diff options
Diffstat (limited to 'Documentation/devicetree/bindings/iio/temperature')
5 files changed, 125 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt new file mode 100644 index 000000000..28bc5c4d9 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/maxim_thermocouple.txt @@ -0,0 +1,21 @@ +Maxim thermocouple support + +* https://datasheets.maximintegrated.com/en/ds/MAX6675.pdf +* https://datasheets.maximintegrated.com/en/ds/MAX31855.pdf + +Required properties: + + - compatible: must be "maxim,max31855" or "maxim,max6675" + - reg: SPI chip select number for the device + - spi-max-frequency: must be 4300000 + - spi-cpha: must be defined for max6675 to enable SPI mode 1 + + Refer to spi/spi-bus.txt for generic SPI slave bindings. + +Example: + + max31855@0 { + compatible = "maxim,max31855"; + reg = <0>; + spi-max-frequency = <4300000>; + }; diff --git a/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt b/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt new file mode 100644 index 000000000..9be57b036 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/mlx90614.txt @@ -0,0 +1,24 @@ +* Melexis MLX90614 contactless IR temperature sensor + +http://melexis.com/Infrared-Thermometer-Sensors/Infrared-Thermometer-Sensors/MLX90614-615.aspx + +Required properties: + + - compatible: should be "melexis,mlx90614" + - reg: the I2C address of the sensor + +Optional properties: + + - wakeup-gpios: device tree identifier of the GPIO connected to the SDA line + to hold low in order to wake up the device. In normal operation, the + GPIO is set as input and will not interfere in I2C communication. There + is no need for a GPIO driving the SCL line. If no GPIO is given, power + management is disabled. + +Example: + +mlx90614@5a { + compatible = "melexis,mlx90614"; + reg = <0x5a>; + wakeup-gpios = <&gpio0 2 GPIO_ACTIVE_HIGH>; +}; diff --git a/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt b/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt new file mode 100644 index 000000000..0b0581200 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/mlx90632.txt @@ -0,0 +1,28 @@ +* Melexis MLX90632 contactless Infra Red temperature sensor + +Link to datasheet: https://www.melexis.com/en/documents/documentation/datasheets/datasheet-mlx90632 + +There are various applications for the Infra Red contactless temperature sensor +and MLX90632 is most suitable for consumer applications where measured object +temperature is in range between -20 to 200 degrees Celsius with relative error +of measurement below 1 degree Celsius in object temperature range for +industrial applications. Since it can operate and measure ambient temperature +in range of -20 to 85 degrees Celsius it is suitable also for outdoor use. + +Be aware that electronics surrounding the sensor can increase ambient +temperature. MLX90632 can be calibrated to reduce the housing effect via +already existing EEPROM parameters. + +Since measured object emissivity effects Infra Red energy emitted, emissivity +should be set before requesting the object temperature. + +Required properties: + - compatible: should be "melexis,mlx90632" + - reg: the I2C address of the sensor (default 0x3a) + +Example: + +mlx90632@3a { + compatible = "melexis,mlx90632"; + reg = <0x3a>; +}; diff --git a/Documentation/devicetree/bindings/iio/temperature/tmp007.txt b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt new file mode 100644 index 000000000..da0af234a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/tmp007.txt @@ -0,0 +1,33 @@ +* TI TMP007 - IR thermopile sensor with integrated math engine + +Link to datasheet: http://www.ti.com/lit/ds/symlink/tmp007.pdf + +Required properties: + + - compatible: should be "ti,tmp007" + - reg: the I2C address of the sensor (changeable via ADR pins) + ------------------------------ + |ADR1 | ADR0 | Device Address| + ------------------------------ + 0 0 0x40 + 0 1 0x41 + 0 SDA 0x42 + 0 SCL 0x43 + 1 0 0x44 + 1 1 0x45 + 1 SDA 0x46 + 1 SCL 0x47 + +Optional properties: + + - interrupts: interrupt mapping for GPIO IRQ (level active low) + +Example: + +tmp007@40 { + compatible = "ti,tmp007"; + reg = <0x40>; + interrupt-parent = <&gpio0>; + interrupts = <5 0x08>; +}; + diff --git a/Documentation/devicetree/bindings/iio/temperature/tsys01.txt b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt new file mode 100644 index 000000000..0d5cc5595 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/temperature/tsys01.txt @@ -0,0 +1,19 @@ +* TSYS01 - Measurement Specialties temperature sensor + +Required properties: + + - compatible: should be "meas,tsys01" + - reg: I2C address of the sensor (changeable via CSB pin) + + ------------------------ + | CSB | Device Address | + ------------------------ + 1 0x76 + 0 0x77 + +Example: + +tsys01@76 { + compatible = "meas,tsys01"; + reg = <0x76>; +}; |