diff options
Diffstat (limited to 'Documentation/devicetree/bindings/net/nfc')
10 files changed, 403 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt new file mode 100644 index 000000000..c9b35251b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/nfcmrvl.txt @@ -0,0 +1,84 @@ +* Marvell International Ltd. NCI NFC Controller + +Required properties: +- compatible: Should be: + - "marvell,nfc-uart" or "mrvl,nfc-uart" for UART devices + - "marvell,nfc-i2c" for I2C devices + - "marvell,nfc-spi" for SPI devices + +Optional SoC specific properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- reset-n-io: Output GPIO pin used to reset the chip (active low). +- hci-muxed: Specifies that the chip is muxing NCI over HCI frames. + +Optional UART-based chip specific properties: +- flow-control: Specifies that the chip is using RTS/CTS. +- break-control: Specifies that the chip needs specific break management. + +Optional I2C-based chip specific properties: +- i2c-int-falling: Specifies that the chip read event shall be trigged on + falling edge. +- i2c-int-rising: Specifies that the chip read event shall be trigged on + rising edge. + +Example (for ARM-based BeagleBoard Black with 88W8887 on UART5): + +&uart5 { + + nfcmrvluart: nfcmrvluart@5 { + compatible = "marvell,nfc-uart"; + + reset-n-io = <&gpio3 16 0>; + + hci-muxed; + flow-control; + } +}; + + +Example (for ARM-based BeagleBoard Black with 88W8887 on I2C1): + +&i2c1 { + clock-frequency = <400000>; + + nfcmrvli2c0: i2c@1 { + compatible = "marvell,nfc-i2c"; + + reg = <0x8>; + + /* I2C INT configuration */ + interrupt-parent = <&gpio3>; + interrupts = <21 0>; + + /* I2C INT trigger configuration */ + i2c-int-rising; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; + + +Example (for ARM-based BeagleBoard Black on SPI0): + +&spi0 { + + mrvlnfcspi0: spi@0 { + compatible = "marvell,nfc-spi"; + + reg = <0>; + + /* SPI Bus configuration */ + spi-max-frequency = <3000000>; + spi-cpha; + spi-cpol; + + /* SPI INT configuration */ + interrupt-parent = <&gpio1>; + interrupts = <17 0>; + + /* Reset IO */ + reset-n-io = <&gpio3 19 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt new file mode 100644 index 000000000..9e4dc510a --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/nxp-nci.txt @@ -0,0 +1,33 @@ +* NXP Semiconductors NXP NCI NFC Controllers + +Required properties: +- compatible: Should be "nxp,nxp-nci-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the chip +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with NPC100 NFC controller on I2C2): + +&i2c2 { + + + npc100: npc100@29 { + + compatible = "nxp,nxp-nci-i2c"; + + reg = <0x29>; + clock-frequency = <100000>; + + interrupt-parent = <&gpio1>; + interrupts = <29 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&gpio0 30 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt new file mode 100644 index 000000000..2efe3886b --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn533-i2c.txt @@ -0,0 +1,29 @@ +* NXP Semiconductors PN532 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn532-i2c" or "nxp,pn533-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN532 on I2C2): + +&i2c2 { + + + pn532: pn532@24 { + + compatible = "nxp,pn532-i2c"; + + reg = <0x24>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/pn544.txt b/Documentation/devicetree/bindings/net/nfc/pn544.txt new file mode 100644 index 000000000..2bd82562c --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/pn544.txt @@ -0,0 +1,33 @@ +* NXP Semiconductors PN544 NFC Controller + +Required properties: +- compatible: Should be "nxp,pn544-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- enable-gpios: Output GPIO pin used for enabling/disabling the PN544 +- firmware-gpios: Output GPIO pin used to enter firmware download mode + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. + +Example (for ARM-based BeagleBone with PN544 on I2C2): + +&i2c2 { + + + pn544: pn544@28 { + + compatible = "nxp,pn544-i2c"; + + reg = <0x28>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio1>; + interrupts = <17 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH>; + firmware-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt new file mode 100644 index 000000000..f02f6fb7f --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/s3fwrn5.txt @@ -0,0 +1,25 @@ +* Samsung S3FWRN5 NCI NFC Controller + +Required properties: +- compatible: Should be "samsung,s3fwrn5-i2c". +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- s3fwrn5,en-gpios: Output GPIO pin used for enabling/disabling the chip +- s3fwrn5,fw-gpios: Output GPIO pin used to enter firmware mode and + sleep/wakeup control + +Example: + +&hsi2c_4 { + s3fwrn5@27 { + compatible = "samsung,s3fwrn5-i2c"; + + reg = <0x27>; + + interrupt-parent = <&gpa1>; + interrupts = <3 0 0>; + + s3fwrn5,en-gpios = <&gpf1 4 0>; + s3fwrn5,fw-gpios = <&gpj0 2 0>; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt new file mode 100644 index 000000000..baa8f8133 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-i2c.txt @@ -0,0 +1,38 @@ +* STMicroelectronics SAS. ST NCI NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb-i2c" or "st,st21nfcc-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on I2C2): + +&i2c2 { + + + st21nfcb: st21nfcb@8 { + + compatible = "st,st21nfcb-i2c"; + + reg = <0x08>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt new file mode 100644 index 000000000..d33343330 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st-nci-spi.txt @@ -0,0 +1,36 @@ +* STMicroelectronics SAS. ST NCI NFC Controller + +Required properties: +- compatible: Should be "st,st21nfcb-spi" +- spi-max-frequency: Maximum SPI frequency (<= 4000000). +- interrupts: GPIO interrupt to which the chip is connected +- reset-gpios: Output GPIO pin used to reset the ST21NFCB + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCB on SPI4): + +&mcspi4 { + + + st21nfcb: st21nfcb@0 { + + compatible = "st,st21nfcb-spi"; + + clock-frequency = <4000000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_EDGE_RISING>; + + reset-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st21nfca.txt b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt new file mode 100644 index 000000000..b8bd90f80 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st21nfca.txt @@ -0,0 +1,37 @@ +* STMicroelectronics SAS. ST21NFCA NFC Controller + +Required properties: +- compatible: Should be "st,st21nfca-i2c". +- clock-frequency: I²C work frequency. +- reg: address on the bus +- enable-gpios: Output GPIO pin used for enabling/disabling the ST21NFCA + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- ese-present: Specifies that an ese is physically connected to the nfc +controller. +- uicc-present: Specifies that the uicc swp signal can be physically +connected to the nfc controller. + +Example (for ARM-based BeagleBoard xM with ST21NFCA on I2C2): + +&i2c2 { + + + st21nfca: st21nfca@1 { + + compatible = "st,st21nfca-i2c"; + + reg = <0x01>; + clock-frequency = <400000>; + + interrupt-parent = <&gpio5>; + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; + + enable-gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + + ese-present; + uicc-present; + }; +}; diff --git a/Documentation/devicetree/bindings/net/nfc/st95hf.txt b/Documentation/devicetree/bindings/net/nfc/st95hf.txt new file mode 100644 index 000000000..3f373a1e2 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/st95hf.txt @@ -0,0 +1,45 @@ +* STMicroelectronics : NFC Transceiver ST95HF + +ST NFC Transceiver is required to attach with SPI bus. +ST95HF node should be defined in DT as SPI slave device of SPI +master with which ST95HF transceiver is physically connected. +The properties defined below are required to be the part of DT +to include ST95HF transceiver into the platform. + +Required properties: +=================== +- reg: Address of SPI slave "ST95HF transceiver" on SPI master bus. + +- compatible: should be "st,st95hf" for ST95HF NFC transceiver + +- spi-max-frequency: Max. operating SPI frequency for ST95HF + transceiver. + +- enable-gpio: GPIO line to enable ST95HF transceiver. + +- interrupts : Standard way to define ST95HF transceiver's out + interrupt. + +Optional property: +================= +- st95hfvin-supply : This is an optional property. It contains a + phandle to ST95HF transceiver's regulator supply node in DT. + +Example: +======= +spi@9840000 { + reg = <0x9840000 0x110>; + #address-cells = <1>; + #size-cells = <0>; + cs-gpios = <&pio0 4>; + + st95hf@0{ + reg = <0>; + compatible = "st,st95hf"; + spi-max-frequency = <1000000>; + enable-gpio = <&pio4 0>; + interrupt-parent = <&pio0>; + interrupts = <7 IRQ_TYPE_EDGE_FALLING>; + }; + +}; diff --git a/Documentation/devicetree/bindings/net/nfc/trf7970a.txt b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt new file mode 100644 index 000000000..ba1934b95 --- /dev/null +++ b/Documentation/devicetree/bindings/net/nfc/trf7970a.txt @@ -0,0 +1,43 @@ +* Texas Instruments TRF7970A RFID/NFC/15693 Transceiver + +Required properties: +- compatible: Should be "ti,trf7970a". +- spi-max-frequency: Maximum SPI frequency (<= 2000000). +- interrupts: A single interrupt specifier. +- ti,enable-gpios: One or two GPIO entries used for 'EN' and 'EN2' pins on the + TRF7970A. EN2 is optional. +- vin-supply: Regulator for supply voltage to VIN pin + +Optional SoC Specific Properties: +- pinctrl-names: Contains only one value - "default". +- pintctrl-0: Specifies the pin control groups used for this controller. +- autosuspend-delay: Specify autosuspend delay in milliseconds. +- irq-status-read-quirk: Specify that the trf7970a being used has the + "IRQ Status Read" erratum. +- en2-rf-quirk: Specify that the trf7970a being used has the "EN2 RF" + erratum. +- vdd-io-supply: Regulator specifying voltage for vdd-io +- clock-frequency: Set to specify that the input frequency to the trf7970a is 13560000Hz or 27120000Hz + +Example (for ARM-based BeagleBone with TRF7970A on SPI1): + +&spi1 { + + nfc@0 { + compatible = "ti,trf7970a"; + reg = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&trf7970a_default>; + spi-max-frequency = <2000000>; + interrupt-parent = <&gpio2>; + interrupts = <14 0>; + ti,enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>, + <&gpio2 5 GPIO_ACTIVE_HIGH>; + vin-supply = <&ldo3_reg>; + vdd-io-supply = <&ldo2_reg>; + autosuspend-delay = <30000>; + irq-status-read-quirk; + en2-rf-quirk; + clock-frequency = <27120000>; + }; +}; |