diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy/ti-phy.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/phy/ti-phy.txt | 134 |
1 files changed, 134 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt new file mode 100644 index 000000000..57dfda8a7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -0,0 +1,134 @@ +TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs + +OMAP CONTROL PHY + +Required properties: + - compatible: Should be one of + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register + e.g. USB2_PHY on OMAP5. + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control + e.g. USB3 PHY and SATA PHY on OMAP5. + "ti,control-phy-pcie" - for pcie to support external clock for pcie and to + set PCS delay value. + e.g. PCIE PHY in DRA7x + "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on + DRA7 platform. + "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on + AM437 platform. + - reg : register ranges as listed in the reg-names property + - reg-names: "otghs_control" for control-phy-otghs + "power", "pcie_pcs" and "control_sma" for control-phy-pcie + "power" for all other types + +omap_control_usb: omap-control-usb@4a002300 { + compatible = "ti,control-phy-otghs"; + reg = <0x4a00233c 0x4>; + reg-names = "otghs_control"; +}; + +OMAP USB2 PHY + +Required properties: + - compatible: Should be "ti,omap-usb2" + Should be "ti,dra7x-usb2" for the 1st instance of USB2 PHY on + DRA7x + Should be "ti,dra7x-usb2-phy2" for the 2nd instance of USB2 PHY + in DRA7x + - reg : Address and length of the register set for the device. + - #phy-cells: determine the number of cells that should be given in the + phandle while referencing this phy. + - clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + - clock-names: should include: + * "wkupclk" - wakeup clock. + * "refclk" - reference clock (optional). + +Deprecated properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +Recommended properies: +- syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. + +This is usually a subnode of ocp2scp to which it is connected. + +usb2phy@4a0ad080 { + compatible = "ti,omap-usb2"; + reg = <0x4a0ad080 0x58>; + ctrl-module = <&omap_control_usb>; + #phy-cells = <0>; + clocks = <&usb_phy_cm_clk32k>, <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", "refclk"; +}; + +TI PIPE3 PHY + +Required properties: + - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or + "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated. + - reg : Address and length of the register set for the device. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + - #phy-cells: determine the number of cells that should be given in the + phandle while referencing this phy. + - clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + - clock-names: should include: + * "wkupclk" - wakeup clock. + * "sysclk" - system clock. + * "refclk" - reference clock. + * "dpll_ref" - external dpll ref clk + * "dpll_ref_m2" - external dpll ref clk + * "phy-div" - divider for apll + * "div-clk" - apll clock + +Optional properties: + - id: If there are multiple instance of the same type, in order to + differentiate between each instance "id" can be used (e.g., multi-lane PCIe + PHY). If "id" is not provided, it is set to default value of '1'. + - syscon-pllreset: Handle to system control region that contains the + CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 + register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. + - syscon-pcs : phandle/offset pair. Phandle to the system control module and the + register offset to write the PCS delay value. + +Deprecated properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +Recommended properies: + - syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. + +This is usually a subnode of ocp2scp to which it is connected. + +usb3phy@4a084400 { + compatible = "ti,phy-usb3"; + reg = <0x4a084400 0x80>, + <0x4a084800 0x64>, + <0x4a084c00 0x40>; + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_usb>; + #phy-cells = <0>; + clocks = <&usb_phy_cm_clk32k>, + <&sys_clkin>, + <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", + "sysclk", + "refclk"; +}; + +sata_phy: phy@4a096000 { + compatible = "ti,phy-pipe3-sata"; + reg = <0x4A096000 0x80>, /* phy_rx */ + <0x4A096400 0x64>, /* phy_tx */ + <0x4A096800 0x40>; /* pll_ctrl */ + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_sata>; + clocks = <&sys_clkin1>, <&sata_ref_clk>; + clock-names = "sysclk", "refclk"; + syscon-pllreset = <&scm_conf 0x3fc>; + #phy-cells = <0>; +}; |