diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt | 217 |
1 files changed, 217 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt new file mode 100644 index 000000000..a72dc3178 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/img,pistachio-pinctrl.txt @@ -0,0 +1,217 @@ +Imagination Technologies Pistachio SoC pin controllers +====================================================== + +The pin controllers on Pistachio are a combined GPIO controller, (GPIO) +interrupt controller, and pinmux + pinconf device. The system ("east") pin +controller on Pistachio has 99 pins, 90 of which are MFIOs which can be +configured as GPIOs. The 90 GPIOs are divided into 6 banks of up to 16 GPIOs +each. The GPIO banks are represented as sub-nodes of the pad controller node. + +Please refer to pinctrl-bindings.txt, ../gpio/gpio.txt, and +../interrupt-controller/interrupts.txt for generic information regarding +pin controller, GPIO, and interrupt bindings. + +Required properties for pin controller node: +-------------------------------------------- + - compatible: "img,pistachio-system-pinctrl". + - reg: Address range of the pinctrl registers. + +Required properties for GPIO bank sub-nodes: +-------------------------------------------- + - interrupts: Interrupt line for the GPIO bank. + - gpio-controller: Indicates the device is a GPIO controller. + - #gpio-cells: Must be two. The first cell is the GPIO pin number and the + second cell indicates the polarity. See <dt-bindings/gpio/gpio.h> for + a list of possible values. + - interrupt-controller: Indicates the device is an interrupt controller. + - #interrupt-cells: Must be two. The first cell is the GPIO pin number and + the second cell encodes the interrupt flags. See + <dt-bindings/interrupt-controller/irq.h> for a list of valid flags. + +Note that the N GPIO bank sub-nodes *must* be named gpio0, gpio1, ... gpioN-1. + +Required properties for pin configuration sub-nodes: +---------------------------------------------------- + - pins: List of pins to which the configuration applies. See below for a + list of possible pins. + +Optional properties for pin configuration sub-nodes: +---------------------------------------------------- + - function: Mux function for the specified pins. This is not applicable for + non-MFIO pins. See below for a list of valid functions for each pin. + - bias-high-impedance: Enable high-impedance mode. + - bias-pull-up: Enable weak pull-up. + - bias-pull-down: Enable weak pull-down. + - bias-bus-hold: Enable bus-keeper mode. + - drive-strength: Drive strength in mA. Supported values: 2, 4, 8, 12. + - input-schmitt-enable: Enable Schmitt trigger. + - input-schmitt-disable: Disable Schmitt trigger. + - slew-rate: Slew rate control. 0 for slow, 1 for fast. + +Pin Functions +--- --------- +mfio0 spim1 +mfio1 spim1, spim0, uart1 +mfio2 spim1, spim0, uart1 +mfio3 spim1 +mfio4 spim1 +mfio5 spim1 +mfio6 spim1 +mfio7 spim1 +mfio8 spim0 +mfio9 spim0 +mfio10 spim0 +mfio11 spis +mfio12 spis +mfio13 spis +mfio14 spis +mfio15 sdhost, mips_trace_clk, mips_trace_data +mfio16 sdhost, mips_trace_dint, mips_trace_data +mfio17 sdhost, mips_trace_trigout, mips_trace_data +mfio18 sdhost, mips_trace_trigin, mips_trace_data +mfio19 sdhost, mips_trace_dm, mips_trace_data +mfio20 sdhost, mips_trace_probe_n, mips_trace_data +mfio21 sdhost, mips_trace_data +mfio22 sdhost, mips_trace_data +mfio23 sdhost +mfio24 sdhost +mfio25 sdhost +mfio26 sdhost +mfio27 sdhost +mfio28 i2c0, spim0 +mfio29 i2c0, spim0 +mfio30 i2c1, spim0 +mfio31 i2c1, spim1 +mfio32 i2c2 +mfio33 i2c2 +mfio34 i2c3 +mfio35 i2c3 +mfio36 i2s_out, audio_clk_in +mfio37 i2s_out, debug_raw_cca_ind +mfio38 i2s_out, debug_ed_sec20_cca_ind +mfio39 i2s_out, debug_ed_sec40_cca_ind +mfio40 i2s_out, debug_agc_done_0 +mfio41 i2s_out, debug_agc_done_1 +mfio42 i2s_out, debug_ed_cca_ind +mfio43 i2s_out, debug_s2l_done +mfio44 i2s_out +mfio45 i2s_dac_clk, audio_sync +mfio46 audio_trigger +mfio47 i2s_in +mfio48 i2s_in +mfio49 i2s_in +mfio50 i2s_in +mfio51 i2s_in +mfio52 i2s_in +mfio53 i2s_in +mfio54 i2s_in, spdif_in +mfio55 uart0, spim0, spim1 +mfio56 uart0, spim0, spim1 +mfio57 uart0, spim0, spim1 +mfio58 uart0, spim1 +mfio59 uart1 +mfio60 uart1 +mfio61 spdif_out +mfio62 spdif_in +mfio63 eth, mips_trace_clk, mips_trace_data +mfio64 eth, mips_trace_dint, mips_trace_data +mfio65 eth, mips_trace_trigout, mips_trace_data +mfio66 eth, mips_trace_trigin, mips_trace_data +mfio67 eth, mips_trace_dm, mips_trace_data +mfio68 eth, mips_trace_probe_n, mips_trace_data +mfio69 eth, mips_trace_data +mfio70 eth, mips_trace_data +mfio71 eth +mfio72 ir +mfio73 pwmpdm, mips_trace_clk, sram_debug +mfio74 pwmpdm, mips_trace_dint, sram_debug +mfio75 pwmpdm, mips_trace_trigout, rom_debug +mfio76 pwmpdm, mips_trace_trigin, rom_debug +mfio77 mdc_debug, mips_trace_dm, rpu_debug +mfio78 mdc_debug, mips_trace_probe_n, rpu_debug +mfio79 ddr_debug, mips_trace_data, mips_debug +mfio80 ddr_debug, mips_trace_data, mips_debug +mfio81 dreq0, mips_trace_data, eth_debug +mfio82 dreq1, mips_trace_data, eth_debug +mfio83 mips_pll_lock, mips_trace_data, usb_debug +mfio84 audio_pll_lock, mips_trace_data, usb_debug +mfio85 rpu_v_pll_lock, mips_trace_data, sdhost_debug +mfio86 rpu_l_pll_lock, mips_trace_data, sdhost_debug +mfio87 sys_pll_lock, dreq2, socif_debug +mfio88 wifi_pll_lock, dreq3, socif_debug +mfio89 bt_pll_lock, dreq4, dreq5 +tck +trstn +tdi +tms +tdo +jtag_comply +safe_mode +por_disable +resetn + +Example: +-------- +pinctrl@18101c00 { + compatible = "img,pistachio-system-pinctrl"; + reg = <0x18101C00 0x400>; + + gpio0: gpio0 { + interrupts = <GIC_SHARED 71 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + ... + + gpio5: gpio5 { + interrupts = <GIC_SHARED 76 IRQ_TYPE_LEVEL_HIGH>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + ... + + uart0_xfer: uart0-xfer { + uart0-rxd { + pins = "mfio55"; + function = "uart0"; + }; + uart0-txd { + pins = "mfio56"; + function = "uart0"; + }; + }; + + uart0_rts_cts: uart0-rts-cts { + uart0-rts { + pins = "mfio57"; + function = "uart0"; + }; + uart0-cts { + pins = "mfio58"; + function = "uart0"; + }; + }; +}; + +uart@... { + ... + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer>, <&uart0_rts_cts>; + ... +}; + +usb_vbus: fixed-regulator { + ... + gpio = <&gpio5 6 GPIO_ACTIVE_HIGH>; + ... +}; |