblock Engine */
+	       0x6001c200  0x100 /* Post-processing Engine */
+	       0x6001c400  0x100 /* Motion Compensation Engine */
+	       0x6001c600  0x100 /* Transform Engine */
+	       0x6001c800  0x100 /* Pixel prediction block */
+	       0x6001ca00  0x100 /* Video DMA */
+	       0x6001d800  0x300 /* Video frame controls */>;
+	reg-names = "sxe", "bsev", "mbe", "ppe", "mce",
+		    "tfe", "ppb", "vdma", "frameid";
+	iram = <&vde_pool>; /* IRAM region */
+	interrupts = <GIC_SPI  9 IRQ_TYPE_LEVEL_HIGH>, /* Sync token interrupt */
+		     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, /* BSE-V interrupt */
+		     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; /* SXE interrupt */
+	interrupt-names = "sync-token", "bsev", "sxe";
+	clocks = <&tegra_car TEGRA20_CLK_VDE>;
+	reset-names = "vde", "mc";
+	resets = <&tegra_car 61>, <&mc TEGRA20_MC_RESET_VDE>;
+};
diff --git a/Documentation/devicetree/bindings/media/pxa-camera.txt b/Documentation/devicetree/bindings/media/pxa-camera.txt
new file mode 100644
index 000000000..bc03ec096
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/pxa-camera.txt
@@ -0,0 +1,42 @@
+Marvell PXA camera host interface
+
+Required properties:
+ - compatible: Should be "marvell,pxa270-qci"
+ - reg: register base and size
+ - interrupts: the interrupt number
+ - any required generic properties defined in video-interfaces.txt
+
+Optional properties:
+ - clocks: input clock (see clock-bindings.txt)
+ - clock-output-names: should contain the name of the clock driving the
+                       sensor master clock MCLK
+ - clock-frequency: host interface is driving MCLK, and MCLK rate is this rate
+
+Example:
+
+	pxa_camera: pxa_camera@50000000 {
+		compatible = "marvell,pxa270-qci";
+		reg = <0x50000000 0x1000>;
+		interrupts = <33>;
+
+		clocks = <&pxa2xx_clks 24>;
+		clock-names = "ciclk";
+		clock-frequency = <50000000>;
+		clock-output-names = "qci_mclk";
+
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Parallel bus endpoint */
+			qci: endpoint@0 {
+				reg = <0>;		/* Local endpoint # */
+				remote-endpoint = <&mt9m111_1>;
+				bus-width = <8>;	/* Used data lines */
+				hsync-active = <0>;	/* Active low */
+				vsync-active = <0>;	/* Active low */
+				pclk-sample = <1>;	/* Rising */
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/qcom,camss.txt b/Documentation/devicetree/bindings/media/qcom,camss.txt
new file mode 100644
index 000000000..09eb6ed99
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/qcom,camss.txt
@@ -0,0 +1,229 @@
+Qualcomm Camera Subsystem
+
+* Properties
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Should contain one of:
+		- "qcom,msm8916-camss"
+		- "qcom,msm8996-camss"
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Register ranges as listed in the reg-names property.
+- reg-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Should contain the following entries:
+		- "csiphy0"
+		- "csiphy0_clk_mux"
+		- "csiphy1"
+		- "csiphy1_clk_mux"
+		- "csiphy2"		(8996 only)
+		- "csiphy2_clk_mux"	(8996 only)
+		- "csid0"
+		- "csid1"
+		- "csid2"		(8996 only)
+		- "csid3"		(8996 only)
+		- "ispif"
+		- "csi_clk_mux"
+		- "vfe0"
+		- "vfe1"		(8996 only)
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Interrupts as listed in the interrupt-names property.
+- interrupt-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Should contain the following entries:
+		- "csiphy0"
+		- "csiphy1"
+		- "csiphy2"		(8996 only)
+		- "csid0"
+		- "csid1"
+		- "csid2"		(8996 only)
+		- "csid3"		(8996 only)
+		- "ispif"
+		- "vfe0"
+		- "vfe1"		(8996 only)
+- power-domains:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A phandle and power domain specifier pairs to the
+		    power domain which is responsible for collapsing
+		    and restoring power to the peripheral.
+- clocks:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A list of phandle and clock specifier pairs as listed
+		    in clock-names property.
+- clock-names:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Should contain the following entries:
+		- "top_ahb"
+		- "ispif_ahb"
+		- "csiphy0_timer"
+		- "csiphy1_timer"
+		- "csiphy2_timer"	(8996 only)
+		- "csi0_ahb"
+		- "csi0"
+		- "csi0_phy"
+		- "csi0_pix"
+		- "csi0_rdi"
+		- "csi1_ahb"
+		- "csi1"
+		- "csi1_phy"
+		- "csi1_pix"
+		- "csi1_rdi"
+		- "csi2_ahb"		(8996 only)
+		- "csi2"		(8996 only)
+		- "csi2_phy"		(8996 only)
+		- "csi2_pix"		(8996 only)
+		- "csi2_rdi"		(8996 only)
+		- "csi3_ahb"		(8996 only)
+		- "csi3"		(8996 only)
+		- "csi3_phy"		(8996 only)
+		- "csi3_pix"		(8996 only)
+		- "csi3_rdi"		(8996 only)
+		- "ahb"
+		- "vfe0"
+		- "csi_vfe0"
+		- "vfe0_ahb",		(8996 only)
+		- "vfe0_stream",	(8996 only)
+		- "vfe1",		(8996 only)
+		- "csi_vfe1",		(8996 only)
+		- "vfe1_ahb",		(8996 only)
+		- "vfe1_stream",	(8996 only)
+		- "vfe_ahb"
+		- "vfe_axi"
+- vdda-supply:
+	Usage: required
+	Value type: <phandle>
+	Definition: A phandle to voltage supply for CSI2.
+- iommus:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A list of phandle and IOMMU specifier pairs.
+
+* Nodes
+
+- ports:
+	Usage: required
+	Definition: As described in video-interfaces.txt in same directory.
+	Properties:
+		- reg:
+			Usage: required
+			Value type: <u32>
+			Definition: Selects CSI2 PHY interface - PHY0, PHY1
+				    or PHY2 (8996 only)
+	Endpoint node properties:
+		- clock-lanes:
+			Usage: required
+			Value type: <u32>
+			Definition: The physical clock lane index. On 8916
+				    the value must always be <1> as the physical
+				    clock lane is lane 1. On 8996 the value must
+				    always be <7> as the hardware supports D-PHY
+				    and C-PHY, indexes are in a common set and
+				    D-PHY physical clock lane is labeled as 7.
+		- data-lanes:
+			Usage: required
+			Value type: <prop-encoded-array>
+			Definition: An array of physical data lanes indexes.
+				    Position of an entry determines the logical
+				    lane number, while the value of an entry
+				    indicates physical lane index. Lane swapping
+				    is supported. Physical lane indexes for
+				    8916: 0, 2, 3, 4; for 8996: 0, 1, 2, 3.
+
+* An Example
+
+	camss: camss@1b00000 {
+		compatible = "qcom,msm8916-camss";
+		reg = <0x1b0ac00 0x200>,
+			<0x1b00030 0x4>,
+			<0x1b0b000 0x200>,
+			<0x1b00038 0x4>,
+			<0x1b08000 0x100>,
+			<0x1b08400 0x100>,
+			<0x1b0a000 0x500>,
+			<0x1b00020 0x10>,
+			<0x1b10000 0x1000>;
+		reg-names = "csiphy0",
+			"csiphy0_clk_mux",
+			"csiphy1",
+			"csiphy1_clk_mux",
+			"csid0",
+			"csid1",
+			"ispif",
+			"csi_clk_mux",
+			"vfe0";
+		interrupts = <GIC_SPI 78 0>,
+			<GIC_SPI 79 0>,
+			<GIC_SPI 51 0>,
+			<GIC_SPI 52 0>,
+			<GIC_SPI 55 0>,
+			<GIC_SPI 57 0>;
+		interrupt-names = "csiphy0",
+			"csiphy1",
+			"csid0",
+			"csid1",
+			"ispif",
+			"vfe0";
+		power-domains = <&gcc VFE_GDSC>;
+		clocks = <&gcc GCC_CAMSS_TOP_AHB_CLK>,
+			<&gcc GCC_CAMSS_ISPIF_AHB_CLK>,
+			<&gcc GCC_CAMSS_CSI0PHYTIMER_CLK>,
+			<&gcc GCC_CAMSS_CSI1PHYTIMER_CLK>,
+			<&gcc GCC_CAMSS_CSI0_AHB_CLK>,
+			<&gcc GCC_CAMSS_CSI0_CLK>,
+			<&gcc GCC_CAMSS_CSI0PHY_CLK>,
+			<&gcc GCC_CAMSS_CSI0PIX_CLK>,
+			<&gcc GCC_CAMSS_CSI0RDI_CLK>,
+			<&gcc GCC_CAMSS_CSI1_AHB_CLK>,
+			<&gcc GCC_CAMSS_CSI1_CLK>,
+			<&gcc GCC_CAMSS_CSI1PHY_CLK>,
+			<&gcc GCC_CAMSS_CSI1PIX_CLK>,
+			<&gcc GCC_CAMSS_CSI1RDI_CLK>,
+			<&gcc GCC_CAMSS_AHB_CLK>,
+			<&gcc GCC_CAMSS_VFE0_CLK>,
+			<&gcc GCC_CAMSS_CSI_VFE0_CLK>,
+			<&gcc GCC_CAMSS_VFE_AHB_CLK>,
+			<&gcc GCC_CAMSS_VFE_AXI_CLK>;
+		clock-names = "top_ahb",
+			"ispif_ahb",
+			"csiphy0_timer",
+			"csiphy1_timer",
+			"csi0_ahb",
+			"csi0",
+			"csi0_phy",
+			"csi0_pix",
+			"csi0_rdi",
+			"csi1_ahb",
+			"csi1",
+			"csi1_phy",
+			"csi1_pix",
+			"csi1_rdi",
+			"ahb",
+			"vfe0",
+			"csi_vfe0",
+			"vfe_ahb",
+			"vfe_axi";
+		vdda-supply = <&pm8916_l2>;
+		iommus = <&apps_iommu 3>;
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				reg = <0>;
+				csiphy0_ep: endpoint {
+					clock-lanes = <1>;
+					data-lanes = <0 2>;
+					remote-endpoint = <&ov5645_ep>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/qcom,venus.txt b/Documentation/devicetree/bindings/media/qcom,venus.txt
new file mode 100644
index 000000000..00d0d1bf7
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/qcom,venus.txt
@@ -0,0 +1,108 @@
+* Qualcomm Venus video encoder/decoder accelerators
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Value should contain one of:
+		- "qcom,msm8916-venus"
+		- "qcom,msm8996-venus"
+		- "qcom,sdm845-venus"
+- reg:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Register base address and length of the register map.
+- interrupts:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: Should contain interrupt line number.
+- clocks:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A List of phandle and clock specifier pairs as listed
+		    in clock-names property.
+- clock-names:
+	Usage: required for msm8916
+	Value type: <stringlist>
+	Definition: Should contain the following entries:
+		- "core"	Core video accelerator clock
+		- "iface"	Video accelerator AHB clock
+		- "bus"		Video accelerator AXI clock
+- clock-names:
+	Usage: required for msm8996
+	Value type: <stringlist>
+	Definition: Should contain the following entries:
+		- "core"	Core video accelerator clock
+		- "iface"	Video accelerator AHB clock
+		- "bus"		Video accelerator AXI clock
+		- "mbus"	Video MAXI clock
+- power-domains:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A phandle and power domain specifier pairs to the
+		    power domain which is responsible for collapsing
+		    and restoring power to the peripheral.
+- iommus:
+	Usage: required
+	Value type: <prop-encoded-array>
+	Definition: A list of phandle and IOMMU specifier pairs.
+- memory-region:
+	Usage: required
+	Value type: <phandle>
+	Definition: reference to the reserved-memory for the firmware
+		    memory region.
+
+* Subnodes
+The Venus video-codec node must contain two subnodes representing
+video-decoder and video-encoder.
+
+Every of video-encoder or video-decoder subnode should have:
+
+- compatible:
+	Usage: required
+	Value type: <stringlist>
+	Definition: Value should contain "venus-decoder" or "venus-encoder"
+- clocks:
+	Usage: required for msm8996
+	Value type: <prop-encoded-array>
+	Definition: A List of phandle and clock specifier pairs as listed
+		    in clock-names property.
+- clock-names:
+	Usage: required for msm8996
+	Value type: <stringlist>
+	Definition: Should contain the following entries:
+		- "core"	Subcore video accelerator clock
+
+- power-domains:
+	Usage: required for msm8996
+	Value type: <prop-encoded-array>
+	Definition: A phandle and power domain specifier pairs to the
+		    power domain which is responsible for collapsing
+		    and restoring power to the subcore.
+
+* An Example
+	video-codec@1d00000 {
+		compatible = "qcom,msm8916-venus";
+		reg = <0x01d00000 0xff000>;
+		interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&gcc GCC_VENUS0_VCODEC0_CLK>,
+			 <&gcc GCC_VENUS0_AHB_CLK>,
+			 <&gcc GCC_VENUS0_AXI_CLK>;
+		clock-names = "core", "iface", "bus";
+		power-domains = <&gcc VENUS_GDSC>;
+		iommus = <&apps_iommu 5>;
+		memory-region = <&venus_mem>;
+
+		video-decoder {
+			compatible = "venus-decoder";
+			clocks = <&mmcc VIDEO_SUBCORE0_CLK>;
+			clock-names = "core";
+			power-domains = <&mmcc VENUS_CORE0_GDSC>;
+		};
+
+		video-encoder {
+			compatible = "venus-encoder";
+			clocks = <&mmcc VIDEO_SUBCORE1_CLK>;
+			clock-names = "core";
+			power-domains = <&mmcc VENUS_CORE1_GDSC>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/rc.txt b/Documentation/devicetree/bindings/media/rc.txt
new file mode 100644
index 000000000..d3e7a012b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/rc.txt
@@ -0,0 +1,117 @@
+The following properties are common to the infrared remote controllers:
+
+- linux,rc-map-name: string, specifies the scancode/key mapping table
+  defined in-kernel for the remote controller. Support values are:
+  * "rc-adstech-dvb-t-pci"
+  * "rc-alink-dtu-m"
+  * "rc-anysee"
+  * "rc-apac-viewcomp"
+  * "rc-asus-pc39"
+  * "rc-asus-ps3-100"
+  * "rc-ati-tv-wonder-hd-600"
+  * "rc-ati-x10"
+  * "rc-avermedia-a16d"
+  * "rc-avermedia-cardbus"
+  * "rc-avermedia-dvbt"
+  * "rc-avermedia-m135a"
+  * "rc-avermedia-m733a-rm-k6"
+  * "rc-avermedia-rm-ks"
+  * "rc-avermedia"
+  * "rc-avertv-303"
+  * "rc-azurewave-ad-tu700"
+  * "rc-behold-columbus"
+  * "rc-behold"
+  * "rc-budget-ci-old"
+  * "rc-cec"
+  * "rc-cinergy-1400"
+  * "rc-cinergy"
+  * "rc-delock-61959"
+  * "rc-dib0700-nec"
+  * "rc-dib0700-rc5"
+  * "rc-digitalnow-tinytwin"
+  * "rc-digittrade"
+  * "rc-dm1105-nec"
+  * "rc-dntv-live-dvbt-pro"
+  * "rc-dntv-live-dvb-t"
+  * "rc-dtt200u"
+  * "rc-dvbsky"
+  * "rc-empty"
+  * "rc-em-terratec"
+  * "rc-encore-enltv2"
+  * "rc-encore-enltv-fm53"
+  * "rc-encore-enltv"
+  * "rc-evga-indtube"
+  * "rc-eztv"
+  * "rc-flydvb"
+  * "rc-flyvideo"
+  * "rc-fusionhdtv-mce"
+  * "rc-gadmei-rm008z"
+  * "rc-geekbox"
+  * "rc-genius-tvgo-a11mce"
+  * "rc-gotview7135"
+  * "rc-hauppauge"
+  * "rc-imon-mce"
+  * "rc-imon-pad"
+  * "rc-iodata-bctv7e"
+  * "rc-it913x-v1"
+  * "rc-it913x-v2"
+  * "rc-kaiomy"
+  * "rc-kworld-315u"
+  * "rc-kworld-pc150u"
+  * "rc-kworld-plus-tv-analog"
+  * "rc-leadtek-y04g0051"
+  * "rc-lirc"
+  * "rc-lme2510"
+  * "rc-manli"
+  * "rc-medion-x10"
+  * "rc-medion-x10-digitainer"
+  * "rc-medion-x10-or2x"
+  * "rc-msi-digivox-ii"
+  * "rc-msi-digivox-iii"
+  * "rc-msi-tvanywhere-plus"
+  * "rc-msi-tvanywhere"
+  * "rc-nebula"
+  * "rc-nec-terratec-cinergy-xs"
+  * "rc-norwood"
+  * "rc-npgtech"
+  * "rc-pctv-sedna"
+  * "rc-pinnacle-color"
+  * "rc-pinnacle-grey"
+  * "rc-pinnacle-pctv-hd"
+  * "rc-pixelview-new"
+  * "rc-pixelview"
+  * "rc-pixelview-002t"
+  * "rc-pixelview-mk12"
+  * "rc-powercolor-real-angel"
+  * "rc-proteus-2309"
+  * "rc-purpletv"
+  * "rc-pv951"
+  * "rc-hauppauge"
+  * "rc-rc5-tv"
+  * "rc-rc6-mce"
+  * "rc-real-audio-220-32-keys"
+  * "rc-reddo"
+  * "rc-snapstream-firefly"
+  * "rc-streamzap"
+  * "rc-tbs-nec"
+  * "rc-technisat-ts35"
+  * "rc-technisat-usb2"
+  * "rc-terratec-cinergy-c-pci"
+  * "rc-terratec-cinergy-s2-hd"
+  * "rc-terratec-cinergy-xs"
+  * "rc-terratec-slim"
+  * "rc-terratec-slim-2"
+  * "rc-tevii-nec"
+  * "rc-tivo"
+  * "rc-total-media-in-hand"
+  * "rc-total-media-in-hand-02"
+  * "rc-trekstor"
+  * "rc-tt-1500"
+  * "rc-twinhan-dtv-cab-ci"
+  * "rc-twinhan1027"
+  * "rc-videomate-k100"
+  * "rc-videomate-s350"
+  * "rc-videomate-tv-pvr"
+  * "rc-winfast"
+  * "rc-winfast-usbii-deluxe"
+  * "rc-su3000"
diff --git a/Documentation/devicetree/bindings/media/rcar_vin.txt b/Documentation/devicetree/bindings/media/rcar_vin.txt
new file mode 100644
index 000000000..2f420050d
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/rcar_vin.txt
@@ -0,0 +1,213 @@
+Renesas R-Car Video Input driver (rcar_vin)
+-------------------------------------------
+
+The rcar_vin device provides video input capabilities for the Renesas R-Car
+family of devices.
+
+Each VIN instance has a single parallel input that supports RGB and YUV video,
+with both external synchronization and BT.656 synchronization for the latter.
+Depending on the instance the VIN input is connected to external SoC pins, or
+on Gen3 platforms to a CSI-2 receiver.
+
+ - compatible: Must be one or more of the following
+   - "renesas,vin-r8a7743" for the R8A7743 device
+   - "renesas,vin-r8a7745" for the R8A7745 device
+   - "renesas,vin-r8a7778" for the R8A7778 device
+   - "renesas,vin-r8a7779" for the R8A7779 device
+   - "renesas,vin-r8a7790" for the R8A7790 device
+   - "renesas,vin-r8a7791" for the R8A7791 device
+   - "renesas,vin-r8a7792" for the R8A7792 device
+   - "renesas,vin-r8a7793" for the R8A7793 device
+   - "renesas,vin-r8a7794" for the R8A7794 device
+   - "renesas,vin-r8a7795" for the R8A7795 device
+   - "renesas,vin-r8a7796" for the R8A7796 device
+   - "renesas,vin-r8a77965" for the R8A77965 device
+   - "renesas,vin-r8a77970" for the R8A77970 device
+   - "renesas,vin-r8a77995" for the R8A77995 device
+   - "renesas,rcar-gen2-vin" for a generic R-Car Gen2 or RZ/G1 compatible
+     device.
+
+   When compatible with the generic version nodes must list the
+   SoC-specific version corresponding to the platform first
+   followed by the generic version.
+
+ - reg: the register base and size for the device registers
+ - interrupts: the interrupt for the device
+ - clocks: Reference to the parent clock
+
+Additionally, an alias named vinX will need to be created to specify
+which video input device this is.
+
+The per-board settings Gen2 platforms:
+
+- port - sub-node describing a single endpoint connected to the VIN
+  from external SoC pins as described in video-interfaces.txt[1].
+  Only the first one will be considered as each vin interface has one
+  input port.
+
+  - Optional properties for endpoint nodes:
+    - hsync-active: see [1] for description. Default is active high.
+    - vsync-active: see [1] for description. Default is active high.
+      If both HSYNC and VSYNC polarities are not specified, embedded
+      synchronization is selected.
+    - field-active-even: see [1] for description. Default is active high.
+    - bus-width: see [1] for description. The selected bus width depends on
+      the SoC type and selected input image format.
+      Valid values are: 8, 10, 12, 16, 24 and 32.
+    - data-shift: see [1] for description. Valid values are 0 and 8.
+    - data-enable-active: polarity of CLKENB signal, see [1] for
+      description. Default is active high.
+
+The per-board settings Gen3 platforms:
+
+Gen3 platforms can support both a single connected parallel input source
+from external SoC pins (port@0) and/or multiple parallel input sources
+from local SoC CSI-2 receivers (port@1) depending on SoC.
+
+- renesas,id - ID number of the VIN, VINx in the documentation.
+- ports
+    - port@0 - sub-node describing a single endpoint connected to the VIN
+      from external SoC pins as described in video-interfaces.txt[1].
+      Describing more than one endpoint in port@0 is invalid. Only VIN
+      instances that are connected to external pins should have port@0.
+
+      Endpoint nodes of port@0 support the optional properties listed in
+      the Gen2 per-board settings description.
+
+    - port@1 - sub-nodes describing one or more endpoints connected to
+      the VIN from local SoC CSI-2 receivers. The endpoint numbers must
+      use the following schema.
+
+        - endpoint@0 - sub-node describing the endpoint connected to CSI20
+        - endpoint@1 - sub-node describing the endpoint connected to CSI21
+        - endpoint@2 - sub-node describing the endpoint connected to CSI40
+        - endpoint@3 - sub-node describing the endpoint connected to CSI41
+
+      Endpoint nodes of port@1 do not support any optional endpoint property.
+
+Device node example for Gen2 platforms
+--------------------------------------
+
+        aliases {
+                vin0 = &vin0;
+        };
+
+        vin0: vin@e6ef0000 {
+                compatible = "renesas,vin-r8a7790", "renesas,rcar-gen2-vin";
+                clocks = <&mstp8_clks R8A7790_CLK_VIN0>;
+                reg = <0 0xe6ef0000 0 0x1000>;
+                interrupts = <0 188 IRQ_TYPE_LEVEL_HIGH>;
+                status = "disabled";
+        };
+
+Board setup example for Gen2 platforms (vin1 composite video input)
+-------------------------------------------------------------------
+
+&i2c2   {
+        status = "okay";
+        pinctrl-0 = <&i2c2_pins>;
+        pinctrl-names = "default";
+
+        adv7180@20 {
+                compatible = "adi,adv7180";
+                reg = <0x20>;
+                remote = <&vin1>;
+
+                port {
+                        adv7180: endpoint {
+                                bus-width = <8>;
+                                remote-endpoint = <&vin1ep0>;
+                        };
+                };
+        };
+};
+
+/* composite video input */
+&vin1 {
+        pinctrl-0 = <&vin1_pins>;
+        pinctrl-names = "default";
+
+        status = "okay";
+
+        port {
+                vin1ep0: endpoint {
+                        remote-endpoint = <&adv7180>;
+                        bus-width = <8>;
+                };
+        };
+};
+
+Device node example for Gen3 platforms
+--------------------------------------
+
+        vin0: video@e6ef0000 {
+                compatible = "renesas,vin-r8a7795";
+                reg = <0 0xe6ef0000 0 0x1000>;
+                interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
+                clocks = <&cpg CPG_MOD 811>;
+                power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+                resets = <&cpg 811>;
+                renesas,id = <0>;
+
+                ports {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        port@1 {
+                                #address-cells = <1>;
+                                #size-cells = <0>;
+
+                                reg = <1>;
+
+                                vin0csi20: endpoint@0 {
+                                        reg = <0>;
+                                        remote-endpoint= <&csi20vin0>;
+                                };
+                                vin0csi21: endpoint@1 {
+                                        reg = <1>;
+                                        remote-endpoint= <&csi21vin0>;
+                                };
+                                vin0csi40: endpoint@2 {
+                                        reg = <2>;
+                                        remote-endpoint= <&csi40vin0>;
+                                };
+                        };
+                };
+        };
+
+        csi20: csi2@fea80000 {
+                compatible = "renesas,r8a7795-csi2";
+                reg = <0 0xfea80000 0 0x10000>;
+                interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
+                clocks = <&cpg CPG_MOD 714>;
+                power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+                resets = <&cpg 714>;
+
+                ports {
+                        #address-cells = <1>;
+                        #size-cells = <0>;
+
+                        port@0 {
+                                reg = <0>;
+                                csi20_in: endpoint {
+                                        clock-lanes = <0>;
+                                        data-lanes = <1>;
+                                        remote-endpoint = <&adv7482_txb>;
+                                };
+                        };
+
+                        port@1 {
+                                #address-cells = <1>;
+                                #size-cells = <0>;
+
+                                reg = <1>;
+
+                                csi20vin0: endpoint@0 {
+                                        reg = <0>;
+                                        remote-endpoint = <&vin0csi20>;
+                                };
+                        };
+                };
+        };
+
+[1] video-interfaces.txt common video media interface
diff --git a/Documentation/devicetree/bindings/media/renesas,ceu.txt b/Documentation/devicetree/bindings/media/renesas,ceu.txt
new file mode 100644
index 000000000..8a7a616e9
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,ceu.txt
@@ -0,0 +1,82 @@
+Renesas Capture Engine Unit (CEU)
+----------------------------------------------
+
+The Capture Engine Unit is the image capture interface found in the Renesas
+SH Mobile, R-Mobile and RZ SoCs.
+
+The interface supports a single parallel input with data bus width of 8 or 16
+bits.
+
+Required properties:
+- compatible: Shall be one of the following values:
+	"renesas,r7s72100-ceu" for CEU units found in RZ/A1H and RZ/A1M SoCs
+	"renesas,r8a7740-ceu" for CEU units found in R-Mobile A1 R8A7740 SoCs
+- reg: Registers address base and size.
+- interrupts: The interrupt specifier.
+
+The CEU supports a single parallel input and should contain a single 'port'
+subnode with a single 'endpoint'. Connection to input devices are modeled
+according to the video interfaces OF bindings specified in:
+Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Optional endpoint properties applicable to parallel input bus described in
+the above mentioned "video-interfaces.txt" file are supported.
+
+- hsync-active: Active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+  If property is not present, default is active high.
+- vsync-active: Active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+  If property is not present, default is active high.
+
+Example:
+
+The example describes the connection between the Capture Engine Unit and an
+OV7670 image sensor connected to i2c1 interface.
+
+ceu: ceu@e8210000 {
+	reg = <0xe8210000 0x209c>;
+	compatible = "renesas,r7s72100-ceu";
+	interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&vio_pins>;
+
+	status = "okay";
+
+	port {
+		ceu_in: endpoint {
+			remote-endpoint = <&ov7670_out>;
+
+			hsync-active = <1>;
+			vsync-active = <0>;
+		};
+	};
+};
+
+i2c1: i2c@fcfee400 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+
+	status = "okay";
+
+	clock-frequency = <100000>;
+
+	ov7670: camera@21 {
+		compatible = "ovti,ov7670";
+		reg = <0x21>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&vio_pins>;
+
+		reset-gpios = <&port3 11 GPIO_ACTIVE_LOW>;
+		powerdown-gpios = <&port3 12 GPIO_ACTIVE_HIGH>;
+
+		port {
+			ov7670_out: endpoint {
+				remote-endpoint = <&ceu_in>;
+
+				hsync-active = <1>;
+				vsync-active = <0>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/renesas,drif.txt b/Documentation/devicetree/bindings/media/renesas,drif.txt
new file mode 100644
index 000000000..0d8974aa8
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,drif.txt
@@ -0,0 +1,177 @@
+Renesas R-Car Gen3 Digital Radio Interface controller (DRIF)
+------------------------------------------------------------
+
+R-Car Gen3 DRIF is a SPI like receive only slave device. A general
+representation of DRIF interfacing with a master device is shown below.
+
++---------------------+                +---------------------+
+|                     |-----SCK------->|CLK                  |
+|       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
+|                     |-----SD0------->|D0                   |
+|                     |-----SD1------->|D1                   |
++---------------------+                +---------------------+
+
+As per datasheet, each DRIF channel (drifn) is made up of two internal
+channels (drifn0 & drifn1). These two internal channels share the common
+CLK & SYNC. Each internal channel has its own dedicated resources like
+irq, dma channels, address space & clock. This internal split is not
+visible to the external master device.
+
+The device tree model represents each internal channel as a separate node.
+The internal channels sharing the CLK & SYNC are tied together by their
+phandles using a property called "renesas,bonding". For the rest of
+the documentation, unless explicitly stated, the word channel implies an
+internal channel.
+
+When both internal channels are enabled they need to be managed together
+as one (i.e.) they cannot operate alone as independent devices. Out of the
+two, one of them needs to act as a primary device that accepts common
+properties of both the internal channels. This channel is identified by a
+property called "renesas,primary-bond".
+
+To summarize,
+   - When both the internal channels that are bonded together are enabled,
+     the zeroth channel is selected as primary-bond. This channels accepts
+     properties common to all the members of the bond.
+   - When only one of the bonded channels need to be enabled, the property
+     "renesas,bonding" or "renesas,primary-bond" will have no effect. That
+     enabled channel can act alone as any other independent device.
+
+Required properties of an internal channel:
+-------------------------------------------
+- compatible:	"renesas,r8a7795-drif" if DRIF controller is a part of R8A7795 SoC.
+		"renesas,r8a7796-drif" if DRIF controller is a part of R8A7796 SoC.
+		"renesas,rcar-gen3-drif" for a generic R-Car Gen3 compatible device.
+
+		When compatible with the generic version, nodes must list the
+		SoC-specific version corresponding to the platform first
+		followed by the generic version.
+
+- reg: offset and length of that channel.
+- interrupts: associated with that channel.
+- clocks: phandle and clock specifier of that channel.
+- clock-names: clock input name string: "fck".
+- dmas: phandles to the DMA channels.
+- dma-names: names of the DMA channel: "rx".
+- renesas,bonding: phandle to the other channel.
+
+Optional properties of an internal channel:
+-------------------------------------------
+- power-domains: phandle to the respective power domain.
+
+Required properties of an internal channel when:
+	- It is the only enabled channel of the bond (or)
+	- If it acts as primary among enabled bonds
+--------------------------------------------------------
+- pinctrl-0: pin control group to be used for this channel.
+- pinctrl-names: must be "default".
+- renesas,primary-bond: empty property indicating the channel acts as primary
+			among the bonded channels.
+- port: child port node corresponding to the data input, in accordance with
+	the video interface bindings defined in
+	Documentation/devicetree/bindings/media/video-interfaces.txt. The port
+	node must contain at least one endpoint.
+
+Optional endpoint property:
+---------------------------
+- sync-active: Indicates sync signal polarity, 0/1 for low/high respectively.
+	       This property maps to SYNCAC bit in the hardware manual. The
+	       default is 1 (active high).
+
+Example:
+--------
+
+(1) Both internal channels enabled:
+-----------------------------------
+
+When interfacing with a third party tuner device with two data pins as shown
+below.
+
++---------------------+                +---------------------+
+|                     |-----SCK------->|CLK                  |
+|       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
+|                     |-----SD0------->|D0                   |
+|                     |-----SD1------->|D1                   |
++---------------------+                +---------------------+
+
+	drif00: rif@e6f40000 {
+		compatible = "renesas,r8a7795-drif",
+			     "renesas,rcar-gen3-drif";
+		reg = <0 0xe6f40000 0 0x64>;
+		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 515>;
+		clock-names = "fck";
+		dmas = <&dmac1 0x20>, <&dmac2 0x20>;
+		dma-names = "rx", "rx";
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		renesas,bonding = <&drif01>;
+		renesas,primary-bond;
+		pinctrl-0 = <&drif0_pins>;
+		pinctrl-names = "default";
+		port {
+			drif0_ep: endpoint {
+			     remote-endpoint = <&tuner_ep>;
+			};
+		};
+	};
+
+	drif01: rif@e6f50000 {
+		compatible = "renesas,r8a7795-drif",
+			     "renesas,rcar-gen3-drif";
+		reg = <0 0xe6f50000 0 0x64>;
+		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 514>;
+		clock-names = "fck";
+		dmas = <&dmac1 0x22>, <&dmac2 0x22>;
+		dma-names = "rx", "rx";
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		renesas,bonding = <&drif00>;
+	};
+
+
+(2) Internal channel 1 alone is enabled:
+----------------------------------------
+
+When interfacing with a third party tuner device with one data pin as shown
+below.
+
++---------------------+                +---------------------+
+|                     |-----SCK------->|CLK                  |
+|       Master        |-----SS-------->|SYNC  DRIFn (slave)  |
+|                     |                |D0 (unused)          |
+|                     |-----SD-------->|D1                   |
++---------------------+                +---------------------+
+
+	drif00: rif@e6f40000 {
+		compatible = "renesas,r8a7795-drif",
+			     "renesas,rcar-gen3-drif";
+		reg = <0 0xe6f40000 0 0x64>;
+		interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 515>;
+		clock-names = "fck";
+		dmas = <&dmac1 0x20>, <&dmac2 0x20>;
+		dma-names = "rx", "rx";
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		renesas,bonding = <&drif01>;
+	};
+
+	drif01: rif@e6f50000 {
+		compatible = "renesas,r8a7795-drif",
+			     "renesas,rcar-gen3-drif";
+		reg = <0 0xe6f50000 0 0x64>;
+		interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 514>;
+		clock-names = "fck";
+		dmas = <&dmac1 0x22>, <&dmac2 0x22>;
+		dma-names = "rx", "rx";
+		power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
+		renesas,bonding = <&drif00>;
+		pinctrl-0 = <&drif0_pins>;
+		pinctrl-names = "default";
+		port {
+			drif0_ep: endpoint {
+			     remote-endpoint = <&tuner_ep>;
+			     sync-active = <0>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/renesas,fcp.txt b/Documentation/devicetree/bindings/media/renesas,fcp.txt
new file mode 100644
index 000000000..3ec91803b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,fcp.txt
@@ -0,0 +1,33 @@
+Renesas R-Car Frame Compression Processor (FCP)
+-----------------------------------------------
+
+The FCP is a companion module of video processing modules in the Renesas R-Car
+Gen3 SoCs. It provides data compression and decompression, data caching, and
+conversion of AXI transactions in order to reduce the memory bandwidth.
+
+There are three types of FCP: FCP for Codec (FCPC), FCP for VSP (FCPV) and FCP
+for FDP (FCPF). Their configuration and behaviour depend on the module they
+are paired with. These DT bindings currently support the FCPV and FCPF.
+
+ - compatible: Must be one or more of the following
+
+   - "renesas,fcpv" for generic compatible 'FCP for VSP'
+   - "renesas,fcpf" for generic compatible 'FCP for FDP'
+
+ - reg: the register base and size for the device registers
+ - clocks: Reference to the functional clock
+
+Optional properties:
+ - power-domains : power-domain property defined with a power domain specifier
+		   to respective power domain.
+
+
+Device node example
+-------------------
+
+	fcpvd1: fcp@fea2f000 {
+		compatible = "renesas,fcpv";
+		reg = <0 0xfea2f000 0 0x200>;
+		clocks = <&cpg CPG_MOD 602>;
+		power-domains = <&sysc R8A7795_PD_A3VP>;
+	};
diff --git a/Documentation/devicetree/bindings/media/renesas,fdp1.txt b/Documentation/devicetree/bindings/media/renesas,fdp1.txt
new file mode 100644
index 000000000..8dd1007bb
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,fdp1.txt
@@ -0,0 +1,37 @@
+Renesas R-Car Fine Display Processor (FDP1)
+-------------------------------------------
+
+The FDP1 is a de-interlacing module which converts interlaced video to
+progressive video. It is capable of performing pixel format conversion between
+YCbCr/YUV formats and RGB formats. Only YCbCr/YUV formats are supported as
+an input to the module.
+
+Required properties:
+
+ - compatible: must be "renesas,fdp1"
+ - reg: the register base and size for the device registers
+ - interrupts : interrupt specifier for the FDP1 instance
+ - clocks: reference to the functional clock
+
+Optional properties:
+
+ - power-domains: reference to the power domain that the FDP1 belongs to, if
+                  any.
+ - renesas,fcp: a phandle referencing the FCP that handles memory accesses
+                for the FDP1. Not needed on Gen2, mandatory on Gen3.
+
+Please refer to the binding documentation for the clock and/or power domain
+providers for more details.
+
+
+Device node example
+-------------------
+
+	fdp1@fe940000 {
+		compatible = "renesas,fdp1";
+		reg = <0 0xfe940000 0 0x2400>;
+		interrupts = <GIC_SPI 262 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 119>;
+		power-domains = <&sysc R8A7795_PD_A3VP>;
+		renesas,fcp = <&fcpf0>;
+	};
diff --git a/Documentation/devicetree/bindings/media/renesas,jpu.txt b/Documentation/devicetree/bindings/media/renesas,jpu.txt
new file mode 100644
index 000000000..d3436e519
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,jpu.txt
@@ -0,0 +1,25 @@
+* Renesas JPEG Processing Unit
+
+The JPEG processing unit (JPU) incorporates the JPEG codec with an encoding
+and decoding function conforming to the JPEG baseline process, so that the JPU
+can encode image data and decode JPEG data quickly.
+
+Required properties:
+- compatible: "renesas,jpu-<soctype>", "renesas,rcar-gen2-jpu" as fallback.
+	Examples with soctypes are:
+	  - "renesas,jpu-r8a7790" for R-Car H2
+	  - "renesas,jpu-r8a7791" for R-Car M2-W
+	  - "renesas,jpu-r8a7792" for R-Car V2H
+	  - "renesas,jpu-r8a7793" for R-Car M2-N
+
+  - reg: Base address and length of the registers block for the JPU.
+  - interrupts: JPU interrupt specifier.
+  - clocks: A phandle + clock-specifier pair for the JPU functional clock.
+
+Example: R8A7790 (R-Car H2) JPU node
+	jpeg-codec@fe980000 {
+		compatible = "renesas,jpu-r8a7790", "renesas,rcar-gen2-jpu";
+		reg = <0 0xfe980000 0 0x10300>;
+		interrupts = <0 272 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp1_clks R8A7790_CLK_JPU>;
+	};
diff --git a/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt
new file mode 100644
index 000000000..2d385b65b
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,rcar-csi2.txt
@@ -0,0 +1,101 @@
+Renesas R-Car MIPI CSI-2
+------------------------
+
+The R-Car CSI-2 receiver device provides MIPI CSI-2 capabilities for the
+Renesas R-Car family of devices. It is used in conjunction with the
+R-Car VIN module, which provides the video capture capabilities.
+
+Mandatory properties
+--------------------
+ - compatible: Must be one or more of the following
+   - "renesas,r8a7795-csi2" for the R8A7795 device.
+   - "renesas,r8a7796-csi2" for the R8A7796 device.
+   - "renesas,r8a77965-csi2" for the R8A77965 device.
+   - "renesas,r8a77970-csi2" for the R8A77970 device.
+
+ - reg: the register base and size for the device registers
+ - interrupts: the interrupt for the device
+ - clocks: reference to the parent clock
+
+The device node shall contain two 'port' child nodes according to the
+bindings defined in Documentation/devicetree/bindings/media/
+video-interfaces.txt. port@0 shall connect to the CSI-2 source. port@1
+shall connect to all the R-Car VIN modules that have a hardware
+connection to the CSI-2 receiver.
+
+- port@0- Video source (mandatory)
+	- endpoint@0 - sub-node describing the endpoint that is the video source
+
+- port@1 - VIN instances (optional)
+	- One endpoint sub-node for every R-Car VIN instance which is connected
+	  to the R-Car CSI-2 receiver.
+
+Example:
+
+	csi20: csi2@fea80000 {
+		compatible = "renesas,r8a7796-csi2";
+		reg = <0 0xfea80000 0 0x10000>;
+		interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 714>;
+		power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+		resets = <&cpg 714>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reg = <0>;
+
+				csi20_in: endpoint@0 {
+					reg = <0>;
+					clock-lanes = <0>;
+					data-lanes = <1>;
+					remote-endpoint = <&adv7482_txb>;
+				};
+			};
+
+			port@1 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				reg = <1>;
+
+				csi20vin0: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&vin0csi20>;
+				};
+				csi20vin1: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&vin1csi20>;
+				};
+				csi20vin2: endpoint@2 {
+					reg = <2>;
+					remote-endpoint = <&vin2csi20>;
+				};
+				csi20vin3: endpoint@3 {
+					reg = <3>;
+					remote-endpoint = <&vin3csi20>;
+				};
+				csi20vin4: endpoint@4 {
+					reg = <4>;
+					remote-endpoint = <&vin4csi20>;
+				};
+				csi20vin5: endpoint@5 {
+					reg = <5>;
+					remote-endpoint = <&vin5csi20>;
+				};
+				csi20vin6: endpoint@6 {
+					reg = <6>;
+					remote-endpoint = <&vin6csi20>;
+				};
+				csi20vin7: endpoint@7 {
+					reg = <7>;
+					remote-endpoint = <&vin7csi20>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/renesas,vsp1.txt b/Documentation/devicetree/bindings/media/renesas,vsp1.txt
new file mode 100644
index 000000000..16427017c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/renesas,vsp1.txt
@@ -0,0 +1,30 @@
+* Renesas VSP Video Processing Engine
+
+The VSP is a video processing engine that supports up-/down-scaling, alpha
+blending, color space conversion and various other image processing features.
+It can be found in the Renesas R-Car second generation SoCs.
+
+Required properties:
+
+  - compatible: Must contain one of the following values
+    - "renesas,vsp1" for the R-Car Gen2 VSP1
+    - "renesas,vsp2" for the R-Car Gen3 VSP2
+
+  - reg: Base address and length of the registers block for the VSP.
+  - interrupts: VSP interrupt specifier.
+  - clocks: A phandle + clock-specifier pair for the VSP functional clock.
+
+Optional properties:
+
+  - renesas,fcp: A phandle referencing the FCP that handles memory accesses
+                 for the VSP. Not needed on Gen2, mandatory on Gen3.
+
+
+Example: R8A7790 (R-Car H2) VSP1-S node
+
+	vsp@fe928000 {
+		compatible = "renesas,vsp1";
+		reg = <0 0xfe928000 0 0x8000>;
+		interrupts = <0 267 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&mstp1_clks R8A7790_CLK_VSP1_S>;
+	};
diff --git a/Documentation/devicetree/bindings/media/rockchip-rga.txt b/Documentation/devicetree/bindings/media/rockchip-rga.txt
new file mode 100644
index 000000000..fd5276abf
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/rockchip-rga.txt
@@ -0,0 +1,33 @@
+device-tree bindings for rockchip 2D raster graphic acceleration controller (RGA)
+
+RGA is a standalone 2D raster graphic acceleration unit. It accelerates 2D
+graphics operations, such as point/line drawing, image scaling, rotation,
+BitBLT, alpha blending and image blur/sharpness.
+
+Required properties:
+- compatible: value should be one of the following
+		"rockchip,rk3288-rga";
+		"rockchip,rk3399-rga";
+
+- interrupts: RGA interrupt specifier.
+
+- clocks: phandle to RGA sclk/hclk/aclk clocks
+
+- clock-names: should be "aclk", "hclk" and "sclk"
+
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: should be "core", "axi" and "ahb"
+
+Example:
+SoC-specific DT entry:
+	rga: rga@ff680000 {
+		compatible = "rockchip,rk3399-rga";
+		reg = <0xff680000 0x10000>;
+		interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru ACLK_RGA>, <&cru HCLK_RGA>, <&cru SCLK_RGA_CORE>;
+		clock-names = "aclk", "hclk", "sclk";
+
+		resets = <&cru SRST_RGA_CORE>, <&cru SRST_A_RGA>, <&cru SRST_H_RGA>;
+		reset-names = "core, "axi", "ahb";
+	};
diff --git a/Documentation/devicetree/bindings/media/s5p-cec.txt b/Documentation/devicetree/bindings/media/s5p-cec.txt
new file mode 100644
index 000000000..e847291d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/s5p-cec.txt
@@ -0,0 +1,36 @@
+* Samsung HDMI CEC driver
+
+The HDMI CEC module is present is Samsung SoCs and its purpose is to
+handle communication between HDMI connected devices over the CEC bus.
+
+Required properties:
+  - compatible : value should be following
+	"samsung,s5p-cec"
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : HDMI CEC interrupt number to the CPU.
+  - clocks : from common clock binding: handle to HDMI CEC clock.
+  - clock-names : from common clock binding: must contain "hdmicec",
+		  corresponding to entry in the clocks property.
+  - samsung,syscon-phandle - phandle to the PMU system controller
+  - hdmi-phandle - phandle to the HDMI controller, see also cec.txt.
+
+Optional:
+  - needs-hpd : if present the CEC support is only available when the HPD
+		is high. See cec.txt for more details.
+
+Example:
+
+hdmicec: cec@100b0000 {
+	compatible = "samsung,s5p-cec";
+	reg = <0x100B0000 0x200>;
+	interrupts = <0 114 0>;
+	clocks = <&clock CLK_HDMI_CEC>;
+	clock-names = "hdmicec";
+	samsung,syscon-phandle = <&pmu_system_controller>;
+	hdmi-phandle = <&hdmi>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&hdmi_cec>;
+};
diff --git a/Documentation/devicetree/bindings/media/s5p-mfc.txt b/Documentation/devicetree/bindings/media/s5p-mfc.txt
new file mode 100644
index 000000000..aa54c8159
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/s5p-mfc.txt
@@ -0,0 +1,76 @@
+* Samsung Multi Format Codec (MFC)
+
+Multi Format Codec (MFC) is the IP present in Samsung SoCs which
+supports high resolution decoding and encoding functionalities.
+The MFC device driver is a v4l2 driver which can encode/decode
+video raw/elementary streams and has support for all popular
+video codecs.
+
+Required properties:
+  - compatible : value should be either one among the following
+	(a) "samsung,mfc-v5" for MFC v5 present in Exynos4 SoCs
+	(b) "samsung,mfc-v6" for MFC v6 present in Exynos5 SoCs
+	(c) "samsung,mfc-v7" for MFC v7 present in Exynos5420 SoC
+	(d) "samsung,mfc-v8" for MFC v8 present in Exynos5800 SoC
+	(e) "samsung,exynos5433-mfc" for MFC v8 present in Exynos5433 SoC
+	(f) "samsung,mfc-v10" for MFC v10 present in Exynos7880 SoC
+
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+
+  - interrupts : MFC interrupt number to the CPU.
+  - clocks : from common clock binding: handle to mfc clock.
+  - clock-names : from common clock binding: must contain "mfc",
+		  corresponding to entry in the clocks property.
+
+Optional properties:
+  - power-domains : power-domain property defined with a phandle
+			   to respective power domain.
+  - memory-region : from reserved memory binding: phandles to two reserved
+	memory regions, first is for "left" mfc memory bus interfaces,
+	second if for the "right" mfc memory bus, used when no SYSMMU
+	support is available; used only by MFC v5 present in Exynos4 SoCs
+
+Obsolete properties:
+  - samsung,mfc-r, samsung,mfc-l : support removed, please use memory-region
+	property instead
+
+
+Example:
+SoC specific DT entry:
+
+mfc: codec@13400000 {
+	compatible = "samsung,mfc-v5";
+	reg = <0x13400000 0x10000>;
+	interrupts = <0 94 0>;
+	power-domains = <&pd_mfc>;
+	clocks = <&clock 273>;
+	clock-names = "mfc";
+};
+
+Reserved memory specific DT entry for given board (see reserved memory binding
+for more information):
+
+reserved-memory {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	ranges;
+
+	mfc_left: region@51000000 {
+		compatible = "shared-dma-pool";
+		no-map;
+		reg = <0x51000000 0x800000>;
+	};
+
+	mfc_right: region@43000000 {
+		compatible = "shared-dma-pool";
+		no-map;
+		reg = <0x43000000 0x800000>;
+	};
+};
+
+Board specific DT entry:
+
+codec@13400000 {
+	memory-region = <&mfc_left>, <&mfc_right>;
+};
diff --git a/Documentation/devicetree/bindings/media/samsung-fimc.txt b/Documentation/devicetree/bindings/media/samsung-fimc.txt
new file mode 100644
index 000000000..48c599dac
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/samsung-fimc.txt
@@ -0,0 +1,209 @@
+Samsung S5P/EXYNOS SoC Camera Subsystem (FIMC)
+----------------------------------------------
+
+The S5P/Exynos SoC Camera subsystem comprises of multiple sub-devices
+represented by separate device tree nodes. Currently this includes: FIMC (in
+the S5P SoCs series known as CAMIF), MIPI CSIS, FIMC-LITE and FIMC-IS (ISP).
+
+The sub-subdevices are defined as child nodes of the common 'camera' node which
+also includes common properties of the whole subsystem not really specific to
+any single sub-device, like common camera port pins or the CAMCLK clock outputs
+for external image sensors attached to an SoC.
+
+Common 'camera' node
+--------------------
+
+Required properties:
+
+- compatible: must be "samsung,fimc", "simple-bus"
+- clocks: list of clock specifiers, corresponding to entries in
+  the clock-names property;
+- clock-names : must contain "sclk_cam0", "sclk_cam1", "pxl_async0",
+  "pxl_async1" entries, matching entries in the clocks property.
+
+- #clock-cells: from the common clock bindings (../clock/clock-bindings.txt),
+  must be 1. A clock provider is associated with the 'camera' node and it should
+  be referenced by external sensors that use clocks provided by the SoC on
+  CAM_*_CLKOUT pins. The clock specifier cell stores an index of a clock.
+  The indices are 0, 1 for CAM_A_CLKOUT, CAM_B_CLKOUT clocks respectively.
+
+- clock-output-names: from the common clock bindings, should contain names of
+  clocks registered by the camera subsystem corresponding to CAM_A_CLKOUT,
+  CAM_B_CLKOUT output clocks respectively.
+
+The pinctrl bindings defined in ../pinctrl/pinctrl-bindings.txt must be used
+to define a required pinctrl state named "default" and optional pinctrl states:
+"idle", "active-a", active-b". These optional states can be used to switch the
+camera port pinmux at runtime. The "idle" state should configure both the camera
+ports A and B into high impedance state, especially the CAMCLK clock output
+should be inactive. For the "active-a" state the camera port A must be activated
+and the port B deactivated and for the state "active-b" it should be the other
+way around.
+
+The 'camera' node must include at least one 'fimc' child node.
+
+
+'fimc' device nodes
+-------------------
+
+Required properties:
+
+- compatible: "samsung,s5pv210-fimc" for S5PV210, "samsung,exynos4210-fimc"
+  for Exynos4210 and "samsung,exynos4212-fimc" for Exynos4x12 SoCs;
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain FIMC interrupt;
+- clocks: list of clock specifiers, must contain an entry for each required
+  entry in clock-names;
+- clock-names: must contain "fimc", "sclk_fimc" entries.
+- samsung,pix-limits: an array of maximum supported image sizes in pixels, for
+  details refer to Table 2-1 in the S5PV210 SoC User Manual; The meaning of
+  each cell is as follows:
+  0 - scaler input horizontal size,
+  1 - input horizontal size for the scaler bypassed,
+  2 - REAL_WIDTH without input rotation,
+  3 - REAL_HEIGHT with input rotation,
+- samsung,sysreg: a phandle to the SYSREG node.
+
+Each FIMC device should have an alias in the aliases node, in the form of
+fimc<n>, where <n> is an integer specifying the IP block instance.
+
+Optional properties:
+
+- clock-frequency: maximum FIMC local clock (LCLK) frequency;
+- samsung,min-pix-sizes: an array specyfing minimum image size in pixels at
+  the FIMC input and output DMA, in the first and second cell respectively.
+  Default value when this property is not present is <16 16>;
+- samsung,min-pix-alignment: minimum supported image height alignment (first
+  cell) and the horizontal image offset (second cell). The values are in pixels
+  and default to <2 1> when this property is not present;
+- samsung,mainscaler-ext: a boolean property indicating whether the FIMC IP
+  supports extended image size and has CIEXTEN register;
+- samsung,rotators: a bitmask specifying whether this IP has the input and
+  the output rotator. Bits 4 and 0 correspond to input and output rotator
+  respectively. If a rotator is present its corresponding bit should be set.
+  Default value when this property is not specified is 0x11.
+- samsung,cam-if: a bolean property indicating whether the IP block includes
+  the camera input interface.
+- samsung,isp-wb: this property must be present if the IP block has the ISP
+  writeback input.
+- samsung,lcd-wb: this property must be present if the IP block has the LCD
+  writeback input.
+
+
+'parallel-ports' node
+---------------------
+
+This node should contain child 'port' nodes specifying active parallel video
+input ports. It includes camera A and camera B inputs. 'reg' property in the
+port nodes specifies data input - 0, 1 indicates input A, B respectively.
+
+Optional properties
+
+- samsung,camclk-out (deprecated) : specifies clock output for remote sensor,
+  0 - CAM_A_CLKOUT, 1 - CAM_B_CLKOUT;
+
+Image sensor nodes
+------------------
+
+The sensor device nodes should be added to their control bus controller (e.g.
+I2C0) nodes and linked to a port node in the csis or the parallel-ports node,
+using the common video interfaces bindings, defined in video-interfaces.txt.
+
+Example:
+
+	aliases {
+		fimc0 = &fimc_0;
+	};
+
+	/* Parallel bus IF sensor */
+	i2c_0: i2c@13860000 {
+		s5k6aa: sensor@3c {
+			compatible = "samsung,s5k6aafx";
+			reg = <0x3c>;
+			vddio-supply = <...>;
+
+			clock-frequency = <24000000>;
+			clocks = <&camera 1>;
+			clock-names = "mclk";
+
+			port {
+				s5k6aa_ep: endpoint {
+					remote-endpoint = <&fimc0_ep>;
+					bus-width = <8>;
+					hsync-active = <0>;
+					vsync-active = <1>;
+					pclk-sample = <1>;
+				};
+			};
+		};
+
+		/* MIPI CSI-2 bus IF sensor */
+		s5c73m3: sensor@1a {
+			compatible = "samsung,s5c73m3";
+			reg = <0x1a>;
+			vddio-supply = <...>;
+
+			clock-frequency = <24000000>;
+			clocks = <&camera 0>;
+			clock-names = "mclk";
+
+			port {
+				s5c73m3_1: endpoint {
+					data-lanes = <1 2 3 4>;
+					remote-endpoint = <&csis0_ep>;
+				};
+			};
+		};
+	};
+
+	camera {
+		compatible = "samsung,fimc", "simple-bus";
+		clocks = <&clock 132>, <&clock 133>, <&clock 351>,
+			 <&clock 352>;
+		clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0",
+			      "pxl_async1";
+		#clock-cells = <1>;
+		clock-output-names = "cam_a_clkout", "cam_b_clkout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&cam_port_a_clk_active>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		/* parallel camera ports */
+		parallel-ports {
+			/* camera A input */
+			port@0 {
+				reg = <0>;
+				fimc0_ep: endpoint {
+					remote-endpoint = <&s5k6aa_ep>;
+					bus-width = <8>;
+					hsync-active = <0>;
+					vsync-active = <1>;
+					pclk-sample = <1>;
+				};
+			};
+		};
+
+		fimc_0: fimc@11800000 {
+			compatible = "samsung,exynos4210-fimc";
+			reg = <0x11800000 0x1000>;
+			interrupts = <0 85 0>;
+		};
+
+		csis_0: csis@11880000 {
+			compatible = "samsung,exynos4210-csis";
+			reg = <0x11880000 0x1000>;
+			interrupts = <0 78 0>;
+			/* camera C input */
+			port@3 {
+				reg = <3>;
+				csis0_ep: endpoint {
+					remote-endpoint = <&s5c73m3_ep>;
+					data-lanes = <1 2 3 4>;
+					samsung,csis-hs-settle = <12>;
+				};
+			};
+		};
+	};
+
+The MIPI-CSIS device binding is defined in samsung-mipi-csis.txt.
diff --git a/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt
new file mode 100644
index 000000000..be45f0b1a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/samsung-mipi-csis.txt
@@ -0,0 +1,81 @@
+Samsung S5P/EXYNOS SoC series MIPI CSI-2 receiver (MIPI CSIS)
+-------------------------------------------------------------
+
+Required properties:
+
+- compatible	  : "samsung,s5pv210-csis" for S5PV210 (S5PC110),
+		    "samsung,exynos4210-csis" for Exynos4210 (S5PC210),
+		    "samsung,exynos4212-csis" for Exynos4212/Exynos4412,
+		    "samsung,exynos5250-csis" for Exynos5250;
+- reg		  : offset and length of the register set for the device;
+- interrupts      : should contain MIPI CSIS interrupt; the format of the
+		    interrupt specifier depends on the interrupt controller;
+- bus-width	  : maximum number of data lanes supported (SoC specific);
+- vddio-supply    : MIPI CSIS I/O and PLL voltage supply (e.g. 1.8V);
+- vddcore-supply  : MIPI CSIS Core voltage supply (e.g. 1.1V);
+- clocks	  : list of clock specifiers, corresponding to entries in
+		    clock-names property;
+- clock-names	  : must contain "csis", "sclk_csis" entries, matching entries
+		    in the clocks property.
+
+Optional properties:
+
+- clock-frequency : The IP's main (system bus) clock frequency in Hz, default
+		    value when this property is not specified is 166 MHz;
+- samsung,csis-wclk : CSI-2 wrapper clock selection. If this property is present
+		    external clock from CMU will be used, or the bus clock if
+		    if it's not specified.
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+media/video-interfaces.txt. The following are properties specific to those nodes.
+
+port node
+---------
+
+- reg		  : (required) must be 3 for camera C input (CSIS0) or 4 for
+		    camera D input (CSIS1);
+
+endpoint node
+-------------
+
+- data-lanes	  : (required) an array specifying active physical MIPI-CSI2
+		    data input lanes and their mapping to logical lanes; the
+		    array's content is unused, only its length is meaningful;
+
+- samsung,csis-hs-settle : (optional) differential receiver (HS-RX) settle time;
+
+
+Example:
+
+	reg0: regulator@0 {
+	};
+
+	reg1: regulator@1 {
+	};
+
+/* SoC properties */
+
+	csis_0: csis@11880000 {
+		compatible = "samsung,exynos4210-csis";
+		reg = <0x11880000 0x1000>;
+		interrupts = <0 78 0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+/* Board properties */
+
+	csis_0: csis@11880000 {
+		clock-frequency = <166000000>;
+		vddio-supply = <&reg0>;
+		vddcore-supply = <&reg1>;
+		port {
+			reg = <3>; /* 3 - CSIS0, 4 - CSIS1 */
+			csis0_ep: endpoint {
+				remote-endpoint = <...>;
+				data-lanes = <1>, <2>;
+				samsung,csis-hs-settle = <12>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt
new file mode 100644
index 000000000..21f31fdf5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/samsung-s5c73m3.txt
@@ -0,0 +1,97 @@
+Samsung S5C73M3 8Mp camera ISP
+------------------------------
+
+The S5C73M3 camera ISP supports MIPI CSI-2 and parallel (ITU-R BT.656) video
+data busses. The I2C bus is the main control bus and additionally the SPI bus
+is used, mostly for transferring the firmware to and from the device. Two
+slave device nodes corresponding to these control bus interfaces are required
+and should be placed under respective bus controller nodes.
+
+I2C slave device node
+---------------------
+
+Required properties:
+
+- compatible	    : "samsung,s5c73m3";
+- reg		    : I2C slave address of the sensor;
+- vdd-int-supply    : digital power supply (1.2V);
+- vdda-supply	    : analog power supply (1.2V);
+- vdd-reg-supply    : regulator input power supply (2.8V);
+- vddio-host-supply : host I/O power supply (1.8V to 2.8V);
+- vddio-cis-supply  : CIS I/O power supply (1.2V to 1.8V);
+- vdd-af-supply     : lens power supply (2.8V);
+- xshutdown-gpios   : specifier of GPIO connected to the XSHUTDOWN pin;
+- standby-gpios     : specifier of GPIO connected to the STANDBY pin;
+- clocks	    : should contain list of phandle and clock specifier pairs
+		      according to common clock bindings for the clocks described
+		      in the clock-names property;
+- clock-names	    : should contain "cis_extclk" entry for the CIS_EXTCLK clock;
+
+Optional properties:
+
+- clock-frequency   : the frequency at which the "cis_extclk" clock should be
+		      configured to operate, in Hz; if this property is not
+		      specified default 24 MHz value will be used.
+
+The common video interfaces bindings (see video-interfaces.txt) should be used
+to specify link from the S5C73M3 to an external image data receiver. The S5C73M3
+device node should contain one 'port' child node with an 'endpoint' subnode for
+this purpose. The data link from a raw image sensor to the S5C73M3 can be
+similarly specified, but it is optional since the S5C73M3 ISP and a raw image
+sensor are usually inseparable and form a hybrid module.
+
+Following properties are valid for the endpoint node(s):
+
+endpoint subnode
+----------------
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+  video-interfaces.txt. This sensor doesn't support data lane remapping
+  and physical lane indexes in subsequent elements of the array should
+  be only consecutive ascending values.
+
+SPI device node
+---------------
+
+Required properties:
+
+- compatible	    : "samsung,s5c73m3";
+
+For more details see description of the SPI busses bindings
+(../spi/spi-bus.txt) and bindings of a specific bus controller.
+
+Example:
+
+i2c@138a000000 {
+	...
+	s5c73m3@3c {
+		compatible = "samsung,s5c73m3";
+		reg = <0x3c>;
+		vdd-int-supply = <&buck9_reg>;
+		vdda-supply = <&ldo17_reg>;
+		vdd-reg-supply = <&cam_io_reg>;
+		vddio-host-supply = <&ldo18_reg>;
+		vddio-cis-supply = <&ldo9_reg>;
+		vdd-af-supply = <&cam_af_reg>;
+		clock-frequency = <24000000>;
+		clocks = <&clk 0>;
+		clock-names = "cis_extclk";
+		reset-gpios = <&gpf1 3 1>;
+		standby-gpios = <&gpm0 1 1>;
+		port {
+			s5c73m3_ep: endpoint {
+				remote-endpoint = <&csis0_ep>;
+				data-lanes = <1 2 3 4>;
+			};
+		};
+	};
+};
+
+spi@1392000 {
+	...
+	s5c73m3_spi: s5c73m3@0 {
+		compatible = "samsung,s5c73m3";
+		reg = <0>;
+		...
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/samsung-s5k5baf.txt b/Documentation/devicetree/bindings/media/samsung-s5k5baf.txt
new file mode 100644
index 000000000..1f51e0439
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/samsung-s5k5baf.txt
@@ -0,0 +1,58 @@
+Samsung S5K5BAF UXGA 1/5" 2M CMOS Image Sensor with embedded SoC ISP
+--------------------------------------------------------------------
+
+Required properties:
+
+- compatible	  : "samsung,s5k5baf";
+- reg		  : I2C slave address of the sensor;
+- vdda-supply	  : analog power supply 2.8V (2.6V to 3.0V);
+- vddreg-supply	  : regulator input power supply 1.8V (1.7V to 1.9V)
+		    or 2.8V (2.6V to 3.0);
+- vddio-supply	  : I/O power supply 1.8V (1.65V to 1.95V)
+		    or 2.8V (2.5V to 3.1V);
+- stbyn-gpios	  : GPIO connected to STDBYN pin;
+- rstn-gpios	  : GPIO connected to RSTN pin;
+- clocks	  : list of phandle and clock specifier pairs
+		    according to common clock bindings for the
+		    clocks described in clock-names;
+- clock-names	  : should include "mclk" for the sensor's master clock;
+
+Optional properties:
+
+- clock-frequency : the frequency at which the "mclk" clock should be
+		    configured to operate, in Hz; if this property is not
+		    specified default 24 MHz value will be used.
+
+The device node should contain one 'port' child node with one child 'endpoint'
+node, according to the bindings defined in Documentation/devicetree/bindings/
+media/video-interfaces.txt. The following are properties specific to those
+nodes.
+
+endpoint node
+-------------
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+	       video-interfaces.txt. If present it should be <1> - the device
+	       supports only one data lane without re-mapping.
+
+Example:
+
+s5k5bafx@2d {
+	compatible = "samsung,s5k5baf";
+	reg = <0x2d>;
+	vdda-supply = <&cam_io_en_reg>;
+	vddreg-supply = <&vt_core_15v_reg>;
+	vddio-supply = <&vtcam_reg>;
+	stbyn-gpios = <&gpl2 0 1>;
+	rstn-gpios = <&gpl2 1 1>;
+	clock-names = "mclk";
+	clocks = <&clock_cam 0>;
+	clock-frequency = <24000000>;
+
+	port {
+		s5k5bafx_ep: endpoint {
+			remote-endpoint = <&csis1_ep>;
+			data-lanes = <1>;
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
new file mode 100644
index 000000000..cce01e82f
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/samsung-s5k6a3.txt
@@ -0,0 +1,33 @@
+Samsung S5K6A3(YX) raw image sensor
+---------------------------------
+
+S5K6A3(YX) is a raw image sensor with MIPI CSI-2 and CCP2 image data interfaces
+and CCI (I2C compatible) control bus.
+
+Required properties:
+
+- compatible	: "samsung,s5k6a3";
+- reg		: I2C slave address of the sensor;
+- svdda-supply	: core voltage supply;
+- svddio-supply	: I/O voltage supply;
+- afvdd-supply	: AF (actuator) voltage supply;
+- gpios		: specifier of a GPIO connected to the RESET pin;
+- clocks	: should contain list of phandle and clock specifier pairs
+		  according to common clock bindings for the clocks described
+		  in the clock-names property;
+- clock-names	: should contain "extclk" entry for the sensor's EXTCLK clock;
+
+Optional properties:
+
+- clock-frequency : the frequency at which the "extclk" clock should be
+		    configured to operate, in Hz; if this property is not
+		    specified default 24 MHz value will be used.
+
+The common video interfaces bindings (see video-interfaces.txt) should be
+used to specify link to the image data receiver. The S5K6A3(YX) device
+node should contain one 'port' child node with an 'endpoint' subnode.
+
+Following properties are valid for the endpoint node:
+
+- data-lanes : (optional) specifies MIPI CSI-2 data lanes as covered in
+  video-interfaces.txt.  The sensor supports only one data lane.
diff --git a/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt
new file mode 100644
index 000000000..cfa4ffada
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/sh_mobile_ceu.txt
@@ -0,0 +1,17 @@
+Bindings, specific for the sh_mobile_ceu_camera.c driver:
+ - compatible: Should be "renesas,sh-mobile-ceu"
+ - reg: register base and size
+ - interrupts: the interrupt number
+ - renesas,max-width: maximum image width, supported on this SoC
+ - renesas,max-height: maximum image height, supported on this SoC
+
+Example:
+
+ceu0: ceu@fe910000 {
+	compatible = "renesas,sh-mobile-ceu";
+	reg = <0xfe910000 0xa0>;
+	interrupt-parent = <&intcs>;
+	interrupts = <0x880>;
+	renesas,max-width = <8188>;
+	renesas,max-height = <8188>;
+};
diff --git a/Documentation/devicetree/bindings/media/si4713.txt b/Documentation/devicetree/bindings/media/si4713.txt
new file mode 100644
index 000000000..5ee5552d3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/si4713.txt
@@ -0,0 +1,30 @@
+* Silicon Labs FM Radio transmitter
+
+The Silicon Labs Si4713 is an FM radio transmitter with receive power scan
+supporting 76-108 MHz. It includes an RDS encoder and has both, a stereo-analog
+and a digital interface, which supports I2S, left-justified and a custom
+DSP-mode format. It is programmable through an I2C interface.
+
+Required Properties:
+- compatible: Should contain "silabs,si4713"
+- reg: the I2C address of the device
+
+Optional Properties:
+- interrupts-extended: Interrupt specifier for the chips interrupt
+- reset-gpios: GPIO specifier for the chips reset line
+- vdd-supply: phandle for Vdd regulator
+- vio-supply: phandle for Vio regulator
+
+Example:
+
+&i2c2 {
+        fmtx: si4713@63 {
+                compatible = "silabs,si4713";
+                reg = <0x63>;
+
+                interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
+                reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
+                vio-supply = <&vio>;
+                vdd-supply = <&vaux1>;
+        };
+};
diff --git a/Documentation/devicetree/bindings/media/spi/sony-cxd2880.txt b/Documentation/devicetree/bindings/media/spi/sony-cxd2880.txt
new file mode 100644
index 000000000..fc5aa263a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/spi/sony-cxd2880.txt
@@ -0,0 +1,14 @@
+Sony CXD2880 DVB-T2/T tuner + demodulator driver SPI adapter
+
+Required properties:
+- compatible: Should be "sony,cxd2880".
+- reg: SPI chip select number for the device.
+- spi-max-frequency: Maximum bus speed, should be set to <55000000> (55MHz).
+
+Example:
+
+cxd2880@0 {
+	compatible = "sony,cxd2880";
+	reg = <0>; /* CE0 */
+	spi-max-frequency = <55000000>; /* 55MHz */
+};
diff --git a/Documentation/devicetree/bindings/media/st,st-delta.txt b/Documentation/devicetree/bindings/media/st,st-delta.txt
new file mode 100644
index 000000000..a538ab30a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,st-delta.txt
@@ -0,0 +1,17 @@
+* STMicroelectronics DELTA multi-format video decoder
+
+Required properties:
+- compatible: should be "st,st-delta".
+- clocks: from common clock binding: handle hardware IP needed clocks, the
+  number of clocks may depend on the SoC type.
+  See ../clock/clock-bindings.txt for details.
+- clock-names: names of the clocks listed in clocks property in the same order.
+
+Example:
+	delta0 {
+		compatible = "st,st-delta";
+		clock-names = "delta", "delta-st231", "delta-flash-promip";
+		clocks = <&clk_s_c0_flexgen CLK_VID_DMU>,
+			 <&clk_s_c0_flexgen CLK_ST231_DMU>,
+			 <&clk_s_c0_flexgen CLK_FLASH_PROMIP>;
+	};
diff --git a/Documentation/devicetree/bindings/media/st,st-hva.txt b/Documentation/devicetree/bindings/media/st,st-hva.txt
new file mode 100644
index 000000000..0d76174a1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,st-hva.txt
@@ -0,0 +1,24 @@
+st-hva: multi-format video encoder for STMicroelectronics SoC.
+
+Required properties:
+- compatible: should be "st,st-hva".
+- reg: HVA physical address location and length, esram address location and
+  length.
+- reg-names: names of the registers listed in registers property in the same
+  order.
+- interrupts: HVA interrupt number.
+- clocks: from common clock binding: handle hardware IP needed clocks, the
+  number of clocks may depend on the SoC type.
+  See ../clock/clock-bindings.txt for details.
+- clock-names: names of the clocks listed in clocks property in the same order.
+
+Example:
+	hva@8c85000{
+		compatible = "st,st-hva";
+		reg = <0x8c85000 0x400>, <0x6000000 0x40000>;
+		reg-names = "hva_registers", "hva_esram";
+		interrupts = <GIC_SPI 58 IRQ_TYPE_NONE>,
+			     <GIC_SPI 59 IRQ_TYPE_NONE>;
+		clock-names = "clk_hva";
+		clocks = <&clk_s_c0_flexgen CLK_HVA>;
+	};
diff --git a/Documentation/devicetree/bindings/media/st,stih4xx.txt b/Documentation/devicetree/bindings/media/st,stih4xx.txt
new file mode 100644
index 000000000..df655cd3a
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,stih4xx.txt
@@ -0,0 +1,32 @@
+STMicroelectronics stih4xx platforms
+
+bdisp: 2D blitter for STMicroelectronics SoC.
+
+Required properties:
+- compatible: should be "st,stih407-bdisp".
+- reg: BDISP physical address location and length.
+- interrupts: BDISP interrupt number.
+- clocks: from common clock binding: handle hardware IP needed clocks, the
+  number of clocks may depend on the SoC type.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: names of the clocks listed in clocks property in the same order.
+
+Example:
+
+	bdisp0:bdisp@9f10000 {
+		compatible = "st,stih407-bdisp";
+		reg = <0x9f10000 0x1000>;
+		interrupts = <GIC_SPI 38 IRQ_TYPE_NONE>;
+		clock-names = "bdisp";
+		clocks = <&clk_s_c0_flexgen CLK_IC_BDISP_0>;
+	};
+
+Aliases:
+Each BDISP should have a numbered alias in the aliases node, in the form of
+bdispN, N = 0 or 1.
+
+Example:
+
+	aliases {
+		bdisp0 = &bdisp0;
+	};
diff --git a/Documentation/devicetree/bindings/media/st,stm32-cec.txt b/Documentation/devicetree/bindings/media/st,stm32-cec.txt
new file mode 100644
index 000000000..6be2381c1
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,stm32-cec.txt
@@ -0,0 +1,19 @@
+STMicroelectronics STM32 CEC driver
+
+Required properties:
+ - compatible : value should be "st,stm32-cec"
+ - reg : Physical base address of the IP registers and length of memory
+	 mapped region.
+ - clocks : from common clock binding: handle to CEC clocks
+ - clock-names : from common clock binding: must be "cec" and "hdmi-cec".
+ - interrupts : CEC interrupt number to the CPU.
+
+Example for stm32f746:
+
+cec: cec@40006c00 {
+	compatible = "st,stm32-cec";
+	reg = <0x40006C00 0x400>;
+	interrupts = <94>;
+	clocks = <&rcc 0 STM32F7_APB1_CLOCK(CEC)>, <&rcc 1 CLK_HDMI_CEC>;
+	clock-names = "cec", "hdmi-cec";
+};
diff --git a/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
new file mode 100644
index 000000000..249790a93
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st,stm32-dcmi.txt
@@ -0,0 +1,45 @@
+STMicroelectronics STM32 Digital Camera Memory Interface (DCMI)
+
+Required properties:
+- compatible: "st,stm32-dcmi"
+- reg: physical base address and length of the registers set for the device
+- interrupts: should contain IRQ line for the DCMI
+- resets: reference to a reset controller,
+          see Documentation/devicetree/bindings/reset/st,stm32-rcc.txt
+- clocks: list of clock specifiers, corresponding to entries in
+          the clock-names property
+- clock-names: must contain "mclk", which is the DCMI peripherial clock
+- pinctrl: the pincontrol settings to configure muxing properly
+           for pins that connect to DCMI device.
+           See Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.txt.
+- dmas: phandle to DMA controller node,
+        see Documentation/devicetree/bindings/dma/stm32-dma.txt
+- dma-names: must contain "tx", which is the transmit channel from DCMI to DMA
+
+DCMI supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+
+	dcmi: dcmi@50050000 {
+		compatible = "st,stm32-dcmi";
+		reg = <0x50050000 0x400>;
+		interrupts = <78>;
+		resets = <&rcc STM32F4_AHB2_RESET(DCMI)>;
+		clocks = <&rcc 0 STM32F4_AHB2_CLOCK(DCMI)>;
+		clock-names = "mclk";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dcmi_pins>;
+		dmas = <&dma2 1 1 0x414 0x3>;
+		dma-names = "tx";
+		port {
+			dcmi_0: endpoint {
+				remote-endpoint = <...>;
+				bus-width = <8>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				pclk-sample = <1>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/st-rc.txt b/Documentation/devicetree/bindings/media/st-rc.txt
new file mode 100644
index 000000000..05c432d08
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/st-rc.txt
@@ -0,0 +1,29 @@
+Device-Tree bindings for ST IRB IP
+
+Required properties:
+	- compatible: Should contain "st,comms-irb".
+	- reg: Base physical address of the controller and length of memory
+	  mapped region.
+	- interrupts: interrupt-specifier for the sole interrupt generated by
+	  the device. The interrupt specifier format depends on the interrupt
+	  controller parent.
+	- rx-mode: can be "infrared" or "uhf". This property specifies the L1
+	  protocol used for receiving remote control signals. rx-mode should
+	  be present iff the rx pins are wired up.
+	- tx-mode: should be "infrared". This property specifies the L1
+	  protocol used for transmitting remote control signals. tx-mode should
+	  be present iff the tx pins are wired up.
+
+Optional properties:
+	- pinctrl-names, pinctrl-0: the pincontrol settings to configure muxing
+	  properly for IRB pins.
+	- clocks : phandle with clock-specifier pair for IRB.
+
+Example node:
+
+	rc: rc@fe518000 {
+		compatible	= "st,comms-irb";
+		reg		= <0xfe518000 0x234>;
+		interrupts	= <0 203 0>;
+		rx-mode		= "infrared";
+	};
diff --git a/Documentation/devicetree/bindings/media/stih-cec.txt b/Documentation/devicetree/bindings/media/stih-cec.txt
new file mode 100644
index 000000000..ece0832fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/stih-cec.txt
@@ -0,0 +1,27 @@
+STMicroelectronics STIH4xx HDMI CEC driver
+
+Required properties:
+ - compatible : value should be "st,stih-cec"
+ - reg : Physical base address of the IP registers and length of memory
+	 mapped region.
+ - clocks : from common clock binding: handle to HDMI CEC clock
+ - interrupts : HDMI CEC interrupt number to the CPU.
+ - pinctrl-names: Contains only one value - "default"
+ - pinctrl-0: Specifies the pin control groups used for CEC hardware.
+ - resets: Reference to a reset controller
+ - hdmi-phandle: Phandle to the HDMI controller, see also cec.txt.
+
+Example for STIH407:
+
+sti-cec@94a087c {
+	compatible = "st,stih-cec";
+	reg = <0x94a087c 0x64>;
+	clocks = <&clk_sysin>;
+	clock-names = "cec-clk";
+	interrupts = <GIC_SPI 140 IRQ_TYPE_NONE>;
+	interrupt-names = "cec-irq";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_cec0_default>;
+	resets = <&softreset STIH407_LPM_SOFTRESET>;
+	hdmi-phandle = <&hdmi>;
+};
diff --git a/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
new file mode 100644
index 000000000..880d4d70c
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/stih407-c8sectpfe.txt
@@ -0,0 +1,88 @@
+STMicroelectronics STi c8sectpfe binding
+============================================
+
+This document describes the c8sectpfe device bindings that is used to get transport
+stream data into the SoC on the TS pins, and into DDR for further processing.
+
+It is typically used in conjunction with one or more demodulator and tuner devices
+which converts from the RF to digital domain. Demodulators and tuners are usually
+located on an external DVB frontend card connected to SoC TS input pins.
+
+Currently 7 TS input (tsin) channels are supported on the stih407 family SoC.
+
+Required properties (controller (parent) node):
+- compatible	: Should be "stih407-c8sectpfe"
+
+- reg		: Address and length of register sets for each device in
+		  "reg-names"
+
+- reg-names	: The names of the register addresses corresponding to the
+		  registers filled in "reg":
+			- c8sectpfe: c8sectpfe registers
+			- c8sectpfe-ram: c8sectpfe internal sram
+
+- clocks	: phandle list of c8sectpfe clocks
+- clock-names	: should be "c8sectpfe"
+See: Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+- pinctrl-names	: a pinctrl state named tsin%d-serial or tsin%d-parallel (where %d is tsin-num)
+		   must be defined for each tsin child node.
+- pinctrl-0	: phandle referencing pin configuration for this tsin configuration
+See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+
+Required properties (tsin (child) node):
+
+- tsin-num	: tsin id of the InputBlock (must be between 0 to 6)
+- i2c-bus	: phandle to the I2C bus DT node which the demodulators & tuners on this tsin channel are connected.
+- reset-gpios	: reset gpio for this tsin channel.
+
+Optional properties (tsin (child) node):
+
+- invert-ts-clk		: Bool property to control sense of ts input clock (data stored on falling edge of clk).
+- serial-not-parallel	: Bool property to configure input bus width (serial on ts_data<7>).
+- async-not-sync	: Bool property to control if data is received in asynchronous mode
+			   (all bits/bytes with ts_valid or ts_packet asserted are valid).
+
+- dvb-card		: Describes the NIM card connected to this tsin channel.
+
+Example:
+
+/* stih410 SoC b2120 + b2004a + stv0367-pll(NIMB) + stv0367-tda18212 (NIMA) DT example) */
+
+	c8sectpfe@8a20000 {
+		compatible = "st,stih407-c8sectpfe";
+		reg = <0x08a20000 0x10000>, <0x08a00000 0x4000>;
+		reg-names = "stfe", "stfe-ram";
+		interrupts = <GIC_SPI 34 IRQ_TYPE_NONE>, <GIC_SPI 35 IRQ_TYPE_NONE>;
+		interrupt-names = "stfe-error-irq", "stfe-idle-irq";
+		pinctrl-0	= <&pinctrl_tsin0_serial>;
+		pinctrl-1	= <&pinctrl_tsin0_parallel>;
+		pinctrl-2	= <&pinctrl_tsin3_serial>;
+		pinctrl-3	= <&pinctrl_tsin4_serial_alt3>;
+		pinctrl-4	= <&pinctrl_tsin5_serial_alt1>;
+		pinctrl-names	= "tsin0-serial",
+				  "tsin0-parallel",
+				  "tsin3-serial",
+				  "tsin4-serial",
+				  "tsin5-serial";
+		clocks = <&clk_s_c0_flexgen CLK_PROC_STFE>;
+		clock-names = "c8sectpfe";
+
+		/* tsin0 is TSA on NIMA */
+		tsin0: port@0 {
+			tsin-num		= <0>;
+			serial-not-parallel;
+			i2c-bus			= <&ssc2>;
+			reset-gpios		= <&pio15 4 GPIO_ACTIVE_HIGH>;
+			dvb-card		= <STV0367_TDA18212_NIMA_1>;
+		};
+
+		tsin3: port@3 {
+			tsin-num		= <3>;
+			serial-not-parallel;
+			i2c-bus			= <&ssc3>;
+			reset-gpios		= <&pio15 7 GPIO_ACTIVE_HIGH>;
+			dvb-card		= <STV0367_TDA18212_NIMB_1>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/sunxi-ir.txt b/Documentation/devicetree/bindings/media/sunxi-ir.txt
new file mode 100644
index 000000000..278098987
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/sunxi-ir.txt
@@ -0,0 +1,28 @@
+Device-Tree bindings for SUNXI IR controller found in sunXi SoC family
+
+Required properties:
+- compatible	    : "allwinner,sun4i-a10-ir" or "allwinner,sun5i-a13-ir"
+- clocks	    : list of clock specifiers, corresponding to
+		      entries in clock-names property;
+- clock-names	    : should contain "apb" and "ir" entries;
+- interrupts	    : should contain IR IRQ number;
+- reg		    : should contain IO map address for IR.
+
+Optional properties:
+- linux,rc-map-name: see rc.txt file in the same directory.
+- resets : phandle + reset specifier pair
+- clock-frequency  : IR Receiver clock frequency, in Hertz. Defaults to 8 MHz
+		     if missing.
+
+Example:
+
+ir0: ir@1c21800 {
+	compatible = "allwinner,sun4i-a10-ir";
+	clocks = <&apb0_gates 6>, <&ir0_clk>;
+	clock-names = "apb", "ir";
+	clock-frequency = <3000000>;
+	resets = <&apb0_rst 1>;
+	interrupts = <0 5 1>;
+	reg = <0x01C21800 0x40>;
+	linux,rc-map-name = "rc-rc6-mce";
+};
diff --git a/Documentation/devicetree/bindings/media/tango-ir.txt b/Documentation/devicetree/bindings/media/tango-ir.txt
new file mode 100644
index 000000000..a9f00c2bf
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/tango-ir.txt
@@ -0,0 +1,21 @@
+Sigma Designs Tango IR NEC/RC-5/RC-6 decoder (SMP86xx and SMP87xx)
+
+Required properties:
+
+- compatible: "sigma,smp8642-ir"
+- reg: address/size of NEC+RC5 area, address/size of RC6 area
+- interrupts: spec for IR IRQ
+- clocks: spec for IR clock (typically the crystal oscillator)
+
+Optional properties:
+
+- linux,rc-map-name: see Documentation/devicetree/bindings/media/rc.txt
+
+Example:
+
+	ir@10518 {
+		compatible = "sigma,smp8642-ir";
+		reg = <0x10518 0x18>, <0x105e0 0x1c>;
+		interrupts = <21 IRQ_TYPE_EDGE_RISING>;
+		clocks = <&xtal>;
+	};
diff --git a/Documentation/devicetree/bindings/media/tegra-cec.txt b/Documentation/devicetree/bindings/media/tegra-cec.txt
new file mode 100644
index 000000000..c503f06f3
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/tegra-cec.txt
@@ -0,0 +1,27 @@
+* Tegra HDMI CEC hardware
+
+The HDMI CEC module is present in Tegra SoCs and its purpose is to
+handle communication between HDMI connected devices over the CEC bus.
+
+Required properties:
+  - compatible : value should be one of the following:
+	"nvidia,tegra114-cec"
+	"nvidia,tegra124-cec"
+	"nvidia,tegra210-cec"
+  - reg : Physical base address of the IP registers and length of memory
+	  mapped region.
+  - interrupts : HDMI CEC interrupt number to the CPU.
+  - clocks : from common clock binding: handle to HDMI CEC clock.
+  - clock-names : from common clock binding: must contain "cec",
+		  corresponding to the entry in the clocks property.
+  - hdmi-phandle : phandle to the HDMI controller, see also cec.txt.
+
+Example:
+
+cec@70015000 {
+	compatible = "nvidia,tegra124-cec";
+	reg = <0x0 0x70015000 0x0 0x00001000>;
+	interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+	clocks = <&tegra_car TEGRA124_CLK_CEC>;
+	clock-names = "cec";
+};
diff --git a/Documentation/devicetree/bindings/media/ti,da850-vpif.txt b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
new file mode 100644
index 000000000..e47c7ccc5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/ti,da850-vpif.txt
@@ -0,0 +1,106 @@
+Texas Instruments VPIF
+----------------------
+
+The TI Video Port InterFace (VPIF) is the primary component for video
+capture and display on the DA850/AM18x family of TI DaVinci/Sitara
+SoCs.
+
+TI Document reference: SPRUH82C, Chapter 35
+http://www.ti.com/lit/pdf/spruh82
+
+Required properties:
+- compatible: must be "ti,da850-vpif"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the VPIF
+
+Video Capture:
+
+VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a
+single 16-bit channel. It should contain one or two port child nodes
+with child 'endpoint' node. If there are two ports then port@0 must
+describe the input and port@1 output channels. Please refer to the
+bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example using 2 8-bit input channels, one of which is connected to an
+I2C-connected TVP5147 decoder:
+
+	vpif: vpif@217000 {
+		compatible = "ti,da850-vpif";
+		reg = <0x217000 0x1000>;
+		interrupts = <92>;
+
+		port@0 {
+			vpif_input_ch0: endpoint@0 {
+				reg = <0>;
+				bus-width = <8>;
+				remote-endpoint = <&composite_in>;
+			};
+
+			vpif_input_ch1: endpoint@1 {
+				reg = <1>;
+				bus-width = <8>;
+				data-shift = <8>;
+			};
+		};
+
+		port@1 {
+			vpif_output_ch0: endpoint {
+				bus-width = <8>;
+				remote-endpoint = <&composite_out>;
+			};
+		};
+	};
+
+[ ... ]
+
+&i2c0 {
+
+	tvp5147@5d {
+		compatible = "ti,tvp5147";
+		reg = <0x5d>;
+
+		port {
+			composite_in: endpoint {
+				hsync-active = <1>;
+				vsync-active = <1>;
+				pclk-sample = <0>;
+
+				/* VPIF channel 0 (lower 8-bits) */
+				remote-endpoint = <&vpif_input_ch0>;
+				bus-width = <8>;
+			};
+		};
+	};
+
+	adv7343@2a {
+		compatible = "adi,adv7343";
+		reg = <0x2a>;
+
+		port {
+			composite_out: endpoint {
+				adi,dac-enable = <1 1 1>;
+				adi,sd-dac-enable = <1>;
+
+				remote-endpoint = <&vpif_output_ch0>;
+				bus-width = <8>;
+			};
+		};
+	};
+};
+
+
+Alternatively, an example when the bus is configured as a single
+16-bit input (e.g. for raw-capture mode):
+
+	vpif: vpif@217000 {
+		compatible = "ti,da850-vpif";
+		reg = <0x217000 0x1000>;
+		interrupts = <92>;
+
+		port {
+			vpif_ch0: endpoint {
+				  bus-width = <16>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/ti,omap3isp.txt b/Documentation/devicetree/bindings/media/ti,omap3isp.txt
new file mode 100644
index 000000000..ac23de855
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/ti,omap3isp.txt
@@ -0,0 +1,71 @@
+OMAP 3 ISP Device Tree bindings
+===============================
+
+The DT definitions can be found in include/dt-bindings/media/omap3-isp.h.
+
+Required properties
+===================
+
+compatible	: must contain "ti,omap3-isp"
+
+reg		: the two registers sets (physical address and length) for the
+		  ISP. The first set contains the core ISP registers up to
+		  the end of the SBL block. The second set contains the
+		  CSI PHYs and receivers registers.
+interrupts	: the ISP interrupt specifier
+iommus		: phandle and IOMMU specifier for the IOMMU that serves the ISP
+syscon		: the phandle and register offset to the Complex I/O or CSI-PHY
+		  register
+ti,phy-type	: 0 -- OMAP3ISP_PHY_TYPE_COMPLEX_IO (e.g. 3430)
+		  1 -- OMAP3ISP_PHY_TYPE_CSIPHY (e.g. 3630)
+#clock-cells	: Must be 1 --- the ISP provides two external clocks,
+		  cam_xclka and cam_xclkb, at indices 0 and 1,
+		  respectively. Please find more information on common
+		  clock bindings in ../clock/clock-bindings.txt.
+
+Port nodes (optional)
+---------------------
+
+More documentation on these bindings is available in
+video-interfaces.txt in the same directory.
+
+reg		: The interface:
+		  0 - parallel (CCDC)
+		  1 - CSIPHY1 -- CSI2C / CCP2B on 3630;
+		      CSI1 -- CSIb on 3430
+		  2 - CSIPHY2 -- CSI2A / CCP2B on 3630;
+		      CSI2 -- CSIa on 3430
+
+Optional properties
+===================
+
+vdd-csiphy1-supply : voltage supply of the CSI-2 PHY 1
+vdd-csiphy2-supply : voltage supply of the CSI-2 PHY 2
+
+Endpoint nodes
+--------------
+
+lane-polarities	: lane polarity (required on CSI-2)
+		  0 -- not inverted; 1 -- inverted
+data-lanes	: an array of data lanes from 1 to 3. The length can
+		  be either 1 or 2. (required on CSI-2)
+clock-lanes	: the clock lane (from 1 to 3). (required on CSI-2)
+
+
+Example
+=======
+
+		isp@480bc000 {
+			compatible = "ti,omap3-isp";
+			reg = <0x480bc000 0x12fc
+			       0x480bd800 0x0600>;
+			interrupts = <24>;
+			iommus = <&mmu_isp>;
+			syscon = <&scm_conf 0x2f0>;
+			ti,phy-type = <OMAP3ISP_PHY_TYPE_CSIPHY>;
+			#clock-cells = <1>;
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+			};
+		};
diff --git a/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt
new file mode 100644
index 000000000..3932e7665
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/ti-am437x-vpfe.txt
@@ -0,0 +1,61 @@
+Texas Instruments AM437x CAMERA (VPFE)
+--------------------------------------
+
+The Video Processing Front End (VPFE) is a key component for image capture
+applications. The capture module provides the system interface and the
+processing capability to connect RAW image-sensor modules and video decoders
+to the AM437x device.
+
+Required properties:
+- compatible: must be "ti,am437x-vpfe"
+- reg: physical base address and length of the registers set for the device;
+- interrupts: should contain IRQ line for the VPFE;
+- ti,am437x-vpfe-interface: can be one of the following,
+	0 - Raw Bayer Interface.
+	1 - 8 Bit BT656 Interface.
+	2 - 10 Bit BT656 Interface.
+	3 - YCbCr 8 Bit Interface.
+	4 - YCbCr 16 Bit Interface.
+
+VPFE supports a single port node with parallel bus. It should contain one
+'port' child node with child 'endpoint' node. Please refer to the bindings
+defined in Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+	vpfe: vpfe@f0034000 {
+		compatible = "ti,am437x-vpfe";
+		reg = <0x48328000 0x2000>;
+		interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+
+		pinctrl-names = "default", "sleep";
+		pinctrl-0 = <&vpfe_pins_default>;
+		pinctrl-1 = <&vpfe_pins_sleep>;
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			vpfe0_ep: endpoint {
+				remote-endpoint = <&ov2659_1>;
+				ti,am437x-vpfe-interface = <0>;
+				bus-width = <8>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+			};
+		};
+	};
+
+	i2c1: i2c@4802a000 {
+
+		ov2659@30 {
+			compatible = "ti,ov2659";
+			reg = <0x30>;
+
+			port {
+				ov2659_1: endpoint {
+					remote-endpoint = <&vpfe0_ep>;
+					bus-width = <8>;
+					mclk-frequency = <12000000>;
+				};
+			};
+	};
diff --git a/Documentation/devicetree/bindings/media/ti-cal.txt b/Documentation/devicetree/bindings/media/ti-cal.txt
new file mode 100644
index 000000000..ae9b52f37
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/ti-cal.txt
@@ -0,0 +1,72 @@
+Texas Instruments DRA72x CAMERA ADAPTATION LAYER (CAL)
+------------------------------------------------------
+
+The Camera Adaptation Layer (CAL) is a key component for image capture
+applications. The capture module provides the system interface and the
+processing capability to connect CSI2 image-sensor modules to the
+DRA72x device.
+
+Required properties:
+- compatible: must be "ti,dra72-cal"
+- reg:	CAL Top level, Receiver Core #0, Receiver Core #1 and Camera RX
+	control address space
+- reg-names: cal_top, cal_rx_core0, cal_rx_core1, and camerrx_control
+	     registers
+- interrupts: should contain IRQ line for the CAL;
+
+CAL supports 2 camera port nodes on MIPI bus. Each CSI2 camera port nodes
+should contain a 'port' child node with child 'endpoint' node. Please
+refer to the bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt.
+
+Example:
+	cal: cal@4845b000 {
+		compatible = "ti,dra72-cal";
+		ti,hwmods = "cal";
+		reg = <0x4845B000 0x400>,
+		      <0x4845B800 0x40>,
+		      <0x4845B900 0x40>,
+		      <0x4A002e94 0x4>;
+		reg-names = "cal_top",
+			    "cal_rx_core0",
+			    "cal_rx_core1",
+			    "camerrx_control";
+		interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			csi2_0: port@0 {
+				reg = <0>;
+				endpoint {
+					slave-mode;
+					remote-endpoint = <&ar0330_1>;
+				};
+			};
+			csi2_1: port@1 {
+				reg = <1>;
+			};
+		};
+	};
+
+	i2c5: i2c@4807c000 {
+		ar0330@10 {
+			compatible = "ti,ar0330";
+			reg = <0x10>;
+
+			port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ar0330_1: endpoint {
+					reg = <0>;
+					clock-lanes = <1>;
+					data-lanes = <0 2 3 4>;
+					remote-endpoint = <&csi2_0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/video-interfaces.txt b/Documentation/devicetree/bindings/media/video-interfaces.txt
new file mode 100644
index 000000000..baf9d9756
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/video-interfaces.txt
@@ -0,0 +1,273 @@
+Common bindings for video receiver and transmitter interfaces
+
+General concept
+---------------
+
+Video data pipelines usually consist of external devices, e.g. camera sensors,
+controlled over an I2C, SPI or UART bus, and SoC internal IP blocks, including
+video DMA engines and video data processors.
+
+SoC internal blocks are described by DT nodes, placed similarly to other SoC
+blocks.  External devices are represented as child nodes of their respective
+bus controller nodes, e.g. I2C.
+
+Data interfaces on all video devices are described by their child 'port' nodes.
+Configuration of a port depends on other devices participating in the data
+transfer and is described by 'endpoint' subnodes.
+
+device {
+	...
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			...
+			endpoint@0 { ... };
+			endpoint@1 { ... };
+		};
+		port@1 { ... };
+	};
+};
+
+If a port can be configured to work with more than one remote device on the same
+bus, an 'endpoint' child node must be provided for each of them.  If more than
+one port is present in a device node or there is more than one endpoint at a
+port, or port node needs to be associated with a selected hardware interface,
+a common scheme using '#address-cells', '#size-cells' and 'reg' properties is
+used.
+
+All 'port' nodes can be grouped under optional 'ports' node, which allows to
+specify #address-cells, #size-cells properties independently for the 'port'
+and 'endpoint' nodes and any child device nodes a device might have.
+
+Two 'endpoint' nodes are linked with each other through their 'remote-endpoint'
+phandles.  An endpoint subnode of a device contains all properties needed for
+configuration of this device for data exchange with other device.  In most
+cases properties at the peer 'endpoint' nodes will be identical, however they
+might need to be different when there is any signal modifications on the bus
+between two devices, e.g. there are logic signal inverters on the lines.
+
+It is allowed for multiple endpoints at a port to be active simultaneously,
+where supported by a device.  For example, in case where a data interface of
+a device is partitioned into multiple data busses, e.g. 16-bit input port
+divided into two separate ITU-R BT.656 8-bit busses.  In such case bus-width
+and data-shift properties can be used to assign physical data lines to each
+endpoint node (logical bus).
+
+Documenting bindings for devices
+--------------------------------
+
+All required and optional bindings the device supports shall be explicitly
+documented in device DT binding documentation. This also includes port and
+endpoint nodes for the device, including unit-addresses and reg properties where
+relevant.
+
+Please also see Documentation/devicetree/bindings/graph.txt .
+
+Required properties
+-------------------
+
+If there is more than one 'port' or more than one 'endpoint' node or 'reg'
+property is present in port and/or endpoint nodes the following properties
+are required in a relevant parent node:
+
+ - #address-cells : number of cells required to define port/endpoint
+		    identifier, should be 1.
+ - #size-cells    : should be zero.
+
+
+Optional properties
+-------------------
+
+- flash-leds: An array of phandles, each referring to a flash LED, a sub-node
+  of the LED driver device node.
+
+- lens-focus: A phandle to the node of the focus lens controller.
+
+- rotation: The device, typically an image sensor, is not mounted upright,
+  but a number of degrees counter clockwise. Typical values are 0 and 180
+  (upside down).
+
+
+Optional endpoint properties
+----------------------------
+
+- remote-endpoint: phandle to an 'endpoint' subnode of a remote device node.
+- slave-mode: a boolean property indicating that the link is run in slave mode.
+  The default when this property is not specified is master mode. In the slave
+  mode horizontal and vertical synchronization signals are provided to the
+  slave device (data source) by the master device (data sink). In the master
+  mode the data source device is also the source of the synchronization signals.
+- bus-type: data bus type. Possible values are:
+  0 - autodetect based on other properties (MIPI CSI-2 D-PHY, parallel or Bt656)
+  1 - MIPI CSI-2 C-PHY
+  2 - MIPI CSI1
+  3 - CCP2
+- bus-width: number of data lines actively used, valid for the parallel busses.
+- data-shift: on the parallel data busses, if bus-width is used to specify the
+  number of data lines, data-shift can be used to specify which data lines are
+  used, e.g. "bus-width=<8>; data-shift=<2>;" means, that lines 9:2 are used.
+- hsync-active: active state of the HSYNC signal, 0/1 for LOW/HIGH respectively.
+- vsync-active: active state of the VSYNC signal, 0/1 for LOW/HIGH respectively.
+  Note, that if HSYNC and VSYNC polarities are not specified, embedded
+  synchronization may be required, where supported.
+- data-active: similar to HSYNC and VSYNC, specifies data line polarity.
+- data-enable-active: similar to HSYNC and VSYNC, specifies the data enable
+  signal polarity.
+- field-even-active: field signal level during the even field data transmission.
+- pclk-sample: sample data on rising (1) or falling (0) edge of the pixel clock
+  signal.
+- sync-on-green-active: active state of Sync-on-green (SoG) signal, 0/1 for
+  LOW/HIGH respectively.
+- data-lanes: an array of physical data lane indexes. Position of an entry
+  determines the logical lane number, while the value of an entry indicates
+  physical lane, e.g. for 2-lane MIPI CSI-2 bus we could have
+  "data-lanes = <1 2>;", assuming the clock lane is on hardware lane 0.
+  If the hardware does not support lane reordering, monotonically
+  incremented values shall be used from 0 or 1 onwards, depending on
+  whether or not there is also a clock lane. This property is valid for
+  serial busses only (e.g. MIPI CSI-2).
+- clock-lanes: an array of physical clock lane indexes. Position of an entry
+  determines the logical lane number, while the value of an entry indicates
+  physical lane, e.g. for a MIPI CSI-2 bus we could have "clock-lanes = <0>;",
+  which places the clock lane on hardware lane 0. This property is valid for
+  serial busses only (e.g. MIPI CSI-2). Note that for the MIPI CSI-2 bus this
+  array contains only one entry.
+- clock-noncontinuous: a boolean property to allow MIPI CSI-2 non-continuous
+  clock mode.
+- link-frequencies: Allowed data bus frequencies. For MIPI CSI-2, for
+  instance, this is the actual frequency of the bus, not bits per clock per
+  lane value. An array of 64-bit unsigned integers.
+- lane-polarities: an array of polarities of the lanes starting from the clock
+  lane and followed by the data lanes in the same order as in data-lanes.
+  Valid values are 0 (normal) and 1 (inverted). The length of the array
+  should be the combined length of data-lanes and clock-lanes properties.
+  If the lane-polarities property is omitted, the value must be interpreted
+  as 0 (normal). This property is valid for serial busses only.
+- strobe: Whether the clock signal is used as clock (0) or strobe (1). Used
+  with CCP2, for instance.
+
+Example
+-------
+
+The example snippet below describes two data pipelines.  ov772x and imx074 are
+camera sensors with a parallel and serial (MIPI CSI-2) video bus respectively.
+Both sensors are on the I2C control bus corresponding to the i2c0 controller
+node.  ov772x sensor is linked directly to the ceu0 video host interface.
+imx074 is linked to ceu0 through the MIPI CSI-2 receiver (csi2). ceu0 has a
+(single) DMA engine writing captured data to memory.  ceu0 node has a single
+'port' node which may indicate that at any time only one of the following data
+pipelines can be active: ov772x -> ceu0 or imx074 -> csi2 -> ceu0.
+
+	ceu0: ceu@fe910000 {
+		compatible = "renesas,sh-mobile-ceu";
+		reg = <0xfe910000 0xa0>;
+		interrupts = <0x880>;
+
+		mclk: master_clock {
+			compatible = "renesas,ceu-clock";
+			#clock-cells = <1>;
+			clock-frequency = <50000000>;	/* Max clock frequency */
+			clock-output-names = "mclk";
+		};
+
+		port {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			/* Parallel bus endpoint */
+			ceu0_1: endpoint@1 {
+				reg = <1>;		/* Local endpoint # */
+				remote = <&ov772x_1_1>;	/* Remote phandle */
+				bus-width = <8>;	/* Used data lines */
+				data-shift = <2>;	/* Lines 9:2 are used */
+
+				/* If hsync-active/vsync-active are missing,
+				   embedded BT.656 sync is used */
+				hsync-active = <0>;	/* Active low */
+				vsync-active = <0>;	/* Active low */
+				data-active = <1>;	/* Active high */
+				pclk-sample = <1>;	/* Rising */
+			};
+
+			/* MIPI CSI-2 bus endpoint */
+			ceu0_0: endpoint@0 {
+				reg = <0>;
+				remote = <&csi2_2>;
+			};
+		};
+	};
+
+	i2c0: i2c@fff20000 {
+		...
+		ov772x_1: camera@21 {
+			compatible = "ovti,ov772x";
+			reg = <0x21>;
+			vddio-supply = <&regulator1>;
+			vddcore-supply = <&regulator2>;
+
+			clock-frequency = <20000000>;
+			clocks = <&mclk 0>;
+			clock-names = "xclk";
+
+			port {
+				/* With 1 endpoint per port no need for addresses. */
+				ov772x_1_1: endpoint {
+					bus-width = <8>;
+					remote-endpoint = <&ceu0_1>;
+					hsync-active = <1>;
+					vsync-active = <0>; /* Who came up with an
+							       inverter here ?... */
+					data-active = <1>;
+					pclk-sample = <1>;
+				};
+			};
+		};
+
+		imx074: camera@1a {
+			compatible = "sony,imx074";
+			reg = <0x1a>;
+			vddio-supply = <&regulator1>;
+			vddcore-supply = <&regulator2>;
+
+			clock-frequency = <30000000>;	/* Shared clock with ov772x_1 */
+			clocks = <&mclk 0>;
+			clock-names = "sysclk";		/* Assuming this is the
+							   name in the datasheet */
+			port {
+				imx074_1: endpoint {
+					clock-lanes = <0>;
+					data-lanes = <1 2>;
+					remote-endpoint = <&csi2_1>;
+				};
+			};
+		};
+	};
+
+	csi2: csi2@ffc90000 {
+		compatible = "renesas,sh-mobile-csi2";
+		reg = <0xffc90000 0x1000>;
+		interrupts = <0x17a0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@1 {
+			compatible = "renesas,csi2c";	/* One of CSI2I and CSI2C. */
+			reg = <1>;			/* CSI-2 PHY #1 of 2: PHY_S,
+							   PHY_M has port address 0,
+							   is unused. */
+			csi2_1: endpoint {
+				clock-lanes = <0>;
+				data-lanes = <2 1>;
+				remote-endpoint = <&imx074_1>;
+			};
+		};
+		port@2 {
+			reg = <2>;			/* port 2: link to the CEU */
+
+			csi2_2: endpoint {
+				remote-endpoint = <&ceu0_0>;
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/video-mux.txt b/Documentation/devicetree/bindings/media/video-mux.txt
new file mode 100644
index 000000000..63b9dc913
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/video-mux.txt
@@ -0,0 +1,60 @@
+Video Multiplexer
+=================
+
+Video multiplexers allow to select between multiple input ports. Video received
+on the active input port is passed through to the output port. Muxes described
+by this binding are controlled by a multiplexer controller that is described by
+the bindings in Documentation/devicetree/bindings/mux/mux-controller.txt
+
+Required properties:
+- compatible : should be "video-mux"
+- mux-controls : mux controller node to use for operating the mux
+- #address-cells: should be <1>
+- #size-cells: should be <0>
+- port@*: at least three port nodes containing endpoints connecting to the
+  source and sink devices according to of_graph bindings. The last port is
+  the output port, all others are inputs.
+
+Optionally, #address-cells, #size-cells, and port nodes can be grouped under a
+ports node as described in Documentation/devicetree/bindings/graph.txt.
+
+Example:
+
+	mux: mux-controller {
+		compatible = "gpio-mux";
+		#mux-control-cells = <0>;
+
+		mux-gpios = <&gpio1 15 GPIO_ACTIVE_HIGH>;
+	};
+
+	video-mux {
+		compatible = "video-mux";
+		mux-controls = <&mux>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port@0 {
+			reg = <0>;
+
+			mux_in0: endpoint {
+				remote-endpoint = <&video_source0_out>;
+			};
+		};
+
+		port@1 {
+			reg = <1>;
+
+			mux_in1: endpoint {
+				remote-endpoint = <&video_source1_out>;
+			};
+		};
+
+		port@2 {
+			reg = <2>;
+
+			mux_out: endpoint {
+				remote-endpoint = <&capture_interface_in>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/media/xilinx/video.txt b/Documentation/devicetree/bindings/media/xilinx/video.txt
new file mode 100644
index 000000000..68ac210e6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/xilinx/video.txt
@@ -0,0 +1,35 @@
+DT bindings for Xilinx video IP cores
+-------------------------------------
+
+Xilinx video IP cores process video streams by acting as video sinks and/or
+sources. They are connected by links through their input and output ports,
+creating a video pipeline.
+
+Each video IP core is represented by an AMBA bus child node in the device
+tree using bindings documented in this directory. Connections between the IP
+cores are represented as defined in ../video-interfaces.txt.
+
+The whole  pipeline is represented by an AMBA bus child node in the device
+tree using bindings documented in ./xlnx,video.txt.
+
+Common properties
+-----------------
+
+The following properties are common to all Xilinx video IP cores.
+
+- xlnx,video-format: This property represents a video format transmitted on an
+  AXI bus between video IP cores, using its VF code as defined in "AXI4-Stream
+  Video IP and System Design Guide" [UG934]. How the format relates to the IP
+  core is described in the IP core bindings documentation.
+
+- xlnx,video-width: This property qualifies the video format with the sample
+  width expressed as a number of bits per pixel component. All components must
+  use the same width.
+
+- xlnx,cfa-pattern: When the video format is set to Mono/Sensor, this property
+  describes the sensor's color filter array pattern. Supported values are
+  "bggr", "gbrg", "grbg", "rggb" and "mono". If not specified, the pattern
+  defaults to "mono".
+
+
+[UG934] http://www.xilinx.com/support/documentation/ip_documentation/axi_videoip/v1_0/ug934_axi_videoIP.pdf
diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt
new file mode 100644
index 000000000..2aed3b4a6
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tc.txt
@@ -0,0 +1,33 @@
+Xilinx Video Timing Controller (VTC)
+------------------------------------
+
+The Video Timing Controller is a general purpose video timing generator and
+detector.
+
+Required properties:
+
+  - compatible: Must be "xlnx,v-tc-6.1".
+
+  - reg: Physical base address and length of the registers set for the device.
+
+  - clocks: Must contain a clock specifier for the VTC core and timing
+    interfaces clock.
+
+Optional properties:
+
+  - xlnx,detector: The VTC has a timing detector
+  - xlnx,generator: The VTC has a timing generator
+
+  At least one of the xlnx,detector and xlnx,generator properties must be
+  specified.
+
+
+Example:
+
+	vtc: vtc@43c40000 {
+		compatible = "xlnx,v-tc-6.1";
+		reg = <0x43c40000 0x10000>;
+
+		clocks = <&clkc 15>;
+		xlnx,generator;
+	};
diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt
new file mode 100644
index 000000000..439351ab2
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,v-tpg.txt
@@ -0,0 +1,71 @@
+Xilinx Video Test Pattern Generator (TPG)
+-----------------------------------------
+
+Required properties:
+
+- compatible: Must contain at least one of
+
+    "xlnx,v-tpg-5.0" (TPG version 5.0)
+    "xlnx,v-tpg-6.0" (TPG version 6.0)
+
+  TPG versions backward-compatible with previous versions should list all
+  compatible versions in the newer to older order.
+
+- reg: Physical base address and length of the registers set for the device.
+
+- clocks: Reference to the video core clock.
+
+- xlnx,video-format, xlnx,video-width: Video format and width, as defined in
+  video.txt.
+
+- port: Video port, using the DT bindings defined in ../video-interfaces.txt.
+  The TPG has a single output port numbered 0.
+
+Optional properties:
+
+- xlnx,vtc: A phandle referencing the Video Timing Controller that generates
+  video timings for the TPG test patterns.
+
+- timing-gpios: Specifier for a GPIO that controls the timing mux at the TPG
+  input. The GPIO active level corresponds to the selection of VTC-generated
+  video timings.
+
+The xlnx,vtc and timing-gpios properties are mandatory when the TPG is
+synthesized with two ports and forbidden when synthesized with one port.
+
+Example:
+
+	tpg_0: tpg@40050000 {
+		compatible = "xlnx,v-tpg-6.0", "xlnx,v-tpg-5.0";
+		reg = <0x40050000 0x10000>;
+		clocks = <&clkc 15>;
+
+		xlnx,vtc = <&vtc_3>;
+		timing-gpios = <&ps7_gpio_0 55 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				tpg_in: endpoint {
+					remote-endpoint = <&adv7611_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+
+				xlnx,video-format = <XVIP_VF_YUV_422>;
+				xlnx,video-width = <8>;
+
+				tpg1_out: endpoint {
+					remote-endpoint = <&switch_in0>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt
new file mode 100644
index 000000000..5a0227023
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/xilinx/xlnx,video.txt
@@ -0,0 +1,55 @@
+Xilinx Video IP Pipeline (VIPP)
+-------------------------------
+
+General concept
+---------------
+
+Xilinx video IP pipeline processes video streams through one or more Xilinx
+video IP cores. Each video IP core is represented as documented in video.txt
+and IP core specific documentation, xlnx,v-*.txt, in this directory. The DT
+node of the VIPP represents as a top level node of the pipeline and defines
+mappings between DMAs and the video IP cores.
+
+Required properties:
+
+- compatible: Must be "xlnx,video".
+
+- dmas, dma-names: List of one DMA specifier and identifier string (as defined
+  in Documentation/devicetree/bindings/dma/dma.txt) per port. Each port
+  requires a DMA channel with the identifier string set to "port" followed by
+  the port index.
+
+- ports: Video port, using the DT bindings defined in ../video-interfaces.txt.
+
+Required port properties:
+
+- direction: should be either "input" or "output" depending on the direction
+  of stream.
+
+Example:
+
+	video_cap {
+		compatible = "xlnx,video";
+		dmas = <&vdma_1 1>, <&vdma_3 1>;
+		dma-names = "port0", "port1";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				direction = "input";
+				vcap0_in0: endpoint {
+					remote-endpoint = <&scaler0_out>;
+				};
+			};
+			port@1 {
+				reg = <1>;
+				direction = "input";
+				vcap0_in1: endpoint {
+					remote-endpoint = <&switch_out1>;
+				};
+			};
+		};
+	};
diff --git a/Documentation/devicetree/bindings/media/zx-irdec.txt b/Documentation/devicetree/bindings/media/zx-irdec.txt
new file mode 100644
index 000000000..295b9fab5
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/zx-irdec.txt
@@ -0,0 +1,14 @@
+IR Decoder (IRDEC) on ZTE ZX family SoCs
+
+Required properties:
+ - compatible: Should be "zte,zx296718-irdec".
+ - reg: Physical base address and length of IRDEC registers.
+ - interrupts: Interrupt number of IRDEC.
+
+Exmaples:
+
+	irdec: ir-decoder@111000 {
+		compatible = "zte,zx296718-irdec";
+		reg = <0x111000 0x1000>;
+		interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
+	};