1 files changed, 95 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
new file mode 100644
index 000000000..38ca2201e
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-mvebu.txt
@@ -0,0 +1,95 @@
+* Marvell EBU GPIO controller
+
+Required properties:
+
+- compatible : Should be "marvell,orion-gpio", "marvell,mv78200-gpio",
+  "marvell,armadaxp-gpio" or "marvell,armada-8k-gpio".
+
+    "marvell,orion-gpio" should be used for Orion, Kirkwood, Dove,
+    Discovery (except MV78200) and Armada 370. "marvell,mv78200-gpio"
+    should be used for the Discovery MV78200.
+
+    "marvel,armadaxp-gpio" should be used for all Armada XP SoCs
+    (MV78230, MV78260, MV78460).
+
+    "marvell,armada-8k-gpio" should be used for the Armada 7K and 8K
+    SoCs (either from AP or CP), see
+    Documentation/devicetree/bindings/arm/marvell/cp110-system-controller0.txt
+    and
+    Documentation/devicetree/bindings/arm/marvell/ap806-system-controller.txt
+    for specific details about the offset property.
+
+- reg: Address and length of the register set for the device. Only one
+  entry is expected, except for the "marvell,armadaxp-gpio" variant
+  for which two entries are expected: one for the general registers,
+  one for the per-cpu registers. Not used for marvell,armada-8k-gpio.
+
+- interrupts: The list of interrupts that are used for all the pins
+  managed by this GPIO bank. There can be more than one interrupt
+  (example: 1 interrupt per 8 pins on Armada XP, which means 4
+  interrupts per bank of 32 GPIOs).
+
+- interrupt-controller: identifies the node as an interrupt controller
+
+- #interrupt-cells: specifies the number of cells needed to encode an
+  interrupt source. Should be two.
+  The first cell is the GPIO number.
+  The second cell is used to specify flags:
+    bits[3:0] trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+- gpio-controller: marks the device node as a gpio controller
+
+- ngpios: number of GPIOs this controller has
+
+- #gpio-cells: Should be two. The first cell is the pin number. The
+  second cell is reserved for flags, unused at the moment.
+
+Optional properties:
+
+In order to use the GPIO lines in PWM mode, some additional optional
+properties are required.
+
+- compatible: Must contain "marvell,armada-370-gpio"
+
+- reg: an additional register set is needed, for the GPIO Blink
+  Counter on/off registers.
+
+- reg-names: Must contain an entry "pwm" corresponding to the
+  additional register range needed for PWM operation.
+
+- #pwm-cells: Should be two. The first cell is the GPIO line number. The
+  second cell is the period in nanoseconds.
+
+- clocks: Must be a phandle to the clock for the GPIO controller.
+
+Example:
+
+		gpio0: gpio@d0018100 {
+			compatible = "marvell,armadaxp-gpio";
+			reg = <0xd0018100 0x40>,
+			    <0xd0018800 0x30>;
+			ngpios = <32>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <16>, <17>, <18>, <19>;
+		};
+
+		gpio1: gpio@18140 {
+			compatible = "marvell,armada-370-gpio";
+			reg = <0x18140 0x40>, <0x181c8 0x08>;
+			reg-names = "gpio", "pwm";
+			ngpios = <17>;
+			gpio-controller;
+			#gpio-cells = <2>;
+			#pwm-cells = <2>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+			interrupts = <87>, <88>, <89>;
+			clocks = <&coreclk 0>;
+		};