Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

4 files changed, 92 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt
new file mode 100644
index 000000000..cbaa6467a
--- /dev/null
+++ b/Documentation/devicetree/bindings/w1/fsl-imx-owire.txt
@@ -0,0 +1,18 @@
+* Freescale i.MX One wire bus master controller
+
+Required properties:
+- compatible : should be "fsl,imx21-owire"
+- reg : Address and length of the register set for the device
+
+Optional properties:
+- clocks : phandle of clock that supplies the module (required if platform
+		clock bindings use device tree)
+
+Example:
+
+- From imx53.dtsi:
+owire: owire@63fa4000 {
+	compatible = "fsl,imx53-owire", "fsl,imx21-owire";
+	reg = <0x63fa4000 0x4000>;
+	clocks = <&clks 159>;
+};
diff --git a/Documentation/devicetree/bindings/w1/omap-hdq.txt b/Documentation/devicetree/bindings/w1/omap-hdq.txt
new file mode 100644
index 000000000..913c5f91a
--- /dev/null
+++ b/Documentation/devicetree/bindings/w1/omap-hdq.txt
@@ -0,0 +1,22 @@
+* OMAP HDQ One wire bus master controller
+
+Required properties:
+- compatible : should be "ti,omap3-1w" or "ti,am4372-hdq"
+- reg : Address and length of the register set for the device
+- interrupts : interrupt line.
+- ti,hwmods : "hdq1w"
+
+Optional properties:
+- ti,mode: should be "hdq": HDQ mode  "1w": one-wire mode.
+	   If not specified HDQ mode is implied.
+
+Example:
+
+- From omap3.dtsi
+  hdqw1w: 1w@480b2000 {
+	compatible = "ti,omap3-1w";
+	reg = <0x480b2000 0x1000>;
+	interrupts = <58>;
+	ti,hwmods = "hdq1w";
+	ti,mode = "hdq";
+  };
diff --git a/Documentation/devicetree/bindings/w1/w1-gpio.txt b/Documentation/devicetree/bindings/w1/w1-gpio.txt
new file mode 100644
index 000000000..3d6554eac
--- /dev/null
+++ b/Documentation/devicetree/bindings/w1/w1-gpio.txt
@@ -0,0 +1,27 @@
+w1-gpio devicetree bindings
+
+Required properties:
+
+ - compatible: "w1-gpio"
+ - gpios: one or two GPIO specs:
+		- the first one is used as data I/O pin
+		- the second one is optional. If specified, it is used as
+		  enable pin for an external pin pullup.
+
+Optional properties:
+
+ - linux,open-drain: if specified, the data pin is considered in
+		     open-drain mode.
+
+Also refer to the generic w1.txt document.
+
+Examples:
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio 0 GPIO_ACTIVE_HIGH>;
+
+		battery {
+			// ...
+		};
+	};
diff --git a/Documentation/devicetree/bindings/w1/w1.txt b/Documentation/devicetree/bindings/w1/w1.txt
new file mode 100644
index 000000000..05f26b27d
--- /dev/null
+++ b/Documentation/devicetree/bindings/w1/w1.txt
@@ -0,0 +1,25 @@
+Generic devicetree bindings for onewire (w1) busses
+===================================================
+
+Onewire busses are described through nodes of their master bus controller.
+Slave devices are listed as sub-nodes of such master devices. For now, only
+one slave is allowed per bus master.
+
+
+Example:
+
+	charger: charger {
+		compatible = "gpio-charger";
+		charger-type = "mains";
+		gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
+	};
+
+	onewire {
+		compatible = "w1-gpio";
+		gpios = <&gpio 100 0>, <&gpio 101 0>;
+
+		battery {
+			compatible = "maxim,ds2760";
+			power-supplies = <&charger>;
+		};
+	};