Adding upstream version 4.19.249.upstream/4.19.249upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

13 files changed, 3674 insertions, 0 deletions

diff --git a/drivers/phy/samsung/Kconfig b/drivers/phy/samsung/Kconfig
new file mode 100644
index 000000000..2a5d33cb0
--- /dev/null
+++ b/drivers/phy/samsung/Kconfig
@@ -0,0 +1,95 @@
+#
+# Phy drivers for Samsung platforms
+#
+config PHY_EXYNOS_DP_VIDEO
+	tristate "EXYNOS SoC series Display Port PHY driver"
+	depends on OF
+	depends on ARCH_EXYNOS || COMPILE_TEST
+	default ARCH_EXYNOS
+	select GENERIC_PHY
+	help
+	  Support for Display Port PHY found on Samsung EXYNOS SoCs.
+
+config PHY_EXYNOS_MIPI_VIDEO
+	tristate "S5P/EXYNOS SoC series MIPI CSI-2/DSI PHY driver"
+	depends on HAS_IOMEM
+	depends on ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
+	select GENERIC_PHY
+	default y if ARCH_S5PV210 || ARCH_EXYNOS
+	help
+	  Support for MIPI CSI-2 and MIPI DSI DPHY found on Samsung S5P
+	  and EXYNOS SoCs.
+
+config PHY_EXYNOS_PCIE
+	bool "Exynos PCIe PHY driver"
+	depends on OF && (ARCH_EXYNOS || COMPILE_TEST)
+	select GENERIC_PHY
+	help
+	  Enable PCIe PHY support for Exynos SoC series.
+	  This driver provides PHY interface for Exynos PCIe controller.
+
+config PHY_SAMSUNG_USB2
+	tristate "Samsung USB 2.0 PHY driver"
+	depends on HAS_IOMEM
+	depends on USB_EHCI_EXYNOS || USB_OHCI_EXYNOS || USB_DWC2
+	select GENERIC_PHY
+	select MFD_SYSCON
+	default ARCH_EXYNOS
+	help
+	  Enable this to support the Samsung USB 2.0 PHY driver for Samsung
+	  SoCs. This driver provides the interface for USB 2.0 PHY. Support
+	  for particular PHYs will be enabled based on the SoC type in addition
+	  to this driver.
+
+config PHY_EXYNOS4210_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default CPU_EXYNOS4210
+
+config PHY_EXYNOS4X12_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default SOC_EXYNOS3250 || SOC_EXYNOS4412
+
+config PHY_EXYNOS5250_USB2
+	bool
+	depends on PHY_SAMSUNG_USB2
+	default SOC_EXYNOS5250 || SOC_EXYNOS5420
+
+config PHY_S5PV210_USB2
+	bool "Support for S5PV210"
+	depends on PHY_SAMSUNG_USB2
+	depends on ARCH_S5PV210
+	help
+	  Enable USB PHY support for S5PV210. This option requires that Samsung
+	  USB 2.0 PHY driver is enabled and means that support for this
+	  particular SoC is compiled in the driver. In case of S5PV210 two phys
+	  are available - device and host.
+
+config PHY_EXYNOS5_USBDRD
+	tristate "Exynos5 SoC series USB DRD PHY driver"
+	depends on ARCH_EXYNOS && OF
+	depends on HAS_IOMEM
+	depends on USB_DWC3_EXYNOS
+	select GENERIC_PHY
+	select MFD_SYSCON
+	default y
+	help
+	  Enable USB DRD PHY support for Exynos 5 SoC series.
+	  This driver provides PHY interface for USB 3.0 DRD controller
+	  present on Exynos5 SoC series.
+
+config PHY_EXYNOS5250_SATA
+	tristate "Exynos5250 Sata SerDes/PHY driver"
+	depends on SOC_EXYNOS5250
+	depends on HAS_IOMEM
+	depends on OF
+	select GENERIC_PHY
+	select I2C
+	select I2C_S3C2410
+	select MFD_SYSCON
+	help
+	  Enable this to support SATA SerDes/Phy found on Samsung's
+	  Exynos5250 based SoCs.This SerDes/Phy supports SATA 1.5 Gb/s,
+	  SATA 3.0 Gb/s, SATA 6.0 Gb/s speeds. It supports one SATA host
+	  port to accept one SATA device.
diff --git a/drivers/phy/samsung/Makefile b/drivers/phy/samsung/Makefile
new file mode 100644
index 000000000..db9b1aa0d
--- /dev/null
+++ b/drivers/phy/samsung/Makefile
@@ -0,0 +1,12 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-$(CONFIG_PHY_EXYNOS_DP_VIDEO)	+= phy-exynos-dp-video.o
+obj-$(CONFIG_PHY_EXYNOS_MIPI_VIDEO)	+= phy-exynos-mipi-video.o
+obj-$(CONFIG_PHY_EXYNOS_PCIE)		+= phy-exynos-pcie.o
+obj-$(CONFIG_PHY_SAMSUNG_USB2)		+= phy-exynos-usb2.o
+phy-exynos-usb2-y			+= phy-samsung-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4210_USB2)	+= phy-exynos4210-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS4X12_USB2)	+= phy-exynos4x12-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_EXYNOS5250_USB2)	+= phy-exynos5250-usb2.o
+phy-exynos-usb2-$(CONFIG_PHY_S5PV210_USB2)	+= phy-s5pv210-usb2.o
+obj-$(CONFIG_PHY_EXYNOS5_USBDRD)	+= phy-exynos5-usbdrd.o
+obj-$(CONFIG_PHY_EXYNOS5250_SATA)	+= phy-exynos5250-sata.o
diff --git a/drivers/phy/samsung/phy-exynos-dp-video.c b/drivers/phy/samsung/phy-exynos-dp-video.c
new file mode 100644
index 000000000..2dd6dd1f3
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos-dp-video.c
@@ -0,0 +1,121 @@
+/*
+ * Samsung EXYNOS SoC series Display Port PHY driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Jingoo Han <jg1.han@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/soc/samsung/exynos-regs-pmu.h>
+
+struct exynos_dp_video_phy_drvdata {
+	u32 phy_ctrl_offset;
+};
+
+struct exynos_dp_video_phy {
+	struct regmap *regs;
+	const struct exynos_dp_video_phy_drvdata *drvdata;
+};
+
+static int exynos_dp_video_phy_power_on(struct phy *phy)
+{
+	struct exynos_dp_video_phy *state = phy_get_drvdata(phy);
+
+	/* Disable power isolation on DP-PHY */
+	return regmap_update_bits(state->regs, state->drvdata->phy_ctrl_offset,
+				  EXYNOS4_PHY_ENABLE, EXYNOS4_PHY_ENABLE);
+}
+
+static int exynos_dp_video_phy_power_off(struct phy *phy)
+{
+	struct exynos_dp_video_phy *state = phy_get_drvdata(phy);
+
+	/* Enable power isolation on DP-PHY */
+	return regmap_update_bits(state->regs, state->drvdata->phy_ctrl_offset,
+				  EXYNOS4_PHY_ENABLE, 0);
+}
+
+static const struct phy_ops exynos_dp_video_phy_ops = {
+	.power_on	= exynos_dp_video_phy_power_on,
+	.power_off	= exynos_dp_video_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static const struct exynos_dp_video_phy_drvdata exynos5250_dp_video_phy = {
+	.phy_ctrl_offset	= EXYNOS5_DPTX_PHY_CONTROL,
+};
+
+static const struct exynos_dp_video_phy_drvdata exynos5420_dp_video_phy = {
+	.phy_ctrl_offset	= EXYNOS5420_DPTX_PHY_CONTROL,
+};
+
+static const struct of_device_id exynos_dp_video_phy_of_match[] = {
+	{
+		.compatible = "samsung,exynos5250-dp-video-phy",
+		.data = &exynos5250_dp_video_phy,
+	}, {
+		.compatible = "samsung,exynos5420-dp-video-phy",
+		.data = &exynos5420_dp_video_phy,
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, exynos_dp_video_phy_of_match);
+
+static int exynos_dp_video_phy_probe(struct platform_device *pdev)
+{
+	struct exynos_dp_video_phy *state;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	struct phy *phy;
+
+	state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
+	if (!state)
+		return -ENOMEM;
+
+	state->regs = syscon_regmap_lookup_by_phandle(dev->of_node,
+						      "samsung,pmu-syscon");
+	if (IS_ERR(state->regs)) {
+		dev_err(dev, "Failed to lookup PMU regmap\n");
+		return PTR_ERR(state->regs);
+	}
+
+	state->drvdata = of_device_get_match_data(dev);
+
+	phy = devm_phy_create(dev, NULL, &exynos_dp_video_phy_ops);
+	if (IS_ERR(phy)) {
+		dev_err(dev, "failed to create Display Port PHY\n");
+		return PTR_ERR(phy);
+	}
+	phy_set_drvdata(phy, state);
+
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver exynos_dp_video_phy_driver = {
+	.probe	= exynos_dp_video_phy_probe,
+	.driver = {
+		.name	= "exynos-dp-video-phy",
+		.of_match_table	= exynos_dp_video_phy_of_match,
+	}
+};
+module_platform_driver(exynos_dp_video_phy_driver);
+
+MODULE_AUTHOR("Jingoo Han <jg1.han@samsung.com>");
+MODULE_DESCRIPTION("Samsung EXYNOS SoC DP PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/samsung/phy-exynos-mipi-video.c b/drivers/phy/samsung/phy-exynos-mipi-video.c
new file mode 100644
index 000000000..00d89599c
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos-mipi-video.c
@@ -0,0 +1,371 @@
+/*
+ * Samsung S5P/EXYNOS SoC series MIPI CSIS/DSIM DPHY driver
+ *
+ * Copyright (C) 2013,2016 Samsung Electronics Co., Ltd.
+ * Author: Sylwester Nawrocki <s.nawrocki@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include <linux/spinlock.h>
+#include <linux/soc/samsung/exynos-regs-pmu.h>
+#include <linux/mfd/syscon.h>
+
+enum exynos_mipi_phy_id {
+	EXYNOS_MIPI_PHY_ID_NONE = -1,
+	EXYNOS_MIPI_PHY_ID_CSIS0,
+	EXYNOS_MIPI_PHY_ID_DSIM0,
+	EXYNOS_MIPI_PHY_ID_CSIS1,
+	EXYNOS_MIPI_PHY_ID_DSIM1,
+	EXYNOS_MIPI_PHY_ID_CSIS2,
+	EXYNOS_MIPI_PHYS_NUM
+};
+
+enum exynos_mipi_phy_regmap_id {
+	EXYNOS_MIPI_REGMAP_PMU,
+	EXYNOS_MIPI_REGMAP_DISP,
+	EXYNOS_MIPI_REGMAP_CAM0,
+	EXYNOS_MIPI_REGMAP_CAM1,
+	EXYNOS_MIPI_REGMAPS_NUM
+};
+
+struct mipi_phy_device_desc {
+	int num_phys;
+	int num_regmaps;
+	const char *regmap_names[EXYNOS_MIPI_REGMAPS_NUM];
+	struct exynos_mipi_phy_desc {
+		enum exynos_mipi_phy_id	coupled_phy_id;
+		u32 enable_val;
+		unsigned int enable_reg;
+		enum exynos_mipi_phy_regmap_id enable_map;
+		u32 resetn_val;
+		unsigned int resetn_reg;
+		enum exynos_mipi_phy_regmap_id resetn_map;
+	} phys[EXYNOS_MIPI_PHYS_NUM];
+};
+
+static const struct mipi_phy_device_desc s5pv210_mipi_phy = {
+	.num_regmaps = 1,
+	.regmap_names = {"syscon"},
+	.num_phys = 4,
+	.phys = {
+		{
+			/* EXYNOS_MIPI_PHY_ID_CSIS0 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_DSIM0,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(0),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_SRESETN,
+			.resetn_reg = EXYNOS4_MIPI_PHY_CONTROL(0),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_DSIM0 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_CSIS0,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(0),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_MRESETN,
+			.resetn_reg = EXYNOS4_MIPI_PHY_CONTROL(0),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_CSIS1 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_DSIM1,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(1),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_SRESETN,
+			.resetn_reg = EXYNOS4_MIPI_PHY_CONTROL(1),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_DSIM1 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_CSIS1,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(1),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_MRESETN,
+			.resetn_reg = EXYNOS4_MIPI_PHY_CONTROL(1),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		},
+	},
+};
+
+static const struct mipi_phy_device_desc exynos5420_mipi_phy = {
+	.num_regmaps = 1,
+	.regmap_names = {"syscon"},
+	.num_phys = 5,
+	.phys = {
+		{
+			/* EXYNOS_MIPI_PHY_ID_CSIS0 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_DSIM0,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS5420_MIPI_PHY_CONTROL(0),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_SRESETN,
+			.resetn_reg = EXYNOS5420_MIPI_PHY_CONTROL(0),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_DSIM0 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_CSIS0,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS5420_MIPI_PHY_CONTROL(0),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_MRESETN,
+			.resetn_reg = EXYNOS5420_MIPI_PHY_CONTROL(0),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_CSIS1 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_DSIM1,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS5420_MIPI_PHY_CONTROL(1),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_SRESETN,
+			.resetn_reg = EXYNOS5420_MIPI_PHY_CONTROL(1),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_DSIM1 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_CSIS1,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS5420_MIPI_PHY_CONTROL(1),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_MRESETN,
+			.resetn_reg = EXYNOS5420_MIPI_PHY_CONTROL(1),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_CSIS2 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_NONE,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS5420_MIPI_PHY_CONTROL(2),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = EXYNOS4_MIPI_PHY_SRESETN,
+			.resetn_reg = EXYNOS5420_MIPI_PHY_CONTROL(2),
+			.resetn_map = EXYNOS_MIPI_REGMAP_PMU,
+		},
+	},
+};
+
+#define EXYNOS5433_SYSREG_DISP_MIPI_PHY		0x100C
+#define EXYNOS5433_SYSREG_CAM0_MIPI_DPHY_CON	0x1014
+#define EXYNOS5433_SYSREG_CAM1_MIPI_DPHY_CON	0x1020
+
+static const struct mipi_phy_device_desc exynos5433_mipi_phy = {
+	.num_regmaps = 4,
+	.regmap_names = {
+		"samsung,pmu-syscon",
+		"samsung,disp-sysreg",
+		"samsung,cam0-sysreg",
+		"samsung,cam1-sysreg"
+	},
+	.num_phys = 5,
+	.phys = {
+		{
+			/* EXYNOS_MIPI_PHY_ID_CSIS0 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_DSIM0,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(0),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = BIT(0),
+			.resetn_reg = EXYNOS5433_SYSREG_CAM0_MIPI_DPHY_CON,
+			.resetn_map = EXYNOS_MIPI_REGMAP_CAM0,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_DSIM0 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_CSIS0,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(0),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = BIT(0),
+			.resetn_reg = EXYNOS5433_SYSREG_DISP_MIPI_PHY,
+			.resetn_map = EXYNOS_MIPI_REGMAP_DISP,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_CSIS1 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_NONE,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(1),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = BIT(1),
+			.resetn_reg = EXYNOS5433_SYSREG_CAM0_MIPI_DPHY_CON,
+			.resetn_map = EXYNOS_MIPI_REGMAP_CAM0,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_DSIM1 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_NONE,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(1),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = BIT(1),
+			.resetn_reg = EXYNOS5433_SYSREG_DISP_MIPI_PHY,
+			.resetn_map = EXYNOS_MIPI_REGMAP_DISP,
+		}, {
+			/* EXYNOS_MIPI_PHY_ID_CSIS2 */
+			.coupled_phy_id = EXYNOS_MIPI_PHY_ID_NONE,
+			.enable_val = EXYNOS4_PHY_ENABLE,
+			.enable_reg = EXYNOS4_MIPI_PHY_CONTROL(2),
+			.enable_map = EXYNOS_MIPI_REGMAP_PMU,
+			.resetn_val = BIT(0),
+			.resetn_reg = EXYNOS5433_SYSREG_CAM1_MIPI_DPHY_CON,
+			.resetn_map = EXYNOS_MIPI_REGMAP_CAM1,
+		},
+	},
+};
+
+struct exynos_mipi_video_phy {
+	struct regmap *regmaps[EXYNOS_MIPI_REGMAPS_NUM];
+	int num_phys;
+	struct video_phy_desc {
+		struct phy *phy;
+		unsigned int index;
+		const struct exynos_mipi_phy_desc *data;
+	} phys[EXYNOS_MIPI_PHYS_NUM];
+	spinlock_t slock;
+};
+
+static int __set_phy_state(const struct exynos_mipi_phy_desc *data,
+			   struct exynos_mipi_video_phy *state, unsigned int on)
+{
+	struct regmap *enable_map = state->regmaps[data->enable_map];
+	struct regmap *resetn_map = state->regmaps[data->resetn_map];
+
+	spin_lock(&state->slock);
+
+	/* disable in PMU sysreg */
+	if (!on && data->coupled_phy_id >= 0 &&
+	    state->phys[data->coupled_phy_id].phy->power_count == 0)
+		regmap_update_bits(enable_map, data->enable_reg,
+				   data->enable_val, 0);
+	/* PHY reset */
+	if (on)
+		regmap_update_bits(resetn_map, data->resetn_reg,
+				   data->resetn_val, data->resetn_val);
+	else
+		regmap_update_bits(resetn_map, data->resetn_reg,
+				   data->resetn_val, 0);
+	/* enable in PMU sysreg */
+	if (on)
+		regmap_update_bits(enable_map, data->enable_reg,
+				   data->enable_val, data->enable_val);
+
+	spin_unlock(&state->slock);
+
+	return 0;
+}
+
+#define to_mipi_video_phy(desc) \
+	container_of((desc), struct exynos_mipi_video_phy, phys[(desc)->index])
+
+static int exynos_mipi_video_phy_power_on(struct phy *phy)
+{
+	struct video_phy_desc *phy_desc = phy_get_drvdata(phy);
+	struct exynos_mipi_video_phy *state = to_mipi_video_phy(phy_desc);
+
+	return __set_phy_state(phy_desc->data, state, 1);
+}
+
+static int exynos_mipi_video_phy_power_off(struct phy *phy)
+{
+	struct video_phy_desc *phy_desc = phy_get_drvdata(phy);
+	struct exynos_mipi_video_phy *state = to_mipi_video_phy(phy_desc);
+
+	return __set_phy_state(phy_desc->data, state, 0);
+}
+
+static struct phy *exynos_mipi_video_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct exynos_mipi_video_phy *state = dev_get_drvdata(dev);
+
+	if (WARN_ON(args->args[0] >= state->num_phys))
+		return ERR_PTR(-ENODEV);
+
+	return state->phys[args->args[0]].phy;
+}
+
+static const struct phy_ops exynos_mipi_video_phy_ops = {
+	.power_on	= exynos_mipi_video_phy_power_on,
+	.power_off	= exynos_mipi_video_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int exynos_mipi_video_phy_probe(struct platform_device *pdev)
+{
+	const struct mipi_phy_device_desc *phy_dev;
+	struct exynos_mipi_video_phy *state;
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct phy_provider *phy_provider;
+	unsigned int i;
+
+	phy_dev = of_device_get_match_data(dev);
+	if (!phy_dev)
+		return -ENODEV;
+
+	state = devm_kzalloc(dev, sizeof(*state), GFP_KERNEL);
+	if (!state)
+		return -ENOMEM;
+
+	for (i = 0; i < phy_dev->num_regmaps; i++) {
+		state->regmaps[i] = syscon_regmap_lookup_by_phandle(np,
+						phy_dev->regmap_names[i]);
+		if (IS_ERR(state->regmaps[i]))
+			return PTR_ERR(state->regmaps[i]);
+	}
+	state->num_phys = phy_dev->num_phys;
+	spin_lock_init(&state->slock);
+
+	dev_set_drvdata(dev, state);
+
+	for (i = 0; i < state->num_phys; i++) {
+		struct phy *phy = devm_phy_create(dev, NULL,
+						  &exynos_mipi_video_phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "failed to create PHY %d\n", i);
+			return PTR_ERR(phy);
+		}
+
+		state->phys[i].phy = phy;
+		state->phys[i].index = i;
+		state->phys[i].data = &phy_dev->phys[i];
+		phy_set_drvdata(phy, &state->phys[i]);
+	}
+
+	phy_provider = devm_of_phy_provider_register(dev,
+					exynos_mipi_video_phy_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static const struct of_device_id exynos_mipi_video_phy_of_match[] = {
+	{
+		.compatible = "samsung,s5pv210-mipi-video-phy",
+		.data = &s5pv210_mipi_phy,
+	}, {
+		.compatible = "samsung,exynos5420-mipi-video-phy",
+		.data = &exynos5420_mipi_phy,
+	}, {
+		.compatible = "samsung,exynos5433-mipi-video-phy",
+		.data = &exynos5433_mipi_phy,
+	},
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, exynos_mipi_video_phy_of_match);
+
+static struct platform_driver exynos_mipi_video_phy_driver = {
+	.probe	= exynos_mipi_video_phy_probe,
+	.driver = {
+		.of_match_table	= exynos_mipi_video_phy_of_match,
+		.name  = "exynos-mipi-video-phy",
+	}
+};
+module_platform_driver(exynos_mipi_video_phy_driver);
+
+MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC MIPI CSI-2/DSI PHY driver");
+MODULE_AUTHOR("Sylwester Nawrocki <s.nawrocki@samsung.com>");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/samsung/phy-exynos-pcie.c b/drivers/phy/samsung/phy-exynos-pcie.c
new file mode 100644
index 000000000..a89c12faf
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos-pcie.c
@@ -0,0 +1,281 @@
+/*
+ * Samsung EXYNOS SoC series PCIe PHY driver
+ *
+ * Phy provider for PCIe controller on Exynos SoC series
+ *
+ * Copyright (C) 2017 Samsung Electronics Co., Ltd.
+ * Jaehoon Chung <jh80.chung@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/init.h>
+#include <linux/mfd/syscon.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+
+/* PCIe Purple registers */
+#define PCIE_PHY_GLOBAL_RESET		0x000
+#define PCIE_PHY_COMMON_RESET		0x004
+#define PCIE_PHY_CMN_REG		0x008
+#define PCIE_PHY_MAC_RESET		0x00c
+#define PCIE_PHY_PLL_LOCKED		0x010
+#define PCIE_PHY_TRSVREG_RESET		0x020
+#define PCIE_PHY_TRSV_RESET		0x024
+
+/* PCIe PHY registers */
+#define PCIE_PHY_IMPEDANCE		0x004
+#define PCIE_PHY_PLL_DIV_0		0x008
+#define PCIE_PHY_PLL_BIAS		0x00c
+#define PCIE_PHY_DCC_FEEDBACK		0x014
+#define PCIE_PHY_PLL_DIV_1		0x05c
+#define PCIE_PHY_COMMON_POWER		0x064
+#define PCIE_PHY_COMMON_PD_CMN		BIT(3)
+#define PCIE_PHY_TRSV0_EMP_LVL		0x084
+#define PCIE_PHY_TRSV0_DRV_LVL		0x088
+#define PCIE_PHY_TRSV0_RXCDR		0x0ac
+#define PCIE_PHY_TRSV0_POWER		0x0c4
+#define PCIE_PHY_TRSV0_PD_TSV		BIT(7)
+#define PCIE_PHY_TRSV0_LVCC		0x0dc
+#define PCIE_PHY_TRSV1_EMP_LVL		0x144
+#define PCIE_PHY_TRSV1_RXCDR		0x16c
+#define PCIE_PHY_TRSV1_POWER		0x184
+#define PCIE_PHY_TRSV1_PD_TSV		BIT(7)
+#define PCIE_PHY_TRSV1_LVCC		0x19c
+#define PCIE_PHY_TRSV2_EMP_LVL		0x204
+#define PCIE_PHY_TRSV2_RXCDR		0x22c
+#define PCIE_PHY_TRSV2_POWER		0x244
+#define PCIE_PHY_TRSV2_PD_TSV		BIT(7)
+#define PCIE_PHY_TRSV2_LVCC		0x25c
+#define PCIE_PHY_TRSV3_EMP_LVL		0x2c4
+#define PCIE_PHY_TRSV3_RXCDR		0x2ec
+#define PCIE_PHY_TRSV3_POWER		0x304
+#define PCIE_PHY_TRSV3_PD_TSV		BIT(7)
+#define PCIE_PHY_TRSV3_LVCC		0x31c
+
+struct exynos_pcie_phy_data {
+	const struct phy_ops	*ops;
+};
+
+/* For Exynos pcie phy */
+struct exynos_pcie_phy {
+	const struct exynos_pcie_phy_data *drv_data;
+	void __iomem *phy_base;
+	void __iomem *blk_base; /* For exynos5440 */
+};
+
+static void exynos_pcie_phy_writel(void __iomem *base, u32 val, u32 offset)
+{
+	writel(val, base + offset);
+}
+
+static u32 exynos_pcie_phy_readl(void __iomem *base, u32 offset)
+{
+	return readl(base + offset);
+}
+
+/* For Exynos5440 specific functions */
+static int exynos5440_pcie_phy_init(struct phy *phy)
+{
+	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
+
+	/* DCC feedback control off */
+	exynos_pcie_phy_writel(ep->phy_base, 0x29, PCIE_PHY_DCC_FEEDBACK);
+
+	/* set TX/RX impedance */
+	exynos_pcie_phy_writel(ep->phy_base, 0xd5, PCIE_PHY_IMPEDANCE);
+
+	/* set 50Mhz PHY clock */
+	exynos_pcie_phy_writel(ep->phy_base, 0x14, PCIE_PHY_PLL_DIV_0);
+	exynos_pcie_phy_writel(ep->phy_base, 0x12, PCIE_PHY_PLL_DIV_1);
+
+	/* set TX Differential output for lane 0 */
+	exynos_pcie_phy_writel(ep->phy_base, 0x7f, PCIE_PHY_TRSV0_DRV_LVL);
+
+	/* set TX Pre-emphasis Level Control for lane 0 to minimum */
+	exynos_pcie_phy_writel(ep->phy_base, 0x0, PCIE_PHY_TRSV0_EMP_LVL);
+
+	/* set RX clock and data recovery bandwidth */
+	exynos_pcie_phy_writel(ep->phy_base, 0xe7, PCIE_PHY_PLL_BIAS);
+	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV0_RXCDR);
+	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV1_RXCDR);
+	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV2_RXCDR);
+	exynos_pcie_phy_writel(ep->phy_base, 0x82, PCIE_PHY_TRSV3_RXCDR);
+
+	/* change TX Pre-emphasis Level Control for lanes */
+	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV0_EMP_LVL);
+	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV1_EMP_LVL);
+	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV2_EMP_LVL);
+	exynos_pcie_phy_writel(ep->phy_base, 0x39, PCIE_PHY_TRSV3_EMP_LVL);
+
+	/* set LVCC */
+	exynos_pcie_phy_writel(ep->phy_base, 0x20, PCIE_PHY_TRSV0_LVCC);
+	exynos_pcie_phy_writel(ep->phy_base, 0xa0, PCIE_PHY_TRSV1_LVCC);
+	exynos_pcie_phy_writel(ep->phy_base, 0xa0, PCIE_PHY_TRSV2_LVCC);
+	exynos_pcie_phy_writel(ep->phy_base, 0xa0, PCIE_PHY_TRSV3_LVCC);
+
+	/* pulse for common reset */
+	exynos_pcie_phy_writel(ep->blk_base, 1, PCIE_PHY_COMMON_RESET);
+	udelay(500);
+	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_COMMON_RESET);
+
+	return 0;
+}
+
+static int exynos5440_pcie_phy_power_on(struct phy *phy)
+{
+	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
+	u32 val;
+
+	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_COMMON_RESET);
+	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_CMN_REG);
+	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_TRSVREG_RESET);
+	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_TRSV_RESET);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_COMMON_POWER);
+	val &= ~PCIE_PHY_COMMON_PD_CMN;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_COMMON_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV0_POWER);
+	val &= ~PCIE_PHY_TRSV0_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV0_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV1_POWER);
+	val &= ~PCIE_PHY_TRSV1_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV1_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV2_POWER);
+	val &= ~PCIE_PHY_TRSV2_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV2_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV3_POWER);
+	val &= ~PCIE_PHY_TRSV3_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV3_POWER);
+
+	return 0;
+}
+
+static int exynos5440_pcie_phy_power_off(struct phy *phy)
+{
+	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
+	u32 val;
+
+	if (readl_poll_timeout(ep->phy_base + PCIE_PHY_PLL_LOCKED, val,
+				(val != 0), 1, 500)) {
+		dev_err(&phy->dev, "PLL Locked: 0x%x\n", val);
+		return -ETIMEDOUT;
+	}
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_COMMON_POWER);
+	val |= PCIE_PHY_COMMON_PD_CMN;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_COMMON_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV0_POWER);
+	val |= PCIE_PHY_TRSV0_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV0_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV1_POWER);
+	val |= PCIE_PHY_TRSV1_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV1_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV2_POWER);
+	val |= PCIE_PHY_TRSV2_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV2_POWER);
+
+	val = exynos_pcie_phy_readl(ep->phy_base, PCIE_PHY_TRSV3_POWER);
+	val |= PCIE_PHY_TRSV3_PD_TSV;
+	exynos_pcie_phy_writel(ep->phy_base, val, PCIE_PHY_TRSV3_POWER);
+
+	return 0;
+}
+
+static int exynos5440_pcie_phy_reset(struct phy *phy)
+{
+	struct exynos_pcie_phy *ep = phy_get_drvdata(phy);
+
+	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_MAC_RESET);
+	exynos_pcie_phy_writel(ep->blk_base, 1, PCIE_PHY_GLOBAL_RESET);
+	exynos_pcie_phy_writel(ep->blk_base, 0, PCIE_PHY_GLOBAL_RESET);
+
+	return 0;
+}
+
+static const struct phy_ops exynos5440_phy_ops = {
+	.init		= exynos5440_pcie_phy_init,
+	.power_on	= exynos5440_pcie_phy_power_on,
+	.power_off	= exynos5440_pcie_phy_power_off,
+	.reset		= exynos5440_pcie_phy_reset,
+	.owner		= THIS_MODULE,
+};
+
+static const struct exynos_pcie_phy_data exynos5440_pcie_phy_data = {
+	.ops		= &exynos5440_phy_ops,
+};
+
+static const struct of_device_id exynos_pcie_phy_match[] = {
+	{
+		.compatible = "samsung,exynos5440-pcie-phy",
+		.data = &exynos5440_pcie_phy_data,
+	},
+	{},
+};
+
+static int exynos_pcie_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct exynos_pcie_phy *exynos_phy;
+	struct phy *generic_phy;
+	struct phy_provider *phy_provider;
+	struct resource *res;
+	const struct exynos_pcie_phy_data *drv_data;
+
+	drv_data = of_device_get_match_data(dev);
+	if (!drv_data)
+		return -ENODEV;
+
+	exynos_phy = devm_kzalloc(dev, sizeof(*exynos_phy), GFP_KERNEL);
+	if (!exynos_phy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	exynos_phy->phy_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(exynos_phy->phy_base))
+		return PTR_ERR(exynos_phy->phy_base);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	exynos_phy->blk_base = devm_ioremap_resource(dev, res);
+	if (IS_ERR(exynos_phy->blk_base))
+		return PTR_ERR(exynos_phy->blk_base);
+
+	exynos_phy->drv_data = drv_data;
+
+	generic_phy = devm_phy_create(dev, dev->of_node, drv_data->ops);
+	if (IS_ERR(generic_phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		return PTR_ERR(generic_phy);
+	}
+
+	phy_set_drvdata(generic_phy, exynos_phy);
+	phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static struct platform_driver exynos_pcie_phy_driver = {
+	.probe	= exynos_pcie_phy_probe,
+	.driver = {
+		.of_match_table	= exynos_pcie_phy_match,
+		.name		= "exynos_pcie_phy",
+	}
+};
+
+builtin_platform_driver(exynos_pcie_phy_driver);
diff --git a/drivers/phy/samsung/phy-exynos4210-usb2.c b/drivers/phy/samsung/phy-exynos4210-usb2.c
new file mode 100644
index 000000000..1f50e1004
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos4210-usb2.c
@@ -0,0 +1,260 @@
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4210 support
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include "phy-samsung-usb2.h"
+
+/* Exynos USB PHY registers */
+
+/* PHY power control */
+#define EXYNOS_4210_UPHYPWR			0x0
+
+#define EXYNOS_4210_UPHYPWR_PHY0_SUSPEND	BIT(0)
+#define EXYNOS_4210_UPHYPWR_PHY0_PWR		BIT(3)
+#define EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR	BIT(4)
+#define EXYNOS_4210_UPHYPWR_PHY0_SLEEP		BIT(5)
+#define EXYNOS_4210_UPHYPWR_PHY0	( \
+	EXYNOS_4210_UPHYPWR_PHY0_SUSPEND | \
+	EXYNOS_4210_UPHYPWR_PHY0_PWR | \
+	EXYNOS_4210_UPHYPWR_PHY0_OTG_PWR | \
+	EXYNOS_4210_UPHYPWR_PHY0_SLEEP)
+
+#define EXYNOS_4210_UPHYPWR_PHY1_SUSPEND	BIT(6)
+#define EXYNOS_4210_UPHYPWR_PHY1_PWR		BIT(7)
+#define EXYNOS_4210_UPHYPWR_PHY1_SLEEP		BIT(8)
+#define EXYNOS_4210_UPHYPWR_PHY1 ( \
+	EXYNOS_4210_UPHYPWR_PHY1_SUSPEND | \
+	EXYNOS_4210_UPHYPWR_PHY1_PWR | \
+	EXYNOS_4210_UPHYPWR_PHY1_SLEEP)
+
+#define EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND	BIT(9)
+#define EXYNOS_4210_UPHYPWR_HSIC0_SLEEP		BIT(10)
+#define EXYNOS_4210_UPHYPWR_HSIC0 ( \
+	EXYNOS_4210_UPHYPWR_HSIC0_SUSPEND | \
+	EXYNOS_4210_UPHYPWR_HSIC0_SLEEP)
+
+#define EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND	BIT(11)
+#define EXYNOS_4210_UPHYPWR_HSIC1_SLEEP		BIT(12)
+#define EXYNOS_4210_UPHYPWR_HSIC1 ( \
+	EXYNOS_4210_UPHYPWR_HSIC1_SUSPEND | \
+	EXYNOS_4210_UPHYPWR_HSIC1_SLEEP)
+
+/* PHY clock control */
+#define EXYNOS_4210_UPHYCLK			0x4
+
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_MASK	(0x3 << 0)
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET	0
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ	(0x0 << 0)
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ	(0x3 << 0)
+#define EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ	(0x2 << 0)
+
+#define EXYNOS_4210_UPHYCLK_PHY0_ID_PULLUP	BIT(2)
+#define EXYNOS_4210_UPHYCLK_PHY0_COMMON_ON	BIT(4)
+#define EXYNOS_4210_UPHYCLK_PHY1_COMMON_ON	BIT(7)
+
+/* PHY reset control */
+#define EXYNOS_4210_UPHYRST			0x8
+
+#define EXYNOS_4210_URSTCON_PHY0		BIT(0)
+#define EXYNOS_4210_URSTCON_OTG_HLINK		BIT(1)
+#define EXYNOS_4210_URSTCON_OTG_PHYLINK		BIT(2)
+#define EXYNOS_4210_URSTCON_PHY1_ALL		BIT(3)
+#define EXYNOS_4210_URSTCON_PHY1_P0		BIT(4)
+#define EXYNOS_4210_URSTCON_PHY1_P1P2		BIT(5)
+#define EXYNOS_4210_URSTCON_HOST_LINK_ALL	BIT(6)
+#define EXYNOS_4210_URSTCON_HOST_LINK_P0	BIT(7)
+#define EXYNOS_4210_URSTCON_HOST_LINK_P1	BIT(8)
+#define EXYNOS_4210_URSTCON_HOST_LINK_P2	BIT(9)
+
+/* Isolation, configured in the power management unit */
+#define EXYNOS_4210_USB_ISOL_DEVICE_OFFSET	0x704
+#define EXYNOS_4210_USB_ISOL_DEVICE		BIT(0)
+#define EXYNOS_4210_USB_ISOL_HOST_OFFSET	0x708
+#define EXYNOS_4210_USB_ISOL_HOST		BIT(0)
+
+/* USBYPHY1 Floating prevention */
+#define EXYNOS_4210_UPHY1CON			0x34
+#define EXYNOS_4210_UPHY1CON_FLOAT_PREVENTION	0x1
+
+/* Mode switching SUB Device <-> Host */
+#define EXYNOS_4210_MODE_SWITCH_OFFSET		0x21c
+#define EXYNOS_4210_MODE_SWITCH_MASK		1
+#define EXYNOS_4210_MODE_SWITCH_DEVICE		0
+#define EXYNOS_4210_MODE_SWITCH_HOST		1
+
+enum exynos4210_phy_id {
+	EXYNOS4210_DEVICE,
+	EXYNOS4210_HOST,
+	EXYNOS4210_HSIC0,
+	EXYNOS4210_HSIC1,
+	EXYNOS4210_NUM_PHYS,
+};
+
+/*
+ * exynos4210_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static int exynos4210_rate_to_clk(unsigned long rate, u32 *reg)
+{
+	switch (rate) {
+	case 12 * MHZ:
+		*reg = EXYNOS_4210_UPHYCLK_PHYFSEL_12MHZ;
+		break;
+	case 24 * MHZ:
+		*reg = EXYNOS_4210_UPHYCLK_PHYFSEL_24MHZ;
+		break;
+	case 48 * MHZ:
+		*reg = EXYNOS_4210_UPHYCLK_PHYFSEL_48MHZ;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void exynos4210_isol(struct samsung_usb2_phy_instance *inst, bool on)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 offset;
+	u32 mask;
+
+	switch (inst->cfg->id) {
+	case EXYNOS4210_DEVICE:
+		offset = EXYNOS_4210_USB_ISOL_DEVICE_OFFSET;
+		mask = EXYNOS_4210_USB_ISOL_DEVICE;
+		break;
+	case EXYNOS4210_HOST:
+		offset = EXYNOS_4210_USB_ISOL_HOST_OFFSET;
+		mask = EXYNOS_4210_USB_ISOL_HOST;
+		break;
+	default:
+		return;
+	}
+
+	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
+}
+
+static void exynos4210_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 rstbits = 0;
+	u32 phypwr = 0;
+	u32 rst;
+	u32 pwr;
+	u32 clk;
+
+	switch (inst->cfg->id) {
+	case EXYNOS4210_DEVICE:
+		phypwr =	EXYNOS_4210_UPHYPWR_PHY0;
+		rstbits =	EXYNOS_4210_URSTCON_PHY0;
+		break;
+	case EXYNOS4210_HOST:
+		phypwr =	EXYNOS_4210_UPHYPWR_PHY1;
+		rstbits =	EXYNOS_4210_URSTCON_PHY1_ALL |
+				EXYNOS_4210_URSTCON_PHY1_P0 |
+				EXYNOS_4210_URSTCON_PHY1_P1P2 |
+				EXYNOS_4210_URSTCON_HOST_LINK_ALL |
+				EXYNOS_4210_URSTCON_HOST_LINK_P0;
+		writel(on, drv->reg_phy + EXYNOS_4210_UPHY1CON);
+		break;
+	case EXYNOS4210_HSIC0:
+		phypwr =	EXYNOS_4210_UPHYPWR_HSIC0;
+		rstbits =	EXYNOS_4210_URSTCON_PHY1_P1P2 |
+				EXYNOS_4210_URSTCON_HOST_LINK_P1;
+		break;
+	case EXYNOS4210_HSIC1:
+		phypwr =	EXYNOS_4210_UPHYPWR_HSIC1;
+		rstbits =	EXYNOS_4210_URSTCON_PHY1_P1P2 |
+				EXYNOS_4210_URSTCON_HOST_LINK_P2;
+		break;
+	}
+
+	if (on) {
+		clk = readl(drv->reg_phy + EXYNOS_4210_UPHYCLK);
+		clk &= ~EXYNOS_4210_UPHYCLK_PHYFSEL_MASK;
+		clk |= drv->ref_reg_val << EXYNOS_4210_UPHYCLK_PHYFSEL_OFFSET;
+		writel(clk, drv->reg_phy + EXYNOS_4210_UPHYCLK);
+
+		pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
+		pwr &= ~phypwr;
+		writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
+
+		rst = readl(drv->reg_phy + EXYNOS_4210_UPHYRST);
+		rst |= rstbits;
+		writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
+		udelay(10);
+		rst &= ~rstbits;
+		writel(rst, drv->reg_phy + EXYNOS_4210_UPHYRST);
+		/* The following delay is necessary for the reset sequence to be
+		 * completed */
+		udelay(80);
+	} else {
+		pwr = readl(drv->reg_phy + EXYNOS_4210_UPHYPWR);
+		pwr |= phypwr;
+		writel(pwr, drv->reg_phy + EXYNOS_4210_UPHYPWR);
+	}
+}
+
+static int exynos4210_power_on(struct samsung_usb2_phy_instance *inst)
+{
+	/* Order of initialisation is important - first power then isolation */
+	exynos4210_phy_pwr(inst, 1);
+	exynos4210_isol(inst, 0);
+
+	return 0;
+}
+
+static int exynos4210_power_off(struct samsung_usb2_phy_instance *inst)
+{
+	exynos4210_isol(inst, 1);
+	exynos4210_phy_pwr(inst, 0);
+
+	return 0;
+}
+
+
+static const struct samsung_usb2_common_phy exynos4210_phys[] = {
+	{
+		.label		= "device",
+		.id		= EXYNOS4210_DEVICE,
+		.power_on	= exynos4210_power_on,
+		.power_off	= exynos4210_power_off,
+	},
+	{
+		.label		= "host",
+		.id		= EXYNOS4210_HOST,
+		.power_on	= exynos4210_power_on,
+		.power_off	= exynos4210_power_off,
+	},
+	{
+		.label		= "hsic0",
+		.id		= EXYNOS4210_HSIC0,
+		.power_on	= exynos4210_power_on,
+		.power_off	= exynos4210_power_off,
+	},
+	{
+		.label		= "hsic1",
+		.id		= EXYNOS4210_HSIC1,
+		.power_on	= exynos4210_power_on,
+		.power_off	= exynos4210_power_off,
+	},
+};
+
+const struct samsung_usb2_phy_config exynos4210_usb2_phy_config = {
+	.has_mode_switch	= 0,
+	.num_phys		= EXYNOS4210_NUM_PHYS,
+	.phys			= exynos4210_phys,
+	.rate_to_clk		= exynos4210_rate_to_clk,
+};
diff --git a/drivers/phy/samsung/phy-exynos4x12-usb2.c b/drivers/phy/samsung/phy-exynos4x12-usb2.c
new file mode 100644
index 000000000..7f27a91ac
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos4x12-usb2.c
@@ -0,0 +1,378 @@
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 4x12 support
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include "phy-samsung-usb2.h"
+
+/* Exynos USB PHY registers */
+
+/* PHY power control */
+#define EXYNOS_4x12_UPHYPWR			0x0
+
+#define EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND	BIT(0)
+#define EXYNOS_4x12_UPHYPWR_PHY0_PWR		BIT(3)
+#define EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR	BIT(4)
+#define EXYNOS_4x12_UPHYPWR_PHY0_SLEEP		BIT(5)
+#define EXYNOS_4x12_UPHYPWR_PHY0 ( \
+	EXYNOS_4x12_UPHYPWR_PHY0_SUSPEND | \
+	EXYNOS_4x12_UPHYPWR_PHY0_PWR | \
+	EXYNOS_4x12_UPHYPWR_PHY0_OTG_PWR | \
+	EXYNOS_4x12_UPHYPWR_PHY0_SLEEP)
+
+#define EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND	BIT(6)
+#define EXYNOS_4x12_UPHYPWR_PHY1_PWR		BIT(7)
+#define EXYNOS_4x12_UPHYPWR_PHY1_SLEEP		BIT(8)
+#define EXYNOS_4x12_UPHYPWR_PHY1 ( \
+	EXYNOS_4x12_UPHYPWR_PHY1_SUSPEND | \
+	EXYNOS_4x12_UPHYPWR_PHY1_PWR | \
+	EXYNOS_4x12_UPHYPWR_PHY1_SLEEP)
+
+#define EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND	BIT(9)
+#define EXYNOS_4x12_UPHYPWR_HSIC0_PWR		BIT(10)
+#define EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP		BIT(11)
+#define EXYNOS_4x12_UPHYPWR_HSIC0 ( \
+	EXYNOS_4x12_UPHYPWR_HSIC0_SUSPEND | \
+	EXYNOS_4x12_UPHYPWR_HSIC0_PWR | \
+	EXYNOS_4x12_UPHYPWR_HSIC0_SLEEP)
+
+#define EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND	BIT(12)
+#define EXYNOS_4x12_UPHYPWR_HSIC1_PWR		BIT(13)
+#define EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP		BIT(14)
+#define EXYNOS_4x12_UPHYPWR_HSIC1 ( \
+	EXYNOS_4x12_UPHYPWR_HSIC1_SUSPEND | \
+	EXYNOS_4x12_UPHYPWR_HSIC1_PWR | \
+	EXYNOS_4x12_UPHYPWR_HSIC1_SLEEP)
+
+/* PHY clock control */
+#define EXYNOS_4x12_UPHYCLK			0x4
+
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK	(0x7 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET	0
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6	(0x0 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ	(0x1 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ	(0x2 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2	(0x3 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ	(0x4 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ	(0x5 << 0)
+#define EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ	(0x7 << 0)
+
+#define EXYNOS_3250_UPHYCLK_REFCLKSEL		(0x2 << 8)
+
+#define EXYNOS_4x12_UPHYCLK_PHY0_ID_PULLUP	BIT(3)
+#define EXYNOS_4x12_UPHYCLK_PHY0_COMMON_ON	BIT(4)
+#define EXYNOS_4x12_UPHYCLK_PHY1_COMMON_ON	BIT(7)
+
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_MASK	(0x7f << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_OFFSET  10
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_12MHZ	(0x24 << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_15MHZ	(0x1c << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_16MHZ	(0x1a << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_19MHZ2	(0x15 << 10)
+#define EXYNOS_4x12_UPHYCLK_HSIC_REFCLK_20MHZ	(0x14 << 10)
+
+/* PHY reset control */
+#define EXYNOS_4x12_UPHYRST			0x8
+
+#define EXYNOS_4x12_URSTCON_PHY0		BIT(0)
+#define EXYNOS_4x12_URSTCON_OTG_HLINK		BIT(1)
+#define EXYNOS_4x12_URSTCON_OTG_PHYLINK		BIT(2)
+#define EXYNOS_4x12_URSTCON_HOST_PHY		BIT(3)
+/* The following bit defines are presented in the
+ * order taken from the Exynos4412 reference manual.
+ *
+ * During experiments with the hardware and debugging
+ * it was determined that the hardware behaves contrary
+ * to the manual.
+ *
+ * The following bit values were chaned accordingly to the
+ * results of real hardware experiments.
+ */
+#define EXYNOS_4x12_URSTCON_PHY1		BIT(4)
+#define EXYNOS_4x12_URSTCON_HSIC0		BIT(6)
+#define EXYNOS_4x12_URSTCON_HSIC1		BIT(5)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_ALL	BIT(7)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_P0	BIT(10)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_P1	BIT(9)
+#define EXYNOS_4x12_URSTCON_HOST_LINK_P2	BIT(8)
+
+/* Isolation, configured in the power management unit */
+#define EXYNOS_4x12_USB_ISOL_OFFSET		0x704
+#define EXYNOS_4x12_USB_ISOL_OTG		BIT(0)
+#define EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET	0x708
+#define EXYNOS_4x12_USB_ISOL_HSIC0		BIT(0)
+#define EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET	0x70c
+#define EXYNOS_4x12_USB_ISOL_HSIC1		BIT(0)
+
+/* Mode switching SUB Device <-> Host */
+#define EXYNOS_4x12_MODE_SWITCH_OFFSET		0x21c
+#define EXYNOS_4x12_MODE_SWITCH_MASK		1
+#define EXYNOS_4x12_MODE_SWITCH_DEVICE		0
+#define EXYNOS_4x12_MODE_SWITCH_HOST		1
+
+enum exynos4x12_phy_id {
+	EXYNOS4x12_DEVICE,
+	EXYNOS4x12_HOST,
+	EXYNOS4x12_HSIC0,
+	EXYNOS4x12_HSIC1,
+	EXYNOS4x12_NUM_PHYS,
+};
+
+/*
+ * exynos4x12_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static int exynos4x12_rate_to_clk(unsigned long rate, u32 *reg)
+{
+	/* EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK */
+
+	switch (rate) {
+	case 9600 * KHZ:
+		*reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_9MHZ6;
+		break;
+	case 10 * MHZ:
+		*reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_10MHZ;
+		break;
+	case 12 * MHZ:
+		*reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_12MHZ;
+		break;
+	case 19200 * KHZ:
+		*reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_19MHZ2;
+		break;
+	case 20 * MHZ:
+		*reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_20MHZ;
+		break;
+	case 24 * MHZ:
+		*reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_24MHZ;
+		break;
+	case 50 * MHZ:
+		*reg = EXYNOS_4x12_UPHYCLK_PHYFSEL_50MHZ;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void exynos4x12_isol(struct samsung_usb2_phy_instance *inst, bool on)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 offset;
+	u32 mask;
+
+	switch (inst->cfg->id) {
+	case EXYNOS4x12_DEVICE:
+	case EXYNOS4x12_HOST:
+		offset = EXYNOS_4x12_USB_ISOL_OFFSET;
+		mask = EXYNOS_4x12_USB_ISOL_OTG;
+		break;
+	case EXYNOS4x12_HSIC0:
+		offset = EXYNOS_4x12_USB_ISOL_HSIC0_OFFSET;
+		mask = EXYNOS_4x12_USB_ISOL_HSIC0;
+		break;
+	case EXYNOS4x12_HSIC1:
+		offset = EXYNOS_4x12_USB_ISOL_HSIC1_OFFSET;
+		mask = EXYNOS_4x12_USB_ISOL_HSIC1;
+		break;
+	default:
+		return;
+	}
+
+	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
+}
+
+static void exynos4x12_setup_clk(struct samsung_usb2_phy_instance *inst)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 clk;
+
+	clk = readl(drv->reg_phy + EXYNOS_4x12_UPHYCLK);
+	clk &= ~EXYNOS_4x12_UPHYCLK_PHYFSEL_MASK;
+
+	if (drv->cfg->has_refclk_sel)
+		clk = EXYNOS_3250_UPHYCLK_REFCLKSEL;
+
+	clk |= drv->ref_reg_val << EXYNOS_4x12_UPHYCLK_PHYFSEL_OFFSET;
+	clk |= EXYNOS_4x12_UPHYCLK_PHY1_COMMON_ON;
+	writel(clk, drv->reg_phy + EXYNOS_4x12_UPHYCLK);
+}
+
+static void exynos4x12_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 rstbits = 0;
+	u32 phypwr = 0;
+	u32 rst;
+	u32 pwr;
+
+	switch (inst->cfg->id) {
+	case EXYNOS4x12_DEVICE:
+		phypwr =	EXYNOS_4x12_UPHYPWR_PHY0;
+		rstbits =	EXYNOS_4x12_URSTCON_PHY0;
+		break;
+	case EXYNOS4x12_HOST:
+		phypwr =	EXYNOS_4x12_UPHYPWR_PHY1;
+		rstbits =	EXYNOS_4x12_URSTCON_HOST_PHY |
+				EXYNOS_4x12_URSTCON_PHY1 |
+				EXYNOS_4x12_URSTCON_HOST_LINK_P0;
+		break;
+	case EXYNOS4x12_HSIC0:
+		phypwr =	EXYNOS_4x12_UPHYPWR_HSIC0;
+		rstbits =	EXYNOS_4x12_URSTCON_HSIC0 |
+				EXYNOS_4x12_URSTCON_HOST_LINK_P1;
+		break;
+	case EXYNOS4x12_HSIC1:
+		phypwr =	EXYNOS_4x12_UPHYPWR_HSIC1;
+		rstbits =	EXYNOS_4x12_URSTCON_HSIC1 |
+				EXYNOS_4x12_URSTCON_HOST_LINK_P1;
+		break;
+	}
+
+	if (on) {
+		pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+		pwr &= ~phypwr;
+		writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+
+		rst = readl(drv->reg_phy + EXYNOS_4x12_UPHYRST);
+		rst |= rstbits;
+		writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST);
+		udelay(10);
+		rst &= ~rstbits;
+		writel(rst, drv->reg_phy + EXYNOS_4x12_UPHYRST);
+		/* The following delay is necessary for the reset sequence to be
+		 * completed */
+		udelay(80);
+	} else {
+		pwr = readl(drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+		pwr |= phypwr;
+		writel(pwr, drv->reg_phy + EXYNOS_4x12_UPHYPWR);
+	}
+}
+
+static void exynos4x12_power_on_int(struct samsung_usb2_phy_instance *inst)
+{
+	if (inst->int_cnt++ > 0)
+		return;
+
+	exynos4x12_setup_clk(inst);
+	exynos4x12_isol(inst, 0);
+	exynos4x12_phy_pwr(inst, 1);
+}
+
+static int exynos4x12_power_on(struct samsung_usb2_phy_instance *inst)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+
+	if (inst->ext_cnt++ > 0)
+		return 0;
+
+	if (inst->cfg->id == EXYNOS4x12_HOST) {
+		regmap_update_bits(drv->reg_sys, EXYNOS_4x12_MODE_SWITCH_OFFSET,
+						EXYNOS_4x12_MODE_SWITCH_MASK,
+						EXYNOS_4x12_MODE_SWITCH_HOST);
+		exynos4x12_power_on_int(&drv->instances[EXYNOS4x12_DEVICE]);
+	}
+
+	if (inst->cfg->id == EXYNOS4x12_DEVICE && drv->cfg->has_mode_switch)
+		regmap_update_bits(drv->reg_sys, EXYNOS_4x12_MODE_SWITCH_OFFSET,
+						EXYNOS_4x12_MODE_SWITCH_MASK,
+						EXYNOS_4x12_MODE_SWITCH_DEVICE);
+
+	if (inst->cfg->id == EXYNOS4x12_HSIC0 ||
+		inst->cfg->id == EXYNOS4x12_HSIC1) {
+		exynos4x12_power_on_int(&drv->instances[EXYNOS4x12_DEVICE]);
+		exynos4x12_power_on_int(&drv->instances[EXYNOS4x12_HOST]);
+	}
+
+	exynos4x12_power_on_int(inst);
+
+	return 0;
+}
+
+static void exynos4x12_power_off_int(struct samsung_usb2_phy_instance *inst)
+{
+	if (inst->int_cnt-- > 1)
+		return;
+
+	exynos4x12_isol(inst, 1);
+	exynos4x12_phy_pwr(inst, 0);
+}
+
+static int exynos4x12_power_off(struct samsung_usb2_phy_instance *inst)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+
+	if (inst->ext_cnt-- > 1)
+		return 0;
+
+	if (inst->cfg->id == EXYNOS4x12_DEVICE && drv->cfg->has_mode_switch)
+		regmap_update_bits(drv->reg_sys, EXYNOS_4x12_MODE_SWITCH_OFFSET,
+						EXYNOS_4x12_MODE_SWITCH_MASK,
+						EXYNOS_4x12_MODE_SWITCH_HOST);
+
+	if (inst->cfg->id == EXYNOS4x12_HOST)
+		exynos4x12_power_off_int(&drv->instances[EXYNOS4x12_DEVICE]);
+
+	if (inst->cfg->id == EXYNOS4x12_HSIC0 ||
+		inst->cfg->id == EXYNOS4x12_HSIC1) {
+		exynos4x12_power_off_int(&drv->instances[EXYNOS4x12_DEVICE]);
+		exynos4x12_power_off_int(&drv->instances[EXYNOS4x12_HOST]);
+	}
+
+	exynos4x12_power_off_int(inst);
+
+	return 0;
+}
+
+
+static const struct samsung_usb2_common_phy exynos4x12_phys[] = {
+	{
+		.label		= "device",
+		.id		= EXYNOS4x12_DEVICE,
+		.power_on	= exynos4x12_power_on,
+		.power_off	= exynos4x12_power_off,
+	},
+	{
+		.label		= "host",
+		.id		= EXYNOS4x12_HOST,
+		.power_on	= exynos4x12_power_on,
+		.power_off	= exynos4x12_power_off,
+	},
+	{
+		.label		= "hsic0",
+		.id		= EXYNOS4x12_HSIC0,
+		.power_on	= exynos4x12_power_on,
+		.power_off	= exynos4x12_power_off,
+	},
+	{
+		.label		= "hsic1",
+		.id		= EXYNOS4x12_HSIC1,
+		.power_on	= exynos4x12_power_on,
+		.power_off	= exynos4x12_power_off,
+	},
+};
+
+const struct samsung_usb2_phy_config exynos3250_usb2_phy_config = {
+	.has_refclk_sel		= 1,
+	.num_phys		= 1,
+	.phys			= exynos4x12_phys,
+	.rate_to_clk		= exynos4x12_rate_to_clk,
+};
+
+const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config = {
+	.has_mode_switch	= 1,
+	.num_phys		= EXYNOS4x12_NUM_PHYS,
+	.phys			= exynos4x12_phys,
+	.rate_to_clk		= exynos4x12_rate_to_clk,
+};
diff --git a/drivers/phy/samsung/phy-exynos5-usbdrd.c b/drivers/phy/samsung/phy-exynos5-usbdrd.c
new file mode 100644
index 000000000..1feb1e1bf
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos5-usbdrd.c
@@ -0,0 +1,968 @@
+/*
+ * Samsung EXYNOS5 SoC series USB DRD PHY driver
+ *
+ * Phy provider for USB 3.0 DRD controller on Exynos5 SoC series
+ *
+ * Copyright (C) 2014 Samsung Electronics Co., Ltd.
+ * Author: Vivek Gautam <gautam.vivek@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/mutex.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/soc/samsung/exynos-regs-pmu.h>
+
+/* Exynos USB PHY registers */
+#define EXYNOS5_FSEL_9MHZ6		0x0
+#define EXYNOS5_FSEL_10MHZ		0x1
+#define EXYNOS5_FSEL_12MHZ		0x2
+#define EXYNOS5_FSEL_19MHZ2		0x3
+#define EXYNOS5_FSEL_20MHZ		0x4
+#define EXYNOS5_FSEL_24MHZ		0x5
+#define EXYNOS5_FSEL_50MHZ		0x7
+
+/* EXYNOS5: USB 3.0 DRD PHY registers */
+#define EXYNOS5_DRD_LINKSYSTEM			0x04
+
+#define LINKSYSTEM_FLADJ_MASK			(0x3f << 1)
+#define LINKSYSTEM_FLADJ(_x)			((_x) << 1)
+#define LINKSYSTEM_XHCI_VERSION_CONTROL		BIT(27)
+
+#define EXYNOS5_DRD_PHYUTMI			0x08
+
+#define PHYUTMI_OTGDISABLE			BIT(6)
+#define PHYUTMI_FORCESUSPEND			BIT(1)
+#define PHYUTMI_FORCESLEEP			BIT(0)
+
+#define EXYNOS5_DRD_PHYPIPE			0x0c
+
+#define EXYNOS5_DRD_PHYCLKRST			0x10
+
+#define PHYCLKRST_EN_UTMISUSPEND		BIT(31)
+
+#define PHYCLKRST_SSC_REFCLKSEL_MASK		(0xff << 23)
+#define PHYCLKRST_SSC_REFCLKSEL(_x)		((_x) << 23)
+
+#define PHYCLKRST_SSC_RANGE_MASK		(0x03 << 21)
+#define PHYCLKRST_SSC_RANGE(_x)			((_x) << 21)
+
+#define PHYCLKRST_SSC_EN			BIT(20)
+#define PHYCLKRST_REF_SSP_EN			BIT(19)
+#define PHYCLKRST_REF_CLKDIV2			BIT(18)
+
+#define PHYCLKRST_MPLL_MULTIPLIER_MASK		(0x7f << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_100MHZ_REF	(0x19 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_50M_REF	(0x32 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF	(0x68 << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF	(0x7d << 11)
+#define PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF	(0x02 << 11)
+
+#define PHYCLKRST_FSEL_UTMI_MASK		(0x7 << 5)
+#define PHYCLKRST_FSEL_PIPE_MASK		(0x7 << 8)
+#define PHYCLKRST_FSEL(_x)			((_x) << 5)
+#define PHYCLKRST_FSEL_PAD_100MHZ		(0x27 << 5)
+#define PHYCLKRST_FSEL_PAD_24MHZ		(0x2a << 5)
+#define PHYCLKRST_FSEL_PAD_20MHZ		(0x31 << 5)
+#define PHYCLKRST_FSEL_PAD_19_2MHZ		(0x38 << 5)
+
+#define PHYCLKRST_RETENABLEN			BIT(4)
+
+#define PHYCLKRST_REFCLKSEL_MASK		(0x03 << 2)
+#define PHYCLKRST_REFCLKSEL_PAD_REFCLK		(0x2 << 2)
+#define PHYCLKRST_REFCLKSEL_EXT_REFCLK		(0x3 << 2)
+
+#define PHYCLKRST_PORTRESET			BIT(1)
+#define PHYCLKRST_COMMONONN			BIT(0)
+
+#define EXYNOS5_DRD_PHYREG0			0x14
+#define PHYREG0_SSC_REF_CLK_SEL			BIT(21)
+#define PHYREG0_SSC_RANGE			BIT(20)
+#define PHYREG0_CR_WRITE			BIT(19)
+#define PHYREG0_CR_READ				BIT(18)
+#define PHYREG0_CR_DATA_IN(_x)			((_x) << 2)
+#define PHYREG0_CR_CAP_DATA			BIT(1)
+#define PHYREG0_CR_CAP_ADDR			BIT(0)
+
+#define EXYNOS5_DRD_PHYREG1			0x18
+#define PHYREG1_CR_DATA_OUT(_x)			((_x) << 1)
+#define PHYREG1_CR_ACK				BIT(0)
+
+#define EXYNOS5_DRD_PHYPARAM0			0x1c
+
+#define PHYPARAM0_REF_USE_PAD			BIT(31)
+#define PHYPARAM0_REF_LOSLEVEL_MASK		(0x1f << 26)
+#define PHYPARAM0_REF_LOSLEVEL			(0x9 << 26)
+
+#define EXYNOS5_DRD_PHYPARAM1			0x20
+
+#define PHYPARAM1_PCS_TXDEEMPH_MASK		(0x1f << 0)
+#define PHYPARAM1_PCS_TXDEEMPH			(0x1c)
+
+#define EXYNOS5_DRD_PHYTERM			0x24
+
+#define EXYNOS5_DRD_PHYTEST			0x28
+
+#define PHYTEST_POWERDOWN_SSP			BIT(3)
+#define PHYTEST_POWERDOWN_HSP			BIT(2)
+
+#define EXYNOS5_DRD_PHYADP			0x2c
+
+#define EXYNOS5_DRD_PHYUTMICLKSEL		0x30
+
+#define PHYUTMICLKSEL_UTMI_CLKSEL		BIT(2)
+
+#define EXYNOS5_DRD_PHYRESUME			0x34
+#define EXYNOS5_DRD_LINKPORT			0x44
+
+/* USB 3.0 DRD PHY SS Function Control Reg; accessed by CR_PORT */
+#define EXYNOS5_DRD_PHYSS_LOSLEVEL_OVRD_IN		(0x15)
+#define LOSLEVEL_OVRD_IN_LOS_BIAS_5420			(0x5 << 13)
+#define LOSLEVEL_OVRD_IN_LOS_BIAS_DEFAULT		(0x0 << 13)
+#define LOSLEVEL_OVRD_IN_EN				(0x1 << 10)
+#define LOSLEVEL_OVRD_IN_LOS_LEVEL_DEFAULT		(0x9 << 0)
+
+#define EXYNOS5_DRD_PHYSS_TX_VBOOSTLEVEL_OVRD_IN	(0x12)
+#define TX_VBOOSTLEVEL_OVRD_IN_VBOOST_5420		(0x5 << 13)
+#define TX_VBOOSTLEVEL_OVRD_IN_VBOOST_DEFAULT		(0x4 << 13)
+
+#define EXYNOS5_DRD_PHYSS_LANE0_TX_DEBUG		(0x1010)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_19M2_20M		(0x4 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_24M		(0x8 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_25M_26M		(0x8 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_48M_50M_52M	(0x20 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_62M5		(0x20 << 4)
+#define LANE0_TX_DEBUG_RXDET_MEAS_TIME_96M_100M		(0x40 << 4)
+
+#define KHZ	1000
+#define MHZ	(KHZ * KHZ)
+
+enum exynos5_usbdrd_phy_id {
+	EXYNOS5_DRDPHY_UTMI,
+	EXYNOS5_DRDPHY_PIPE3,
+	EXYNOS5_DRDPHYS_NUM,
+};
+
+struct phy_usb_instance;
+struct exynos5_usbdrd_phy;
+
+struct exynos5_usbdrd_phy_config {
+	u32 id;
+	void (*phy_isol)(struct phy_usb_instance *inst, u32 on);
+	void (*phy_init)(struct exynos5_usbdrd_phy *phy_drd);
+	unsigned int (*set_refclk)(struct phy_usb_instance *inst);
+};
+
+struct exynos5_usbdrd_phy_drvdata {
+	const struct exynos5_usbdrd_phy_config *phy_cfg;
+	u32 pmu_offset_usbdrd0_phy;
+	u32 pmu_offset_usbdrd1_phy;
+	bool has_common_clk_gate;
+};
+
+/**
+ * struct exynos5_usbdrd_phy - driver data for USB 3.0 PHY
+ * @dev: pointer to device instance of this platform device
+ * @reg_phy: usb phy controller register memory base
+ * @clk: phy clock for register access
+ * @pipeclk: clock for pipe3 phy
+ * @utmiclk: clock for utmi+ phy
+ * @itpclk: clock for ITP generation
+ * @drv_data: pointer to SoC level driver data structure
+ * @phys[]: array for 'EXYNOS5_DRDPHYS_NUM' number of PHY
+ *	    instances each with its 'phy' and 'phy_cfg'.
+ * @extrefclk: frequency select settings when using 'separate
+ *	       reference clocks' for SS and HS operations
+ * @ref_clk: reference clock to PHY block from which PHY's
+ *	     operational clocks are derived
+ * vbus: VBUS regulator for phy
+ * vbus_boost: Boost regulator for VBUS present on few Exynos boards
+ */
+struct exynos5_usbdrd_phy {
+	struct device *dev;
+	void __iomem *reg_phy;
+	struct clk *clk;
+	struct clk *pipeclk;
+	struct clk *utmiclk;
+	struct clk *itpclk;
+	const struct exynos5_usbdrd_phy_drvdata *drv_data;
+	struct phy_usb_instance {
+		struct phy *phy;
+		u32 index;
+		struct regmap *reg_pmu;
+		u32 pmu_offset;
+		const struct exynos5_usbdrd_phy_config *phy_cfg;
+	} phys[EXYNOS5_DRDPHYS_NUM];
+	u32 extrefclk;
+	struct clk *ref_clk;
+	struct regulator *vbus;
+	struct regulator *vbus_boost;
+};
+
+static inline
+struct exynos5_usbdrd_phy *to_usbdrd_phy(struct phy_usb_instance *inst)
+{
+	return container_of((inst), struct exynos5_usbdrd_phy,
+			    phys[(inst)->index]);
+}
+
+/*
+ * exynos5_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static unsigned int exynos5_rate_to_clk(unsigned long rate, u32 *reg)
+{
+	/* EXYNOS5_FSEL_MASK */
+
+	switch (rate) {
+	case 9600 * KHZ:
+		*reg = EXYNOS5_FSEL_9MHZ6;
+		break;
+	case 10 * MHZ:
+		*reg = EXYNOS5_FSEL_10MHZ;
+		break;
+	case 12 * MHZ:
+		*reg = EXYNOS5_FSEL_12MHZ;
+		break;
+	case 19200 * KHZ:
+		*reg = EXYNOS5_FSEL_19MHZ2;
+		break;
+	case 20 * MHZ:
+		*reg = EXYNOS5_FSEL_20MHZ;
+		break;
+	case 24 * MHZ:
+		*reg = EXYNOS5_FSEL_24MHZ;
+		break;
+	case 50 * MHZ:
+		*reg = EXYNOS5_FSEL_50MHZ;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void exynos5_usbdrd_phy_isol(struct phy_usb_instance *inst,
+						unsigned int on)
+{
+	unsigned int val;
+
+	if (!inst->reg_pmu)
+		return;
+
+	val = on ? 0 : EXYNOS4_PHY_ENABLE;
+
+	regmap_update_bits(inst->reg_pmu, inst->pmu_offset,
+			   EXYNOS4_PHY_ENABLE, val);
+}
+
+/*
+ * Sets the pipe3 phy's clk as EXTREFCLK (XXTI) which is internal clock
+ * from clock core. Further sets multiplier values and spread spectrum
+ * clock settings for SuperSpeed operations.
+ */
+static unsigned int
+exynos5_usbdrd_pipe3_set_refclk(struct phy_usb_instance *inst)
+{
+	u32 reg;
+	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+	/* restore any previous reference clock settings */
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+	/* Use EXTREFCLK as ref clock */
+	reg &= ~PHYCLKRST_REFCLKSEL_MASK;
+	reg |=	PHYCLKRST_REFCLKSEL_EXT_REFCLK;
+
+	/* FSEL settings corresponding to reference clock */
+	reg &= ~PHYCLKRST_FSEL_PIPE_MASK |
+		PHYCLKRST_MPLL_MULTIPLIER_MASK |
+		PHYCLKRST_SSC_REFCLKSEL_MASK;
+	switch (phy_drd->extrefclk) {
+	case EXYNOS5_FSEL_50MHZ:
+		reg |= (PHYCLKRST_MPLL_MULTIPLIER_50M_REF |
+			PHYCLKRST_SSC_REFCLKSEL(0x00));
+		break;
+	case EXYNOS5_FSEL_24MHZ:
+		reg |= (PHYCLKRST_MPLL_MULTIPLIER_24MHZ_REF |
+			PHYCLKRST_SSC_REFCLKSEL(0x88));
+		break;
+	case EXYNOS5_FSEL_20MHZ:
+		reg |= (PHYCLKRST_MPLL_MULTIPLIER_20MHZ_REF |
+			PHYCLKRST_SSC_REFCLKSEL(0x00));
+		break;
+	case EXYNOS5_FSEL_19MHZ2:
+		reg |= (PHYCLKRST_MPLL_MULTIPLIER_19200KHZ_REF |
+			PHYCLKRST_SSC_REFCLKSEL(0x88));
+		break;
+	default:
+		dev_dbg(phy_drd->dev, "unsupported ref clk\n");
+		break;
+	}
+
+	return reg;
+}
+
+/*
+ * Sets the utmi phy's clk as EXTREFCLK (XXTI) which is internal clock
+ * from clock core. Further sets the FSEL values for HighSpeed operations.
+ */
+static unsigned int
+exynos5_usbdrd_utmi_set_refclk(struct phy_usb_instance *inst)
+{
+	u32 reg;
+	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+	/* restore any previous reference clock settings */
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+	reg &= ~PHYCLKRST_REFCLKSEL_MASK;
+	reg |=	PHYCLKRST_REFCLKSEL_EXT_REFCLK;
+
+	reg &= ~PHYCLKRST_FSEL_UTMI_MASK |
+		PHYCLKRST_MPLL_MULTIPLIER_MASK |
+		PHYCLKRST_SSC_REFCLKSEL_MASK;
+	reg |= PHYCLKRST_FSEL(phy_drd->extrefclk);
+
+	return reg;
+}
+
+static void exynos5_usbdrd_pipe3_init(struct exynos5_usbdrd_phy *phy_drd)
+{
+	u32 reg;
+
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+	/* Set Tx De-Emphasis level */
+	reg &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
+	reg |=	PHYPARAM1_PCS_TXDEEMPH;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+	reg &= ~PHYTEST_POWERDOWN_SSP;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+}
+
+static void exynos5_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
+{
+	u32 reg;
+
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+	/* Set Loss-of-Signal Detector sensitivity */
+	reg &= ~PHYPARAM0_REF_LOSLEVEL_MASK;
+	reg |=	PHYPARAM0_REF_LOSLEVEL;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+	/* Set Tx De-Emphasis level */
+	reg &= ~PHYPARAM1_PCS_TXDEEMPH_MASK;
+	reg |=	PHYPARAM1_PCS_TXDEEMPH;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM1);
+
+	/* UTMI Power Control */
+	writel(PHYUTMI_OTGDISABLE, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+	reg &= ~PHYTEST_POWERDOWN_HSP;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+}
+
+static int exynos5_usbdrd_phy_init(struct phy *phy)
+{
+	int ret;
+	u32 reg;
+	struct phy_usb_instance *inst = phy_get_drvdata(phy);
+	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+	ret = clk_prepare_enable(phy_drd->clk);
+	if (ret)
+		return ret;
+
+	/* Reset USB 3.0 PHY */
+	writel(0x0, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+	writel(0x0, phy_drd->reg_phy + EXYNOS5_DRD_PHYRESUME);
+
+	/*
+	 * Setting the Frame length Adj value[6:1] to default 0x20
+	 * See xHCI 1.0 spec, 5.2.4
+	 */
+	reg =	LINKSYSTEM_XHCI_VERSION_CONTROL |
+		LINKSYSTEM_FLADJ(0x20);
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_LINKSYSTEM);
+
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+	/* Select PHY CLK source */
+	reg &= ~PHYPARAM0_REF_USE_PAD;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYPARAM0);
+
+	/* This bit must be set for both HS and SS operations */
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMICLKSEL);
+	reg |= PHYUTMICLKSEL_UTMI_CLKSEL;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMICLKSEL);
+
+	/* UTMI or PIPE3 specific init */
+	inst->phy_cfg->phy_init(phy_drd);
+
+	/* reference clock settings */
+	reg = inst->phy_cfg->set_refclk(inst);
+
+		/* Digital power supply in normal operating mode */
+	reg |=	PHYCLKRST_RETENABLEN |
+		/* Enable ref clock for SS function */
+		PHYCLKRST_REF_SSP_EN |
+		/* Enable spread spectrum */
+		PHYCLKRST_SSC_EN |
+		/* Power down HS Bias and PLL blocks in suspend mode */
+		PHYCLKRST_COMMONONN |
+		/* Reset the port */
+		PHYCLKRST_PORTRESET;
+
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+	udelay(10);
+
+	reg &= ~PHYCLKRST_PORTRESET;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+	clk_disable_unprepare(phy_drd->clk);
+
+	return 0;
+}
+
+static int exynos5_usbdrd_phy_exit(struct phy *phy)
+{
+	int ret;
+	u32 reg;
+	struct phy_usb_instance *inst = phy_get_drvdata(phy);
+	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+	ret = clk_prepare_enable(phy_drd->clk);
+	if (ret)
+		return ret;
+
+	reg =	PHYUTMI_OTGDISABLE |
+		PHYUTMI_FORCESUSPEND |
+		PHYUTMI_FORCESLEEP;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYUTMI);
+
+	/* Resetting the PHYCLKRST enable bits to reduce leakage current */
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+	reg &= ~(PHYCLKRST_REF_SSP_EN |
+		 PHYCLKRST_SSC_EN |
+		 PHYCLKRST_COMMONONN);
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYCLKRST);
+
+	/* Control PHYTEST to remove leakage current */
+	reg = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+	reg |=	PHYTEST_POWERDOWN_SSP |
+		PHYTEST_POWERDOWN_HSP;
+	writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
+
+	clk_disable_unprepare(phy_drd->clk);
+
+	return 0;
+}
+
+static int exynos5_usbdrd_phy_power_on(struct phy *phy)
+{
+	int ret;
+	struct phy_usb_instance *inst = phy_get_drvdata(phy);
+	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+	dev_dbg(phy_drd->dev, "Request to power_on usbdrd_phy phy\n");
+
+	clk_prepare_enable(phy_drd->ref_clk);
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		clk_prepare_enable(phy_drd->pipeclk);
+		clk_prepare_enable(phy_drd->utmiclk);
+		clk_prepare_enable(phy_drd->itpclk);
+	}
+
+	/* Enable VBUS supply */
+	if (phy_drd->vbus_boost) {
+		ret = regulator_enable(phy_drd->vbus_boost);
+		if (ret) {
+			dev_err(phy_drd->dev,
+				"Failed to enable VBUS boost supply\n");
+			goto fail_vbus;
+		}
+	}
+
+	if (phy_drd->vbus) {
+		ret = regulator_enable(phy_drd->vbus);
+		if (ret) {
+			dev_err(phy_drd->dev, "Failed to enable VBUS supply\n");
+			goto fail_vbus_boost;
+		}
+	}
+
+	/* Power-on PHY*/
+	inst->phy_cfg->phy_isol(inst, 0);
+
+	return 0;
+
+fail_vbus_boost:
+	if (phy_drd->vbus_boost)
+		regulator_disable(phy_drd->vbus_boost);
+
+fail_vbus:
+	clk_disable_unprepare(phy_drd->ref_clk);
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		clk_disable_unprepare(phy_drd->itpclk);
+		clk_disable_unprepare(phy_drd->utmiclk);
+		clk_disable_unprepare(phy_drd->pipeclk);
+	}
+
+	return ret;
+}
+
+static int exynos5_usbdrd_phy_power_off(struct phy *phy)
+{
+	struct phy_usb_instance *inst = phy_get_drvdata(phy);
+	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+	dev_dbg(phy_drd->dev, "Request to power_off usbdrd_phy phy\n");
+
+	/* Power-off the PHY */
+	inst->phy_cfg->phy_isol(inst, 1);
+
+	/* Disable VBUS supply */
+	if (phy_drd->vbus)
+		regulator_disable(phy_drd->vbus);
+	if (phy_drd->vbus_boost)
+		regulator_disable(phy_drd->vbus_boost);
+
+	clk_disable_unprepare(phy_drd->ref_clk);
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		clk_disable_unprepare(phy_drd->itpclk);
+		clk_disable_unprepare(phy_drd->pipeclk);
+		clk_disable_unprepare(phy_drd->utmiclk);
+	}
+
+	return 0;
+}
+
+static int crport_handshake(struct exynos5_usbdrd_phy *phy_drd,
+			    u32 val, u32 cmd)
+{
+	u32 usec = 100;
+	unsigned int result;
+
+	writel(val | cmd, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+
+	do {
+		result = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYREG1);
+		if (result & PHYREG1_CR_ACK)
+			break;
+
+		udelay(1);
+	} while (usec-- > 0);
+
+	if (!usec) {
+		dev_err(phy_drd->dev,
+			"CRPORT handshake timeout1 (0x%08x)\n", val);
+		return -ETIME;
+	}
+
+	usec = 100;
+
+	writel(val, phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+
+	do {
+		result = readl(phy_drd->reg_phy + EXYNOS5_DRD_PHYREG1);
+		if (!(result & PHYREG1_CR_ACK))
+			break;
+
+		udelay(1);
+	} while (usec-- > 0);
+
+	if (!usec) {
+		dev_err(phy_drd->dev,
+			"CRPORT handshake timeout2 (0x%08x)\n", val);
+		return -ETIME;
+	}
+
+	return 0;
+}
+
+static int crport_ctrl_write(struct exynos5_usbdrd_phy *phy_drd,
+			     u32 addr, u32 data)
+{
+	int ret;
+
+	/* Write Address */
+	writel(PHYREG0_CR_DATA_IN(addr),
+	       phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+	ret = crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(addr),
+			       PHYREG0_CR_CAP_ADDR);
+	if (ret)
+		return ret;
+
+	/* Write Data */
+	writel(PHYREG0_CR_DATA_IN(data),
+	       phy_drd->reg_phy + EXYNOS5_DRD_PHYREG0);
+	ret = crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(data),
+			       PHYREG0_CR_CAP_DATA);
+	if (ret)
+		return ret;
+
+	ret = crport_handshake(phy_drd, PHYREG0_CR_DATA_IN(data),
+			       PHYREG0_CR_WRITE);
+
+	return ret;
+}
+
+/*
+ * Calibrate few PHY parameters using CR_PORT register to meet
+ * SuperSpeed requirements on Exynos5420 and Exynos5800 systems,
+ * which have 28nm USB 3.0 DRD PHY.
+ */
+static int exynos5420_usbdrd_phy_calibrate(struct exynos5_usbdrd_phy *phy_drd)
+{
+	unsigned int temp;
+	int ret = 0;
+
+	/*
+	 * Change los_bias to (0x5) for 28nm PHY from a
+	 * default value (0x0); los_level is set as default
+	 * (0x9) as also reflected in los_level[30:26] bits
+	 * of PHYPARAM0 register.
+	 */
+	temp = LOSLEVEL_OVRD_IN_LOS_BIAS_5420 |
+		LOSLEVEL_OVRD_IN_EN |
+		LOSLEVEL_OVRD_IN_LOS_LEVEL_DEFAULT;
+	ret = crport_ctrl_write(phy_drd,
+				EXYNOS5_DRD_PHYSS_LOSLEVEL_OVRD_IN,
+				temp);
+	if (ret) {
+		dev_err(phy_drd->dev,
+			"Failed setting Loss-of-Signal level for SuperSpeed\n");
+		return ret;
+	}
+
+	/*
+	 * Set tx_vboost_lvl to (0x5) for 28nm PHY Tuning,
+	 * to raise Tx signal level from its default value of (0x4)
+	 */
+	temp = TX_VBOOSTLEVEL_OVRD_IN_VBOOST_5420;
+	ret = crport_ctrl_write(phy_drd,
+				EXYNOS5_DRD_PHYSS_TX_VBOOSTLEVEL_OVRD_IN,
+				temp);
+	if (ret) {
+		dev_err(phy_drd->dev,
+			"Failed setting Tx-Vboost-Level for SuperSpeed\n");
+		return ret;
+	}
+
+	/*
+	 * Set proper time to wait for RxDetect measurement, for
+	 * desired reference clock of PHY, by tuning the CR_PORT
+	 * register LANE0.TX_DEBUG which is internal to PHY.
+	 * This fixes issue with few USB 3.0 devices, which are
+	 * not detected (not even generate interrupts on the bus
+	 * on insertion) without this change.
+	 * e.g. Samsung SUM-TSB16S 3.0 USB drive.
+	 */
+	switch (phy_drd->extrefclk) {
+	case EXYNOS5_FSEL_50MHZ:
+		temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_48M_50M_52M;
+		break;
+	case EXYNOS5_FSEL_20MHZ:
+	case EXYNOS5_FSEL_19MHZ2:
+		temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_19M2_20M;
+		break;
+	case EXYNOS5_FSEL_24MHZ:
+	default:
+		temp = LANE0_TX_DEBUG_RXDET_MEAS_TIME_24M;
+		break;
+	}
+
+	ret = crport_ctrl_write(phy_drd,
+				EXYNOS5_DRD_PHYSS_LANE0_TX_DEBUG,
+				temp);
+	if (ret)
+		dev_err(phy_drd->dev,
+			"Fail to set RxDet measurement time for SuperSpeed\n");
+
+	return ret;
+}
+
+static struct phy *exynos5_usbdrd_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct exynos5_usbdrd_phy *phy_drd = dev_get_drvdata(dev);
+
+	if (WARN_ON(args->args[0] >= EXYNOS5_DRDPHYS_NUM))
+		return ERR_PTR(-ENODEV);
+
+	return phy_drd->phys[args->args[0]].phy;
+}
+
+static int exynos5_usbdrd_phy_calibrate(struct phy *phy)
+{
+	struct phy_usb_instance *inst = phy_get_drvdata(phy);
+	struct exynos5_usbdrd_phy *phy_drd = to_usbdrd_phy(inst);
+
+	if (inst->phy_cfg->id == EXYNOS5_DRDPHY_UTMI)
+		return exynos5420_usbdrd_phy_calibrate(phy_drd);
+	return 0;
+}
+
+static const struct phy_ops exynos5_usbdrd_phy_ops = {
+	.init		= exynos5_usbdrd_phy_init,
+	.exit		= exynos5_usbdrd_phy_exit,
+	.power_on	= exynos5_usbdrd_phy_power_on,
+	.power_off	= exynos5_usbdrd_phy_power_off,
+	.calibrate	= exynos5_usbdrd_phy_calibrate,
+	.owner		= THIS_MODULE,
+};
+
+static int exynos5_usbdrd_phy_clk_handle(struct exynos5_usbdrd_phy *phy_drd)
+{
+	unsigned long ref_rate;
+	int ret;
+
+	phy_drd->clk = devm_clk_get(phy_drd->dev, "phy");
+	if (IS_ERR(phy_drd->clk)) {
+		dev_err(phy_drd->dev, "Failed to get phy clock\n");
+		return PTR_ERR(phy_drd->clk);
+	}
+
+	phy_drd->ref_clk = devm_clk_get(phy_drd->dev, "ref");
+	if (IS_ERR(phy_drd->ref_clk)) {
+		dev_err(phy_drd->dev, "Failed to get phy reference clock\n");
+		return PTR_ERR(phy_drd->ref_clk);
+	}
+	ref_rate = clk_get_rate(phy_drd->ref_clk);
+
+	ret = exynos5_rate_to_clk(ref_rate, &phy_drd->extrefclk);
+	if (ret) {
+		dev_err(phy_drd->dev, "Clock rate (%ld) not supported\n",
+			ref_rate);
+		return ret;
+	}
+
+	if (!phy_drd->drv_data->has_common_clk_gate) {
+		phy_drd->pipeclk = devm_clk_get(phy_drd->dev, "phy_pipe");
+		if (IS_ERR(phy_drd->pipeclk)) {
+			dev_info(phy_drd->dev,
+				 "PIPE3 phy operational clock not specified\n");
+			phy_drd->pipeclk = NULL;
+		}
+
+		phy_drd->utmiclk = devm_clk_get(phy_drd->dev, "phy_utmi");
+		if (IS_ERR(phy_drd->utmiclk)) {
+			dev_info(phy_drd->dev,
+				 "UTMI phy operational clock not specified\n");
+			phy_drd->utmiclk = NULL;
+		}
+
+		phy_drd->itpclk = devm_clk_get(phy_drd->dev, "itp");
+		if (IS_ERR(phy_drd->itpclk)) {
+			dev_info(phy_drd->dev,
+				 "ITP clock from main OSC not specified\n");
+			phy_drd->itpclk = NULL;
+		}
+	}
+
+	return 0;
+}
+
+static const struct exynos5_usbdrd_phy_config phy_cfg_exynos5[] = {
+	{
+		.id		= EXYNOS5_DRDPHY_UTMI,
+		.phy_isol	= exynos5_usbdrd_phy_isol,
+		.phy_init	= exynos5_usbdrd_utmi_init,
+		.set_refclk	= exynos5_usbdrd_utmi_set_refclk,
+	},
+	{
+		.id		= EXYNOS5_DRDPHY_PIPE3,
+		.phy_isol	= exynos5_usbdrd_phy_isol,
+		.phy_init	= exynos5_usbdrd_pipe3_init,
+		.set_refclk	= exynos5_usbdrd_pipe3_set_refclk,
+	},
+};
+
+static const struct exynos5_usbdrd_phy_drvdata exynos5420_usbdrd_phy = {
+	.phy_cfg		= phy_cfg_exynos5,
+	.pmu_offset_usbdrd0_phy	= EXYNOS5_USBDRD_PHY_CONTROL,
+	.pmu_offset_usbdrd1_phy	= EXYNOS5420_USBDRD1_PHY_CONTROL,
+	.has_common_clk_gate	= true,
+};
+
+static const struct exynos5_usbdrd_phy_drvdata exynos5250_usbdrd_phy = {
+	.phy_cfg		= phy_cfg_exynos5,
+	.pmu_offset_usbdrd0_phy	= EXYNOS5_USBDRD_PHY_CONTROL,
+	.has_common_clk_gate	= true,
+};
+
+static const struct exynos5_usbdrd_phy_drvdata exynos5433_usbdrd_phy = {
+	.phy_cfg		= phy_cfg_exynos5,
+	.pmu_offset_usbdrd0_phy	= EXYNOS5_USBDRD_PHY_CONTROL,
+	.pmu_offset_usbdrd1_phy	= EXYNOS5433_USBHOST30_PHY_CONTROL,
+	.has_common_clk_gate	= false,
+};
+
+static const struct exynos5_usbdrd_phy_drvdata exynos7_usbdrd_phy = {
+	.phy_cfg		= phy_cfg_exynos5,
+	.pmu_offset_usbdrd0_phy	= EXYNOS5_USBDRD_PHY_CONTROL,
+	.has_common_clk_gate	= false,
+};
+
+static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
+	{
+		.compatible = "samsung,exynos5250-usbdrd-phy",
+		.data = &exynos5250_usbdrd_phy
+	}, {
+		.compatible = "samsung,exynos5420-usbdrd-phy",
+		.data = &exynos5420_usbdrd_phy
+	}, {
+		.compatible = "samsung,exynos5433-usbdrd-phy",
+		.data = &exynos5433_usbdrd_phy
+	}, {
+		.compatible = "samsung,exynos7-usbdrd-phy",
+		.data = &exynos7_usbdrd_phy
+	},
+	{ },
+};
+MODULE_DEVICE_TABLE(of, exynos5_usbdrd_phy_of_match);
+
+static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *node = dev->of_node;
+	struct exynos5_usbdrd_phy *phy_drd;
+	struct phy_provider *phy_provider;
+	struct resource *res;
+	const struct exynos5_usbdrd_phy_drvdata *drv_data;
+	struct regmap *reg_pmu;
+	u32 pmu_offset;
+	int i, ret;
+	int channel;
+
+	phy_drd = devm_kzalloc(dev, sizeof(*phy_drd), GFP_KERNEL);
+	if (!phy_drd)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, phy_drd);
+	phy_drd->dev = dev;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	phy_drd->reg_phy = devm_ioremap_resource(dev, res);
+	if (IS_ERR(phy_drd->reg_phy))
+		return PTR_ERR(phy_drd->reg_phy);
+
+	drv_data = of_device_get_match_data(dev);
+	if (!drv_data)
+		return -EINVAL;
+
+	phy_drd->drv_data = drv_data;
+
+	ret = exynos5_usbdrd_phy_clk_handle(phy_drd);
+	if (ret) {
+		dev_err(dev, "Failed to initialize clocks\n");
+		return ret;
+	}
+
+	reg_pmu = syscon_regmap_lookup_by_phandle(dev->of_node,
+						   "samsung,pmu-syscon");
+	if (IS_ERR(reg_pmu)) {
+		dev_err(dev, "Failed to lookup PMU regmap\n");
+		return PTR_ERR(reg_pmu);
+	}
+
+	/*
+	 * Exynos5420 SoC has multiple channels for USB 3.0 PHY, with
+	 * each having separate power control registers.
+	 * 'channel' facilitates to set such registers.
+	 */
+	channel = of_alias_get_id(node, "usbdrdphy");
+	if (channel < 0)
+		dev_dbg(dev, "Not a multi-controller usbdrd phy\n");
+
+	switch (channel) {
+	case 1:
+		pmu_offset = phy_drd->drv_data->pmu_offset_usbdrd1_phy;
+		break;
+	case 0:
+	default:
+		pmu_offset = phy_drd->drv_data->pmu_offset_usbdrd0_phy;
+		break;
+	}
+
+	/* Get Vbus regulators */
+	phy_drd->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(phy_drd->vbus)) {
+		ret = PTR_ERR(phy_drd->vbus);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
+		dev_warn(dev, "Failed to get VBUS supply regulator\n");
+		phy_drd->vbus = NULL;
+	}
+
+	phy_drd->vbus_boost = devm_regulator_get(dev, "vbus-boost");
+	if (IS_ERR(phy_drd->vbus_boost)) {
+		ret = PTR_ERR(phy_drd->vbus_boost);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+
+		dev_warn(dev, "Failed to get VBUS boost supply regulator\n");
+		phy_drd->vbus_boost = NULL;
+	}
+
+	dev_vdbg(dev, "Creating usbdrd_phy phy\n");
+
+	for (i = 0; i < EXYNOS5_DRDPHYS_NUM; i++) {
+		struct phy *phy = devm_phy_create(dev, NULL,
+						  &exynos5_usbdrd_phy_ops);
+		if (IS_ERR(phy)) {
+			dev_err(dev, "Failed to create usbdrd_phy phy\n");
+			return PTR_ERR(phy);
+		}
+
+		phy_drd->phys[i].phy = phy;
+		phy_drd->phys[i].index = i;
+		phy_drd->phys[i].reg_pmu = reg_pmu;
+		phy_drd->phys[i].pmu_offset = pmu_offset;
+		phy_drd->phys[i].phy_cfg = &drv_data->phy_cfg[i];
+		phy_set_drvdata(phy, &phy_drd->phys[i]);
+	}
+
+	phy_provider = devm_of_phy_provider_register(dev,
+						     exynos5_usbdrd_phy_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(phy_drd->dev, "Failed to register phy provider\n");
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static struct platform_driver exynos5_usb3drd_phy = {
+	.probe	= exynos5_usbdrd_phy_probe,
+	.driver = {
+		.of_match_table	= exynos5_usbdrd_phy_of_match,
+		.name		= "exynos5_usb3drd_phy",
+	}
+};
+
+module_platform_driver(exynos5_usb3drd_phy);
+MODULE_DESCRIPTION("Samsung EXYNOS5 SoCs USB 3.0 DRD controller PHY driver");
+MODULE_AUTHOR("Vivek Gautam <gautam.vivek@samsung.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:exynos5_usb3drd_phy");
diff --git a/drivers/phy/samsung/phy-exynos5250-sata.c b/drivers/phy/samsung/phy-exynos5250-sata.c
new file mode 100644
index 000000000..2c39d2fd3
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos5250-sata.c
@@ -0,0 +1,259 @@
+/*
+ * Samsung SATA SerDes(PHY) driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Authors: Girish K S <ks.giri@samsung.com>
+ *         Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/spinlock.h>
+#include <linux/mfd/syscon.h>
+
+#define SATAPHY_CONTROL_OFFSET		0x0724
+#define EXYNOS5_SATAPHY_PMU_ENABLE	BIT(0)
+#define EXYNOS5_SATA_RESET		0x4
+#define RESET_GLOBAL_RST_N		BIT(0)
+#define RESET_CMN_RST_N			BIT(1)
+#define RESET_CMN_BLOCK_RST_N		BIT(2)
+#define RESET_CMN_I2C_RST_N		BIT(3)
+#define RESET_TX_RX_PIPE_RST_N		BIT(4)
+#define RESET_TX_RX_BLOCK_RST_N		BIT(5)
+#define RESET_TX_RX_I2C_RST_N		(BIT(6) | BIT(7))
+#define LINK_RESET			0xf0000
+#define EXYNOS5_SATA_MODE0		0x10
+#define SATA_SPD_GEN3			BIT(1)
+#define EXYNOS5_SATA_CTRL0		0x14
+#define CTRL0_P0_PHY_CALIBRATED_SEL	BIT(9)
+#define CTRL0_P0_PHY_CALIBRATED		BIT(8)
+#define EXYNOS5_SATA_PHSATA_CTRLM	0xe0
+#define PHCTRLM_REF_RATE		BIT(1)
+#define PHCTRLM_HIGH_SPEED		BIT(0)
+#define EXYNOS5_SATA_PHSATA_STATM	0xf0
+#define PHSTATM_PLL_LOCKED		BIT(0)
+
+#define PHY_PLL_TIMEOUT (usecs_to_jiffies(1000))
+
+struct exynos_sata_phy {
+	struct phy *phy;
+	struct clk *phyclk;
+	void __iomem *regs;
+	struct regmap *pmureg;
+	struct i2c_client *client;
+};
+
+static int wait_for_reg_status(void __iomem *base, u32 reg, u32 checkbit,
+				u32 status)
+{
+	unsigned long timeout = jiffies + PHY_PLL_TIMEOUT;
+
+	while (time_before(jiffies, timeout)) {
+		if ((readl(base + reg) & checkbit) == status)
+			return 0;
+	}
+
+	return -EFAULT;
+}
+
+static int exynos_sata_phy_power_on(struct phy *phy)
+{
+	struct exynos_sata_phy *sata_phy = phy_get_drvdata(phy);
+
+	return regmap_update_bits(sata_phy->pmureg, SATAPHY_CONTROL_OFFSET,
+			EXYNOS5_SATAPHY_PMU_ENABLE, true);
+
+}
+
+static int exynos_sata_phy_power_off(struct phy *phy)
+{
+	struct exynos_sata_phy *sata_phy = phy_get_drvdata(phy);
+
+	return regmap_update_bits(sata_phy->pmureg, SATAPHY_CONTROL_OFFSET,
+			EXYNOS5_SATAPHY_PMU_ENABLE, false);
+
+}
+
+static int exynos_sata_phy_init(struct phy *phy)
+{
+	u32 val = 0;
+	int ret = 0;
+	u8 buf[] = { 0x3a, 0x0b };
+	struct exynos_sata_phy *sata_phy = phy_get_drvdata(phy);
+
+	ret = regmap_update_bits(sata_phy->pmureg, SATAPHY_CONTROL_OFFSET,
+			EXYNOS5_SATAPHY_PMU_ENABLE, true);
+	if (ret != 0)
+		dev_err(&sata_phy->phy->dev, "phy init failed\n");
+
+	writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
+
+	val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
+	val |= RESET_GLOBAL_RST_N | RESET_CMN_RST_N | RESET_CMN_BLOCK_RST_N
+		| RESET_CMN_I2C_RST_N | RESET_TX_RX_PIPE_RST_N
+		| RESET_TX_RX_BLOCK_RST_N | RESET_TX_RX_I2C_RST_N;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
+
+	val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
+	val |= LINK_RESET;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
+
+	val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
+	val |= RESET_CMN_RST_N;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
+
+	val = readl(sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
+	val &= ~PHCTRLM_REF_RATE;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
+
+	/* High speed enable for Gen3 */
+	val = readl(sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
+	val |= PHCTRLM_HIGH_SPEED;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_PHSATA_CTRLM);
+
+	val = readl(sata_phy->regs + EXYNOS5_SATA_CTRL0);
+	val |= CTRL0_P0_PHY_CALIBRATED_SEL | CTRL0_P0_PHY_CALIBRATED;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_CTRL0);
+
+	val = readl(sata_phy->regs + EXYNOS5_SATA_MODE0);
+	val |= SATA_SPD_GEN3;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_MODE0);
+
+	ret = i2c_master_send(sata_phy->client, buf, sizeof(buf));
+	if (ret < 0)
+		return ret;
+
+	/* release cmu reset */
+	val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
+	val &= ~RESET_CMN_RST_N;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
+
+	val = readl(sata_phy->regs + EXYNOS5_SATA_RESET);
+	val |= RESET_CMN_RST_N;
+	writel(val, sata_phy->regs + EXYNOS5_SATA_RESET);
+
+	ret = wait_for_reg_status(sata_phy->regs,
+				EXYNOS5_SATA_PHSATA_STATM,
+				PHSTATM_PLL_LOCKED, 1);
+	if (ret < 0)
+		dev_err(&sata_phy->phy->dev,
+			"PHY PLL locking failed\n");
+	return ret;
+}
+
+static const struct phy_ops exynos_sata_phy_ops = {
+	.init		= exynos_sata_phy_init,
+	.power_on	= exynos_sata_phy_power_on,
+	.power_off	= exynos_sata_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static int exynos_sata_phy_probe(struct platform_device *pdev)
+{
+	struct exynos_sata_phy *sata_phy;
+	struct device *dev = &pdev->dev;
+	struct resource *res;
+	struct phy_provider *phy_provider;
+	struct device_node *node;
+	int ret = 0;
+
+	sata_phy = devm_kzalloc(dev, sizeof(*sata_phy), GFP_KERNEL);
+	if (!sata_phy)
+		return -ENOMEM;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+
+	sata_phy->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(sata_phy->regs))
+		return PTR_ERR(sata_phy->regs);
+
+	sata_phy->pmureg = syscon_regmap_lookup_by_phandle(dev->of_node,
+					"samsung,syscon-phandle");
+	if (IS_ERR(sata_phy->pmureg)) {
+		dev_err(dev, "syscon regmap lookup failed.\n");
+		return PTR_ERR(sata_phy->pmureg);
+	}
+
+	node = of_parse_phandle(dev->of_node,
+			"samsung,exynos-sataphy-i2c-phandle", 0);
+	if (!node)
+		return -EINVAL;
+
+	sata_phy->client = of_find_i2c_device_by_node(node);
+	of_node_put(node);
+	if (!sata_phy->client)
+		return -EPROBE_DEFER;
+
+	dev_set_drvdata(dev, sata_phy);
+
+	sata_phy->phyclk = devm_clk_get(dev, "sata_phyctrl");
+	if (IS_ERR(sata_phy->phyclk)) {
+		dev_err(dev, "failed to get clk for PHY\n");
+		ret = PTR_ERR(sata_phy->phyclk);
+		goto put_dev;
+	}
+
+	ret = clk_prepare_enable(sata_phy->phyclk);
+	if (ret < 0) {
+		dev_err(dev, "failed to enable source clk\n");
+		goto put_dev;
+	}
+
+	sata_phy->phy = devm_phy_create(dev, NULL, &exynos_sata_phy_ops);
+	if (IS_ERR(sata_phy->phy)) {
+		dev_err(dev, "failed to create PHY\n");
+		ret = PTR_ERR(sata_phy->phy);
+		goto clk_disable;
+	}
+
+	phy_set_drvdata(sata_phy->phy, sata_phy);
+
+	phy_provider = devm_of_phy_provider_register(dev,
+					of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		ret = PTR_ERR(phy_provider);
+		goto clk_disable;
+	}
+
+	return 0;
+
+clk_disable:
+	clk_disable_unprepare(sata_phy->phyclk);
+put_dev:
+	put_device(&sata_phy->client->dev);
+
+	return ret;
+}
+
+static const struct of_device_id exynos_sata_phy_of_match[] = {
+	{ .compatible = "samsung,exynos5250-sata-phy" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, exynos_sata_phy_of_match);
+
+static struct platform_driver exynos_sata_phy_driver = {
+	.probe	= exynos_sata_phy_probe,
+	.driver = {
+		.of_match_table	= exynos_sata_phy_of_match,
+		.name  = "samsung,sata-phy",
+	}
+};
+module_platform_driver(exynos_sata_phy_driver);
+
+MODULE_DESCRIPTION("Samsung SerDes PHY driver");
+MODULE_LICENSE("GPL v2");
+MODULE_AUTHOR("Girish K S <ks.giri@samsung.com>");
+MODULE_AUTHOR("Yuvaraj C D <yuvaraj.cd@samsung.com>");
diff --git a/drivers/phy/samsung/phy-exynos5250-usb2.c b/drivers/phy/samsung/phy-exynos5250-usb2.c
new file mode 100644
index 000000000..aad806272
--- /dev/null
+++ b/drivers/phy/samsung/phy-exynos5250-usb2.c
@@ -0,0 +1,401 @@
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver - Exynos 5250 support
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/phy/phy.h>
+#include <linux/regmap.h>
+#include "phy-samsung-usb2.h"
+
+/* Exynos USB PHY registers */
+#define EXYNOS_5250_REFCLKSEL_CRYSTAL	0x0
+#define EXYNOS_5250_REFCLKSEL_XO	0x1
+#define EXYNOS_5250_REFCLKSEL_CLKCORE	0x2
+
+#define EXYNOS_5250_FSEL_9MHZ6		0x0
+#define EXYNOS_5250_FSEL_10MHZ		0x1
+#define EXYNOS_5250_FSEL_12MHZ		0x2
+#define EXYNOS_5250_FSEL_19MHZ2		0x3
+#define EXYNOS_5250_FSEL_20MHZ		0x4
+#define EXYNOS_5250_FSEL_24MHZ		0x5
+#define EXYNOS_5250_FSEL_50MHZ		0x7
+
+/* Normal host */
+#define EXYNOS_5250_HOSTPHYCTRL0			0x0
+
+#define EXYNOS_5250_HOSTPHYCTRL0_PHYSWRSTALL		BIT(31)
+#define EXYNOS_5250_HOSTPHYCTRL0_REFCLKSEL_SHIFT	19
+#define EXYNOS_5250_HOSTPHYCTRL0_REFCLKSEL_MASK	\
+		(0x3 << EXYNOS_5250_HOSTPHYCTRL0_REFCLKSEL_SHIFT)
+#define EXYNOS_5250_HOSTPHYCTRL0_FSEL_SHIFT		16
+#define EXYNOS_5250_HOSTPHYCTRL0_FSEL_MASK \
+		(0x7 << EXYNOS_5250_HOSTPHYCTRL0_FSEL_SHIFT)
+#define EXYNOS_5250_HOSTPHYCTRL0_TESTBURNIN		BIT(11)
+#define EXYNOS_5250_HOSTPHYCTRL0_RETENABLE		BIT(10)
+#define EXYNOS_5250_HOSTPHYCTRL0_COMMON_ON_N		BIT(9)
+#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_MASK		(0x3 << 7)
+#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_DUAL		(0x0 << 7)
+#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_ID0		(0x1 << 7)
+#define EXYNOS_5250_HOSTPHYCTRL0_VATESTENB_ANALOGTEST	(0x2 << 7)
+#define EXYNOS_5250_HOSTPHYCTRL0_SIDDQ			BIT(6)
+#define EXYNOS_5250_HOSTPHYCTRL0_FORCESLEEP		BIT(5)
+#define EXYNOS_5250_HOSTPHYCTRL0_FORCESUSPEND		BIT(4)
+#define EXYNOS_5250_HOSTPHYCTRL0_WORDINTERFACE		BIT(3)
+#define EXYNOS_5250_HOSTPHYCTRL0_UTMISWRST		BIT(2)
+#define EXYNOS_5250_HOSTPHYCTRL0_LINKSWRST		BIT(1)
+#define EXYNOS_5250_HOSTPHYCTRL0_PHYSWRST		BIT(0)
+
+/* HSIC0 & HSIC1 */
+#define EXYNOS_5250_HSICPHYCTRL1			0x10
+#define EXYNOS_5250_HSICPHYCTRL2			0x20
+
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKSEL_MASK		(0x3 << 23)
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKSEL_DEFAULT	(0x2 << 23)
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_MASK		(0x7f << 16)
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_12		(0x24 << 16)
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_15		(0x1c << 16)
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_16		(0x1a << 16)
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_19_2		(0x15 << 16)
+#define EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_20		(0x14 << 16)
+#define EXYNOS_5250_HSICPHYCTRLX_SIDDQ			BIT(6)
+#define EXYNOS_5250_HSICPHYCTRLX_FORCESLEEP		BIT(5)
+#define EXYNOS_5250_HSICPHYCTRLX_FORCESUSPEND		BIT(4)
+#define EXYNOS_5250_HSICPHYCTRLX_WORDINTERFACE		BIT(3)
+#define EXYNOS_5250_HSICPHYCTRLX_UTMISWRST		BIT(2)
+#define EXYNOS_5250_HSICPHYCTRLX_PHYSWRST		BIT(0)
+
+/* EHCI control */
+#define EXYNOS_5250_HOSTEHCICTRL			0x30
+#define EXYNOS_5250_HOSTEHCICTRL_ENAINCRXALIGN		BIT(29)
+#define EXYNOS_5250_HOSTEHCICTRL_ENAINCR4		BIT(28)
+#define EXYNOS_5250_HOSTEHCICTRL_ENAINCR8		BIT(27)
+#define EXYNOS_5250_HOSTEHCICTRL_ENAINCR16		BIT(26)
+#define EXYNOS_5250_HOSTEHCICTRL_AUTOPPDONOVRCUREN	BIT(25)
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_SHIFT	19
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_MASK	\
+		(0x3f << EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_SHIFT)
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL1_SHIFT	13
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL1_MASK	\
+		(0x3f << EXYNOS_5250_HOSTEHCICTRL_FLADJVAL1_SHIFT)
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL2_SHIFT	7
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_MASK	\
+		(0x3f << EXYNOS_5250_HOSTEHCICTRL_FLADJVAL0_SHIFT)
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVALHOST_SHIFT	1
+#define EXYNOS_5250_HOSTEHCICTRL_FLADJVALHOST_MASK \
+		(0x1 << EXYNOS_5250_HOSTEHCICTRL_FLADJVALHOST_SHIFT)
+#define EXYNOS_5250_HOSTEHCICTRL_SIMULATIONMODE		BIT(0)
+
+/* OHCI control */
+#define EXYNOS_5250_HOSTOHCICTRL                        0x34
+#define EXYNOS_5250_HOSTOHCICTRL_FRAMELENVAL_SHIFT	1
+#define EXYNOS_5250_HOSTOHCICTRL_FRAMELENVAL_MASK \
+		(0x3ff << EXYNOS_5250_HOSTOHCICTRL_FRAMELENVAL_SHIFT)
+#define EXYNOS_5250_HOSTOHCICTRL_FRAMELENVALEN		BIT(0)
+
+/* USBOTG */
+#define EXYNOS_5250_USBOTGSYS				0x38
+#define EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET		BIT(14)
+#define EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG		BIT(13)
+#define EXYNOS_5250_USBOTGSYS_PHY_SW_RST		BIT(12)
+#define EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT		9
+#define EXYNOS_5250_USBOTGSYS_REFCLKSEL_MASK \
+		(0x3 << EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT)
+#define EXYNOS_5250_USBOTGSYS_ID_PULLUP			BIT(8)
+#define EXYNOS_5250_USBOTGSYS_COMMON_ON			BIT(7)
+#define EXYNOS_5250_USBOTGSYS_FSEL_SHIFT		4
+#define EXYNOS_5250_USBOTGSYS_FSEL_MASK \
+		(0x3 << EXYNOS_5250_USBOTGSYS_FSEL_SHIFT)
+#define EXYNOS_5250_USBOTGSYS_FORCE_SLEEP		BIT(3)
+#define EXYNOS_5250_USBOTGSYS_OTGDISABLE		BIT(2)
+#define EXYNOS_5250_USBOTGSYS_SIDDQ_UOTG		BIT(1)
+#define EXYNOS_5250_USBOTGSYS_FORCE_SUSPEND		BIT(0)
+
+/* Isolation, configured in the power management unit */
+#define EXYNOS_5250_USB_ISOL_OTG_OFFSET		0x704
+#define EXYNOS_5250_USB_ISOL_OTG		BIT(0)
+#define EXYNOS_5250_USB_ISOL_HOST_OFFSET	0x708
+#define EXYNOS_5250_USB_ISOL_HOST		BIT(0)
+
+/* Mode swtich register */
+#define EXYNOS_5250_MODE_SWITCH_OFFSET		0x230
+#define EXYNOS_5250_MODE_SWITCH_MASK		1
+#define EXYNOS_5250_MODE_SWITCH_DEVICE		0
+#define EXYNOS_5250_MODE_SWITCH_HOST		1
+
+enum exynos4x12_phy_id {
+	EXYNOS5250_DEVICE,
+	EXYNOS5250_HOST,
+	EXYNOS5250_HSIC0,
+	EXYNOS5250_HSIC1,
+	EXYNOS5250_NUM_PHYS,
+};
+
+/*
+ * exynos5250_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static int exynos5250_rate_to_clk(unsigned long rate, u32 *reg)
+{
+	/* EXYNOS_5250_FSEL_MASK */
+
+	switch (rate) {
+	case 9600 * KHZ:
+		*reg = EXYNOS_5250_FSEL_9MHZ6;
+		break;
+	case 10 * MHZ:
+		*reg = EXYNOS_5250_FSEL_10MHZ;
+		break;
+	case 12 * MHZ:
+		*reg = EXYNOS_5250_FSEL_12MHZ;
+		break;
+	case 19200 * KHZ:
+		*reg = EXYNOS_5250_FSEL_19MHZ2;
+		break;
+	case 20 * MHZ:
+		*reg = EXYNOS_5250_FSEL_20MHZ;
+		break;
+	case 24 * MHZ:
+		*reg = EXYNOS_5250_FSEL_24MHZ;
+		break;
+	case 50 * MHZ:
+		*reg = EXYNOS_5250_FSEL_50MHZ;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void exynos5250_isol(struct samsung_usb2_phy_instance *inst, bool on)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 offset;
+	u32 mask;
+
+	switch (inst->cfg->id) {
+	case EXYNOS5250_DEVICE:
+		offset = EXYNOS_5250_USB_ISOL_OTG_OFFSET;
+		mask = EXYNOS_5250_USB_ISOL_OTG;
+		break;
+	case EXYNOS5250_HOST:
+		offset = EXYNOS_5250_USB_ISOL_HOST_OFFSET;
+		mask = EXYNOS_5250_USB_ISOL_HOST;
+		break;
+	default:
+		return;
+	}
+
+	regmap_update_bits(drv->reg_pmu, offset, mask, on ? 0 : mask);
+}
+
+static int exynos5250_power_on(struct samsung_usb2_phy_instance *inst)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 ctrl0;
+	u32 otg;
+	u32 ehci;
+	u32 ohci;
+	u32 hsic;
+
+	switch (inst->cfg->id) {
+	case EXYNOS5250_DEVICE:
+		regmap_update_bits(drv->reg_sys,
+				   EXYNOS_5250_MODE_SWITCH_OFFSET,
+				   EXYNOS_5250_MODE_SWITCH_MASK,
+				   EXYNOS_5250_MODE_SWITCH_DEVICE);
+
+		/* OTG configuration */
+		otg = readl(drv->reg_phy + EXYNOS_5250_USBOTGSYS);
+		/* The clock */
+		otg &= ~EXYNOS_5250_USBOTGSYS_FSEL_MASK;
+		otg |= drv->ref_reg_val << EXYNOS_5250_USBOTGSYS_FSEL_SHIFT;
+		/* Reset */
+		otg &= ~(EXYNOS_5250_USBOTGSYS_FORCE_SUSPEND |
+			EXYNOS_5250_USBOTGSYS_FORCE_SLEEP |
+			EXYNOS_5250_USBOTGSYS_SIDDQ_UOTG);
+		otg |=	EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
+			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET |
+			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
+			EXYNOS_5250_USBOTGSYS_OTGDISABLE;
+		/* Ref clock */
+		otg &=	~EXYNOS_5250_USBOTGSYS_REFCLKSEL_MASK;
+		otg |=  EXYNOS_5250_REFCLKSEL_CLKCORE <<
+					EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT;
+		writel(otg, drv->reg_phy + EXYNOS_5250_USBOTGSYS);
+		udelay(100);
+		otg &= ~(EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
+			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
+			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET |
+			EXYNOS_5250_USBOTGSYS_OTGDISABLE);
+		writel(otg, drv->reg_phy + EXYNOS_5250_USBOTGSYS);
+
+
+		break;
+	case EXYNOS5250_HOST:
+	case EXYNOS5250_HSIC0:
+	case EXYNOS5250_HSIC1:
+		/* Host registers configuration */
+		ctrl0 = readl(drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
+		/* The clock */
+		ctrl0 &= ~EXYNOS_5250_HOSTPHYCTRL0_FSEL_MASK;
+		ctrl0 |= drv->ref_reg_val <<
+					EXYNOS_5250_HOSTPHYCTRL0_FSEL_SHIFT;
+
+		/* Reset */
+		ctrl0 &=	~(EXYNOS_5250_HOSTPHYCTRL0_PHYSWRST |
+				EXYNOS_5250_HOSTPHYCTRL0_PHYSWRSTALL |
+				EXYNOS_5250_HOSTPHYCTRL0_SIDDQ |
+				EXYNOS_5250_HOSTPHYCTRL0_FORCESUSPEND |
+				EXYNOS_5250_HOSTPHYCTRL0_FORCESLEEP);
+		ctrl0 |=	EXYNOS_5250_HOSTPHYCTRL0_LINKSWRST |
+				EXYNOS_5250_HOSTPHYCTRL0_UTMISWRST |
+				EXYNOS_5250_HOSTPHYCTRL0_COMMON_ON_N;
+		writel(ctrl0, drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
+		udelay(10);
+		ctrl0 &=	~(EXYNOS_5250_HOSTPHYCTRL0_LINKSWRST |
+				EXYNOS_5250_HOSTPHYCTRL0_UTMISWRST);
+		writel(ctrl0, drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
+
+		/* OTG configuration */
+		otg = readl(drv->reg_phy + EXYNOS_5250_USBOTGSYS);
+		/* The clock */
+		otg &= ~EXYNOS_5250_USBOTGSYS_FSEL_MASK;
+		otg |= drv->ref_reg_val << EXYNOS_5250_USBOTGSYS_FSEL_SHIFT;
+		/* Reset */
+		otg &= ~(EXYNOS_5250_USBOTGSYS_FORCE_SUSPEND |
+			EXYNOS_5250_USBOTGSYS_FORCE_SLEEP |
+			EXYNOS_5250_USBOTGSYS_SIDDQ_UOTG);
+		otg |=	EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
+			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET |
+			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
+			EXYNOS_5250_USBOTGSYS_OTGDISABLE;
+		/* Ref clock */
+		otg &=	~EXYNOS_5250_USBOTGSYS_REFCLKSEL_MASK;
+		otg |=  EXYNOS_5250_REFCLKSEL_CLKCORE <<
+					EXYNOS_5250_USBOTGSYS_REFCLKSEL_SHIFT;
+		writel(otg, drv->reg_phy + EXYNOS_5250_USBOTGSYS);
+		udelay(10);
+		otg &= ~(EXYNOS_5250_USBOTGSYS_PHY_SW_RST |
+			EXYNOS_5250_USBOTGSYS_LINK_SW_RST_UOTG |
+			EXYNOS_5250_USBOTGSYS_PHYLINK_SW_RESET);
+
+		/* HSIC phy configuration */
+		hsic = (EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_12 |
+				EXYNOS_5250_HSICPHYCTRLX_REFCLKSEL_DEFAULT |
+				EXYNOS_5250_HSICPHYCTRLX_PHYSWRST);
+		writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL1);
+		writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL2);
+		udelay(10);
+		hsic &= ~EXYNOS_5250_HSICPHYCTRLX_PHYSWRST;
+		writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL1);
+		writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL2);
+		/* The following delay is necessary for the reset sequence to be
+		 * completed */
+		udelay(80);
+
+		/* Enable EHCI DMA burst */
+		ehci = readl(drv->reg_phy + EXYNOS_5250_HOSTEHCICTRL);
+		ehci |=	EXYNOS_5250_HOSTEHCICTRL_ENAINCRXALIGN |
+			EXYNOS_5250_HOSTEHCICTRL_ENAINCR4 |
+			EXYNOS_5250_HOSTEHCICTRL_ENAINCR8 |
+			EXYNOS_5250_HOSTEHCICTRL_ENAINCR16;
+		writel(ehci, drv->reg_phy + EXYNOS_5250_HOSTEHCICTRL);
+
+		/* OHCI settings */
+		ohci = readl(drv->reg_phy + EXYNOS_5250_HOSTOHCICTRL);
+		/* Following code is based on the old driver */
+		ohci |=	0x1 << 3;
+		writel(ohci, drv->reg_phy + EXYNOS_5250_HOSTOHCICTRL);
+
+		break;
+	}
+	exynos5250_isol(inst, 0);
+
+	return 0;
+}
+
+static int exynos5250_power_off(struct samsung_usb2_phy_instance *inst)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 ctrl0;
+	u32 otg;
+	u32 hsic;
+
+	exynos5250_isol(inst, 1);
+
+	switch (inst->cfg->id) {
+	case EXYNOS5250_DEVICE:
+		otg = readl(drv->reg_phy + EXYNOS_5250_USBOTGSYS);
+		otg |= (EXYNOS_5250_USBOTGSYS_FORCE_SUSPEND |
+			EXYNOS_5250_USBOTGSYS_SIDDQ_UOTG |
+			EXYNOS_5250_USBOTGSYS_FORCE_SLEEP);
+		writel(otg, drv->reg_phy + EXYNOS_5250_USBOTGSYS);
+		break;
+	case EXYNOS5250_HOST:
+		ctrl0 = readl(drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
+		ctrl0 |= (EXYNOS_5250_HOSTPHYCTRL0_SIDDQ |
+				EXYNOS_5250_HOSTPHYCTRL0_FORCESUSPEND |
+				EXYNOS_5250_HOSTPHYCTRL0_FORCESLEEP |
+				EXYNOS_5250_HOSTPHYCTRL0_PHYSWRST |
+				EXYNOS_5250_HOSTPHYCTRL0_PHYSWRSTALL);
+		writel(ctrl0, drv->reg_phy + EXYNOS_5250_HOSTPHYCTRL0);
+		break;
+	case EXYNOS5250_HSIC0:
+	case EXYNOS5250_HSIC1:
+		hsic = (EXYNOS_5250_HSICPHYCTRLX_REFCLKDIV_12 |
+				EXYNOS_5250_HSICPHYCTRLX_REFCLKSEL_DEFAULT |
+				EXYNOS_5250_HSICPHYCTRLX_SIDDQ |
+				EXYNOS_5250_HSICPHYCTRLX_FORCESLEEP |
+				EXYNOS_5250_HSICPHYCTRLX_FORCESUSPEND
+				);
+		writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL1);
+		writel(hsic, drv->reg_phy + EXYNOS_5250_HSICPHYCTRL2);
+		break;
+	}
+
+	return 0;
+}
+
+
+static const struct samsung_usb2_common_phy exynos5250_phys[] = {
+	{
+		.label		= "device",
+		.id		= EXYNOS5250_DEVICE,
+		.power_on	= exynos5250_power_on,
+		.power_off	= exynos5250_power_off,
+	},
+	{
+		.label		= "host",
+		.id		= EXYNOS5250_HOST,
+		.power_on	= exynos5250_power_on,
+		.power_off	= exynos5250_power_off,
+	},
+	{
+		.label		= "hsic0",
+		.id		= EXYNOS5250_HSIC0,
+		.power_on	= exynos5250_power_on,
+		.power_off	= exynos5250_power_off,
+	},
+	{
+		.label		= "hsic1",
+		.id		= EXYNOS5250_HSIC1,
+		.power_on	= exynos5250_power_on,
+		.power_off	= exynos5250_power_off,
+	},
+};
+
+const struct samsung_usb2_phy_config exynos5250_usb2_phy_config = {
+	.has_mode_switch	= 1,
+	.num_phys		= EXYNOS5250_NUM_PHYS,
+	.phys			= exynos5250_phys,
+	.rate_to_clk		= exynos5250_rate_to_clk,
+};
diff --git a/drivers/phy/samsung/phy-s5pv210-usb2.c b/drivers/phy/samsung/phy-s5pv210-usb2.c
new file mode 100644
index 000000000..bb7fdf491
--- /dev/null
+++ b/drivers/phy/samsung/phy-s5pv210-usb2.c
@@ -0,0 +1,191 @@
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver - S5PV210 support
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Authors: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/phy/phy.h>
+#include "phy-samsung-usb2.h"
+
+/* Exynos USB PHY registers */
+
+/* PHY power control */
+#define S5PV210_UPHYPWR			0x0
+
+#define S5PV210_UPHYPWR_PHY0_SUSPEND	BIT(0)
+#define S5PV210_UPHYPWR_PHY0_PWR	BIT(3)
+#define S5PV210_UPHYPWR_PHY0_OTG_PWR	BIT(4)
+#define S5PV210_UPHYPWR_PHY0	( \
+	S5PV210_UPHYPWR_PHY0_SUSPEND | \
+	S5PV210_UPHYPWR_PHY0_PWR | \
+	S5PV210_UPHYPWR_PHY0_OTG_PWR)
+
+#define S5PV210_UPHYPWR_PHY1_SUSPEND	BIT(6)
+#define S5PV210_UPHYPWR_PHY1_PWR	BIT(7)
+#define S5PV210_UPHYPWR_PHY1 ( \
+	S5PV210_UPHYPWR_PHY1_SUSPEND | \
+	S5PV210_UPHYPWR_PHY1_PWR)
+
+/* PHY clock control */
+#define S5PV210_UPHYCLK			0x4
+
+#define S5PV210_UPHYCLK_PHYFSEL_MASK	(0x3 << 0)
+#define S5PV210_UPHYCLK_PHYFSEL_48MHZ	(0x0 << 0)
+#define S5PV210_UPHYCLK_PHYFSEL_24MHZ	(0x3 << 0)
+#define S5PV210_UPHYCLK_PHYFSEL_12MHZ	(0x2 << 0)
+
+#define S5PV210_UPHYCLK_PHY0_ID_PULLUP	BIT(2)
+#define S5PV210_UPHYCLK_PHY0_COMMON_ON	BIT(4)
+#define S5PV210_UPHYCLK_PHY1_COMMON_ON	BIT(7)
+
+/* PHY reset control */
+#define S5PV210_UPHYRST			0x8
+
+#define S5PV210_URSTCON_PHY0		BIT(0)
+#define S5PV210_URSTCON_OTG_HLINK	BIT(1)
+#define S5PV210_URSTCON_OTG_PHYLINK	BIT(2)
+#define S5PV210_URSTCON_PHY1_ALL	BIT(3)
+#define S5PV210_URSTCON_HOST_LINK_ALL	BIT(4)
+
+/* Isolation, configured in the power management unit */
+#define S5PV210_USB_ISOL_OFFSET		0x680c
+#define S5PV210_USB_ISOL_DEVICE		BIT(0)
+#define S5PV210_USB_ISOL_HOST		BIT(1)
+
+
+enum s5pv210_phy_id {
+	S5PV210_DEVICE,
+	S5PV210_HOST,
+	S5PV210_NUM_PHYS,
+};
+
+/*
+ * s5pv210_rate_to_clk() converts the supplied clock rate to the value that
+ * can be written to the phy register.
+ */
+static int s5pv210_rate_to_clk(unsigned long rate, u32 *reg)
+{
+	switch (rate) {
+	case 12 * MHZ:
+		*reg = S5PV210_UPHYCLK_PHYFSEL_12MHZ;
+		break;
+	case 24 * MHZ:
+		*reg = S5PV210_UPHYCLK_PHYFSEL_24MHZ;
+		break;
+	case 48 * MHZ:
+		*reg = S5PV210_UPHYCLK_PHYFSEL_48MHZ;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static void s5pv210_isol(struct samsung_usb2_phy_instance *inst, bool on)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 mask;
+
+	switch (inst->cfg->id) {
+	case S5PV210_DEVICE:
+		mask = S5PV210_USB_ISOL_DEVICE;
+		break;
+	case S5PV210_HOST:
+		mask = S5PV210_USB_ISOL_HOST;
+		break;
+	default:
+		return;
+	}
+
+	regmap_update_bits(drv->reg_pmu, S5PV210_USB_ISOL_OFFSET,
+							mask, on ? 0 : mask);
+}
+
+static void s5pv210_phy_pwr(struct samsung_usb2_phy_instance *inst, bool on)
+{
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	u32 rstbits = 0;
+	u32 phypwr = 0;
+	u32 rst;
+	u32 pwr;
+
+	switch (inst->cfg->id) {
+	case S5PV210_DEVICE:
+		phypwr =	S5PV210_UPHYPWR_PHY0;
+		rstbits =	S5PV210_URSTCON_PHY0;
+		break;
+	case S5PV210_HOST:
+		phypwr =	S5PV210_UPHYPWR_PHY1;
+		rstbits =	S5PV210_URSTCON_PHY1_ALL |
+				S5PV210_URSTCON_HOST_LINK_ALL;
+		break;
+	}
+
+	if (on) {
+		writel(drv->ref_reg_val, drv->reg_phy + S5PV210_UPHYCLK);
+
+		pwr = readl(drv->reg_phy + S5PV210_UPHYPWR);
+		pwr &= ~phypwr;
+		writel(pwr, drv->reg_phy + S5PV210_UPHYPWR);
+
+		rst = readl(drv->reg_phy + S5PV210_UPHYRST);
+		rst |= rstbits;
+		writel(rst, drv->reg_phy + S5PV210_UPHYRST);
+		udelay(10);
+		rst &= ~rstbits;
+		writel(rst, drv->reg_phy + S5PV210_UPHYRST);
+		/* The following delay is necessary for the reset sequence to be
+		 * completed
+		 */
+		udelay(80);
+	} else {
+		pwr = readl(drv->reg_phy + S5PV210_UPHYPWR);
+		pwr |= phypwr;
+		writel(pwr, drv->reg_phy + S5PV210_UPHYPWR);
+	}
+}
+
+static int s5pv210_power_on(struct samsung_usb2_phy_instance *inst)
+{
+	s5pv210_isol(inst, 0);
+	s5pv210_phy_pwr(inst, 1);
+
+	return 0;
+}
+
+static int s5pv210_power_off(struct samsung_usb2_phy_instance *inst)
+{
+	s5pv210_phy_pwr(inst, 0);
+	s5pv210_isol(inst, 1);
+
+	return 0;
+}
+
+static const struct samsung_usb2_common_phy s5pv210_phys[S5PV210_NUM_PHYS] = {
+	[S5PV210_DEVICE] = {
+		.label		= "device",
+		.id		= S5PV210_DEVICE,
+		.power_on	= s5pv210_power_on,
+		.power_off	= s5pv210_power_off,
+	},
+	[S5PV210_HOST] = {
+		.label		= "host",
+		.id		= S5PV210_HOST,
+		.power_on	= s5pv210_power_on,
+		.power_off	= s5pv210_power_off,
+	},
+};
+
+const struct samsung_usb2_phy_config s5pv210_usb2_phy_config = {
+	.num_phys	= ARRAY_SIZE(s5pv210_phys),
+	.phys		= s5pv210_phys,
+	.rate_to_clk	= s5pv210_rate_to_clk,
+};
diff --git a/drivers/phy/samsung/phy-samsung-usb2.c b/drivers/phy/samsung/phy-samsung-usb2.c
new file mode 100644
index 000000000..ea8188669
--- /dev/null
+++ b/drivers/phy/samsung/phy-samsung-usb2.c
@@ -0,0 +1,264 @@
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/spinlock.h>
+#include "phy-samsung-usb2.h"
+
+static int samsung_usb2_phy_power_on(struct phy *phy)
+{
+	struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy);
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	int ret;
+
+	dev_dbg(drv->dev, "Request to power_on \"%s\" usb phy\n",
+		inst->cfg->label);
+
+	if (drv->vbus) {
+		ret = regulator_enable(drv->vbus);
+		if (ret)
+			goto err_regulator;
+	}
+
+	ret = clk_prepare_enable(drv->clk);
+	if (ret)
+		goto err_main_clk;
+	ret = clk_prepare_enable(drv->ref_clk);
+	if (ret)
+		goto err_instance_clk;
+	if (inst->cfg->power_on) {
+		spin_lock(&drv->lock);
+		ret = inst->cfg->power_on(inst);
+		spin_unlock(&drv->lock);
+		if (ret)
+			goto err_power_on;
+	}
+
+	return 0;
+
+err_power_on:
+	clk_disable_unprepare(drv->ref_clk);
+err_instance_clk:
+	clk_disable_unprepare(drv->clk);
+err_main_clk:
+	if (drv->vbus)
+		regulator_disable(drv->vbus);
+err_regulator:
+	return ret;
+}
+
+static int samsung_usb2_phy_power_off(struct phy *phy)
+{
+	struct samsung_usb2_phy_instance *inst = phy_get_drvdata(phy);
+	struct samsung_usb2_phy_driver *drv = inst->drv;
+	int ret = 0;
+
+	dev_dbg(drv->dev, "Request to power_off \"%s\" usb phy\n",
+		inst->cfg->label);
+	if (inst->cfg->power_off) {
+		spin_lock(&drv->lock);
+		ret = inst->cfg->power_off(inst);
+		spin_unlock(&drv->lock);
+		if (ret)
+			return ret;
+	}
+	clk_disable_unprepare(drv->ref_clk);
+	clk_disable_unprepare(drv->clk);
+	if (drv->vbus)
+		ret = regulator_disable(drv->vbus);
+
+	return ret;
+}
+
+static const struct phy_ops samsung_usb2_phy_ops = {
+	.power_on	= samsung_usb2_phy_power_on,
+	.power_off	= samsung_usb2_phy_power_off,
+	.owner		= THIS_MODULE,
+};
+
+static struct phy *samsung_usb2_phy_xlate(struct device *dev,
+					struct of_phandle_args *args)
+{
+	struct samsung_usb2_phy_driver *drv;
+
+	drv = dev_get_drvdata(dev);
+	if (!drv)
+		return ERR_PTR(-EINVAL);
+
+	if (WARN_ON(args->args[0] >= drv->cfg->num_phys))
+		return ERR_PTR(-ENODEV);
+
+	return drv->instances[args->args[0]].phy;
+}
+
+static const struct of_device_id samsung_usb2_phy_of_match[] = {
+#ifdef CONFIG_PHY_EXYNOS4X12_USB2
+	{
+		.compatible = "samsung,exynos3250-usb2-phy",
+		.data = &exynos3250_usb2_phy_config,
+	},
+#endif
+#ifdef CONFIG_PHY_EXYNOS4210_USB2
+	{
+		.compatible = "samsung,exynos4210-usb2-phy",
+		.data = &exynos4210_usb2_phy_config,
+	},
+#endif
+#ifdef CONFIG_PHY_EXYNOS4X12_USB2
+	{
+		.compatible = "samsung,exynos4x12-usb2-phy",
+		.data = &exynos4x12_usb2_phy_config,
+	},
+#endif
+#ifdef CONFIG_PHY_EXYNOS5250_USB2
+	{
+		.compatible = "samsung,exynos5250-usb2-phy",
+		.data = &exynos5250_usb2_phy_config,
+	},
+#endif
+#ifdef CONFIG_PHY_S5PV210_USB2
+	{
+		.compatible = "samsung,s5pv210-usb2-phy",
+		.data = &s5pv210_usb2_phy_config,
+	},
+#endif
+	{ },
+};
+MODULE_DEVICE_TABLE(of, samsung_usb2_phy_of_match);
+
+static int samsung_usb2_phy_probe(struct platform_device *pdev)
+{
+	const struct samsung_usb2_phy_config *cfg;
+	struct device *dev = &pdev->dev;
+	struct phy_provider *phy_provider;
+	struct resource *mem;
+	struct samsung_usb2_phy_driver *drv;
+	int i, ret;
+
+	if (!pdev->dev.of_node) {
+		dev_err(dev, "This driver is required to be instantiated from device tree\n");
+		return -EINVAL;
+	}
+
+	cfg = of_device_get_match_data(dev);
+	if (!cfg)
+		return -EINVAL;
+
+	drv = devm_kzalloc(dev, sizeof(struct samsung_usb2_phy_driver) +
+		cfg->num_phys * sizeof(struct samsung_usb2_phy_instance),
+								GFP_KERNEL);
+	if (!drv)
+		return -ENOMEM;
+
+	dev_set_drvdata(dev, drv);
+	spin_lock_init(&drv->lock);
+
+	drv->cfg = cfg;
+	drv->dev = dev;
+
+	mem = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	drv->reg_phy = devm_ioremap_resource(dev, mem);
+	if (IS_ERR(drv->reg_phy)) {
+		dev_err(dev, "Failed to map register memory (phy)\n");
+		return PTR_ERR(drv->reg_phy);
+	}
+
+	drv->reg_pmu = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+		"samsung,pmureg-phandle");
+	if (IS_ERR(drv->reg_pmu)) {
+		dev_err(dev, "Failed to map PMU registers (via syscon)\n");
+		return PTR_ERR(drv->reg_pmu);
+	}
+
+	if (drv->cfg->has_mode_switch) {
+		drv->reg_sys = syscon_regmap_lookup_by_phandle(
+				pdev->dev.of_node, "samsung,sysreg-phandle");
+		if (IS_ERR(drv->reg_sys)) {
+			dev_err(dev, "Failed to map system registers (via syscon)\n");
+			return PTR_ERR(drv->reg_sys);
+		}
+	}
+
+	drv->clk = devm_clk_get(dev, "phy");
+	if (IS_ERR(drv->clk)) {
+		dev_err(dev, "Failed to get clock of phy controller\n");
+		return PTR_ERR(drv->clk);
+	}
+
+	drv->ref_clk = devm_clk_get(dev, "ref");
+	if (IS_ERR(drv->ref_clk)) {
+		dev_err(dev, "Failed to get reference clock for the phy controller\n");
+		return PTR_ERR(drv->ref_clk);
+	}
+
+	drv->ref_rate = clk_get_rate(drv->ref_clk);
+	if (drv->cfg->rate_to_clk) {
+		ret = drv->cfg->rate_to_clk(drv->ref_rate, &drv->ref_reg_val);
+		if (ret)
+			return ret;
+	}
+
+	drv->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(drv->vbus)) {
+		ret = PTR_ERR(drv->vbus);
+		if (ret == -EPROBE_DEFER)
+			return ret;
+		drv->vbus = NULL;
+	}
+
+	for (i = 0; i < drv->cfg->num_phys; i++) {
+		char *label = drv->cfg->phys[i].label;
+		struct samsung_usb2_phy_instance *p = &drv->instances[i];
+
+		dev_dbg(dev, "Creating phy \"%s\"\n", label);
+		p->phy = devm_phy_create(dev, NULL, &samsung_usb2_phy_ops);
+		if (IS_ERR(p->phy)) {
+			dev_err(drv->dev, "Failed to create usb2_phy \"%s\"\n",
+				label);
+			return PTR_ERR(p->phy);
+		}
+
+		p->cfg = &drv->cfg->phys[i];
+		p->drv = drv;
+		phy_set_bus_width(p->phy, 8);
+		phy_set_drvdata(p->phy, p);
+	}
+
+	phy_provider = devm_of_phy_provider_register(dev,
+							samsung_usb2_phy_xlate);
+	if (IS_ERR(phy_provider)) {
+		dev_err(drv->dev, "Failed to register phy provider\n");
+		return PTR_ERR(phy_provider);
+	}
+
+	return 0;
+}
+
+static struct platform_driver samsung_usb2_phy_driver = {
+	.probe	= samsung_usb2_phy_probe,
+	.driver = {
+		.of_match_table	= samsung_usb2_phy_of_match,
+		.name		= "samsung-usb2-phy",
+	}
+};
+
+module_platform_driver(samsung_usb2_phy_driver);
+MODULE_DESCRIPTION("Samsung S5P/EXYNOS SoC USB PHY driver");
+MODULE_AUTHOR("Kamil Debski <k.debski@samsung.com>");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:samsung-usb2-phy");
diff --git a/drivers/phy/samsung/phy-samsung-usb2.h b/drivers/phy/samsung/phy-samsung-usb2.h
new file mode 100644
index 000000000..6563e7ca0
--- /dev/null
+++ b/drivers/phy/samsung/phy-samsung-usb2.h
@@ -0,0 +1,73 @@
+/*
+ * Samsung SoC USB 1.1/2.0 PHY driver
+ *
+ * Copyright (C) 2013 Samsung Electronics Co., Ltd.
+ * Author: Kamil Debski <k.debski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef _PHY_EXYNOS_USB2_H
+#define _PHY_EXYNOS_USB2_H
+
+#include <linux/clk.h>
+#include <linux/phy/phy.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+#include <linux/spinlock.h>
+#include <linux/regulator/consumer.h>
+
+#define KHZ 1000
+#define MHZ (KHZ * KHZ)
+
+struct samsung_usb2_phy_driver;
+struct samsung_usb2_phy_instance;
+struct samsung_usb2_phy_config;
+
+struct samsung_usb2_phy_instance {
+	const struct samsung_usb2_common_phy *cfg;
+	struct phy *phy;
+	struct samsung_usb2_phy_driver *drv;
+	int int_cnt;
+	int ext_cnt;
+};
+
+struct samsung_usb2_phy_driver {
+	const struct samsung_usb2_phy_config *cfg;
+	struct clk *clk;
+	struct clk *ref_clk;
+	struct regulator *vbus;
+	unsigned long ref_rate;
+	u32 ref_reg_val;
+	struct device *dev;
+	void __iomem *reg_phy;
+	struct regmap *reg_pmu;
+	struct regmap *reg_sys;
+	spinlock_t lock;
+	struct samsung_usb2_phy_instance instances[0];
+};
+
+struct samsung_usb2_common_phy {
+	int (*power_on)(struct samsung_usb2_phy_instance *);
+	int (*power_off)(struct samsung_usb2_phy_instance *);
+	unsigned int id;
+	char *label;
+};
+
+
+struct samsung_usb2_phy_config {
+	const struct samsung_usb2_common_phy *phys;
+	int (*rate_to_clk)(unsigned long, u32 *);
+	unsigned int num_phys;
+	bool has_mode_switch;
+	bool has_refclk_sel;
+};
+
+extern const struct samsung_usb2_phy_config exynos3250_usb2_phy_config;
+extern const struct samsung_usb2_phy_config exynos4210_usb2_phy_config;
+extern const struct samsung_usb2_phy_config exynos4x12_usb2_phy_config;
+extern const struct samsung_usb2_phy_config exynos5250_usb2_phy_config;
+extern const struct samsung_usb2_phy_config s5pv210_usb2_phy_config;
+#endif