diff options
Diffstat (limited to 'Documentation/devicetree/bindings/dma/ste-dma40.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/dma/ste-dma40.txt | 138 |
1 files changed, 138 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/dma/ste-dma40.txt b/Documentation/devicetree/bindings/dma/ste-dma40.txt new file mode 100644 index 000000000..99ab5c4d3 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/ste-dma40.txt @@ -0,0 +1,138 @@ +* DMA40 DMA Controller + +Required properties: +- compatible: "stericsson,dma40" +- reg: Address range of the DMAC registers +- reg-names: Names of the above areas to use during resource look-up +- interrupt: Should contain the DMAC interrupt number +- #dma-cells: must be <3> +- memcpy-channels: Channels to be used for memcpy + +Optional properties: +- dma-channels: Number of channels supported by hardware - if not present + the driver will attempt to obtain the information from H/W +- disabled-channels: Channels which can not be used + +Example: + + dma: dma-controller@801c0000 { + compatible = "stericsson,db8500-dma40", "stericsson,dma40"; + reg = <0x801C0000 0x1000 0x40010000 0x800>; + reg-names = "base", "lcpa"; + interrupt-parent = <&intc>; + interrupts = <0 25 0x4>; + + #dma-cells = <2>; + memcpy-channels = <56 57 58 59 60>; + disabled-channels = <12>; + dma-channels = <8>; + }; + +Clients +Required properties: +- dmas: Comma separated list of dma channel requests +- dma-names: Names of the aforementioned requested channels + +Each dmas request consists of 4 cells: + 1. A phandle pointing to the DMA controller + 2. Device signal number, the signal line for single and burst requests + connected from the device to the DMA40 engine + 3. The DMA request line number (only when 'use fixed channel' is set) + 4. A 32bit mask specifying; mode, direction and endianness + [NB: This list will grow] + 0x00000001: Mode: + Logical channel when unset + Physical channel when set + 0x00000002: Direction: + Memory to Device when unset + Device to Memory when set + 0x00000004: Endianness: + Little endian when unset + Big endian when set + 0x00000008: Use fixed channel: + Use automatic channel selection when unset + Use DMA request line number when set + 0x00000010: Set channel as high priority: + Normal priority when unset + High priority when set + +Existing signal numbers for the DB8500 ASIC. Unless specified, the signals are +bidirectional, i.e. the same for RX and TX operations: + +0: SPI controller 0 +1: SD/MMC controller 0 (unused) +2: SD/MMC controller 1 (unused) +3: SD/MMC controller 2 (unused) +4: I2C port 1 +5: I2C port 3 +6: I2C port 2 +7: I2C port 4 +8: Synchronous Serial Port SSP0 +9: Synchronous Serial Port SSP1 +10: Multi-Channel Display Engine MCDE RX +11: UART port 2 +12: UART port 1 +13: UART port 0 +14: Multirate Serial Port MSP2 +15: I2C port 0 +16: USB OTG in/out endpoints 7 & 15 +17: USB OTG in/out endpoints 6 & 14 +18: USB OTG in/out endpoints 5 & 13 +19: USB OTG in/out endpoints 4 & 12 +20: SLIMbus or HSI channel 0 +21: SLIMbus or HSI channel 1 +22: SLIMbus or HSI channel 2 +23: SLIMbus or HSI channel 3 +24: Multimedia DSP SXA0 +25: Multimedia DSP SXA1 +26: Multimedia DSP SXA2 +27: Multimedia DSP SXA3 +28: SD/MM controller 2 +29: SD/MM controller 0 +30: MSP port 1 on DB8500 v1, MSP port 3 on DB8500 v2 +31: MSP port 0 or SLIMbus channel 0 +32: SD/MM controller 1 +33: SPI controller 2 +34: i2c3 RX2 TX2 +35: SPI controller 1 +36: USB OTG in/out endpoints 3 & 11 +37: USB OTG in/out endpoints 2 & 10 +38: USB OTG in/out endpoints 1 & 9 +39: USB OTG in/out endpoints 8 +40: SPI controller 3 +41: SD/MM controller 3 +42: SD/MM controller 4 +43: SD/MM controller 5 +44: Multimedia DSP SXA4 +45: Multimedia DSP SXA5 +46: SLIMbus channel 8 or Multimedia DSP SXA6 +47: SLIMbus channel 9 or Multimedia DSP SXA7 +48: Crypto Accelerator 1 +49: Crypto Accelerator 1 TX or Hash Accelerator 1 TX +50: Hash Accelerator 1 TX +51: memcpy TX (to be used by the DMA driver for memcpy operations) +52: SLIMbus or HSI channel 4 +53: SLIMbus or HSI channel 5 +54: SLIMbus or HSI channel 6 +55: SLIMbus or HSI channel 7 +56: memcpy (to be used by the DMA driver for memcpy operations) +57: memcpy (to be used by the DMA driver for memcpy operations) +58: memcpy (to be used by the DMA driver for memcpy operations) +59: memcpy (to be used by the DMA driver for memcpy operations) +60: memcpy (to be used by the DMA driver for memcpy operations) +61: Crypto Accelerator 0 +62: Crypto Accelerator 0 TX or Hash Accelerator 0 TX +63: Hash Accelerator 0 TX + +Example: + + uart@80120000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x80120000 0x1000>; + interrupts = <0 11 0x4>; + + dmas = <&dma 13 0 0x2>, /* Logical - DevToMem */ + <&dma 13 0 0x0>; /* Logical - MemToDev */ + dma-names = "rx", "rx"; + + }; |