Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

43 files changed, 1556 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt
new file mode 100644
index 000000000..f181e46d8
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/ab8500/btemp.txt
@@ -0,0 +1,16 @@
+=== AB8500 Battery Temperature Monitor Driver ===
+
+The properties below describes the node for btemp driver.
+
+Required Properties:
+- compatible = Shall be: "stericsson,ab8500-btemp"
+- battery = Shall be battery specific information
+
+	Example:
+	ab8500_btemp {
+		compatible = "stericsson,ab8500-btemp";
+		battery	   = <&ab8500_battery>;
+	};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power/supply/ab8500/fg.txt
diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt
new file mode 100644
index 000000000..56636f927
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/ab8500/chargalg.txt
@@ -0,0 +1,16 @@
+=== AB8500 Charging Algorithm Driver ===
+
+The properties below describes the node for chargalg driver.
+
+Required Properties:
+- compatible = Shall be: "stericsson,ab8500-chargalg"
+- battery = Shall be battery specific information
+
+Example:
+ab8500_chargalg {
+	compatible = "stericsson,ab8500-chargalg";
+	battery	   = <&ab8500_battery>;
+};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power/supply/ab8500/fg.txt
diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt
new file mode 100644
index 000000000..24ada03e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/ab8500/charger.txt
@@ -0,0 +1,25 @@
+=== AB8500 Charger Driver ===
+
+Required Properties:
+- compatible = Shall be "stericsson,ab8500-charger"
+- battery = Shall be battery specific information
+	Example:
+	ab8500_charger {
+		compatible = "stericsson,ab8500-charger";
+		battery	   = <&ab8500_battery>;
+	};
+
+- vddadc-supply: Supply for USB and Main charger
+	Example:
+	ab8500-charger {
+		vddadc-supply	= <&ab8500_ldo_tvout_reg>;
+	}
+- autopower_cfg:
+	Boolean value depicting the presence of 'automatic poweron after powerloss'
+	Example:
+	ab8500-charger {
+		autopower_cfg;
+	};
+
+For information on battery specific node, Ref:
+Documentation/devicetree/bindings/power/supply/ab8500/fg.txt
diff --git a/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt
new file mode 100644
index 000000000..ccafcb911
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/ab8500/fg.txt
@@ -0,0 +1,58 @@
+=== AB8500 Fuel Gauge Driver ===
+
+AB8500 is a mixed signal multimedia and power management
+device comprising: power and energy-management-module,
+wall-charger, usb-charger, audio codec, general purpose adc,
+tvout, clock management and sim card interface.
+
+Fuelgauge support is part of energy-management-modules, other
+components of this module are:
+main-charger, usb-combo-charger and battery-temperature-monitoring.
+
+The properties below describes the node for fuelgauge driver.
+
+Required Properties:
+- compatible = This shall be: "stericsson,ab8500-fg"
+- battery = Shall be battery specific information
+	Example:
+	ab8500_fg {
+		compatible = "stericsson,ab8500-fg";
+		battery	   = <&ab8500_battery>;
+	};
+
+dependent node:
+	ab8500_battery: ab8500_battery {
+	};
+	This node will provide information on 'thermistor interface' and
+	'battery technology type' used.
+
+Properties of this node are:
+thermistor-on-batctrl:
+	A boolean value indicating thermistor interface	to battery
+
+	Note:
+	'btemp' and 'batctrl' are the pins interfaced for battery temperature
+	measurement, 'btemp' signal is used when NTC(negative temperature
+	coefficient) resister is interfaced external to battery whereas
+	'batctrl' pin is used when NTC resister is internal to battery.
+
+	Example:
+	ab8500_battery: ab8500_battery {
+		thermistor-on-batctrl;
+	};
+	indicates: NTC resister is internal to battery, 'batctrl' is used
+		for thermal measurement.
+
+	The absence of property 'thermal-on-batctrl' indicates
+	NTC resister is external to battery and  'btemp' signal is used
+	for thermal measurement.
+
+battery-type:
+	This shall be the battery manufacturing technology type,
+	allowed types are:
+		"UNKNOWN" "NiMH" "LION" "LIPO" "LiFe" "NiCd" "LiMn"
+	Example:
+	ab8500_battery: ab8500_battery {
+		stericsson,battery-type = "LIPO";
+	}
+
diff --git a/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt
new file mode 100644
index 000000000..c7dfb7cec
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/act8945a-charger.txt
@@ -0,0 +1,44 @@
+Device-Tree bindings for charger of Active-semi ACT8945A Multi-Function Device
+
+Required properties:
+ - compatible: "active-semi,act8945a-charger".
+ - active-semi,chglev-gpios: charge current level phandle with args
+   as described in ../gpio/gpio.txt.
+ - active-semi,lbo-gpios: specify the low battery voltage detect phandle
+   with args as as described in ../gpio/gpio.txt.
+ - interrupts: <a b> where a is the interrupt number and b is a
+   field that represents an encoding of the sense and level
+   information for the interrupt.
+
+Optional properties:
+ - active-semi,input-voltage-threshold-microvolt: unit: mV;
+   Specifies the charger's input over-voltage threshold value;
+   The value can be: 6600, 7000, 7500, 8000; default: 6600
+ - active-semi,precondition-timeout: unit: minutes;
+   Specifies the charger's PRECONDITION safety timer setting value;
+   The value can be: 40, 60, 80, 0; If 0, it means to disable this timer;
+   default: 40.
+ - active-semi,total-timeout: unit: hours;
+   Specifies the charger's total safety timer setting value;
+   The value can be: 3, 4, 5, 0; If 0, it means to disable this timer;
+   default: 3.
+
+Example:
+	pmic@5b {
+		compatible = "active-semi,act8945a";
+		reg = <0x5b>;
+
+		charger {
+			compatible = "active-semi,act8945a-charger";
+			pinctrl-names = "default";
+			pinctrl-0 = <&pinctrl_charger_chglev &pinctrl_charger_lbo &pinctrl_charger_irq>;
+			interrupt-parent = <&pioA>;
+			interrupts = <45 GPIO_ACTIVE_LOW>;
+
+			active-semi,chglev-gpios = <&pioA 12 GPIO_ACTIVE_HIGH>;
+			active-semi,lbo-gpios = <&pioA 72 GPIO_ACTIVE_LOW>;
+			active-semi,input-voltage-threshold-microvolt = <6600>;
+			active-semi,precondition-timeout = <40>;
+			active-semi,total-timeout = <3>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt
new file mode 100644
index 000000000..826e8a879
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/axp20x_ac_power.txt
@@ -0,0 +1,22 @@
+AXP20X and AXP22X PMICs' AC power supply
+
+Required Properties:
+ - compatible: One of:
+			"x-powers,axp202-ac-power-supply"
+			"x-powers,axp221-ac-power-supply"
+
+This node is a subnode of the axp20x PMIC.
+
+The AXP20X can read the current current and voltage supplied by AC by
+reading ADC channels from the AXP20X ADC.
+
+The AXP22X is only able to tell if an AC power supply is present and
+usable.
+
+Example:
+
+&axp209 {
+	ac_power_supply: ac-power-supply {
+		compatible = "x-powers,axp202-ac-power-supply";
+	};
+};
diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt
new file mode 100644
index 000000000..41916f699
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/axp20x_battery.txt
@@ -0,0 +1,20 @@
+AXP20x and AXP22x battery power supply
+
+Required Properties:
+ - compatible, one of:
+			"x-powers,axp209-battery-power-supply"
+			"x-powers,axp221-battery-power-supply"
+			"x-powers,axp813-battery-power-supply"
+
+This node is a subnode of its respective PMIC DT node.
+
+The supported devices can read the battery voltage, charge and discharge
+currents of the battery by reading ADC channels from the ADC.
+
+Example:
+
+&axp209 {
+	battery_power_supply: battery-power-supply {
+		compatible = "x-powers,axp209-battery-power-supply";
+	}
+};
diff --git a/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt
new file mode 100644
index 000000000..ba8d35f66
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/axp20x_usb_power.txt
@@ -0,0 +1,40 @@
+AXP20x USB power supply
+
+Required Properties:
+-compatible: One of: "x-powers,axp202-usb-power-supply"
+                     "x-powers,axp221-usb-power-supply"
+                     "x-powers,axp223-usb-power-supply"
+
+The AXP223 PMIC shares most of its behaviour with the AXP221 but has slight
+variations such as the former being able to set the VBUS power supply max
+current to 100mA, unlike the latter.
+
+This node is a subnode of the axp20x PMIC.
+
+Example:
+
+axp209: pmic@34 {
+	compatible = "x-powers,axp209";
+	reg = <0x34>;
+	interrupt-parent = <&nmi_intc>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+	interrupt-controller;
+	#interrupt-cells = <1>;
+
+	regulators {
+		x-powers,dcdc-freq = <1500>;
+
+		vdd_cpu: dcdc2 {
+			regulator-always-on;
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1450000>;
+			regulator-name = "vdd-cpu";
+		};
+
+		...
+	};
+
+	usb-power-supply: usb-power-supply {
+		compatible = "x-powers,axp202-usb-power-supply";
+	};
+};
diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt
new file mode 100644
index 000000000..f4d3b4a10
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/battery.txt
@@ -0,0 +1,57 @@
+Battery Characteristics
+
+The devicetree battery node provides static battery characteristics.
+In smart batteries, these are typically stored in non-volatile memory
+on a fuel gauge chip. The battery node should be used where there is
+no appropriate non-volatile memory, or it is unprogrammed/incorrect.
+
+Upstream dts files should not include battery nodes, unless the battery
+represented cannot easily be replaced in the system by one of a
+different type. This prevents unpredictable, potentially harmful,
+behavior should a replacement that changes the battery type occur
+without a corresponding update to the dtb.
+
+Required Properties:
+ - compatible: Must be "simple-battery"
+
+Optional Properties:
+ - voltage-min-design-microvolt: drained battery voltage
+ - energy-full-design-microwatt-hours: battery design energy
+ - charge-full-design-microamp-hours: battery design capacity
+ - precharge-current-microamp: current for pre-charge phase
+ - charge-term-current-microamp: current for charge termination phase
+ - constant-charge-current-max-microamp: maximum constant input current
+ - constant-charge-voltage-max-microvolt: maximum constant input voltage
+
+Battery properties are named, where possible, for the corresponding
+elements in enum power_supply_property, defined in
+https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h
+
+Batteries must be referenced by chargers and/or fuel-gauges
+using a phandle. The phandle's property should be named
+"monitored-battery".
+
+Example:
+
+	bat: battery {
+		compatible = "simple-battery";
+		voltage-min-design-microvolt = <3200000>;
+		energy-full-design-microwatt-hours = <5290000>;
+		charge-full-design-microamp-hours = <1430000>;
+		precharge-current-microamp = <256000>;
+		charge-term-current-microamp = <128000>;
+		constant-charge-current-max-microamp = <900000>;
+		constant-charge-voltage-max-microvolt = <4200000>;
+	};
+
+	charger: charger@11 {
+		....
+		monitored-battery = <&bat>;
+		...
+	};
+
+	fuel_gauge: fuel-gauge@22 {
+		....
+		monitored-battery = <&bat>;
+		...
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/bq2415x.txt b/Documentation/devicetree/bindings/power/supply/bq2415x.txt
new file mode 100644
index 000000000..d0327f0b5
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq2415x.txt
@@ -0,0 +1,47 @@
+Binding for TI bq2415x Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24150"
+ * "ti,bq24150"
+ * "ti,bq24150a"
+ * "ti,bq24151"
+ * "ti,bq24151a"
+ * "ti,bq24152"
+ * "ti,bq24153"
+ * "ti,bq24153a"
+ * "ti,bq24155"
+ * "ti,bq24156"
+ * "ti,bq24156a"
+ * "ti,bq24158"
+- reg:			   integer, i2c address of the device.
+- ti,current-limit:	   integer, initial maximum current charger can pull
+			   from power supply in mA.
+- ti,weak-battery-voltage: integer, weak battery voltage threshold in mV.
+			   The chip will use slow precharge if battery voltage
+			   is below this value.
+- ti,battery-regulation-voltage: integer, maximum charging voltage in mV.
+- ti,charge-current:	   integer, maximum charging current in mA.
+- ti,termination-current:  integer, charge will be terminated when current in
+			   constant-voltage phase drops below this value (in mA).
+- ti,resistor-sense:	   integer, value of sensing resistor in milliohm.
+
+Optional properties:
+- ti,usb-charger-detection: phandle to usb charger detection device.
+			    (required for auto mode)
+
+Example from Nokia N900:
+
+bq24150a {
+	compatible = "ti,bq24150a";
+	reg = <0x6b>;
+
+	ti,current-limit = <100>;
+	ti,weak-battery-voltage = <3400>;
+	ti,battery-regulation-voltage = <4200>;
+	ti,charge-current = <650>;
+	ti,termination-current = <100>;
+	ti,resistor-sense = <68>;
+
+	ti,usb-charger-detection = <&isp1704>;
+};
diff --git a/Documentation/devicetree/bindings/power/supply/bq24190.txt b/Documentation/devicetree/bindings/power/supply/bq24190.txt
new file mode 100644
index 000000000..9e517d307
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq24190.txt
@@ -0,0 +1,51 @@
+TI BQ24190 Li-Ion Battery Charger
+
+Required properties:
+- compatible: contains one of the following:
+    * "ti,bq24190"
+    * "ti,bq24192i"
+- reg: integer, I2C address of the charger.
+- interrupts[-extended]: configuration for charger INT pin.
+
+Optional properties:
+- monitored-battery: phandle of battery characteristics devicetree node
+  The charger uses the following battery properties:
+    + precharge-current-microamp: maximum charge current during precharge
+      phase (typically 20% of battery capacity).
+    + charge-term-current-microamp: a charge cycle terminates when the
+      battery voltage is above recharge threshold, and the current is below
+      this setting (typically 10% of battery capacity).
+  See also Documentation/devicetree/bindings/power/supply/battery.txt
+- ti,system-minimum-microvolt: when power is connected and the battery is below
+  minimum system voltage, the system will be regulated above this setting.
+
+Notes:
+- Some circuit boards wire the chip's "OTG" pin high (enabling 500mA default
+  charge current on USB SDP ports, among other features). To simulate this on
+  boards that wire the pin to a GPIO, set a gpio-hog.
+
+Example:
+
+	bat: battery {
+		compatible = "simple-battery";
+		precharge-current-microamp = <256000>;
+		charge-term-current-microamp = <128000>;
+		// etc.
+	};
+
+	bq24190: charger@6a {
+		compatible = "ti,bq24190";
+		reg = <0x6a>;
+		interrupts-extended = <&gpiochip 10 IRQ_TYPE_EDGE_FALLING>;
+		monitored-battery = <&bat>;
+		ti,system-minimum-microvolt = <3200000>;
+	};
+
+	&twl_gpio {
+		otg {
+			gpio-hog;
+			gpios = <6 0>;
+			output-high;
+			line-name = "otg-gpio";
+		};
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/bq24257.txt b/Documentation/devicetree/bindings/power/supply/bq24257.txt
new file mode 100644
index 000000000..f8f5a1685
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq24257.txt
@@ -0,0 +1,62 @@
+Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "ti,bq24250"
+ * "ti,bq24251"
+ * "ti,bq24257"
+- reg: integer, i2c address of the device.
+- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in
+    conjunction with "interrupt-parent".
+- ti,battery-regulation-voltage: integer, maximum charging voltage in uV.
+- ti,charge-current: integer, maximum charging current in uA.
+- ti,termination-current: integer, charge will be terminated when current in
+    constant-voltage phase drops below this value (in uA).
+
+Optional properties:
+- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin.
+    This pin is not available on all devices however it should be used if
+    possible as this is the recommended way to obtain the charger's input PG
+    state. If this pin is not specified a software-based approach for PG
+    detection is used.
+- ti,current-limit: The maximum current to be drawn from the charger's input
+    (in uA). If this property is not specified, the input limit current is
+    set automatically using USB D+/D- signal based charger type detection.
+    If the hardware does not support the D+/D- based detection, a default
+    of 500,000 is used (=500mA) instead.
+- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If
+    not specified a default of 6,5000,000 (=6.5V) is used.
+- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic
+    power path management (in uV). If not specified a default of 4,360,000
+    (=4.36V) is used.
+
+Example:
+
+bq24257 {
+	compatible = "ti,bq24257";
+	reg = <0x6a>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+	pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+
+	ti,battery-regulation-voltage = <4200000>;
+	ti,charge-current = <1000000>;
+	ti,termination-current = <50000>;
+};
+
+Example:
+
+bq24250 {
+	compatible = "ti,bq24250";
+	reg = <0x6a>;
+	interrupt-parent = <&gpio1>;
+	interrupts = <16 IRQ_TYPE_EDGE_BOTH>;
+
+	ti,battery-regulation-voltage = <4200000>;
+	ti,charge-current = <500000>;
+	ti,termination-current = <50000>;
+	ti,current-limit = <900000>;
+	ti,ovp-voltage = <9500000>;
+	ti,in-dpm-voltage = <4440000>;
+};
diff --git a/Documentation/devicetree/bindings/power/supply/bq25890.txt b/Documentation/devicetree/bindings/power/supply/bq25890.txt
new file mode 100644
index 000000000..c9dd17d14
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq25890.txt
@@ -0,0 +1,46 @@
+Binding for TI bq25890 Li-Ion Charger
+
+Required properties:
+- compatible: Should contain one of the following:
+    * "ti,bq25890"
+- reg: integer, i2c address of the device.
+- ti,battery-regulation-voltage: integer, maximum charging voltage (in uV);
+- ti,charge-current: integer, maximum charging current (in uA);
+- ti,termination-current: integer, charge will be terminated when current in
+    constant-voltage phase drops below this value (in uA);
+- ti,precharge-current: integer, maximum charge current during precharge
+    phase (in uA);
+- ti,minimum-sys-voltage: integer, when battery is charging and it is below
+    minimum system voltage, the system will be regulated above
+    minimum-sys-voltage setting (in uV);
+- ti,boost-voltage: integer, VBUS voltage level in boost mode (in uV);
+- ti,boost-max-current: integer, maximum allowed current draw in boost mode
+    (in uA).
+
+Optional properties:
+- ti,boost-low-freq: boolean, if present boost mode frequency will be 500kHz,
+    otherwise 1.5MHz;
+- ti,use-ilim-pin: boolean, if present the ILIM resistor will be used and the
+    input current will be the lower between the resistor setting and the IINLIM
+    register setting;
+- ti,thermal-regulation-threshold: integer, temperature above which the charge
+    current is lowered, to avoid overheating (in degrees Celsius). If omitted,
+    the default setting will be used (120 degrees);
+
+Example:
+
+bq25890 {
+        compatible = "ti,bq25890";
+        reg = <0x6a>;
+
+        ti,battery-regulation-voltage = <4200000>;
+        ti,charge-current = <1000000>;
+        ti,termination-current = <50000>;
+        ti,precharge-current = <128000>;
+        ti,minimum-sys-voltage = <3600000>;
+        ti,boost-voltage = <5000000>;
+        ti,boost-max-current = <1000000>;
+
+        ti,use-ilim-pin;
+        ti,thermal-regulation-threshold = <120>;
+};
diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt
new file mode 100644
index 000000000..37994fdb1
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt
@@ -0,0 +1,55 @@
+TI BQ27XXX fuel gauge family
+
+Required properties:
+- compatible: contains one of the following:
+ * "ti,bq27200" - BQ27200
+ * "ti,bq27210" - BQ27210
+ * "ti,bq27500" - deprecated, use revision specific property below
+ * "ti,bq27510" - deprecated, use revision specific property below
+ * "ti,bq27520" - deprecated, use revision specific property below
+ * "ti,bq27500-1" - BQ27500/1
+ * "ti,bq27510g1" - BQ27510-g1
+ * "ti,bq27510g2" - BQ27510-g2
+ * "ti,bq27510g3" - BQ27510-g3
+ * "ti,bq27520g1" - BQ27520-g1
+ * "ti,bq27520g2" - BQ27520-g2
+ * "ti,bq27520g3" - BQ27520-g3
+ * "ti,bq27520g4" - BQ27520-g4
+ * "ti,bq27521" - BQ27521
+ * "ti,bq27530" - BQ27530
+ * "ti,bq27531" - BQ27531
+ * "ti,bq27541" - BQ27541
+ * "ti,bq27542" - BQ27542
+ * "ti,bq27546" - BQ27546
+ * "ti,bq27742" - BQ27742
+ * "ti,bq27545" - BQ27545
+ * "ti,bq27421" - BQ27421
+ * "ti,bq27425" - BQ27425
+ * "ti,bq27426" - BQ27426
+ * "ti,bq27441" - BQ27441
+ * "ti,bq27621" - BQ27621
+- reg: integer, I2C address of the fuel gauge.
+
+Optional properties:
+- monitored-battery: phandle of battery characteristics node
+    The fuel gauge uses the following battery properties:
+    + energy-full-design-microwatt-hours
+    + charge-full-design-microamp-hours
+    + voltage-min-design-microvolt
+  Both or neither of the *-full-design-*-hours properties must be set.
+  See Documentation/devicetree/bindings/power/supply/battery.txt
+
+Example:
+
+	bat: battery {
+		compatible = "simple-battery";
+		voltage-min-design-microvolt = <3200000>;
+		energy-full-design-microwatt-hours = <5290000>;
+		charge-full-design-microamp-hours = <1430000>;
+	};
+
+	bq27510g3: fuel-gauge@55 {
+		compatible = "ti,bq27510g3";
+		reg = <0x55>;
+		monitored-battery = <&bat>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/charger-manager.txt b/Documentation/devicetree/bindings/power/supply/charger-manager.txt
new file mode 100644
index 000000000..ec4fe9de3
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/charger-manager.txt
@@ -0,0 +1,81 @@
+charger-manager bindings
+~~~~~~~~~~~~~~~~~~~~~~~~
+
+Required properties :
+ - compatible : "charger-manager"
+ - <>-supply : for regulator consumer
+ - cm-num-chargers : number of chargers
+ - cm-chargers : name of chargers
+ - cm-fuel-gauge : name of battery fuel gauge
+ - subnode <regulator> :
+	- cm-regulator-name : name of charger regulator
+	- subnode <cable> :
+		- cm-cable-name : name of charger cable
+		- cm-cable-extcon : name of extcon dev
+(optional)	- cm-cable-min : minimum current of cable
+(optional)	- cm-cable-max : maximum current of cable
+
+Optional properties :
+ - cm-name : charger manager's name (default : "battery")
+ - cm-poll-mode : polling mode (enum polling_modes)
+ - cm-poll-interval : polling interval
+ - cm-battery-stat : battery status (enum data_source)
+ - cm-fullbatt-* : data for full battery checking
+ - cm-thermal-zone : name of external thermometer's thermal zone
+ - cm-battery-* : threshold battery temperature for charging
+	-cold : critical cold temperature of battery for charging
+	-cold-in-minus : flag that cold temperature is in minus degrees
+	-hot : critical hot temperature of battery for charging
+	-temp-diff : temperature difference to allow recharging
+ - cm-dis/charging-max = limits of charging duration
+
+Example :
+	charger-manager@0 {
+		compatible = "charger-manager";
+		chg-reg-supply = <&charger_regulator>;
+
+		cm-name = "battery";
+		/* Always polling ON : 30s */
+		cm-poll-mode = <1>;
+		cm-poll-interval = <30000>;
+
+		cm-fullbatt-vchkdrop-ms = <30000>;
+		cm-fullbatt-vchkdrop-volt = <150000>;
+		cm-fullbatt-soc = <100>;
+
+		cm-battery-stat = <3>;
+
+		cm-num-chargers = <3>;
+		cm-chargers = "charger0", "charger1", "charger2";
+
+		cm-fuel-gauge = "fuelgauge0";
+
+		cm-thermal-zone = "thermal_zone.1"
+		/* in deci centigrade */
+		cm-battery-cold = <50>;
+		cm-battery-cold-in-minus;
+		cm-battery-hot = <800>;
+		cm-battery-temp-diff = <100>;
+
+		/* Allow charging for 5hr */
+		cm-charging-max = <18000000>;
+		/* Allow discharging for 2hr */
+		cm-discharging-max = <7200000>;
+
+		regulator@0 {
+			cm-regulator-name = "chg-reg";
+			cable@0 {
+				cm-cable-name = "USB";
+				cm-cable-extcon = "extcon-dev.0";
+				cm-cable-min = <475000>;
+				cm-cable-max = <500000>;
+			};
+			cable@1 {
+				cm-cable-name = "TA";
+				cm-cable-extcon = "extcon-dev.0";
+				cm-cable-min = <650000>;
+				cm-cable-max = <675000>;
+			};
+		};
+
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt
new file mode 100644
index 000000000..a04efa22d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/cpcap-battery.txt
@@ -0,0 +1,31 @@
+Motorola CPCAP PMIC battery driver binding
+
+Required properties:
+- compatible: Shall be "motorola,cpcap-battery"
+- interrupts: Interrupt specifier for each name in interrupt-names
+- interrupt-names: Should contain the following entries:
+		   "lowbph", "lowbpl", "chrgcurr1", "battdetb"
+- io-channels: IIO ADC channel specifier for each name in io-channel-names
+- io-channel-names: Should contain the following entries:
+		    "battdetb", "battp", "chg_isense", "batti"
+- power-supplies: List of phandles for power-supplying devices, as
+		  described in power_supply.txt. Typically a reference
+		  to cpcap_charger.
+
+Example:
+
+cpcap_battery: battery {
+	compatible = "motorola,cpcap-battery";
+	interrupts-extended = <
+		&cpcap 5 0 &cpcap 3 0
+		&cpcap 20 0 &cpcap 54 0
+	>;
+	interrupt-names =
+		"lowbph", "lowbpl",
+		"chrgcurr1", "battdetb";
+	io-channels = <&cpcap_adc 0 &cpcap_adc 1
+		       &cpcap_adc 5 &cpcap_adc 6>;
+	io-channel-names = "battdetb", "battp",
+			   "chg_isense", "batti";
+	power-supplies = <&cpcap_charger>;
+};
diff --git a/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt
new file mode 100644
index 000000000..80bd873c3
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/cpcap-charger.txt
@@ -0,0 +1,37 @@
+Motorola CPCAP PMIC battery charger binding
+
+Required properties:
+- compatible: Shall be "motorola,mapphone-cpcap-charger"
+- interrupts: Interrupt specifier for each name in interrupt-names
+- interrupt-names: Should contain the following entries:
+		   "chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn",
+		   "rvrs_mode", "chrgcurr1", "vbusvld", "battdetb"
+- io-channels: IIO ADC channel specifier for each name in io-channel-names
+- io-channel-names: Should contain the following entries:
+		    "battdetb", "battp", "vbus", "chg_isense", "batti"
+
+Optional properties:
+- mode-gpios: Optionally CPCAP charger can have a companion wireless
+	      charge controller that is controlled with two GPIOs
+	      that are active low.
+
+Example:
+
+cpcap_charger: charger {
+	compatible = "motorola,mapphone-cpcap-charger";
+	interrupts-extended = <
+		&cpcap 13 0 &cpcap 12 0 &cpcap 29 0 &cpcap 28 0
+		&cpcap 22 0 &cpcap 20 0 &cpcap 19 0 &cpcap 54 0
+	>;
+	interrupt-names =
+		"chrg_det", "rvrs_chrg", "chrg_se1b", "se0conn",
+		"rvrs_mode", "chrgcurr1", "vbusvld", "battdetb";
+	mode-gpios = <&gpio3 29 GPIO_ACTIVE_LOW
+		      &gpio3 23 GPIO_ACTIVE_LOW>;
+	io-channels = <&cpcap_adc 0 &cpcap_adc 1
+		       &cpcap_adc 2 &cpcap_adc 5
+		       &cpcap_adc 6>;
+	io-channel-names = "battdetb", "battp",
+			   "vbus", "chg_isense",
+			   "batti";
+};
diff --git a/Documentation/devicetree/bindings/power/supply/da9150-charger.txt b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt
new file mode 100644
index 000000000..f3906663c
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/da9150-charger.txt
@@ -0,0 +1,26 @@
+Dialog Semiconductor DA9150 Charger Power Supply bindings
+
+Required properties:
+- compatible: "dlg,da9150-charger" for DA9150 Charger Power Supply
+
+Optional properties:
+- io-channels: List of phandle and IIO specifier pairs
+- io-channel-names: List of channel names used by charger
+      ["CHAN_IBUS", "CHAN_VBUS", "CHAN_TJUNC", "CHAN_VBAT"]
+  (See Documentation/devicetree/bindings/iio/iio-bindings.txt for further info)
+
+
+Example:
+
+	da9150-charger {
+		compatible = "dlg,da9150-charger";
+
+		io-channels = <&gpadc 0>,
+			      <&gpadc 2>,
+			      <&gpadc 8>,
+			      <&gpadc 5>;
+		io-channel-names = "CHAN_IBUS",
+				   "CHAN_VBUS",
+				   "CHAN_TJUNC",
+				   "CHAN_VBAT";
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/da9150-fg.txt b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt
new file mode 100644
index 000000000..00236fe3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/da9150-fg.txt
@@ -0,0 +1,23 @@
+Dialog Semiconductor DA9150 Fuel-Gauge Power Supply bindings
+
+Required properties:
+- compatible: "dlg,da9150-fuel-gauge" for DA9150 Fuel-Gauge Power Supply
+
+Optional properties:
+- dlg,update-interval: Interval time (milliseconds) between battery level checks.
+- dlg,warn-soc-level: Battery discharge level (%) where warning event raised.
+      [1 - 100]
+- dlg,crit-soc-level: Battery discharge level (%) where critical event raised.
+  This value should be lower than the warning level.
+      [1 - 100]
+
+
+Example:
+
+	fuel-gauge {
+		compatible = "dlg,da9150-fuel-gauge";
+
+		dlg,update-interval = <10000>;
+		dlg,warn-soc-level = /bits/ 8 <15>;
+		dlg,crit-soc-level = /bits/ 8 <5>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/gpio-charger.txt b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt
new file mode 100644
index 000000000..adbb5dc5b
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/gpio-charger.txt
@@ -0,0 +1,27 @@
+gpio-charger
+
+Required properties :
+ - compatible : "gpio-charger"
+ - gpios : GPIO indicating the charger presence.
+   See GPIO binding in bindings/gpio/gpio.txt .
+ - charger-type : power supply type, one of
+     unknown
+     battery
+     ups
+     mains
+     usb-sdp (USB standard downstream port)
+     usb-dcp (USB dedicated charging port)
+     usb-cdp (USB charging downstream port)
+     usb-aca (USB accessory charger adapter)
+
+Example:
+
+	usb_charger: charger {
+		compatible = "gpio-charger";
+		charger-type = "usb-sdp";
+		gpios = <&gpf0 2 0 0 0>;
+	}
+
+	battery {
+		power-supplies = <&usb_charger>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/isp1704.txt b/Documentation/devicetree/bindings/power/supply/isp1704.txt
new file mode 100644
index 000000000..fa3596907
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/isp1704.txt
@@ -0,0 +1,17 @@
+Binding for NXP ISP1704 USB Charger Detection
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "nxp,isp1704"
+- nxp,enable-gpio: Should contain a phandle + gpio-specifier
+  to the GPIO pin connected to the chip's enable pin.
+- usb-phy: Should contain a phandle to the USB PHY
+  the ISP1704 is connected to.
+
+Example:
+
+isp1704 {
+	compatible = "nxp,isp1704";
+	nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_LOW>;
+	usb-phy = <&usb2_phy>;
+};
diff --git a/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt
new file mode 100644
index 000000000..5485633b1
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/lego_ev3_battery.txt
@@ -0,0 +1,21 @@
+LEGO MINDSTORMS EV3 Battery
+~~~~~~~~~~~~~~~~~~~~~~~~~~~
+
+LEGO MINDSTORMS EV3 has some built-in capability for monitoring the battery.
+It uses 6 AA batteries or a special Li-ion rechargeable battery pack that is
+detected by a key switch in the battery compartment.
+
+Required properties:
+ - compatible: Must be "lego,ev3-battery"
+ - io-channels: phandles to analog inputs for reading voltage and current
+ - io-channel-names: Must be "voltage", "current"
+ - rechargeable-gpios: phandle to the rechargeable battery indication gpio
+
+Example:
+
+	battery {
+		compatible = "lego,ev3-battery";
+		io-channels = <&adc 4>, <&adc 3>;
+		io-channel-names = "voltage", "current";
+		rechargeable-gpios = <&gpio 136 GPIO_ACTIVE_LOW>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt
new file mode 100644
index 000000000..0355a4b68
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/lp8727_charger.txt
@@ -0,0 +1,43 @@
+Binding for TI/National Semiconductor LP8727 Charger
+
+Required properties:
+- compatible: "ti,lp8727"
+- reg: I2C slave address 27h
+
+Optional properties:
+- interrupts: interrupt specifier (see interrupt binding[0])
+- debounce-ms: interrupt debounce time. (u32)
+
+AC and USB charging parameters
+- charger-type: "ac" or "usb" (string)
+- eoc-level: value of 'enum lp8727_eoc_level' (u8)
+- charging-current: value of 'enum lp8727_ichg' (u8)
+
+[0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+
+Example)
+
+lp8727@27 {
+	compatible = "ti,lp8727";
+	reg = <0x27>;
+
+	/* GPIO 134 is used for LP8728 interrupt pin */
+	interrupt-parent = <&gpio5>; 	/* base = 128 */
+	interrupts = <6 0x2>;		/* offset = 6, falling edge type */
+
+	debounce-ms = <300>;
+
+	/* AC charger: 5% EOC and 500mA charging current */
+	ac {
+		charger-type = "ac";
+		eoc-level = /bits/ 8 <0>;
+		charging-current = /bits/ 8 <4>;
+	};
+
+	/* USB charger: 10% EOC and 400mA charging current */
+	usb {
+		charger-type = "usb";
+		eoc-level = /bits/ 8 <1>;
+		charging-current = /bits/ 8 <2>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/power/supply/ltc2941.txt b/Documentation/devicetree/bindings/power/supply/ltc2941.txt
new file mode 100644
index 000000000..3b9ba147b
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/ltc2941.txt
@@ -0,0 +1,28 @@
+binding for LTC2941, LTC2942, LTC2943 and LTC2944 battery gauges
+
+All chips measure battery capacity.
+The LTC2942 is pin compatible with the LTC2941, it adds voltage and
+temperature monitoring, and is runtime detected. LTC2943 and LTC2944
+is software compatible, uses a slightly different conversion formula
+for the charge counter and adds voltage, current and temperature monitoring.
+
+Required properties:
+- compatible: Should contain "lltc,ltc2941", "lltc,ltc2942", "lltc,ltc2943"
+    or "lltc,ltc2944" which also indicates the type of I2C chip attached.
+- reg: The 7-bit I2C address.
+- lltc,resistor-sense: The sense resistor value in milli-ohms. Can be a 32-bit
+    negative value when the battery has been connected to the wrong end of the
+    resistor.
+- lltc,prescaler-exponent: The prescaler exponent as explained in the datasheet.
+    This determines the range and accuracy of the gauge. The value is programmed
+    into the chip only if it differs from the current setting. The setting is
+    lost when the battery is disconnected.
+
+Example from the Topic Miami Florida board:
+
+	fuelgauge: ltc2943@64 {
+		compatible = "lltc,ltc2943";
+		reg = <0x64>;
+		lltc,resistor-sense = <15>;
+		lltc,prescaler-exponent = <5>; /* 2^(2*5) = 1024 */
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt
new file mode 100644
index 000000000..71f2840e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/ltc3651-charger.txt
@@ -0,0 +1,27 @@
+ltc3651-charger
+
+Required properties:
+ - compatible: "lltc,ltc3651-charger"
+ - lltc,acpr-gpios: Connect to ACPR output. See remark below.
+
+Optional properties:
+ - lltc,fault-gpios: Connect to FAULT output. See remark below.
+ - lltc,chrg-gpios: Connect to CHRG output. See remark below.
+
+The ltc3651 outputs are open-drain type and active low. The driver assumes the
+GPIO reports "active" when the output is asserted, so if the pins have been
+connected directly, the GPIO flags should be set to active low also.
+
+The driver will attempt to aquire interrupts for all GPIOs to detect changes in
+line state. If the system is not capabale of providing interrupts, the driver
+cannot report changes and userspace will need to periodically read the sysfs
+attributes to detect changes.
+
+Example:
+
+	charger: battery-charger {
+		compatible = "lltc,ltc3651-charger";
+		lltc,acpr-gpios = <&gpio0 68 GPIO_ACTIVE_LOW>;
+		lltc,fault-gpios = <&gpio0 64 GPIO_ACTIVE_LOW>;
+		lltc,chrg-gpios = <&gpio0 63 GPIO_ACTIVE_LOW>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/max17042_battery.txt b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt
new file mode 100644
index 000000000..3f3894aae
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/max17042_battery.txt
@@ -0,0 +1,31 @@
+max17042_battery
+~~~~~~~~~~~~~~~~
+
+Required properties :
+ - compatible : "maxim,max17042"
+
+Optional properties :
+ - maxim,rsns-microohm : Resistance of rsns resistor in micro Ohms
+                         (datasheet-recommended value is 10000).
+   Defining this property enables current-sense functionality.
+
+Optional threshold properties :
+ If skipped the condition won't be reported.
+ - maxim,cold-temp :      Temperature threshold to report battery
+                          as cold (in tenths of degree Celsius).
+ - maxim,over-heat-temp : Temperature threshold to report battery
+                          as over heated (in tenths of degree Celsius).
+ - maxim,dead-volt :      Voltage threshold to report battery
+                          as dead (in mV).
+ - maxim,over-volt :      Voltage threshold to report battery
+                          as over voltage (in mV).
+
+Example:
+
+	battery-charger@36 {
+		compatible = "maxim,max17042";
+		reg = <0x36>;
+		maxim,rsns-microohm = <10000>;
+		maxim,over-heat-temp = <600>;
+		maxim,over-volt = <4300>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/max8903-charger.txt b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt
new file mode 100644
index 000000000..bab947fef
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/max8903-charger.txt
@@ -0,0 +1,24 @@
+Maxim Semiconductor MAX8903 Battery Charger bindings
+
+Required properties:
+- compatible: "maxim,max8903" for MAX8903 Battery Charger
+- dok-gpios: Valid DC power has been detected (active low, input), optional if uok-gpios is provided
+- uok-gpios: Valid USB power has been detected (active low, input), optional if dok-gpios is provided
+
+Optional properties:
+- cen-gpios: Charge enable pin (active low, output)
+- chg-gpios: Charger status pin (active low, input)
+- flt-gpios: Fault pin (active low, output)
+- dcm-gpios: Current limit mode setting (DC=1 or USB=0, output)
+- usus-gpios: USB suspend pin (active high, output)
+
+
+Example:
+
+	max8903-charger {
+		compatible = "maxim,max8903";
+		dok-gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		flt-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
+		chg-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>;
+		cen-gpios = <&gpio2 5 GPIO_ACTIVE_LOW>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/max8925_battery.txt b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt
new file mode 100644
index 000000000..d7e3e0c0f
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/max8925_battery.txt
@@ -0,0 +1,18 @@
+max8925-battery bindings
+~~~~~~~~~~~~~~~~
+
+Optional properties :
+ - batt-detect: whether support battery detect
+ - topoff-threshold: set charging current in topoff mode
+ - fast-charge: set charging current in fast mode
+ - no-temp-support: whether support temperature protection detect
+ - no-insert-detect: whether support insert detect
+
+Example:
+	charger {
+		batt-detect = <0>;
+		topoff-threshold = <1>;
+		fast-charge = <7>;
+		no-temp-support = <0>;
+		no-insert-detect = <0>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt
new file mode 100644
index 000000000..55967a0be
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/maxim,ds2760.txt
@@ -0,0 +1,26 @@
+Devicetree bindings for Maxim DS2760
+====================================
+
+The ds2760 is a w1 slave device and must hence have its sub-node in DT
+under a w1 bus master node.
+
+The device exposes a power supply, so the details described in
+Documentation/devicetree/bindings/power/supply/power_supply.txt apply.
+
+Required properties:
+- compatible: must be "maxim,ds2760"
+
+Optional properties:
+- power-supplies:	Refers to one or more power supplies connected to
+			this battery.
+- maxim,pmod-enabled:	This boolean property enables the DS2760 to enter
+			sleep mode when the DQ line goes low for greater
+			than 2 seconds and leave sleep Mode when the DQ
+			line goes high.
+- maxim,cache-time-ms:	Time im milliseconds to cache the data for. When
+			this time expires, the values are read again from
+			the hardware. Defaults to 1000.
+- rated-capacity-microamp-hours:
+			The rated capacity of the battery, in mAh.
+			If not specified, the value stored in the
+			non-volatile chip memory is used.
diff --git a/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt
new file mode 100644
index 000000000..f956247d4
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/maxim,max14656.txt
@@ -0,0 +1,23 @@
+Maxim MAX14656 / AL32 USB Charger Detector
+
+Required properties :
+- compatible : "maxim,max14656";
+- reg: i2c slave address
+- interrupts: interrupt line
+
+Example:
+
+&i2c2 {
+	clock-frequency = <50000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+
+	max14656@35 {
+		compatible = "maxim,max14656";
+		reg = <0x35>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_charger_detect>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <26 IRQ_TYPE_LEVEL_HIGH>;
+	};
+};
diff --git a/Documentation/devicetree/bindings/power/supply/olpc_battery.txt b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt
new file mode 100644
index 000000000..c8901b399
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/olpc_battery.txt
@@ -0,0 +1,5 @@
+OLPC battery
+~~~~~~~~~~~~
+
+Required properties:
+  - compatible : "olpc,xo1-battery"
diff --git a/Documentation/devicetree/bindings/power/supply/power_supply.txt b/Documentation/devicetree/bindings/power/supply/power_supply.txt
new file mode 100644
index 000000000..8391bfa0e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/power_supply.txt
@@ -0,0 +1,23 @@
+Power Supply Core Support
+
+Optional Properties:
+ - power-supplies : This property is added to a supply in order to list the
+   devices which supply it power, referenced by their phandles.
+
+Example:
+
+	usb-charger: power@e {
+		compatible = "some,usb-charger";
+		...
+	};
+
+	ac-charger: power@c {
+		compatible = "some,ac-charger";
+		...
+	};
+
+	battery@b {
+		compatible = "some,battery";
+		...
+		power-supplies = <&usb-charger>, <&ac-charger>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt
new file mode 100644
index 000000000..747899223
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/qcom,coincell-charger.txt
@@ -0,0 +1,48 @@
+Qualcomm Coincell Charger:
+
+The hardware block controls charging for a coincell or capacitor that is
+used to provide power backup for certain features of the power management
+IC (PMIC)
+
+- compatible:
+	Usage: required
+	Value type: <string>
+	Definition: must be: "qcom,pm8941-coincell"
+
+- reg:
+	Usage: required
+	Value type: <u32>
+	Definition: base address of the coincell charger registers
+
+- qcom,rset-ohms:
+	Usage: required
+	Value type: <u32>
+	Definition: resistance (in ohms) for current-limiting resistor
+		must be one of: 800, 1200, 1700, 2100
+
+- qcom,vset-millivolts:
+	Usage: required
+	Value type: <u32>
+	Definition: voltage (in millivolts) to apply for charging
+		must be one of: 2500, 3000, 3100, 3200
+
+- qcom,charger-disable:
+	Usage: optional
+	Value type: <boolean>
+	Definition: defining this property disables charging
+
+This charger is a sub-node of one of the 8941 PMIC blocks, and is specified
+as a child node in DTS of that node.  See ../mfd/qcom,spmi-pmic.txt and
+../mfd/qcom-pm8xxx.txt
+
+Example:
+
+	pm8941@0 {
+		coincell@2800 {
+			compatible = "qcom,pm8941-coincell";
+			reg = <0x2800>;
+
+			qcom,rset-ohms = <2100>;
+			qcom,vset-millivolts = <3000>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt
new file mode 100644
index 000000000..06f8a5ddb
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/qcom_smbb.txt
@@ -0,0 +1,150 @@
+Qualcomm Switch-Mode Battery Charger and Boost
+
+PROPERTIES
+- compatible:
+  Usage: required
+  Value type: <stringlist>
+  Description: Must be one of:
+               - "qcom,pm8941-charger"
+
+- reg:
+  Usage: required
+  Value type: <prop-encoded-array>
+  Description: Base address of registers for SMBB block
+
+- interrupts:
+  Usage: required
+  Value type: <prop-encoded-array>
+  Description: The format of the specifier is defined by the binding document
+               describing the node's interrupt parent.  Must contain one
+               specifier for each of the following interrupts, in order:
+               - charge done
+               - charge fast mode
+               - charge trickle mode
+               - battery temperature ok
+               - battery present
+               - charger disconnected
+               - USB-in valid
+               - DC-in valid
+
+- interrupt-names:
+  Usage: required
+  Value type: <stringlist>
+  Description: Must contain the following list, strictly ordered:
+               "chg-done",
+               "chg-fast",
+               "chg-trkl",
+               "bat-temp-ok",
+               "bat-present",
+               "chg-gone",
+               "usb-valid",
+               "dc-valid"
+
+- qcom,fast-charge-current-limit:
+  Usage: optional (default: 1A, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 3A]
+  Description: Maximum charge current; May be clamped to safety limits.
+
+- qcom,fast-charge-low-threshold-voltage:
+  Usage: optional (default: 3.2V, or pre-configured value)
+  Value type: <u32>; uV; range [2.1V : 3.6V]
+  Description: Battery voltage limit above which fast charging may operate;
+               Below this value linear or switch-mode auto-trickle-charging
+               will operate.
+
+- qcom,fast-charge-high-threshold-voltage:
+  Usage: optional (default: 4.2V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Battery voltage limit below which fast charging may operate;
+               The fast charger will attempt to charge the battery to this
+               voltage.  May be clamped to safety limits.
+
+- qcom,fast-charge-safe-voltage:
+  Usage: optional (default: 4.2V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Maximum safe battery voltage; May be pre-set by bootloader, in
+               which case, setting this will harmlessly fail. The property
+               'fast-charge-high-watermark' will be clamped by this value.
+
+- qcom,fast-charge-safe-current:
+  Usage: optional (default: 1A, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 3A]
+  Description: Maximum safe battery charge current; May pre-set by bootloader,
+               in which case, setting this will harmlessly fail. The property
+               'qcom,fast-charge-current-limit' will be clamped by this value.
+
+- qcom,auto-recharge-threshold-voltage:
+  Usage: optional (default: 4.1V, or pre-configured value)
+  Value type: <u32>; uV; range [3.24V : 5V]
+  Description: Battery voltage limit below which auto-recharge functionality
+               will restart charging after end-of-charge;  The high cutoff
+               limit for auto-recharge is 5% above this value.
+
+- qcom,minimum-input-voltage:
+  Usage: optional (default: 4.3V, or pre-configured value)
+  Value type: <u32>; uV; range [4.2V : 9.6V]
+  Description: Input voltage level above which charging may operate
+
+- qcom,dc-current-limit:
+  Usage: optional (default: 100mA, or pre-configured value)
+  Value type: <u32>; uA; range [100mA : 2.5A]
+  Description: Default DC charge current limit
+
+- qcom,disable-dc:
+  Usage: optional (default: false)
+  Value type: boolean: <u32> or <empty>
+  Description: Disable DC charger
+
+- qcom,jeita-extended-temp-range:
+  Usage: optional (default: false)
+  Value type: boolean: <u32> or <empty>
+  Description: Enable JEITA extended temperature range;  This does *not*
+               adjust the maximum charge voltage or current in the extended
+               temperature range.  It only allows charging when the battery
+               is in the extended temperature range.  Voltage/current
+               regulation must be done externally to fully comply with
+               the JEITA safety guidelines if this flag is set.
+
+- usb_otg_in-supply:
+  Usage: optional
+  Value type: <phandle>
+  Description: Reference to the regulator supplying power to the USB_OTG_IN
+               pin.
+
+child nodes:
+- otg-vbus:
+  Usage: optional
+  Description: This node defines a regulator used to control the direction
+               of VBUS voltage - specifically: whether to supply voltage
+               to VBUS for host mode operation of the OTG port, or allow
+               input voltage from external VBUS for charging.  In the
+               hardware, the supply for this regulator comes from
+               usb_otg_in-supply.
+
+EXAMPLE
+charger@1000 {
+       compatible = "qcom,pm8941-charger";
+       reg = <0x1000 0x700>;
+       interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
+                       <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
+       interrupt-names = "chg-done",
+                       "chg-fast",
+                       "chg-trkl",
+                       "bat-temp-ok",
+                       "bat-present",
+                       "chg-gone",
+                       "usb-valid",
+                       "dc-valid";
+
+       qcom,fast-charge-current-limit = <1000000>;
+       qcom,dc-charge-current-limit = <1000000>;
+       usb_otg_in-supply = <&pm8941_5vs1>;
+
+       otg-vbus {};
+};
diff --git a/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt
new file mode 100644
index 000000000..1e6107c75
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/rt9455_charger.txt
@@ -0,0 +1,46 @@
+Binding for Richtek rt9455 battery charger
+
+Required properties:
+- compatible:				it should contain one of the following:
+					"richtek,rt9455".
+- reg:					integer, i2c address of the device.
+- interrupts:				interrupt mapping for GPIO IRQ, it should be
+					configured with IRQ_TYPE_LEVEL_LOW flag.
+- richtek,output-charge-current:	integer, output current from the charger to the
+					battery, in uA.
+- richtek,end-of-charge-percentage:	integer, percent of the output charge current.
+					When the current in constant-voltage phase drops
+					below output_charge_current x end-of-charge-percentage,
+					charge is terminated.
+- richtek,battery-regulation-voltage:	integer, maximum battery voltage in uV.
+- richtek,boost-output-voltage:		integer, maximum voltage provided to consumer
+					devices, when the charger is in boost mode, in uV.
+
+Optional properties:
+- richtek,min-input-voltage-regulation: integer, input voltage level in uV, used to
+					decrease voltage level when the over current
+					of the input power source occurs.
+					This prevents input voltage drop due to insufficient
+					current provided by the power source.
+					Default: 4500000 uV (4.5V)
+- richtek,avg-input-current-regulation: integer, input current value in uA drained by the
+					charger from the power source.
+					Default: 500000 uA (500mA)
+
+Example:
+
+rt9455@22 {
+	compatible = "richtek,rt9455";
+	reg = <0x22>;
+
+	interrupt-parent = <&gpio1>;
+	interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+
+	richtek,output-charge-current	    = <500000>;
+	richtek,end-of-charge-percentage    = <10>;
+	richtek,battery-regulation-voltage  = <4200000>;
+	richtek,boost-output-voltage	    = <5050000>;
+
+	richtek,min-input-voltage-regulation = <4500000>;
+	richtek,avg-input-current-regulation = <500000>;
+};
diff --git a/Documentation/devicetree/bindings/power/supply/rx51-battery.txt b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt
new file mode 100644
index 000000000..90438453d
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/rx51-battery.txt
@@ -0,0 +1,25 @@
+Binding for Nokia N900 battery
+
+The Nokia N900 battery status can be read via the TWL4030's A/D converter.
+
+Required properties:
+- compatible: Should contain one of the following:
+ * "nokia,n900-battery"
+- io-channels: Should contain IIO channel specifiers
+               for each element in io-channel-names.
+- io-channel-names: Should contain the following values:
+ * "temp" - The ADC channel for temperature reading
+ * "bsi"  - The ADC channel for battery size identification
+ * "vbat" - The ADC channel to measure the battery voltage
+
+Example from Nokia N900:
+
+battery: n900-battery {
+	compatible = "nokia,n900-battery";
+	io-channels = <&twl4030_madc 0>,
+		      <&twl4030_madc 4>,
+		      <&twl4030_madc 12>;
+	io-channel-names = "temp",
+			   "bsi",
+			   "vbat";
+};
diff --git a/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt
new file mode 100644
index 000000000..4b2195571
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/sbs,sbs-manager.txt
@@ -0,0 +1,66 @@
+Binding for sbs-manager
+
+Required properties:
+- compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part
+  number compatible string might be used in order to take care of vendor
+  specific registers.
+- reg: integer, i2c address of the device. Should be <0xa>.
+Optional properties:
+- gpio-controller: Marks the port as GPIO controller.
+  See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
+- #gpio-cells: Should be <2>. The first cell is the pin number, the second cell
+  is used to specify optional parameters:
+  See "gpio-specifier" in .../devicetree/bindings/gpio/gpio.txt.
+
+From OS view the device is basically an i2c-mux used to communicate with up to
+four smart battery devices at address 0xb. The driver actually implements this
+behaviour. So standard i2c-mux nodes can be used to register up to four slave
+batteries. Channels will be numerated starting from 1 to 4.
+
+Example:
+
+batman@a {
+    compatible = "lltc,ltc1760", "sbs,sbs-manager";
+    reg = <0x0a>;
+    #address-cells = <1>;
+    #size-cells = <0>;
+
+    gpio-controller;
+    #gpio-cells = <2>;
+
+    i2c@1 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <1>;
+
+        battery@b {
+            compatible = "ti,bq2060", "sbs,sbs-battery";
+            reg = <0x0b>;
+            sbs,battery-detect-gpios = <&batman 1 1>;
+        };
+    };
+
+    i2c@2 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <2>;
+
+        battery@b {
+            compatible = "ti,bq2060", "sbs,sbs-battery";
+            reg = <0x0b>;
+            sbs,battery-detect-gpios = <&batman 2 1>;
+        };
+    };
+
+    i2c@3 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        reg = <3>;
+
+        battery@b {
+            compatible = "ti,bq2060", "sbs,sbs-battery";
+            reg = <0x0b>;
+            sbs,battery-detect-gpios = <&batman 3 1>;
+        };
+    };
+};
diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt
new file mode 100644
index 000000000..4e78e5101
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-battery.txt
@@ -0,0 +1,27 @@
+SBS sbs-battery
+~~~~~~~~~~
+
+Required properties :
+ - compatible: "<vendor>,<part-number>", "sbs,sbs-battery" as fallback. The
+     part number compatible string might be used in order to take care of
+     vendor specific registers.
+     Known <vendor>,<part-number>:
+       ti,bq20z75
+
+Optional properties :
+ - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c
+   IO failure.
+ - sbs,poll-retry-count : The number of times to try looking for new status
+   after an external change notification.
+ - sbs,battery-detect-gpios : The gpio which signals battery detection and
+   a flag specifying its polarity.
+
+Example:
+
+	battery@b {
+		compatible = "ti,bq20z75", "sbs,sbs-battery";
+		reg = <0xb>;
+		sbs,i2c-retry-count = <2>;
+		sbs,poll-retry-count = <10>;
+		sbs,battery-detect-gpios = <&gpio-controller 122 1>;
+	}
diff --git a/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt
new file mode 100644
index 000000000..84e74151e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/sbs_sbs-charger.txt
@@ -0,0 +1,21 @@
+SBS sbs-charger
+~~~~~~~~~~
+
+Required properties:
+ - compatible: "<vendor>,<part-number>", "sbs,sbs-charger" as fallback. The part
+     number compatible string might be used in order to take care of vendor
+     specific registers.
+
+Optional properties:
+- interrupts: Interrupt mapping for GPIO IRQ. Use in conjunction with
+    "interrupt-parent". If an interrupt is not provided the driver will switch
+    automatically to polling.
+
+Example:
+
+	ltc4100@9 {
+		compatible = "lltc,ltc4100", "sbs,sbs-charger";
+		reg = <0x9>;
+		interrupt-parent = <&gpio6>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt
new file mode 100644
index 000000000..de45e1a2a
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/ti,bq24735.txt
@@ -0,0 +1,39 @@
+TI BQ24735 Charge Controller
+~~~~~~~~~~
+
+Required properties :
+ - compatible : "ti,bq24735"
+
+Optional properties :
+ - interrupts : Specify the interrupt to be used to trigger when the AC
+   adapter is either plugged in or removed.
+ - ti,ac-detect-gpios : This GPIO is optionally used to read the AC adapter
+   status. This is a Host GPIO that is configured as an input and connected
+   to the ACOK pin on the bq24735. Note: for backwards compatibility reasons,
+   the GPIO must be active on AC adapter absence despite ACOK being active
+   (high) on AC adapter presence.
+ - ti,charge-current : Used to control and set the charging current. This value
+   must be between 128mA and 8.128A with a 64mA step resolution. The POR value
+   is 0x0000h. This number is in mA (e.g. 8192), see spec for more information
+   about the ChargeCurrent (0x14h) register.
+ - ti,charge-voltage : Used to control and set the charging voltage. This value
+   must be between 1.024V and 19.2V with a 16mV step resolution. The POR value
+   is 0x0000h. This number is in mV (e.g. 19200), see spec for more information
+   about the ChargeVoltage (0x15h) register.
+ - ti,input-current : Used to control and set the charger input current. This
+   value must be between 128mA and 8.064A with a 128mA step resolution. The
+   POR value is 0x1000h. This number is in mA (e.g. 8064), see the spec for
+   more information about the InputCurrent (0x3fh) register.
+ - ti,external-control : Indicates that the charger is configured externally
+   and that the host should not attempt to enable/disable charging or set the
+   charge voltage/current.
+ - poll-interval : In case 'interrupts' is not specified, poll AC adapter
+   presence with this interval (milliseconds).
+
+Example:
+
+	bq24735@9 {
+		compatible = "ti,bq24735";
+		reg = <0x9>;
+		ti,ac-detect-gpios = <&gpio 72 0x1>;
+	}
diff --git a/Documentation/devicetree/bindings/power/supply/tps65090.txt b/Documentation/devicetree/bindings/power/supply/tps65090.txt
new file mode 100644
index 000000000..8e5e0d391
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/tps65090.txt
@@ -0,0 +1,17 @@
+TPS65090 Frontend PMU with Switchmode Charger
+
+Required Properties:
+-compatible: "ti,tps65090-charger"
+
+Optional Properties:
+-ti,enable-low-current-chrg: Enables charging when a low current is detected
+ while the default logic is to stop charging.
+
+This node is a subnode of the tps65090 PMIC.
+
+Example:
+
+	tps65090-charger {
+		compatible = "ti,tps65090-charger";
+		ti,enable-low-current-chrg;
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt
new file mode 100644
index 000000000..a11072c5a
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/tps65217_charger.txt
@@ -0,0 +1,17 @@
+TPS65217 Charger
+
+Required Properties:
+-compatible: "ti,tps65217-charger"
+-interrupts: TPS65217 interrupt numbers for the AC and USB charger input change.
+             Should be <0> for the USB charger and <1> for the AC adapter.
+-interrupt-names: Should be "USB" and "AC"
+
+This node is a subnode of the tps65217 PMIC.
+
+Example:
+
+	tps65217-charger {
+		compatible = "ti,tps65217-charger";
+		interrupts = <0>, <1>;
+		interrupt-names = "USB", "AC";
+	};
diff --git a/Documentation/devicetree/bindings/power/supply/twl-charger.txt b/Documentation/devicetree/bindings/power/supply/twl-charger.txt
new file mode 100644
index 000000000..3b4ea1b73
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/twl-charger.txt
@@ -0,0 +1,30 @@
+TWL BCI (Battery Charger Interface)
+
+The battery charger needs to interact with the USB phy in order
+to know when charging is permissible, and when there is a connection
+or disconnection.
+
+The choice of phy cannot be configured at a hardware level, so there
+is no value in explicit configuration in device-tree.  Rather
+if there is a sibling of the BCI node which is compatible with
+"ti,twl4030-usb", then that is used to determine when and how
+use USB power for charging.
+
+Required properties:
+- compatible:
+  - "ti,twl4030-bci"
+- interrupts: two interrupt lines from the TWL SIH (secondary
+  interrupt handler) - interrupts 9 and 2.
+
+Optional properties:
+- ti,bb-uvolt: microvolts for charging the backup battery.
+- ti,bb-uamp: microamps for charging the backup battery.
+
+Examples:
+
+bci {
+   compatible = "ti,twl4030-bci";
+   interrupts = <9>, <2>;
+   ti,bb-uvolt = <3200000>;
+   ti,bb-uamp = <150>;
+};