2 files changed, 127 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/eeprom/at24.txt b/Documentation/devicetree/bindings/eeprom/at24.txt
new file mode 100644
index 000000000..f9a7c9842
--- /dev/null
+++ b/Documentation/devicetree/bindings/eeprom/at24.txt
@@ -0,0 +1,85 @@
+EEPROMs (I2C)
+
+Required properties:
+
+  - compatible: Must be a "<manufacturer>,<model>" pair. The following <model>
+                values are supported (assuming "atmel" as manufacturer):
+
+                "atmel,24c00",
+                "atmel,24c01",
+                "atmel,24cs01",
+                "atmel,24c02",
+                "atmel,24cs02",
+                "atmel,24mac402",
+                "atmel,24mac602",
+                "atmel,spd",
+                "atmel,24c04",
+                "atmel,24cs04",
+                "atmel,24c08",
+                "atmel,24cs08",
+                "atmel,24c16",
+                "atmel,24cs16",
+                "atmel,24c32",
+                "atmel,24cs32",
+                "atmel,24c64",
+                "atmel,24cs64",
+                "atmel,24c128",
+                "atmel,24c256",
+                "atmel,24c512",
+                "atmel,24c1024",
+                "atmel,24c2048",
+
+                If <manufacturer> is not "atmel", then a fallback must be used
+                with the same <model> and "atmel" as manufacturer.
+
+                Example:
+                        compatible = "microchip,24c128", "atmel,24c128";
+
+                Supported manufacturers are:
+
+                "catalyst",
+                "microchip",
+                "nxp",
+                "ramtron",
+                "renesas",
+                "rohm",
+                "st",
+
+                Some vendors use different model names for chips which are just
+                variants of the above. Known such exceptions are listed below:
+
+                "nxp,se97b" - the fallback is "atmel,24c02",
+                "renesas,r1ex24002" - the fallback is "atmel,24c02"
+                "renesas,r1ex24128" - the fallback is "atmel,24c128"
+                "rohm,br24t01" - the fallback is "atmel,24c01"
+
+  - reg: The I2C address of the EEPROM.
+
+Optional properties:
+
+  - pagesize: The length of the pagesize for writing. Please consult the
+              manual of your device, that value varies a lot. A wrong value
+              may result in data loss! If not specified, a safety value of
+              '1' is used which will be very slow.
+
+  - read-only: This parameterless property disables writes to the eeprom.
+
+  - size: Total eeprom size in bytes.
+
+  - no-read-rollover: This parameterless property indicates that the
+                      multi-address eeprom does not automatically roll over
+                      reads to the next slave address. Please consult the
+                      manual of your device.
+
+  - wp-gpios: GPIO to which the write-protect pin of the chip is connected.
+
+  - address-width: number of address bits (one of 8, 16).
+
+Example:
+
+eeprom@52 {
+	compatible = "atmel,24c32";
+	reg = <0x52>;
+	pagesize = <32>;
+	wp-gpios = <&gpio1 3 0>;
+};
diff --git a/Documentation/devicetree/bindings/eeprom/at25.txt b/Documentation/devicetree/bindings/eeprom/at25.txt
new file mode 100644
index 000000000..b3bde97dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/eeprom/at25.txt
@@ -0,0 +1,42 @@
+EEPROMs (SPI) compatible with Atmel at25.
+
+Required properties:
+- compatible : Should be "<vendor>,<type>", and generic value "atmel,at25".
+  Example "<vendor>,<type>" values:
+    "microchip,25lc040"
+    "st,m95m02"
+    "st,m95256"
+
+- reg : chip select number
+- spi-max-frequency : max spi frequency to use
+- pagesize : size of the eeprom page
+- size : total eeprom size in bytes
+- address-width : number of address bits (one of 8, 9, 16, or 24).
+  For 9 bits, the MSB of the address is sent as bit 3 of the instruction
+  byte, before the address byte.
+
+Optional properties:
+- spi-cpha : SPI shifted clock phase, as per spi-bus bindings.
+- spi-cpol : SPI inverse clock polarity, as per spi-bus bindings.
+- read-only : this parameter-less property disables writes to the eeprom
+
+Obsolete legacy properties can be used in place of "size", "pagesize",
+"address-width", and "read-only":
+- at25,byte-len : total eeprom size in bytes
+- at25,addr-mode : addr-mode flags, as defined in include/linux/spi/eeprom.h
+- at25,page-size : size of the eeprom page
+
+Additional compatible properties are also allowed.
+
+Example:
+	eeprom@0 {
+		compatible = "st,m95256", "atmel,at25";
+		reg = <0>
+		spi-max-frequency = <5000000>;
+		spi-cpha;
+		spi-cpol;
+
+		pagesize = <64>;
+		size = <32768>;
+		address-width = <16>;
+	};