Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 674 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
new file mode 100644
index 000000000..145a4f041
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
@@ -0,0 +1,674 @@
+NVIDIA Tegra PCIe controller
+
+Required properties:
+- compatible: Must be:
+  - "nvidia,tegra20-pcie": for Tegra20
+  - "nvidia,tegra30-pcie": for Tegra30
+  - "nvidia,tegra124-pcie": for Tegra124 and Tegra132
+  - "nvidia,tegra210-pcie": for Tegra210
+  - "nvidia,tegra186-pcie": for Tegra186
+- power-domains: To ungate power partition by BPMP powergate driver. Must
+  contain BPMP phandle and PCIe power partition ID. This is required only
+  for Tegra186.
+- device_type: Must be "pci"
+- reg: A list of physical base address and length for each set of controller
+  registers. Must contain an entry for each entry in the reg-names property.
+- reg-names: Must include the following entries:
+  "pads": PADS registers
+  "afi": AFI registers
+  "cs": configuration space region
+- interrupts: A list of interrupt outputs of the controller. Must contain an
+  entry for each entry in the interrupt-names property.
+- interrupt-names: Must include the following entries:
+  "intr": The Tegra interrupt that is asserted for controller interrupts
+  "msi": The Tegra interrupt that is asserted when an MSI is received
+- bus-range: Range of bus numbers associated with this controller
+- #address-cells: Address representation for root ports (must be 3)
+  - cell 0 specifies the bus and device numbers of the root port:
+    [23:16]: bus number
+    [15:11]: device number
+  - cell 1 denotes the upper 32 address bits and should be 0
+  - cell 2 contains the lower 32 address bits and is used to translate to the
+    CPU address space
+- #size-cells: Size representation for root ports (must be 2)
+- ranges: Describes the translation of addresses for root ports and standard
+  PCI regions. The entries must be 6 cells each, where the first three cells
+  correspond to the address as described for the #address-cells property
+  above, the fourth cell is the physical CPU address to translate to and the
+  fifth and six cells are as described for the #size-cells property above.
+  - The first two entries are expected to translate the addresses for the root
+    port registers, which are referenced by the assigned-addresses property of
+    the root port nodes (see below).
+  - The remaining entries setup the mapping for the standard I/O, memory and
+    prefetchable PCI regions. The first cell determines the type of region
+    that is setup:
+    - 0x81000000: I/O memory region
+    - 0x82000000: non-prefetchable memory region
+    - 0xc2000000: prefetchable memory region
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
+- #interrupt-cells: Size representation for interrupts (must be 1)
+- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties
+  Please refer to the standard PCI bus binding document for a more detailed
+  explanation.
+- clocks: Must contain an entry for each entry in clock-names.
+  See ../clocks/clock-bindings.txt for details.
+- clock-names: Must include the following entries:
+  - pex
+  - afi
+  - pll_e
+  - cml (not required for Tegra20)
+- resets: Must contain an entry for each entry in reset-names.
+  See ../reset/reset.txt for details.
+- reset-names: Must include the following entries:
+  - pex
+  - afi
+  - pcie_x
+
+Required properties on Tegra124 and later (deprecated):
+- phys: Must contain an entry for each entry in phy-names.
+- phy-names: Must include the following entries:
+  - pcie
+
+These properties are deprecated in favour of per-lane PHYs define in each of
+the root ports (see below).
+
+Power supplies for Tegra20:
+- avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
+- vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+- avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
+  supply 1.05 V.
+- avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must
+  supply 1.05 V.
+- vddio-pex-clk-supply: Power supply for PCIe clock. Must supply 3.3 V.
+
+Power supplies for Tegra30:
+- Required:
+  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
+    supply 1.05 V.
+  - avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must
+    supply 1.05 V.
+  - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
+    supply 1.8 V.
+  - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
+    Must supply 3.3 V.
+- Optional:
+  - If lanes 0 to 3 are used:
+    - avdd-pexa-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
+    - vdd-pexa-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+  - If lanes 4 or 5 are used:
+    - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
+    - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+
+Power supplies for Tegra124:
+- Required:
+  - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V.
+  - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+  - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
+    supply 1.05 V.
+  - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
+    Must supply 3.3 V.
+  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
+    Must supply 3.3 V.
+  - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
+    supply 2.8-3.3 V.
+  - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must
+    supply 1.05 V.
+
+Power supplies for Tegra210:
+- Required:
+  - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must
+    supply 1.05 V.
+  - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output
+    clocks. Must supply 1.8 V.
+  - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+  - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must
+    supply 1.05 V.
+  - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3).
+    Must supply 3.3 V.
+  - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
+    supply 1.8 V.
+
+Power supplies for Tegra186:
+- Required:
+  - dvdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+  - hvdd-pex-pll-supply: High-voltage supply for PLLE (shared with USB3). Must
+    supply 1.8 V.
+  - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
+    Must supply 1.8 V.
+  - vddio-pexctl-aud-supply: Power supply for PCIe side band signals. Must
+    supply 1.8 V.
+
+Root ports are defined as subnodes of the PCIe controller node.
+
+Required properties:
+- device_type: Must be "pci"
+- assigned-addresses: Address and size of the port configuration registers
+- reg: PCI bus address of the root port
+- #address-cells: Must be 3
+- #size-cells: Must be 2
+- ranges: Sub-ranges distributed from the PCIe controller node. An empty
+  property is sufficient.
+- nvidia,num-lanes: Number of lanes to use for this port. Valid combinations
+  are:
+  - Root port 0 uses 4 lanes, root port 1 is unused.
+  - Both root ports use 2 lanes.
+
+Required properties for Tegra124 and later:
+- phys: Must contain an phandle to a PHY for each entry in phy-names.
+- phy-names: Must include an entry for each active lane. Note that the number
+  of entries does not have to (though usually will) be equal to the specified
+  number of lanes in the nvidia,num-lanes property. Entries are of the form
+  "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes.
+
+Examples:
+=========
+
+Tegra20:
+--------
+
+SoC DTSI:
+
+	pcie-controller@80003000 {
+		compatible = "nvidia,tegra20-pcie";
+		device_type = "pci";
+		reg = <0x80003000 0x00000800   /* PADS registers */
+		       0x80003800 0x00000200   /* AFI registers */
+		       0x90000000 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+		interrupts = <0 98 0x04   /* controller interrupt */
+		              0 99 0x04>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000   /* port 0 registers */
+			  0x82000000 0 0x80001000 0x80001000 0 0x00001000   /* port 1 registers */
+			  0x81000000 0 0          0x82000000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0xa0000000 0xa0000000 0 0x10000000   /* non-prefetchable memory */
+			  0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */
+
+		clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 118>;
+		clock-names = "pex", "afi", "pll_e";
+		resets = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>;
+		reset-names = "pex", "afi", "pcie_x";
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+	};
+
+Board DTS:
+
+	pcie-controller@80003000 {
+		status = "okay";
+
+		vdd-supply = <&pci_vdd_reg>;
+		pex-clk-supply = <&pci_clk_reg>;
+
+		/* root port 00:01.0 */
+		pci@1,0 {
+			status = "okay";
+
+			/* bridge 01:00.0 (optional) */
+			pci@0,0 {
+				reg = <0x010000 0 0 0 0>;
+
+				#address-cells = <3>;
+				#size-cells = <2>;
+
+				device_type = "pci";
+
+				/* endpoint 02:00.0 */
+				pci@0,0 {
+					reg = <0x020000 0 0 0 0>;
+				};
+			};
+		};
+	};
+
+Note that devices on the PCI bus are dynamically discovered using PCI's bus
+enumeration and therefore don't need corresponding device nodes in DT. However
+if a device on the PCI bus provides a non-probeable bus such as I2C or SPI,
+device nodes need to be added in order to allow the bus' children to be
+instantiated at the proper location in the operating system's device tree (as
+illustrated by the optional nodes in the example above).
+
+Tegra30:
+--------
+
+SoC DTSI:
+
+	pcie-controller@3000 {
+		compatible = "nvidia,tegra30-pcie";
+		device_type = "pci";
+		reg = <0x00003000 0x00000800   /* PADS registers */
+		       0x00003800 0x00000200   /* AFI registers */
+		       0x10000000 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH   /* controller interrupt */
+			      GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000   /* port 0 configuration space */
+			  0x82000000 0 0x00001000 0x00001000 0 0x00001000   /* port 1 configuration space */
+			  0x82000000 0 0x00004000 0x00004000 0 0x00001000   /* port 2 configuration space */
+			  0x81000000 0 0          0x02000000 0 0x00010000   /* downstream I/O */
+			  0x82000000 0 0x20000000 0x20000000 0 0x08000000   /* non-prefetchable memory */
+			  0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */
+
+		clocks = <&tegra_car TEGRA30_CLK_PCIE>,
+			 <&tegra_car TEGRA30_CLK_AFI>,
+			 <&tegra_car TEGRA30_CLK_PLL_E>,
+			 <&tegra_car TEGRA30_CLK_CML0>;
+		clock-names = "pex", "afi", "pll_e", "cml";
+		resets = <&tegra_car 70>,
+			 <&tegra_car 72>,
+			 <&tegra_car 74>;
+		reset-names = "pex", "afi", "pcie_x";
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x00000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x00001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@3,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001800 0 0x00004000 0 0x1000>;
+			reg = <0x001800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+	};
+
+Board DTS:
+
+	pcie-controller@3000 {
+		status = "okay";
+
+		avdd-pexa-supply = <&ldo1_reg>;
+		vdd-pexa-supply = <&ldo1_reg>;
+		avdd-pexb-supply = <&ldo1_reg>;
+		vdd-pexb-supply = <&ldo1_reg>;
+		avdd-pex-pll-supply = <&ldo1_reg>;
+		avdd-plle-supply = <&ldo1_reg>;
+		vddio-pex-ctl-supply = <&sys_3v3_reg>;
+		hvdd-pex-supply = <&sys_3v3_pexs_reg>;
+
+		pci@1,0 {
+			status = "okay";
+		};
+
+		pci@3,0 {
+			status = "okay";
+		};
+	};
+
+Tegra124:
+---------
+
+SoC DTSI:
+
+	pcie-controller@1003000 {
+		compatible = "nvidia,tegra124-pcie";
+		device_type = "pci";
+		reg = <0x0 0x01003000 0x0 0x00000800   /* PADS registers */
+		       0x0 0x01003800 0x0 0x00000800   /* AFI registers */
+		       0x0 0x02000000 0x0 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000   /* port 0 configuration space */
+			  0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000   /* port 1 configuration space */
+			  0x81000000 0 0x0        0x0 0x12000000 0 0x00010000   /* downstream I/O (64 KiB) */
+			  0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000   /* non-prefetchable memory (208 MiB) */
+			  0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */
+
+		clocks = <&tegra_car TEGRA124_CLK_PCIE>,
+			 <&tegra_car TEGRA124_CLK_AFI>,
+			 <&tegra_car TEGRA124_CLK_PLL_E>,
+			 <&tegra_car TEGRA124_CLK_CML0>;
+		clock-names = "pex", "afi", "pll_e", "cml";
+		resets = <&tegra_car 70>,
+			 <&tegra_car 72>,
+			 <&tegra_car 74>;
+		reset-names = "pex", "afi", "pcie_x";
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <1>;
+		};
+	};
+
+Board DTS:
+
+	pcie-controller@1003000 {
+		status = "okay";
+
+		avddio-pex-supply = <&vdd_1v05_run>;
+		dvddio-pex-supply = <&vdd_1v05_run>;
+		avdd-pex-pll-supply = <&vdd_1v05_run>;
+		hvdd-pex-supply = <&vdd_3v3_lp0>;
+		hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>;
+		vddio-pex-ctl-supply = <&vdd_3v3_lp0>;
+		avdd-pll-erefe-supply = <&avdd_1v05_run>;
+
+		/* Mini PCIe */
+		pci@1,0 {
+			phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>;
+			phy-names = "pcie-0";
+			status = "okay";
+		};
+
+		/* Gigabit Ethernet */
+		pci@2,0 {
+			phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>;
+			phy-names = "pcie-0";
+			status = "okay";
+		};
+	};
+
+Tegra210:
+---------
+
+SoC DTSI:
+
+	pcie-controller@1003000 {
+		compatible = "nvidia,tegra210-pcie";
+		device_type = "pci";
+		reg = <0x0 0x01003000 0x0 0x00000800   /* PADS registers */
+		       0x0 0x01003800 0x0 0x00000800   /* AFI registers */
+		       0x0 0x02000000 0x0 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+		interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000   /* port 0 configuration space */
+			  0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000   /* port 1 configuration space */
+			  0x81000000 0 0x0        0x0 0x12000000 0 0x00010000   /* downstream I/O (64 KiB) */
+			  0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000   /* non-prefetchable memory (208 MiB) */
+			  0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */
+
+		clocks = <&tegra_car TEGRA210_CLK_PCIE>,
+			 <&tegra_car TEGRA210_CLK_AFI>,
+			 <&tegra_car TEGRA210_CLK_PLL_E>,
+			 <&tegra_car TEGRA210_CLK_CML0>;
+		clock-names = "pex", "afi", "pll_e", "cml";
+		resets = <&tegra_car 70>,
+			 <&tegra_car 72>,
+			 <&tegra_car 74>;
+		reset-names = "pex", "afi", "pcie_x";
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <4>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <1>;
+		};
+	};
+
+Board DTS:
+
+	pcie-controller@1003000 {
+		status = "okay";
+
+		avdd-pll-uerefe-supply = <&avdd_1v05_pll>;
+		hvddio-pex-supply = <&vdd_1v8>;
+		dvddio-pex-supply = <&vdd_pex_1v05>;
+		dvdd-pex-pll-supply = <&vdd_pex_1v05>;
+		hvdd-pex-pll-e-supply = <&vdd_1v8>;
+		vddio-pex-ctl-supply = <&vdd_1v8>;
+
+		pci@1,0 {
+			phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>,
+			       <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>,
+			       <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>,
+			       <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>;
+			phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3";
+			status = "okay";
+		};
+
+		pci@2,0 {
+			phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>;
+			phy-names = "pcie-0";
+			status = "okay";
+		};
+	};
+
+Tegra186:
+---------
+
+SoC DTSI:
+
+	pcie@10003000 {
+		compatible = "nvidia,tegra186-pcie";
+		power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>;
+		device_type = "pci";
+		reg = <0x0 0x10003000 0x0 0x00000800   /* PADS registers */
+		       0x0 0x10003800 0x0 0x00000800   /* AFI registers */
+		       0x0 0x40000000 0x0 0x10000000>; /* configuration space */
+		reg-names = "pads", "afi", "cs";
+
+		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+			     <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+		interrupt-names = "intr", "msi";
+
+		#interrupt-cells = <1>;
+		interrupt-map-mask = <0 0 0 0>;
+		interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+		bus-range = <0x00 0xff>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000   /* port 0 configuration space */
+			  0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000   /* port 1 configuration space */
+			  0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000   /* port 2 configuration space */
+			  0x81000000 0 0x0        0x0 0x50000000 0 0x00010000   /* downstream I/O (64 KiB) */
+			  0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000   /* non-prefetchable memory (127 MiB) */
+			  0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */
+
+		clocks = <&bpmp TEGRA186_CLK_AFI>,
+			 <&bpmp TEGRA186_CLK_PCIE>,
+			 <&bpmp TEGRA186_CLK_PLLE>;
+		clock-names = "afi", "pex", "pll_e";
+
+		resets = <&bpmp TEGRA186_RESET_AFI>,
+			 <&bpmp TEGRA186_RESET_PCIE>,
+			 <&bpmp TEGRA186_RESET_PCIEXCLK>;
+		reset-names = "afi", "pex", "pcie_x";
+
+		status = "disabled";
+
+		pci@1,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>;
+			reg = <0x000800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <2>;
+		};
+
+		pci@2,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>;
+			reg = <0x001000 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <1>;
+		};
+
+		pci@3,0 {
+			device_type = "pci";
+			assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>;
+			reg = <0x001800 0 0 0 0>;
+			status = "disabled";
+
+			#address-cells = <3>;
+			#size-cells = <2>;
+			ranges;
+
+			nvidia,num-lanes = <1>;
+		};
+	};
+
+Board DTS:
+
+	pcie@10003000 {
+		status = "okay";
+
+		dvdd-pex-supply = <&vdd_pex>;
+		hvdd-pex-pll-supply = <&vdd_1v8>;
+		hvdd-pex-supply = <&vdd_1v8>;
+		vddio-pexctl-aud-supply = <&vdd_1v8>;
+
+		pci@1,0 {
+			nvidia,num-lanes = <4>;
+			status = "okay";
+		};
+
+		pci@2,0 {
+			nvidia,num-lanes = <0>;
+			status = "disabled";
+		};
+
+		pci@3,0 {
+			nvidia,num-lanes = <1>;
+			status = "disabled";
+		};
+	};