1 files changed, 138 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
new file mode 100644
index 000000000..1123cc6d5
--- /dev/null
+++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt
@@ -0,0 +1,138 @@
+* Qualcomm NAND controller
+
+Required properties:
+- compatible:		must be one of the following:
+    * "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
+			    SoC and it uses ADM DMA
+    * "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
+                            IPQ4019 SoC and it uses BAM DMA
+    * "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in
+                            IPQ8074 SoC and it uses BAM DMA
+
+- reg:			MMIO address range
+- clocks:		must contain core clock and always on clock
+- clock-names:		must contain "core" for the core clock and "aon" for the
+			always on clock
+
+EBI2 specific properties:
+- dmas:			DMA specifier, consisting of a phandle to the ADM DMA
+			controller node and the channel number to be used for
+			NAND. Refer to dma.txt and qcom_adm.txt for more details
+- dma-names:		must be "rxtx"
+- qcom,cmd-crci:	must contain the ADM command type CRCI block instance
+			number specified for the NAND controller on the given
+			platform
+- qcom,data-crci:	must contain the ADM data type CRCI block instance
+			number specified for the NAND controller on the given
+			platform
+
+QPIC specific properties:
+- dmas:			DMA specifier, consisting of a phandle to the BAM DMA
+			and the channel number to be used for NAND. Refer to
+			dma.txt, qcom_bam_dma.txt for more details
+- dma-names:		must contain all 3 channel names : "tx", "rx", "cmd"
+- #address-cells:	<1> - subnodes give the chip-select number
+- #size-cells:		<0>
+
+* NAND chip-select
+
+Each controller may contain one or more subnodes to represent enabled
+chip-selects which (may) contain NAND flash chips. Their properties are as
+follows.
+
+Required properties:
+- reg:			a single integer representing the chip-select
+			number (e.g., 0, 1, 2, etc.)
+- #address-cells:	see partition.txt
+- #size-cells:		see partition.txt
+
+Optional properties:
+- nand-bus-width:	see nand.txt
+- nand-ecc-strength:	see nand.txt. If not specified, then ECC strength will
+			be used according to chip requirement and available
+			OOB size.
+
+Each nandcs device node may optionally contain a 'partitions' sub-node, which
+further contains sub-nodes describing the flash partition mapping. See
+partition.txt for more detail.
+
+Example:
+
+nand-controller@1ac00000 {
+	compatible = "qcom,ipq806x-nand";
+	reg = <0x1ac00000 0x800>;
+
+	clocks = <&gcc EBI2_CLK>,
+		 <&gcc EBI2_AON_CLK>;
+	clock-names = "core", "aon";
+
+	dmas = <&adm_dma 3>;
+	dma-names = "rxtx";
+	qcom,cmd-crci = <15>;
+	qcom,data-crci = <3>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	nand@0 {
+		reg = <0>;
+
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot-nand";
+				reg = <0 0x58a0000>;
+			};
+
+			partition@58a0000 {
+				label = "fs-nand";
+				reg = <0x58a0000 0x4000000>;
+			};
+		};
+	};
+};
+
+nand-controller@79b0000 {
+	compatible = "qcom,ipq4019-nand";
+	reg = <0x79b0000 0x1000>;
+
+	clocks = <&gcc GCC_QPIC_CLK>,
+		<&gcc GCC_QPIC_AHB_CLK>;
+	clock-names = "core", "aon";
+
+	dmas = <&qpicbam 0>,
+		<&qpicbam 1>,
+		<&qpicbam 2>;
+	dma-names = "tx", "rx", "cmd";
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	nand@0 {
+		reg = <0>;
+		nand-ecc-strength = <4>;
+		nand-bus-width = <8>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "boot-nand";
+				reg = <0 0x58a0000>;
+			};
+
+			partition@58a0000 {
+				label = "fs-nand";
+				reg = <0x58a0000 0x4000000>;
+			};
+		};
+	};
+};