Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 92 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/regulator/pwm-regulator.txt b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
new file mode 100644
index 000000000..3d78d507e
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/pwm-regulator.txt
@@ -0,0 +1,92 @@
+Bindings for the Generic PWM Regulator
+======================================
+
+Currently supports 2 modes of operation:
+
+Voltage Table:		When in this mode, a voltage table (See below) of
+			predefined voltage <=> duty-cycle values must be
+			provided via DT. Limitations are that the regulator can
+			only operate at the voltages supplied in the table.
+			Intermediary duty-cycle values which would normally
+			allow finer grained voltage selection are ignored and
+			rendered useless.  Although more control is given to
+			the user if the assumptions made in continuous-voltage
+			mode do not reign true.
+
+Continuous Voltage:	This mode uses the regulator's maximum and minimum
+			supplied voltages specified in the
+			regulator-{min,max}-microvolt properties to calculate
+			appropriate duty-cycle values.  This allows for a much
+			more fine grained solution when compared with
+			voltage-table mode above.  This solution does make an
+			assumption that a %50 duty-cycle value will cause the
+			regulator voltage to run at half way between the
+			supplied max_uV and min_uV values.
+
+Required properties:
+--------------------
+- compatible:		Should be "pwm-regulator"
+
+- pwms:			PWM specification (See: ../pwm/pwm.txt)
+
+Only required for Voltage Table Mode:
+- voltage-table: 	Voltage and Duty-Cycle table consisting of 2 cells
+			    First cell is voltage in microvolts (uV)
+			    Second cell is duty-cycle in percent (%)
+
+Optional properties for Continuous mode:
+- pwm-dutycycle-unit:	Integer value encoding the duty cycle unit. If not
+			defined, <100> is assumed, meaning that
+			pwm-dutycycle-range contains values expressed in
+			percent.
+
+- pwm-dutycycle-range:	Should contain 2 entries. The first entry is encoding
+			the dutycycle for regulator-min-microvolt and the
+			second one the dutycycle for regulator-max-microvolt.
+			Duty cycle values are expressed in pwm-dutycycle-unit.
+			If not defined, <0 100> is assumed.
+
+NB: To be clear, if voltage-table is provided, then the device will be used
+in Voltage Table Mode.  If no voltage-table is provided, then the device will
+be used in Continuous Voltage Mode.
+
+Optional properties:
+--------------------
+- enable-gpios:		GPIO to use to enable/disable the regulator
+
+Any property defined as part of the core regulator binding can also be used.
+(See: ../regulator/regulator.txt)
+
+Continuous Voltage With Enable GPIO Example:
+	pwm_regulator {
+		compatible = "pwm-regulator";
+		pwms = <&pwm1 0 8448 0>;
+		enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <1016000>;
+		regulator-max-microvolt = <1114000>;
+		regulator-name = "vdd_logic";
+		/* unit == per-mille */
+		pwm-dutycycle-unit = <1000>;
+		/*
+		 * Inverted PWM logic, and the duty cycle range is limited
+		 * to 30%-70%.
+		 */
+		pwm-dutycycle-range = <700 300>; /* */
+	};
+
+Voltage Table Example:
+	pwm_regulator {
+		compatible = "pwm-regulator";
+		pwms = <&pwm1 0 8448 0>;
+		regulator-min-microvolt = <1016000>;
+		regulator-max-microvolt = <1114000>;
+		regulator-name = "vdd_logic";
+
+			      /* Voltage Duty-Cycle */
+		voltage-table = <1114000 0>,
+				<1095000 10>,
+				<1076000 20>,
+				<1056000 30>,
+				<1036000 40>,
+				<1016000 50>;
+	};