Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 193 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/mfd/max77693.txt b/Documentation/devicetree/bindings/mfd/max77693.txt
new file mode 100644
index 000000000..a3c60a7a3
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77693.txt
@@ -0,0 +1,193 @@
+Maxim MAX77693 multi-function device
+
+MAX77693 is a Multifunction device with the following submodules:
+- PMIC,
+- CHARGER,
+- LED,
+- MUIC,
+- HAPTIC
+
+It is interfaced to host controller using i2c.
+This document describes the bindings for the mfd device.
+
+Required properties:
+- compatible : Must be "maxim,max77693".
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+
+Optional properties:
+- regulators : The regulators of max77693 have to be instantiated under subnode
+  named "regulators" using the following format.
+
+	regulators {
+		regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER
+		standard regulator constraints[*].
+	};
+
+	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide
+  users with tactile feedback. PWM period and duty-cycle are varied in
+  order to provide the appropriate level of feedback.
+
+ Required properties:
+	- compatible : Must be "maxim,max77693-haptic"
+	- haptic-supply : power supply for the haptic motor
+	[*] refer Documentation/devicetree/bindings/regulator/regulator.txt
+	- pwms : phandle to the physical PWM(Pulse Width Modulation) device.
+	 PWM properties should be named "pwms". And number of cell is different
+	 for each pwm device.
+	 To get more information, please refer to documentation.
+	[*] refer Documentation/devicetree/bindings/pwm/pwm.txt
+
+- charger : Node configuring the charger driver.
+  If present, required properties:
+  - compatible : Must be "maxim,max77693-charger".
+
+  Optional properties (if not set, defaults will be used):
+  - maxim,constant-microvolt : Battery constant voltage in uV. The charger
+    will operate in fast charge constant current mode till battery voltage
+    reaches this level. Then the charger will switch to fast charge constant
+    voltage mode. Also vsys (system voltage) will be set to this value when
+    DC power is supplied but charger is not enabled.
+    Valid values: 3650000 - 4400000, step by 25000 (rounded down)
+    Default: 4200000
+
+  - maxim,min-system-microvolt : Minimal system voltage in uV.
+    Valid values: 3000000 - 3700000, step by 100000 (rounded down)
+    Default: 3600000
+
+  - maxim,thermal-regulation-celsius : Temperature in Celsius for entering
+    high temperature charging mode. If die temperature exceeds this value
+    the charging current will be reduced by 105 mA/Celsius.
+    Valid values: 70, 85, 100, 115
+    Default: 100
+
+  - maxim,battery-overcurrent-microamp : Overcurrent protection threshold
+    in uA (current from battery to system).
+    Valid values: 2000000 - 3500000, step by 250000 (rounded down)
+    Default: 3500000
+
+  - maxim,charge-input-threshold-microvolt : Threshold voltage in uV for
+    triggering input voltage regulation loop. If input voltage decreases
+    below this value, the input current will be reduced to reach the
+    threshold voltage.
+    Valid values: 4300000, 4700000, 4800000, 4900000
+    Default: 4300000
+
+- led : the LED submodule device node
+
+There are two LED outputs available - FLED1 and FLED2. Each of them can
+control a separate LED or they can be connected together to double
+the maximum current for a single connected LED. One LED is represented
+by one child node.
+
+Required properties:
+- compatible : Must be "maxim,max77693-led".
+
+Optional properties:
+- maxim,boost-mode :
+	In boost mode the device can produce up to 1.2A of total current
+	on both outputs. The maximum current on each output is reduced
+	to 625mA then. If not enabled explicitly, boost setting defaults to
+	LEDS_BOOST_FIXED in case both current sources are used.
+	Possible values:
+		LEDS_BOOST_OFF (0) - no boost,
+		LEDS_BOOST_ADAPTIVE (1) - adaptive mode,
+		LEDS_BOOST_FIXED (2) - fixed mode.
+- maxim,boost-mvout : Output voltage of the boost module in millivolts.
+	Valid values: 3300 - 5500, step by 25 (rounded down)
+	Default: 3300
+- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired
+	if chip estimates that system voltage could drop below this level due
+	to flash power consumption.
+	Valid values: 2400 - 3400, step by 33 (rounded down)
+	Default: 2400
+
+Required properties for the LED child node:
+- led-sources : see Documentation/devicetree/bindings/leds/common.txt;
+		device current output identifiers: 0 - FLED1, 1 - FLED2
+- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values for a LED connected to one FLED output:
+		15625 - 250000, step by 15625 (rounded down)
+	Valid values for a LED connected to both FLED outputs:
+		15625 - 500000, step by 15625 (rounded down)
+- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values for a single LED connected to one FLED output
+	(boost mode must be turned off):
+		15625 - 1000000, step by 15625 (rounded down)
+	Valid values for a single LED connected to both FLED outputs:
+		15625 - 1250000, step by 15625 (rounded down)
+	Valid values for two LEDs case:
+		15625 - 625000, step by 15625 (rounded down)
+- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt
+	Valid values: 62500 - 1000000, step by 62500 (rounded down)
+
+Optional properties for the LED child node:
+- label : see Documentation/devicetree/bindings/leds/common.txt
+
+Optional nodes:
+- max77693-muic :
+	Node used only by extcon consumers.
+	Required properties:
+		- compatible : "maxim,max77693-muic"
+
+Example:
+#include <dt-bindings/leds/common.h>
+
+	max77693@66 {
+		compatible = "maxim,max77693";
+		reg = <0x66>;
+		interrupt-parent = <&gpx1>;
+		interrupts = <5 2>;
+
+		regulators {
+			esafeout@1 {
+				regulator-compatible = "ESAFEOUT1";
+				regulator-name = "ESAFEOUT1";
+				regulator-boot-on;
+			};
+			esafeout@2 {
+				regulator-compatible = "ESAFEOUT2";
+				regulator-name = "ESAFEOUT2";
+				};
+			charger@0 {
+				regulator-compatible = "CHARGER";
+				regulator-name = "CHARGER";
+				regulator-min-microamp = <60000>;
+				regulator-max-microamp = <2580000>;
+					regulator-boot-on;
+			};
+		};
+
+		haptic {
+			compatible = "maxim,max77693-haptic";
+			haptic-supply = <&haptic_supply>;
+			pwms = <&pwm 0 40000 0>;
+			pwm-names = "haptic";
+		};
+
+		charger {
+			compatible = "maxim,max77693-charger";
+
+			maxim,constant-microvolt = <4200000>;
+			maxim,min-system-microvolt = <3600000>;
+			maxim,thermal-regulation-celsius = <75>;
+			maxim,battery-overcurrent-microamp = <3000000>;
+			maxim,charge-input-threshold-microvolt = <4300000>;
+
+		led {
+			compatible = "maxim,max77693-led";
+			maxim,boost-mode = <LEDS_BOOST_FIXED>;
+			maxim,boost-mvout = <5000>;
+			maxim,mvsys-min = <2400>;
+
+			camera_flash: flash-led {
+				label = "max77693-flash";
+				led-sources = <0>, <1>;
+				led-max-microamp = <500000>;
+				flash-max-microamp = <1250000>;
+				flash-max-timeout-us = <1000000>;
+			};
+		};
+	};