diff options
Diffstat (limited to 'Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt | 52 |
1 files changed, 52 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt new file mode 100644 index 000000000..e3c48b20b --- /dev/null +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -0,0 +1,52 @@ +* Freescale (Enhanced) Configurable Serial Peripheral Interface + (CSPI/eCSPI) for i.MX + +Required properties: +- compatible : + - "fsl,imx1-cspi" for SPI compatible with the one integrated on i.MX1 + - "fsl,imx21-cspi" for SPI compatible with the one integrated on i.MX21 + - "fsl,imx27-cspi" for SPI compatible with the one integrated on i.MX27 + - "fsl,imx31-cspi" for SPI compatible with the one integrated on i.MX31 + - "fsl,imx35-cspi" for SPI compatible with the one integrated on i.MX35 + - "fsl,imx51-ecspi" for SPI compatible with the one integrated on i.MX51 + - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc +- reg : Offset and length of the register set for the device +- interrupts : Should contain CSPI/eCSPI interrupt +- clocks : Clock specifiers for both ipg and per clocks. +- clock-names : Clock names should include both "ipg" and "per" +See the clock consumer binding, + Documentation/devicetree/bindings/clock/clock-bindings.txt + +Recommended properties: +- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip +select lines can be used, they appear to always generate a pulse between each +word of a transfer. Most use cases will require GPIO based chip selects to +generate a valid transaction. + +Optional properties: +- num-cs : Number of total chip selects, see spi-bus.txt. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, +Documentation/devicetree/bindings/dma/dma.txt. +- dma-names: DMA request names, if present, should include "tx" and "rx". +- fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register +controlling the SPI_READY handling. Note that to enable the DRCTL consideration, +the SPI_READY mode-flag needs to be set too. +Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst). + +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + +Example: + +ecspi@70010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx51-ecspi"; + reg = <0x70010000 0x4000>; + interrupts = <36>; + cs-gpios = <&gpio3 24 0>, /* GPIO3_24 */ + <&gpio3 25 0>; /* GPIO3_25 */ + dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; + dma-names = "rx", "tx"; + fsl,spi-rdy-drctl = <1>; +}; |