diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mfd/axp20x.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/mfd/axp20x.txt | 262 |
1 files changed, 262 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mfd/axp20x.txt b/Documentation/devicetree/bindings/mfd/axp20x.txt new file mode 100644 index 000000000..188f0373d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/axp20x.txt @@ -0,0 +1,262 @@ +AXP family PMIC device tree bindings + +The axp20x family current members : +axp152 (X-Powers) +axp202 (X-Powers) +axp209 (X-Powers) +axp221 (X-Powers) +axp223 (X-Powers) +axp803 (X-Powers) +axp806 (X-Powers) +axp809 (X-Powers) +axp813 (X-Powers) + +The AXP813 is 2 chips packaged into 1. The 2 chips do not share anything +other than the packaging. Pins are routed separately. As such they should +be treated as separate entities. The other half is an AC100 RTC/codec +combo chip. Please see ./ac100.txt for its bindings. + +Required properties: +- compatible: should be one of: + * "x-powers,axp152" + * "x-powers,axp202" + * "x-powers,axp209" + * "x-powers,axp221" + * "x-powers,axp223" + * "x-powers,axp803" + * "x-powers,axp806" + * "x-powers,axp809" + * "x-powers,axp813" +- reg: The I2C slave address or RSB hardware address for the AXP chip +- interrupts: SoC NMI / GPIO interrupt connected to the PMIC's IRQ pin +- interrupt-controller: The PMIC has its own internal IRQs +- #interrupt-cells: Should be set to 1 + +Optional properties: +- x-powers,dcdc-freq: defines the work frequency of DC-DC in KHz + AXP152/20X: range: 750-1875, Default: 1.5 MHz + AXP22X/8XX: range: 1800-4050, Default: 3 MHz + +- x-powers,drive-vbus-en: boolean, set this when the N_VBUSEN pin is + used as an output pin to control an external + regulator to drive the OTG VBus, rather then + as an input pin which signals whether the + board is driving OTG VBus or not. + (axp221 / axp223 / axp803/ axp813 only) + +- x-powers,self-working-mode and + x-powers,master-mode: Boolean (axp806 only). Set either of these when the + PMIC is wired for self-working mode or master mode. + If neither is set then slave mode is assumed. + This corresponds to how the MODESET pin is wired. + +- <input>-supply: a phandle to the regulator supply node. May be omitted if + inputs are unregulated, such as using the IPSOUT output + from the PMIC. + +- regulators: A node that houses a sub-node for each regulator. Regulators + not used but preferred to be managed by the OS should be + listed as well. + See Documentation/devicetree/bindings/regulator/regulator.txt + for more information on standard regulator bindings. + +Optional properties for DCDC regulators: +- x-powers,dcdc-workmode: 1 for PWM mode, 0 for AUTO (PWM/PFM) mode + Default: Current hardware setting + The DCDC regulators work in a mixed PWM/PFM mode, + using PFM under light loads and switching to PWM + for heavier loads. Forcing PWM mode trades efficiency + under light loads for lower output noise. This + probably makes sense for HiFi audio related + applications that aren't battery constrained. + +AXP202/AXP209 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +LDO1 : LDO : acin-supply : always on +LDO2 : LDO : ldo24in-supply : shared supply +LDO3 : LDO : ldo3in-supply +LDO4 : LDO : ldo24in-supply : shared supply +LDO5 : LDO : ldo5in-supply + +AXP221/AXP223 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + +AXP803 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply : poly-phase capable +DCDC3 : DC-DC buck : vin3-supply : poly-phase capable +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply : poly-phase capable +DCDC6 : DC-DC buck : vin6-supply : poly-phase capable +DC1SW : On/Off Switch : : DCDC1 secondary output +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +FLDO1 : LDO : fldoin-supply : shared supply +FLDO2 : LDO : fldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + +AXP806 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDCA : DC-DC buck : vina-supply : poly-phase capable +DCDCB : DC-DC buck : vinb-supply : poly-phase capable +DCDCC : DC-DC buck : vinc-supply : poly-phase capable +DCDCD : DC-DC buck : vind-supply : poly-phase capable +DCDCE : DC-DC buck : vine-supply : poly-phase capable +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +BLDO1 : LDO : bldoin-supply : shared supply +BLDO2 : LDO : bldoin-supply : shared supply +BLDO3 : LDO : bldoin-supply : shared supply +BLDO4 : LDO : bldoin-supply : shared supply +CLDO1 : LDO : cldoin-supply : shared supply +CLDO2 : LDO : cldoin-supply : shared supply +CLDO3 : LDO : cldoin-supply : shared supply +SW : On/Off Switch : swin-supply + +Additionally, the AXP806 DC-DC regulators support poly-phase arrangements +for higher output current. The possible groupings are: A+B, A+B+C, D+E. + +AXP809 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply +DCDC3 : DC-DC buck : vin3-supply +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply +DC1SW : On/Off Switch : : DCDC1 secondary output +DC5LDO : LDO : : input from DCDC5 +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +SW : On/Off Switch : swin-supply + +AXP813 regulators, type, and corresponding input supply names: + +Regulator Type Supply Name Notes +--------- ---- ----------- ----- +DCDC1 : DC-DC buck : vin1-supply +DCDC2 : DC-DC buck : vin2-supply : poly-phase capable +DCDC3 : DC-DC buck : vin3-supply : poly-phase capable +DCDC4 : DC-DC buck : vin4-supply +DCDC5 : DC-DC buck : vin5-supply : poly-phase capable +DCDC6 : DC-DC buck : vin6-supply : poly-phase capable +DCDC7 : DC-DC buck : vin7-supply +ALDO1 : LDO : aldoin-supply : shared supply +ALDO2 : LDO : aldoin-supply : shared supply +ALDO3 : LDO : aldoin-supply : shared supply +DLDO1 : LDO : dldoin-supply : shared supply +DLDO2 : LDO : dldoin-supply : shared supply +DLDO3 : LDO : dldoin-supply : shared supply +DLDO4 : LDO : dldoin-supply : shared supply +ELDO1 : LDO : eldoin-supply : shared supply +ELDO2 : LDO : eldoin-supply : shared supply +ELDO3 : LDO : eldoin-supply : shared supply +FLDO1 : LDO : fldoin-supply : shared supply +FLDO2 : LDO : fldoin-supply : shared supply +FLDO3 : LDO : fldoin-supply : shared supply +LDO_IO0 : LDO : ips-supply : GPIO 0 +LDO_IO1 : LDO : ips-supply : GPIO 1 +RTC_LDO : LDO : ips-supply : always on +SW : On/Off Switch : swin-supply +DRIVEVBUS : Enable output : drivevbus-supply : external regulator + +Example: + +axp209: pmic@34 { + compatible = "x-powers,axp209"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + regulators { + x-powers,dcdc-freq = <1500>; + + vdd_cpu: dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; + }; + + vdd_int_dll: dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; + }; + + vdd_rtc: ldo1 { + regulator-always-on; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-rtc"; + }; + + avcc: ldo2 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; + }; + + ldo3 { + /* unused but preferred to be managed by OS */ + }; + }; +}; |