diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock/at91-clock.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/clock/at91-clock.txt | 536 |
1 files changed, 536 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/clock/at91-clock.txt b/Documentation/devicetree/bindings/clock/at91-clock.txt new file mode 100644 index 000000000..8f8f95056 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/at91-clock.txt @@ -0,0 +1,536 @@ +Device Tree Clock bindings for arch-at91 + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be one of the following: + "atmel,at91sam9x5-sckc" or + "atmel,sama5d4-sckc": + at91 SCKC (Slow Clock Controller) + This node contains the slow clock definitions. + + "atmel,at91sam9x5-clk-slow-osc": + at91 slow oscillator + + "atmel,at91sam9x5-clk-slow-rc-osc": + at91 internal slow RC oscillator + + "atmel,<chip>-pmc": + at91 PMC (Power Management Controller) + All at91 specific clocks (clocks defined below) must be child + node of the PMC node. + <chip> can be: at91rm9200, at91sam9260, at91sam9261, + at91sam9263, at91sam9g45, at91sam9n12, at91sam9rl, at91sam9x5, + sama5d2, sama5d3 or sama5d4. + + "atmel,at91sam9x5-clk-slow" (under sckc node) + or + "atmel,at91sam9260-clk-slow" (under pmc node): + at91 slow clk + + "atmel,at91rm9200-clk-main-osc" + "atmel,at91sam9x5-clk-main-rc-osc" + at91 main clk sources + + "atmel,at91sam9x5-clk-main" + "atmel,at91rm9200-clk-main": + at91 main clock + + "atmel,at91rm9200-clk-master" or + "atmel,at91sam9x5-clk-master": + at91 master clock + + "atmel,at91sam9x5-clk-peripheral" or + "atmel,at91rm9200-clk-peripheral": + at91 peripheral clocks + + "atmel,at91rm9200-clk-pll" or + "atmel,at91sam9g45-clk-pll" or + "atmel,at91sam9g20-clk-pllb" or + "atmel,sama5d3-clk-pll": + at91 pll clocks + + "atmel,at91sam9x5-clk-plldiv": + at91 plla divisor + + "atmel,at91rm9200-clk-programmable" or + "atmel,at91sam9g45-clk-programmable" or + "atmel,at91sam9x5-clk-programmable": + at91 programmable clocks + + "atmel,at91sam9x5-clk-smd": + at91 SMD (Soft Modem) clock + + "atmel,at91rm9200-clk-system": + at91 system clocks + + "atmel,at91rm9200-clk-usb" or + "atmel,at91sam9x5-clk-usb" or + "atmel,at91sam9n12-clk-usb": + at91 usb clock + + "atmel,at91sam9x5-clk-utmi": + at91 utmi clock + + "atmel,sama5d4-clk-h32mx": + at91 h32mx clock + + "atmel,sama5d2-clk-generated": + at91 generated clock + + "atmel,sama5d2-clk-audio-pll-frac": + at91 audio fractional pll + + "atmel,sama5d2-clk-audio-pll-pad": + at91 audio pll CLK_AUDIO output pin + + "atmel,sama5d2-clk-audio-pll-pmc" + at91 audio pll output on AUDIOPLLCLK that feeds the PMC + and can be used by peripheral clock or generic clock + + "atmel,sama5d2-clk-i2s-mux" (under pmc node): + at91 I2S clock source selection + +Required properties for SCKC node: +- reg : defines the IO memory reserved for the SCKC. +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). + + +For example: + sckc: sckc@fffffe50 { + compatible = "atmel,sama5d3-pmc"; + reg = <0xfffffe50 0x4> + #size-cells = <0>; + #address-cells = <1>; + + /* put at91 slow clocks here */ + }; + + +Required properties for internal slow RC oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + slow_rc_osc: slow_rc_osc { + compatible = "atmel,at91sam9x5-clk-slow-rc-osc"; + clock-frequency = <32768>; + clock-accuracy = <50000000>; + }; + +Required properties for slow oscillator: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Set this when a clock signal is directly + provided on XIN. + +For example: + slow_osc: slow_osc { + compatible = "atmel,at91rm9200-clk-slow-osc"; + #clock-cells = <0>; + clocks = <&slow_xtal>; + }; + +Required properties for slow clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the slow clk sources (see atmel datasheet). + +For example: + clk32k: slck { + compatible = "atmel,at91sam9x5-clk-slow"; + #clock-cells = <0>; + clocks = <&slow_rc_osc &slow_osc>; + }; + +Required properties for PMC node: +- reg : defines the IO memory reserved for the PMC. +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- interrupts : shall be set to PMC interrupt line. +- interrupt-controller : tell that the PMC is an interrupt controller. +- #interrupt-cells : must be set to 1. The first cell encodes the interrupt id, + and reflect the bit position in the PMC_ER/DR/SR registers. + You can use the dt macros defined in dt-bindings/clock/at91.h. + 0 (AT91_PMC_MOSCS) -> main oscillator ready + 1 (AT91_PMC_LOCKA) -> PLL A ready + 2 (AT91_PMC_LOCKB) -> PLL B ready + 3 (AT91_PMC_MCKRDY) -> master clock ready + 6 (AT91_PMC_LOCKU) -> UTMI PLL clock ready + 8 .. 15 (AT91_PMC_PCKRDY(id)) -> programmable clock ready + 16 (AT91_PMC_MOSCSELS) -> main oscillator selected + 17 (AT91_PMC_MOSCRCS) -> RC main oscillator stabilized + 18 (AT91_PMC_CFDEV) -> clock failure detected + +For example: + pmc: pmc@fffffc00 { + compatible = "atmel,sama5d3-pmc"; + interrupts = <1 4 7>; + interrupt-controller; + #interrupt-cells = <2>; + #size-cells = <0>; + #address-cells = <1>; + + /* put at91 clocks here */ + }; + +Required properties for main clock internal RC oscillator: +- interrupts : shall be set to "<0>". +- clock-frequency : define the internal RC oscillator frequency. + +Optional properties: +- clock-accuracy : define the internal RC oscillator accuracy. + +For example: + main_rc_osc: main_rc_osc { + compatible = "atmel,at91sam9x5-clk-main-rc-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + clock-frequency = <12000000>; + clock-accuracy = <50000000>; + }; + +Required properties for main clock oscillator: +- interrupts : shall be set to "<0>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main osc source clk sources (see atmel datasheet). + +Optional properties: +- atmel,osc-bypass : boolean property. Specified if a clock signal is provided + on XIN. + + clock signal is directly provided on XIN pin. + +For example: + main_osc: main_osc { + compatible = "atmel,at91rm9200-clk-main-osc"; + interrupt-parent = <&pmc>; + interrupts = <0>; + #clock-cells = <0>; + clocks = <&main_xtal>; + }; + +Required properties for main clock: +- interrupts : shall be set to "<0>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall encode the main clk sources (see atmel datasheet). + +For example: + main: mainck { + compatible = "atmel,at91sam9x5-clk-main"; + interrupt-parent = <&pmc>; + interrupts = <0>; + #clock-cells = <0>; + clocks = <&main_rc_osc &main_osc>; + }; + +Required properties for master clock: +- interrupts : shall be set to "<3>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the master clock sources (see atmel datasheet) phandles. + e.g. "<&ck32k>, <&main>, <&plla>, <&pllb>". +- atmel,clk-output-range : minimum and maximum clock frequency (two u32 + fields). + e.g. output = <0 133000000>; <=> 0 to 133MHz. +- atmel,clk-divisors : master clock divisors table (four u32 fields). + 0 <=> reserved value. + e.g. divisors = <1 2 4 6>; +- atmel,master-clk-have-div3-pres : some SoC use the reserved value 7 in the + PRES field as CLOCK_DIV3 (e.g sam9x5). + +For example: + mck: mck { + compatible = "atmel,at91rm9200-clk-master"; + interrupt-parent = <&pmc>; + interrupts = <3>; + #clock-cells = <0>; + atmel,clk-output-range = <0 133000000>; + atmel,clk-divisors = <1 2 4 0>; + }; + +Required properties for peripheral clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- clocks : shall be the master clock phandle. + e.g. clocks = <&mck>; +- name: device tree node describing a specific peripheral clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg: peripheral id. See Atmel's datasheets to get a full + list of peripheral ids. + * atmel,clk-output-range : minimum and maximum clock frequency + (two u32 fields). Only valid on at91sam9x5-clk-peripheral + compatible IPs. + +For example: + periph: periphck { + compatible = "atmel,at91sam9x5-clk-peripheral"; + #size-cells = <0>; + #address-cells = <1>; + clocks = <&mck>; + + ssc0_clk { + #clock-cells = <0>; + reg = <2>; + atmel,clk-output-range = <0 133000000>; + }; + + usart0_clk { + #clock-cells = <0>; + reg = <3>; + atmel,clk-output-range = <0 66000000>; + }; + }; + + +Required properties for pll clocks: +- interrupts : shall be set to "<1>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the main clock phandle. +- reg : pll id. + 0 -> PLL A + 1 -> PLL B +- atmel,clk-input-range : minimum and maximum source clock frequency (two u32 + fields). + e.g. input = <1 32000000>; <=> 1 to 32MHz. +- #atmel,pll-clk-output-range-cells : number of cells reserved for pll output + range description. Sould be set to 2, 3 + or 4. + * 1st and 2nd cells represent the frequency range (min-max). + * 3rd cell is optional and represents the OUT field value for the given + range. + * 4th cell is optional and represents the ICPLL field (PLLICPR + register) +- atmel,pll-clk-output-ranges : pll output frequency ranges + optional parameter + depending on #atmel,pll-output-range-cells + property value. + +For example: + plla: pllack { + compatible = "atmel,at91sam9g45-clk-pll"; + interrupt-parent = <&pmc>; + interrupts = <1>; + #clock-cells = <0>; + clocks = <&main>; + reg = <0>; + atmel,clk-input-range = <2000000 32000000>; + #atmel,pll-clk-output-range-cells = <4>; + atmel,pll-clk-output-ranges = <74500000 800000000 0 0 + 69500000 750000000 1 0 + 64500000 700000000 2 0 + 59500000 650000000 3 0 + 54500000 600000000 0 1 + 49500000 550000000 1 1 + 44500000 500000000 2 1 + 40000000 450000000 3 1>; + }; + +Required properties for plldiv clocks (plldiv = pll / 2): +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the plla clock phandle. + +The pll divisor is equal to 2 and cannot be changed. + +For example: + plladiv: plladivck { + compatible = "atmel,at91sam9x5-clk-plldiv"; + #clock-cells = <0>; + clocks = <&plla>; + }; + +Required properties for programmable clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- clocks : shall be the programmable clock source phandles. + e.g. clocks = <&clk32k>, <&main>, <&plla>, <&pllb>; +- name: device tree node describing a specific prog clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg : programmable clock id (register offset from PCKx + register). + * interrupts : shall be set to "<(8 + id)>". + +For example: + prog: progck { + compatible = "atmel,at91sam9g45-clk-programmable"; + #size-cells = <0>; + #address-cells = <1>; + interrupt-parent = <&pmc>; + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>; + + prog0 { + #clock-cells = <0>; + reg = <0>; + interrupts = <8>; + }; + + prog1 { + #clock-cells = <0>; + reg = <1>; + interrupts = <9>; + }; + }; + + +Required properties for smd clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the smd clock source phandles. + e.g. clocks = <&plladiv>, <&utmi>; + +For example: + smd: smdck { + compatible = "atmel,at91sam9x5-clk-smd"; + #clock-cells = <0>; + clocks = <&plladiv>, <&utmi>; + }; + +Required properties for system clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- name: device tree node describing a specific system clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg: system clock id (bit position in SCER/SCDR/SCSR registers). + See Atmel's datasheet to get a full list of system clock ids. + +For example: + system: systemck { + compatible = "atmel,at91rm9200-clk-system"; + #address-cells = <1>; + #size-cells = <0>; + + ddrck { + #clock-cells = <0>; + reg = <2>; + clocks = <&mck>; + }; + + uhpck { + #clock-cells = <0>; + reg = <6>; + clocks = <&usb>; + }; + + udpck { + #clock-cells = <0>; + reg = <7>; + clocks = <&usb>; + }; + }; + + +Required properties for usb clock: +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the smd clock source phandles. + e.g. clocks = <&pllb>; +- atmel,clk-divisors (only available for "atmel,at91rm9200-clk-usb"): + usb clock divisor table. + e.g. divisors = <1 2 4 0>; + +For example: + usb: usbck { + compatible = "atmel,at91sam9x5-clk-usb"; + #clock-cells = <0>; + clocks = <&plladiv>, <&utmi>; + }; + + usb: usbck { + compatible = "atmel,at91rm9200-clk-usb"; + #clock-cells = <0>; + clocks = <&pllb>; + atmel,clk-divisors = <1 2 4 0>; + }; + + +Required properties for utmi clock: +- interrupts : shall be set to "<AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>". +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the main clock source phandle. + +For example: + utmi: utmick { + compatible = "atmel,at91sam9x5-clk-utmi"; + interrupt-parent = <&pmc>; + interrupts = <AT91_PMC_LOCKU IRQ_TYPE_LEVEL_HIGH>; + #clock-cells = <0>; + clocks = <&main>; + }; + +Required properties for 32 bits bus Matrix clock (h32mx clock): +- #clock-cells : from common clock binding; shall be set to 0. +- clocks : shall be the master clock source phandle. + +For example: + h32ck: h32mxck { + #clock-cells = <0>; + compatible = "atmel,sama5d4-clk-h32mx"; + clocks = <&mck>; + }; + +Required properties for generated clocks: +- #size-cells : shall be 0 (reg is used to encode clk id). +- #address-cells : shall be 1 (reg is used to encode clk id). +- clocks : shall be the generated clock source phandles. + e.g. clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; +- name: device tree node describing a specific generated clock. + * #clock-cells : from common clock binding; shall be set to 0. + * reg: peripheral id. See Atmel's datasheets to get a full + list of peripheral ids. + * atmel,clk-output-range : minimum and maximum clock frequency + (two u32 fields). + +For example: + gck { + compatible = "atmel,sama5d2-clk-generated"; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clk32k>, <&main>, <&plladiv>, <&utmi>, <&mck>, <&audio_pll_pmc>; + + tcb0_gclk: tcb0_gclk { + #clock-cells = <0>; + reg = <35>; + atmel,clk-output-range = <0 83000000>; + }; + + pwm_gclk: pwm_gclk { + #clock-cells = <0>; + reg = <38>; + atmel,clk-output-range = <0 83000000>; + }; + }; + +Required properties for I2S mux clocks: +- #size-cells : shall be 0 (reg is used to encode I2S bus id). +- #address-cells : shall be 1 (reg is used to encode I2S bus id). +- name: device tree node describing a specific mux clock. + * #clock-cells : from common clock binding; shall be set to 0. + * clocks : shall be the mux clock parent phandles; shall be 2 phandles: + peripheral and generated clock; the first phandle shall belong to the + peripheral clock and the second one shall belong to the generated + clock; "clock-indices" property can be user to specify + the correct order. + * reg: I2S bus id of the corresponding mux clock. + e.g. reg = <0>; for i2s0, reg = <1>; for i2s1 + +For example: + i2s_clkmux { + compatible = "atmel,sama5d2-clk-i2s-mux"; + #address-cells = <1>; + #size-cells = <0>; + + i2s0muxck: i2s0_muxclk { + clocks = <&i2s0_clk>, <&i2s0_gclk>; + #clock-cells = <0>; + reg = <0>; + }; + + i2s1muxck: i2s1_muxclk { + clocks = <&i2s1_clk>, <&i2s1_gclk>; + #clock-cells = <0>; + reg = <1>; + }; + }; |