summaryrefslogtreecommitdiffstats
path: root/Documentation/EDID/HOWTO.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/EDID/HOWTO.txt')
-rw-r--r--Documentation/EDID/HOWTO.txt58
1 files changed, 58 insertions, 0 deletions
diff --git a/Documentation/EDID/HOWTO.txt b/Documentation/EDID/HOWTO.txt
new file mode 100644
index 000000000..835db3322
--- /dev/null
+++ b/Documentation/EDID/HOWTO.txt
@@ -0,0 +1,58 @@
+In the good old days when graphics parameters were configured explicitly
+in a file called xorg.conf, even broken hardware could be managed.
+
+Today, with the advent of Kernel Mode Setting, a graphics board is
+either correctly working because all components follow the standards -
+or the computer is unusable, because the screen remains dark after
+booting or it displays the wrong area. Cases when this happens are:
+- The graphics board does not recognize the monitor.
+- The graphics board is unable to detect any EDID data.
+- The graphics board incorrectly forwards EDID data to the driver.
+- The monitor sends no or bogus EDID data.
+- A KVM sends its own EDID data instead of querying the connected monitor.
+Adding the kernel parameter "nomodeset" helps in most cases, but causes
+restrictions later on.
+
+As a remedy for such situations, the kernel configuration item
+CONFIG_DRM_LOAD_EDID_FIRMWARE was introduced. It allows to provide an
+individually prepared or corrected EDID data set in the /lib/firmware
+directory from where it is loaded via the firmware interface. The code
+(see drivers/gpu/drm/drm_edid_load.c) contains built-in data sets for
+commonly used screen resolutions (800x600, 1024x768, 1280x1024, 1600x1200,
+1680x1050, 1920x1080) as binary blobs, but the kernel source tree does
+not contain code to create these data. In order to elucidate the origin
+of the built-in binary EDID blobs and to facilitate the creation of
+individual data for a specific misbehaving monitor, commented sources
+and a Makefile environment are given here.
+
+To create binary EDID and C source code files from the existing data
+material, simply type "make".
+
+If you want to create your own EDID file, copy the file 1024x768.S,
+replace the settings with your own data and add a new target to the
+Makefile. Please note that the EDID data structure expects the timing
+values in a different way as compared to the standard X11 format.
+
+X11:
+HTimings: hdisp hsyncstart hsyncend htotal
+VTimings: vdisp vsyncstart vsyncend vtotal
+
+EDID:
+#define XPIX hdisp
+#define XBLANK htotal-hdisp
+#define XOFFSET hsyncstart-hdisp
+#define XPULSE hsyncend-hsyncstart
+
+#define YPIX vdisp
+#define YBLANK vtotal-vdisp
+#define YOFFSET (63+(vsyncstart-vdisp))
+#define YPULSE (63+(vsyncend-vsyncstart))
+
+The CRC value in the last line
+ #define CRC 0x55
+also is a bit tricky. After a first version of the binary data set is
+created, it must be checked with the "edid-decode" utility which will
+most probably complain about a wrong CRC. Fortunately, the utility also
+displays the correct CRC which must then be inserted into the source
+file. After the make procedure is repeated, the EDID data set is ready
+to be used.