diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/net/sff,sfp.txt | 85 |
1 files changed, 85 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/sff,sfp.txt b/Documentation/devicetree/bindings/net/sff,sfp.txt new file mode 100644 index 000000000..832139919 --- /dev/null +++ b/Documentation/devicetree/bindings/net/sff,sfp.txt @@ -0,0 +1,85 @@ +Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP) +Transceiver + +Required properties: + +- compatible : must be one of + "sff,sfp" for SFP modules + "sff,sff" for soldered down SFF modules + +- i2c-bus : phandle of an I2C bus controller for the SFP two wire serial + interface + +Optional Properties: + +- mod-def0-gpios : GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) + module presence input gpio signal, active (module absent) high. Must + not be present for SFF modules + +- los-gpios : GPIO phandle and a specifier of the Receiver Loss of Signal + Indication input gpio signal, active (signal lost) high + +- tx-fault-gpios : GPIO phandle and a specifier of the Module Transmitter + Fault input gpio signal, active (fault condition) high + +- tx-disable-gpios : GPIO phandle and a specifier of the Transmitter Disable + output gpio signal, active (Tx disable) high + +- rate-select0-gpios : GPIO phandle and a specifier of the Rx Signaling Rate + Select (AKA RS0) output gpio signal, low: low Rx rate, high: high Rx rate + Must not be present for SFF modules + +- rate-select1-gpios : GPIO phandle and a specifier of the Tx Signaling Rate + Select (AKA RS1) output gpio signal (SFP+ only), low: low Tx rate, high: + high Tx rate. Must not be present for SFF modules + +- maximum-power-milliwatt : Maximum module power consumption + Specifies the maximum power consumption allowable by a module in the + slot, in milli-Watts. Presently, modules can be up to 1W, 1.5W or 2W. + +Example #1: Direct serdes to SFP connection + +sfp_eth3: sfp-eth3 { + compatible = "sff,sfp"; + i2c-bus = <&sfp_1g_i2c>; + los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>; + maximum-power-milliwatt = <1000>; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>; + tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>; +}; + +&cps_emac3 { + phy-names = "comphy"; + phys = <&cps_comphy5 0>; + sfp = <&sfp_eth3>; +}; + +Example #2: Serdes to PHY to SFP connection + +sfp_eth0: sfp-eth0 { + compatible = "sff,sfp"; + i2c-bus = <&sfpp0_i2c>; + los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&cps_sfpp0_pins>; + tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>; + tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>; +}; + +p0_phy: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c45"; + pinctrl-names = "default"; + pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>; + reg = <0>; + interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>; + sfp = <&sfp_eth0>; +}; + +&cpm_eth0 { + phy = <&p0_phy>; + phy-mode = "10gbase-kr"; +}; |