Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

10 files changed, 531 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
new file mode 100644
index 000000000..cffb2d687
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/brcm,bcm43xx-fmac.txt
@@ -0,0 +1,38 @@
+Broadcom BCM43xx Fullmac wireless SDIO devices
+
+This node provides properties for controlling the Broadcom wireless device. The
+node is expected to be specified as a child node to the SDIO controller that
+connects the device to the system.
+
+Required properties:
+
+ - compatible : Should be "brcm,bcm4329-fmac".
+
+Optional properties:
+ - brcm,drive-strength : drive strength used for SDIO pins on device in mA
+	(default = 6).
+ - interrupts : specifies attributes for the out-of-band interrupt (host-wake).
+	When not specified the device will use in-band SDIO interrupts.
+ - interrupt-names : name of the out-of-band interrupt, which must be set
+	to "host-wake".
+
+Example:
+
+mmc3: mmc@1c12000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins_a>;
+	vmmc-supply = <&reg_vmmc3>;
+	bus-width = <4>;
+	non-removable;
+
+	brcmf: wifi@1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&pio>;
+		interrupts = <10 8>; /* PH10 / EINT10 */
+		interrupt-names = "host-wake";
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt
new file mode 100644
index 000000000..6830c4786
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/esp,esp8089.txt
@@ -0,0 +1,30 @@
+Espressif ESP8089 wireless SDIO devices
+
+This node provides properties for controlling the ESP8089 wireless device.
+The node is expected to be specified as a child node to the SDIO controller
+that connects the device to the system.
+
+Required properties:
+
+ - compatible : Should be "esp,esp8089".
+
+Optional properties:
+ - esp,crystal-26M-en: Integer value for the crystal_26M_en firmware parameter
+
+Example:
+
+&mmc1 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	vmmc-supply = <&reg_dldo1>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+
+	esp8089: sdio_wifi@1 {
+		compatible = "esp,esp8089";
+		reg = <1>;
+		esp,crystal-26M-en = <2>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/ieee80211.txt b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt
new file mode 100644
index 000000000..f6442b139
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/ieee80211.txt
@@ -0,0 +1,24 @@
+Common IEEE 802.11 properties
+
+This provides documentation of common properties that are valid for all wireless
+devices.
+
+Optional properties:
+ - ieee80211-freq-limit : list of supported frequency ranges in KHz. This can be
+	used for devices that in a given config support less channels than
+	normally. It may happen chipset supports a wide wireless band but it is
+	limited to some part of it due to used antennas or power amplifier.
+	An example case for this can be tri-band wireless router with two
+	identical chipsets used for two different 5 GHz subbands. Using them
+	incorrectly could not work or decrease performance noticeably.
+
+Example:
+
+pcie@0,0 {
+	reg = <0x0000 0 0 0 0>;
+	wifi@0,0 {
+		reg = <0x0000 0 0 0 0>;
+		ieee80211-freq-limit = <2402000 2482000>,
+				       <5170000 5250000>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt
new file mode 100644
index 000000000..9bf9bbac1
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/marvell-8xxx.txt
@@ -0,0 +1,68 @@
+Marvell 8787/8897/8997 (sd8787/sd8897/sd8997/pcie8997) SDIO/PCIE devices
+------
+
+This node provides properties for controlling the Marvell SDIO/PCIE wireless device.
+The node is expected to be specified as a child node to the SDIO/PCIE controller that
+connects the device to the system.
+
+Required properties:
+
+  - compatible : should be one of the following:
+	* "marvell,sd8787"
+	* "marvell,sd8897"
+	* "marvell,sd8997"
+	* "pci11ab,2b42"
+	* "pci1b4b,2b42"
+
+Optional properties:
+
+  - marvell,caldata* : A series of properties with marvell,caldata prefix,
+		      represent calibration data downloaded to the device during
+		      initialization. This is an array of unsigned 8-bit values.
+		      the properties should follow below property name and
+		      corresponding array length:
+	"marvell,caldata-txpwrlimit-2g" (length = 566).
+	"marvell,caldata-txpwrlimit-5g-sub0" (length = 502).
+	"marvell,caldata-txpwrlimit-5g-sub1" (length = 688).
+	"marvell,caldata-txpwrlimit-5g-sub2" (length = 750).
+	"marvell,caldata-txpwrlimit-5g-sub3" (length = 502).
+  - marvell,wakeup-pin : a wakeup pin number of wifi chip which will be configured
+		      to firmware. Firmware will wakeup the host using this pin
+		      during suspend/resume.
+  - interrupts : interrupt pin number to the cpu. driver will request an irq based on
+		 this interrupt number. during system suspend, the irq will be enabled
+		 so that the wifi chip can wakeup host platform under certain condition.
+		 during system resume, the irq will be disabled to make sure
+		 unnecessary interrupt is not received.
+  - vmmc-supply: a phandle of a regulator, supplying VCC to the card
+  - mmc-pwrseq:  phandle to the MMC power sequence node. See "mmc-pwrseq-*"
+		 for documentation of MMC power sequence bindings.
+
+Example:
+
+Tx power limit calibration data is configured in below example.
+The calibration data is an array of unsigned values, the length
+can vary between hw versions.
+IRQ pin 38 is used as system wakeup source interrupt. wakeup pin 3 is configured
+so that firmware can wakeup host using this device side pin.
+
+&mmc3 {
+	vmmc-supply = <&wlan_en_reg>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	mwifiex: wifi@1 {
+		compatible = "marvell,sd8897";
+		reg = <1>;
+		interrupt-parent = <&pio>;
+		interrupts = <38 IRQ_TYPE_LEVEL_LOW>;
+
+		marvell,caldata_00_txpwrlimit_2g_cfg_set = /bits/ 8 <
+	0x01 0x00 0x06 0x00 0x08 0x02 0x89 0x01>;
+		marvell,wakeup-pin = <3>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt
new file mode 100644
index 000000000..0c17a0ec9
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/mediatek,mt76.txt
@@ -0,0 +1,32 @@
+* MediaTek mt76xx devices
+
+This node provides properties for configuring the MediaTek mt76xx wireless
+device. The node is expected to be specified as a child node of the PCI
+controller to which the wireless chip is connected.
+
+Optional properties:
+
+- mac-address: See ethernet.txt in the parent directory
+- local-mac-address: See ethernet.txt in the parent directory
+- ieee80211-freq-limit: See ieee80211.txt
+- mediatek,mtd-eeprom: Specify a MTD partition + offset containing EEPROM data
+
+Optional nodes:
+- led: Properties for a connected LED
+  Optional properties:
+    - led-sources: See Documentation/devicetree/bindings/leds/common.txt
+
+&pcie {
+	pcie0 {
+		wifi@0,0 {
+			compatible = "mediatek,mt76";
+			reg = <0x0000 0 0 0 0>;
+			ieee80211-freq-limit = <5000000 6000000>;
+			mediatek,mtd-eeprom = <&factory 0x8000>;
+
+			led {
+				led-sources = <2>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt
new file mode 100644
index 000000000..b7396c8c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/qca,ath9k.txt
@@ -0,0 +1,48 @@
+* Qualcomm Atheros ath9k wireless devices
+
+This node provides properties for configuring the ath9k wireless device. The
+node is expected to be specified as a child node of the PCI controller to
+which the wireless chip is connected.
+
+Required properties:
+- compatible: For PCI and PCIe devices this should be an identifier following
+		the format as defined in "PCI Bus Binding to Open Firmware"
+		Revision 2.1. One of the possible formats is "pciVVVV,DDDD"
+		where VVVV is the PCI vendor ID and DDDD is PCI device ID.
+		Typically QCA's PCI vendor ID 168c is used while the PCI device
+		ID depends on the chipset - see the following (possibly
+		incomplete) list:
+			- 0023 for AR5416
+			- 0024 for AR5418
+			- 0027 for AR9160
+			- 0029 for AR9220 and AR9223
+			- 002a for AR9280 and AR9283
+			- 002b for AR9285
+			- 002c for AR2427
+			- 002d for AR9227
+			- 002e for AR9287
+			- 0030 for AR9380, AR9381 and AR9382
+			- 0032 for AR9485
+			- 0033 for AR9580 and AR9590
+			- 0034 for AR9462
+			- 0036 for AR9565
+			- 0037 for AR9485
+- reg: Address and length of the register set for the device.
+
+Optional properties:
+- qca,no-eeprom: Indicates that there is no physical EEPROM connected to the
+			ath9k wireless chip (in this case the calibration /
+			EEPROM data will be loaded from userspace using the
+			kernel firmware loader).
+- mac-address: See ethernet.txt in the parent directory
+- local-mac-address: See ethernet.txt in the parent directory
+
+
+In this example, the node is defined as child node of the PCI controller:
+&pci0 {
+	wifi@168c,002d {
+		compatible = "pci168c,002d";
+		reg = <0x7000 0 0 0 0x1000>;
+		qca,no-eeprom;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
new file mode 100644
index 000000000..7fd4e8ce4
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
@@ -0,0 +1,152 @@
+* Qualcomm Atheros ath10k wireless devices
+
+Required properties:
+- compatible: Should be one of the following:
+	* "qcom,ath10k"
+	* "qcom,ipq4019-wifi"
+	* "qcom,wcn3990-wifi"
+
+PCI based devices uses compatible string "qcom,ath10k" and takes calibration
+data along with board specific data via "qcom,ath10k-calibration-data".
+Rest of the properties are not applicable for PCI based devices.
+
+AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
+and also uses most of the properties defined in this doc (except
+"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
+to carry pre calibration data.
+
+In general, entry "qcom,ath10k-pre-calibration-data" and
+"qcom,ath10k-calibration-data" conflict with each other and only one
+can be provided per device.
+
+SNOC based devices (i.e. wcn3990) uses compatible string "qcom,wcn3990-wifi".
+
+Optional properties:
+- reg: Address and length of the register set for the device.
+- reg-names: Must include the list of following reg names,
+	     "membase"
+- resets: Must contain an entry for each entry in reset-names.
+          See ../reset/reseti.txt for details.
+- reset-names: Must include the list of following reset names,
+	       "wifi_cpu_init"
+	       "wifi_radio_srif"
+	       "wifi_radio_warm"
+	       "wifi_radio_cold"
+	       "wifi_core_warm"
+	       "wifi_core_cold"
+- clocks: List of clock specifiers, must contain an entry for each required
+          entry in clock-names.
+- clock-names: Should contain the clock names "wifi_wcss_cmd", "wifi_wcss_ref",
+               "wifi_wcss_rtc".
+- interrupts: List of interrupt lines. Must contain an entry
+	      for each entry in the interrupt-names property.
+- interrupt-names: Must include the entries for MSI interrupt
+		   names ("msi0" to "msi15") and legacy interrupt
+		   name ("legacy"),
+- qcom,msi_addr: MSI interrupt address.
+- qcom,msi_base: Base value to add before writing MSI data into
+		MSI address register.
+- qcom,ath10k-calibration-variant: string to search for in the board-2.bin
+				   variant list with the same bus and device
+				   specific ids
+- qcom,ath10k-calibration-data : calibration data + board specific data
+				 as an array, the length can vary between
+				 hw versions.
+- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
+				     the length can vary between hw versions.
+- <supply-name>-supply: handle to the regulator device tree node
+			   optional "supply-name" is "vdd-0.8-cx-mx".
+
+Example (to supply the calibration data alone):
+
+In this example, the node is defined as child node of the PCI controller.
+
+pci {
+	pcie@0 {
+		reg = <0 0 0 0 0>;
+		#interrupt-cells = <1>;
+		#size-cells = <2>;
+		#address-cells = <3>;
+		device_type = "pci";
+
+		ath10k@0,0 {
+			reg = <0 0 0 0 0>;
+			device_type = "pci";
+			qcom,ath10k-calibration-data = [ 01 02 03 ... ];
+		};
+	};
+};
+
+Example (to supply ipq4019 SoC wifi block details):
+
+wifi0: wifi@a000000 {
+	compatible = "qcom,ipq4019-wifi";
+	reg = <0xa000000 0x200000>;
+	resets = <&gcc WIFI0_CPU_INIT_RESET>,
+		 <&gcc WIFI0_RADIO_SRIF_RESET>,
+		 <&gcc WIFI0_RADIO_WARM_RESET>,
+		 <&gcc WIFI0_RADIO_COLD_RESET>,
+		 <&gcc WIFI0_CORE_WARM_RESET>,
+		 <&gcc WIFI0_CORE_COLD_RESET>;
+	reset-names = "wifi_cpu_init",
+		      "wifi_radio_srif",
+		      "wifi_radio_warm",
+		      "wifi_radio_cold",
+		      "wifi_core_warm",
+		      "wifi_core_cold";
+	clocks = <&gcc GCC_WCSS2G_CLK>,
+		 <&gcc GCC_WCSS2G_REF_CLK>,
+		 <&gcc GCC_WCSS2G_RTC_CLK>;
+	clock-names = "wifi_wcss_cmd",
+		      "wifi_wcss_ref",
+		      "wifi_wcss_rtc";
+	interrupts = <0 0x20 0x1>,
+		     <0 0x21 0x1>,
+		     <0 0x22 0x1>,
+		     <0 0x23 0x1>,
+		     <0 0x24 0x1>,
+		     <0 0x25 0x1>,
+		     <0 0x26 0x1>,
+		     <0 0x27 0x1>,
+		     <0 0x28 0x1>,
+		     <0 0x29 0x1>,
+		     <0 0x2a 0x1>,
+		     <0 0x2b 0x1>,
+		     <0 0x2c 0x1>,
+		     <0 0x2d 0x1>,
+		     <0 0x2e 0x1>,
+		     <0 0x2f 0x1>,
+		     <0 0xa8 0x0>;
+	interrupt-names = "msi0",  "msi1",  "msi2",  "msi3",
+			  "msi4",  "msi5",  "msi6",  "msi7",
+			  "msi8",  "msi9",  "msi10", "msi11",
+			  "msi12", "msi13", "msi14", "msi15",
+			  "legacy";
+	qcom,msi_addr = <0x0b006040>;
+	qcom,msi_base = <0x40>;
+	qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
+};
+
+Example (to supply wcn3990 SoC wifi block details):
+
+wifi@18000000 {
+		compatible = "qcom,wcn3990-wifi";
+		reg = <0x18800000 0x800000>;
+		reg-names = "membase";
+		clocks = <&clock_gcc clk_aggre2_noc_clk>;
+		clock-names = "smmu_aggre2_noc_clk"
+		interrupts =
+			   <0 130 0 /* CE0 */ >,
+			   <0 131 0 /* CE1 */ >,
+			   <0 132 0 /* CE2 */ >,
+			   <0 133 0 /* CE3 */ >,
+			   <0 134 0 /* CE4 */ >,
+			   <0 135 0 /* CE5 */ >,
+			   <0 136 0 /* CE6 */ >,
+			   <0 137 0 /* CE7 */ >,
+			   <0 138 0 /* CE8 */ >,
+			   <0 139 0 /* CE9 */ >,
+			   <0 140 0 /* CE10 */ >,
+			   <0 141 0 /* CE11 */ >;
+		vdd-0.8-cx-mx-supply = <&pm8998_l5>;
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt
new file mode 100644
index 000000000..bb2fcde6f
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wl1251.txt
@@ -0,0 +1,37 @@
+* Texas Instruments wl1251 wireless lan controller
+
+The wl1251 chip can be connected via SPI or via SDIO. This
+document describes the binding for the SPI connected chip.
+
+Required properties:
+- compatible :        Should be "ti,wl1251"
+- reg :               Chip select address of device
+- spi-max-frequency : Maximum SPI clocking speed of device in Hz
+- interrupts :        Should contain interrupt line
+- vio-supply :        phandle to regulator providing VIO
+- ti,power-gpio :     GPIO connected to chip's PMEN pin
+
+Optional properties:
+- ti,wl1251-has-eeprom : boolean, the wl1251 has an eeprom connected, which
+                         provides configuration data (calibration, MAC, ...)
+- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
+  for optional SPI connection related properties,
+
+Examples:
+
+&spi1 {
+	wl1251@0 {
+		compatible = "ti,wl1251";
+
+		reg = <0>;
+		spi-max-frequency = <48000000>;
+		spi-cpol;
+		spi-cpha;
+
+		interrupt-parent = <&gpio2>;
+		interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
+
+		vio-supply = <&vio>;
+		ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
new file mode 100644
index 000000000..cb5c9e156
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore,spi.txt
@@ -0,0 +1,57 @@
+* Texas Instruments wl12xx/wl18xx wireless lan controller
+
+The wl12xx/wl18xx chips can be connected via SPI or via SDIO. This
+document describes the binding for the SPI connected chip.
+
+Required properties:
+- compatible :          Should be one of the following:
+    * "ti,wl1271"
+    * "ti,wl1273"
+    * "ti,wl1281"
+    * "ti,wl1283"
+    * "ti,wl1801"
+    * "ti,wl1805"
+    * "ti,wl1807"
+    * "ti,wl1831"
+    * "ti,wl1835"
+    * "ti,wl1837"
+- reg :                 Chip select address of device
+- spi-max-frequency :   Maximum SPI clocking speed of device in Hz
+- interrupts :          Should contain parameters for 1 interrupt line.
+- vwlan-supply :        Point the node of the regulator that powers/enable the
+                        wl12xx/wl18xx chip
+
+Optional properties:
+- ref-clock-frequency : Reference clock frequency (should be set for wl12xx)
+- clock-xtal :          boolean, clock is generated from XTAL
+
+- Please consult Documentation/devicetree/bindings/spi/spi-bus.txt
+  for optional SPI connection related properties,
+
+Examples:
+
+For wl12xx family:
+&spi1 {
+	wlcore: wlcore@1 {
+		compatible = "ti,wl1271";
+		reg = <1>;
+		spi-max-frequency = <48000000>;
+		interrupt-parent = <&gpio3>;
+		interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+		vwlan-supply = <&vwlan_fixed>;
+		clock-xtal;
+		ref-clock-frequency = <38400000>;
+	};
+};
+
+For wl18xx family:
+&spi0 {
+	wlcore: wlcore@0 {
+		compatible = "ti,wl1835";
+		reg = <0>;
+		spi-max-frequency = <48000000>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+		vwlan-supply = <&vwlan_fixed>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
new file mode 100644
index 000000000..9306c4dad
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/wireless/ti,wlcore.txt
@@ -0,0 +1,45 @@
+TI Wilink 6/7/8 (wl12xx/wl18xx) SDIO devices
+
+This node provides properties for controlling the wilink wireless device. The
+node is expected to be specified as a child node to the SDIO controller that
+connects the device to the system.
+
+Required properties:
+ - compatible: should be one of the following:
+    * "ti,wl1271"
+    * "ti,wl1273"
+    * "ti,wl1281"
+    * "ti,wl1283"
+    * "ti,wl1285"
+    * "ti,wl1801"
+    * "ti,wl1805"
+    * "ti,wl1807"
+    * "ti,wl1831"
+    * "ti,wl1835"
+    * "ti,wl1837"
+ - interrupts : specifies attributes for the out-of-band interrupt.
+
+Optional properties:
+ - ref-clock-frequency : ref clock frequency in Hz
+ - tcxo-clock-frequency : tcxo clock frequency in Hz
+
+Note: the *-clock-frequency properties assume internal clocks. In case of external
+clock, new bindings (for parsing the clock nodes) have to be added.
+
+Example:
+
+&mmc3 {
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	cap-power-off-card;
+	keep-power-in-suspend;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <19 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};