Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

11 files changed, 401 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/misc/allwinner,syscon.txt b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
new file mode 100644
index 000000000..31494a24f
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/allwinner,syscon.txt
@@ -0,0 +1,20 @@
+* Allwinner sun8i system controller
+
+This file describes the bindings for the system controller present in
+Allwinner SoC H3, A83T and A64.
+The principal function of this syscon is to control EMAC PHY choice and
+config.
+
+Required properties for the system controller:
+- reg: address and length of the register for the device.
+- compatible: should be "syscon" and one of the following string:
+		"allwinner,sun8i-h3-system-controller"
+		"allwinner,sun8i-v3s-system-controller"
+		"allwinner,sun50i-a64-system-controller"
+		"allwinner,sun8i-a83t-system-controller"
+
+Example:
+syscon: syscon@1c00000 {
+	compatible = "allwinner,sun8i-h3-system-controller", "syscon";
+	reg = <0x01c00000 0x1000>;
+};
diff --git a/Documentation/devicetree/bindings/misc/aspeed,cvic.txt b/Documentation/devicetree/bindings/misc/aspeed,cvic.txt
new file mode 100644
index 000000000..d62c783d1
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/aspeed,cvic.txt
@@ -0,0 +1,35 @@
+* ASPEED AST2400 and AST2500 coprocessor interrupt controller
+
+This file describes the bindings for the interrupt controller present
+in the AST2400 and AST2500 BMC SoCs which provides interrupt to the
+ColdFire coprocessor.
+
+It is not a normal interrupt controller and it would be rather
+inconvenient to create an interrupt tree for it as it somewhat shares
+some of the same sources as the main ARM interrupt controller but with
+different numbers.
+
+The AST2500 supports a SW generated interrupt
+
+Required properties:
+- reg: address and length of the register for the device.
+- compatible: "aspeed,cvic" and one of:
+		"aspeed,ast2400-cvic"
+	      or
+		"aspeed,ast2500-cvic"
+
+- valid-sources: One cell, bitmap of supported sources for the implementation
+
+Optional properties;
+- copro-sw-interrupts: List of interrupt numbers that can be used as
+		       SW interrupts from the ARM to the coprocessor.
+		       (AST2500 only)
+
+Example:
+
+	cvic: copro-interrupt-controller@1e6c2000 {
+		compatible = "aspeed,ast2500-cvic";
+		valid-sources = <0xffffffff>;
+		copro-sw-interrupts = <1>;
+		reg = <0x1e6c2000 0x80>;
+	};
diff --git a/Documentation/devicetree/bindings/misc/atmel-ssc.txt b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
new file mode 100644
index 000000000..f9fb41264
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/atmel-ssc.txt
@@ -0,0 +1,50 @@
+* Atmel SSC driver.
+
+Required properties:
+- compatible: "atmel,at91rm9200-ssc" or "atmel,at91sam9g45-ssc"
+	- atmel,at91rm9200-ssc: support pdc transfer
+	- atmel,at91sam9g45-ssc: support dma transfer
+- reg: Should contain SSC registers location and length
+- interrupts: Should contain SSC interrupt
+- clock-names: tuple listing input clock names.
+	Required elements: "pclk"
+- clocks: phandles to input clocks.
+
+
+Required properties for devices compatible with "atmel,at91sam9g45-ssc":
+- dmas: DMA specifier, consisting of a phandle to DMA controller node,
+  the memory interface and SSC DMA channel ID (for tx and rx).
+  See Documentation/devicetree/bindings/dma/atmel-dma.txt for details.
+- dma-names: Must be "tx", "rx".
+
+Optional properties:
+  - atmel,clk-from-rk-pin: bool property.
+     - When SSC works in slave mode, according to the hardware design, the
+       clock can get from TK pin, and also can get from RK pin. So, add
+       this parameter to choose where the clock from.
+     - By default the clock is from TK pin, if the clock from RK pin, this
+       property is needed.
+  - #sound-dai-cells: Should contain <0>.
+     - This property makes the SSC into an automatically registered DAI.
+
+Examples:
+- PDC transfer:
+ssc0: ssc@fffbc000 {
+	compatible = "atmel,at91rm9200-ssc";
+	reg = <0xfffbc000 0x4000>;
+	interrupts = <14 4 5>;
+	clocks = <&ssc0_clk>;
+	clock-names = "pclk";
+};
+
+- DMA transfer:
+ssc0: ssc@f0010000 {
+      compatible = "atmel,at91sam9g45-ssc";
+      reg = <0xf0010000 0x4000>;
+      interrupts = <28 4 5>;
+      dmas = <&dma0 1 13>,
+	     <&dma0 1 14>;
+      dma-names = "tx", "rx";
+      pinctrl-names = "default";
+      pinctrl-0 = <&pinctrl_ssc0_tx &pinctrl_ssc0_rx>;
+};
diff --git a/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt b/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt
new file mode 100644
index 000000000..05b47232e
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/brcm,kona-smc.txt
@@ -0,0 +1,15 @@
+Broadcom Secure Monitor Bounce buffer
+-----------------------------------------------------
+This binding defines the location of the bounce buffer
+used for non-secure to secure communications.
+
+Required properties:
+- compatible : "brcm,kona-smc"
+- DEPRECATED: compatible : "bcm,kona-smc"
+- reg : Location and size of bounce buffer
+
+Example:
+	smc@3404c000 {
+		compatible = "brcm,bcm11351-smc", "brcm,kona-smc";
+		reg = <0x3404c000 0x400>; //1 KiB in SRAM
+	};
diff --git a/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt
new file mode 100644
index 000000000..a8ebb4621
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/eeprom-93xx46.txt
@@ -0,0 +1,25 @@
+EEPROMs (SPI) compatible with Microchip Technology 93xx46 family.
+
+Required properties:
+- compatible : shall be one of:
+    "atmel,at93c46d"
+    "eeprom-93xx46"
+- data-size : number of data bits per word (either 8 or 16)
+
+Optional properties:
+- read-only : parameter-less property which disables writes to the EEPROM
+- select-gpios : if present, specifies the GPIO that will be asserted prior to
+  each access to the EEPROM (e.g. for SPI bus multiplexing)
+
+Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
+apply.  In particular, "reg" and "spi-max-frequency" properties must be given.
+
+Example:
+	eeprom@0 {
+		compatible = "eeprom-93xx46";
+		reg = <0>;
+		spi-max-frequency = <1000000>;
+		spi-cs-high;
+		data-size = <8>;
+		select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+	};
diff --git a/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt
new file mode 100644
index 000000000..6611a7c20
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/fsl,qoriq-mc.txt
@@ -0,0 +1,119 @@
+* Freescale Management Complex
+
+The Freescale Management Complex (fsl-mc) is a hardware resource
+manager that manages specialized hardware objects used in
+network-oriented packet processing applications. After the fsl-mc
+block is enabled, pools of hardware resources are available, such as
+queues, buffer pools, I/O interfaces. These resources are building
+blocks that can be used to create functional hardware objects/devices
+such as network interfaces, crypto accelerator instances, L2 switches,
+etc.
+
+Required properties:
+
+    - compatible
+        Value type: <string>
+        Definition: Must be "fsl,qoriq-mc".  A Freescale Management Complex
+                    compatible with this binding must have Block Revision
+                    Registers BRR1 and BRR2 at offset 0x0BF8 and 0x0BFC in
+                    the MC control register region.
+
+    - reg
+        Value type: <prop-encoded-array>
+        Definition: A standard property.  Specifies one or two regions
+                    defining the MC's registers:
+
+                       -the first region is the command portal for the
+                        this machine and must always be present
+
+                       -the second region is the MC control registers. This
+                        region may not be present in some scenarios, such
+                        as in the device tree presented to a virtual machine.
+
+    - msi-parent
+        Value type: <phandle>
+        Definition: Must be present and point to the MSI controller node
+                    handling message interrupts for the MC.
+
+    - ranges
+        Value type: <prop-encoded-array>
+        Definition: A standard property.  Defines the mapping between the child
+                    MC address space and the parent system address space.
+
+                    The MC address space is defined by 3 components:
+                       <region type> <offset hi> <offset lo>
+
+                    Valid values for region type are
+                       0x0 - MC portals
+                       0x1 - QBMAN portals
+
+    - #address-cells
+        Value type: <u32>
+        Definition: Must be 3.  (see definition in 'ranges' property)
+
+    - #size-cells
+        Value type: <u32>
+        Definition: Must be 1.
+
+Sub-nodes:
+
+        The fsl-mc node may optionally have dpmac sub-nodes that describe
+        the relationship between the Ethernet MACs which belong to the MC
+        and the Ethernet PHYs on the system board.
+
+        The dpmac nodes must be under a node named "dpmacs" which contains
+        the following properties:
+
+            - #address-cells
+              Value type: <u32>
+              Definition: Must be present if dpmac sub-nodes are defined and must
+                          have a value of 1.
+
+            - #size-cells
+              Value type: <u32>
+              Definition: Must be present if dpmac sub-nodes are defined and must
+                          have a value of 0.
+
+        These nodes must have the following properties:
+
+            - compatible
+              Value type: <string>
+              Definition: Must be "fsl,qoriq-mc-dpmac".
+
+            - reg
+              Value type: <prop-encoded-array>
+              Definition: Specifies the id of the dpmac.
+
+            - phy-handle
+              Value type: <phandle>
+              Definition: Specifies the phandle to the PHY device node associated
+                          with the this dpmac.
+
+Example:
+
+        fsl_mc: fsl-mc@80c000000 {
+                compatible = "fsl,qoriq-mc";
+                reg = <0x00000008 0x0c000000 0 0x40>,    /* MC portal base */
+                      <0x00000000 0x08340000 0 0x40000>; /* MC control reg */
+                msi-parent = <&its>;
+                #address-cells = <3>;
+                #size-cells = <1>;
+
+                /*
+                 * Region type 0x0 - MC portals
+                 * Region type 0x1 - QBMAN portals
+                 */
+                ranges = <0x0 0x0 0x0 0x8 0x0c000000 0x4000000
+                          0x1 0x0 0x0 0x8 0x18000000 0x8000000>;
+
+                dpmacs {
+                    #address-cells = <1>;
+                    #size-cells = <0>;
+
+                    dpmac@1 {
+                        compatible = "fsl,qoriq-mc-dpmac";
+                        reg = <1>;
+                        phy-handle = <&mdio0_phy0>;
+                    }
+                }
+        };
diff --git a/Documentation/devicetree/bindings/misc/ge-achc.txt b/Documentation/devicetree/bindings/misc/ge-achc.txt
new file mode 100644
index 000000000..77df94d7a
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/ge-achc.txt
@@ -0,0 +1,26 @@
+* GE Healthcare USB Management Controller
+
+A device which handles data aquisition from compatible USB based peripherals.
+SPI is used for device management.
+
+Note: This device does not expose the peripherals as USB devices.
+
+Required properties:
+
+- compatible : Should be "ge,achc"
+
+Required SPI properties:
+
+- reg : Should be address of the device chip select within
+  the controller.
+
+- spi-max-frequency : Maximum SPI clocking speed of device in Hz, should be
+  1MHz for the GE ACHC.
+
+Example:
+
+spidev0: spi@0 {
+	compatible = "ge,achc";
+	reg = <0>;
+	spi-max-frequency = <1000000>;
+};
diff --git a/Documentation/devicetree/bindings/misc/idt_89hpesx.txt b/Documentation/devicetree/bindings/misc/idt_89hpesx.txt
new file mode 100644
index 000000000..b9093b79a
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/idt_89hpesx.txt
@@ -0,0 +1,44 @@
+EEPROM / CSR SMBus-slave interface of IDT 89HPESx devices
+
+Required properties:
+  - compatible : should be "<manufacturer>,<type>"
+		 Basically there is only one manufacturer: idt, but some
+		 compatible devices may be produced in future. Following devices
+		 are supported: 89hpes8nt2, 89hpes12nt3, 89hpes24nt6ag2,
+		 89hpes32nt8ag2, 89hpes32nt8bg2, 89hpes12nt12g2, 89hpes16nt16g2,
+		 89hpes24nt24g2, 89hpes32nt24ag2, 89hpes32nt24bg2;
+		 89hpes12n3, 89hpes12n3a, 89hpes24n3, 89hpes24n3a;
+		 89hpes32h8, 89hpes32h8g2, 89hpes48h12, 89hpes48h12g2,
+		 89hpes48h12ag2, 89hpes16h16, 89hpes22h16, 89hpes22h16g2,
+		 89hpes34h16, 89hpes34h16g2, 89hpes64h16, 89hpes64h16g2,
+		 89hpes64h16ag2;
+		 89hpes12t3g2, 89hpes24t3g2, 89hpes16t4, 89hpes4t4g2,
+		 89hpes10t4g2, 89hpes16t4g2, 89hpes16t4ag2, 89hpes5t5,
+		 89hpes6t5, 89hpes8t5, 89hpes8t5a, 89hpes24t6, 89hpes6t6g2,
+		 89hpes24t6g2, 89hpes16t7, 89hpes32t8, 89hpes32t8g2,
+		 89hpes48t12, 89hpes48t12g2.
+  - reg :	 I2C address of the IDT 89HPESx device.
+
+Optionally there can be EEPROM-compatible subnode:
+  - compatible:  There are five EEPROM devices supported: 24c32, 24c64, 24c128,
+		 24c256 and 24c512 differed by size.
+  - reg:         Custom address of EEPROM device (If not specified IDT 89HPESx
+    (optional)	 device will try to communicate with EEPROM sited by default
+		 address - 0x50)
+  - read-only :	 Parameterless property disables writes to the EEPROM
+    (optional)
+
+Example:
+	idt@60 {
+		compatible = "idt,89hpes32nt8ag2";
+		reg = <0x74>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		eeprom@50 {
+			compatible = "onsemi,24c64";
+			reg = <0x50>;
+			read-only;
+		};
+	};
+
diff --git a/Documentation/devicetree/bindings/misc/ifm-csi.txt b/Documentation/devicetree/bindings/misc/ifm-csi.txt
new file mode 100644
index 000000000..5bdfffb0b
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/ifm-csi.txt
@@ -0,0 +1,41 @@
+IFM camera sensor interface on mpc5200 LocalPlus bus
+
+Required properties:
+- compatible: "ifm,o2d-csi"
+- reg: specifies sensor chip select number and associated address range
+- interrupts: external interrupt line number and interrupt sense mode
+  of the interrupt line signaling frame valid events
+- gpios: three gpio-specifiers for "capture", "reset" and "master enable"
+  GPIOs (strictly in this order).
+- ifm,csi-clk-handle: the phandle to a node in the DT describing the sensor
+  clock generator. This node is usually a general purpose timer controller.
+- ifm,csi-addr-bus-width: address bus width (valid values are 16, 24, 25)
+- ifm,csi-data-bus-width: data bus width (valid values are 8 and 16)
+- ifm,csi-wait-cycles: sensor bus wait cycles
+
+Optional properties:
+- ifm,csi-byte-swap: if this property is present, the byte swapping on
+  the bus will be enabled.
+
+Example:
+
+	csi@3,0 {
+		compatible = "ifm,o2d-csi";
+		reg = <3 0 0x00100000>;		/* CS 3, 1 MiB range */
+		interrupts = <1 1 2>;		/* IRQ1, edge falling */
+
+		ifm,csi-clk-handle = <&timer7>;
+		gpios = <&gpio_simple 23 0	/* image_capture */
+			 &gpio_simple 26 0	/* image_reset */
+			 &gpio_simple 29 0>;	/* image_master_en */
+
+		ifm,csi-addr-bus-width = <24>;
+		ifm,csi-data-bus-width = <8>;
+		ifm,csi-wait-cycles = <0>;
+	};
+
+The base address of the used chip select is specified in the
+ranges property of the parent localbus node, for example:
+
+	ranges = <0 0 0xff000000 0x01000000
+		  3 0 0xe3000000 0x00100000>;
diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt
new file mode 100644
index 000000000..892ba4384
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/nvidia,tegra186-misc.txt
@@ -0,0 +1,12 @@
+NVIDIA Tegra186 MISC register block
+
+The MISC register block found on Tegra186 SoCs contains registers that can be
+used to identify a given chip and various strapping options.
+
+Required properties:
+- compatible: Must be:
+  - Tegra186: "nvidia,tegra186-misc"
+- reg: Should contain 2 entries: The first entry gives the physical address
+       and length of the register region which contains revision and debug
+       features. The second entry specifies the physical address and length
+       of the register region indicating the strapping options.
diff --git a/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt
new file mode 100644
index 000000000..4556359c5
--- /dev/null
+++ b/Documentation/devicetree/bindings/misc/nvidia,tegra20-apbmisc.txt
@@ -0,0 +1,14 @@
+NVIDIA Tegra20/Tegra30/Tegr114/Tegra124 apbmisc block
+
+Required properties:
+- compatible : For Tegra20, must be "nvidia,tegra20-apbmisc".  For Tegra30,
+  must be "nvidia,tegra30-apbmisc".  Otherwise, must contain
+  "nvidia,<chip>-apbmisc", plus one of the above, where <chip> is tegra114,
+  tegra124, tegra132.
+- reg: Should contain 2 entries: the first entry gives the physical address
+       and length of the registers which contain revision and debug features.
+       The second entry gives the physical address and length of the
+       registers indicating the strapping options.
+
+Optional properties:
+- nvidia,long-ram-code: If present, the RAM code is long (4 bit). If not, short (2 bit).