diff options
Diffstat (limited to '')
64 files changed, 3324 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt new file mode 100644 index 000000000..50abb20fe --- /dev/null +++ b/Documentation/devicetree/bindings/usb/allwinner,sun4i-a10-musb.txt @@ -0,0 +1,28 @@ +Allwinner sun4i A10 musb DRC/OTG controller +------------------------------------------- + +Required properties: + - compatible : "allwinner,sun4i-a10-musb", "allwinner,sun6i-a31-musb", + "allwinner,sun8i-a33-musb" or "allwinner,sun8i-h3-musb" + - reg : mmio address range of the musb controller + - clocks : clock specifier for the musb controller ahb gate clock + - reset : reset specifier for the ahb reset (A31 and newer only) + - interrupts : interrupt to which the musb controller is connected + - interrupt-names : must be "mc" + - phys : phy specifier for the otg phy + - phy-names : must be "usb" + - dr_mode : Dual-Role mode must be "host" or "otg" + - extcon : extcon specifier for the otg phy + +Example: + + usb_otg: usb@1c13000 { + compatible = "allwinner,sun4i-a10-musb"; + reg = <0x01c13000 0x0400>; + clocks = <&ahb_gates 0>; + interrupts = <38>; + interrupt-names = "mc"; + phys = <&usbphy 0>; + phy-names = "usb"; + extcon = <&usbphy 0>; + }; diff --git a/Documentation/devicetree/bindings/usb/am33xx-usb.txt b/Documentation/devicetree/bindings/usb/am33xx-usb.txt new file mode 100644 index 000000000..7a198a304 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/am33xx-usb.txt @@ -0,0 +1,199 @@ + AM33xx MUSB +~~~~~~~~~~~~~~~ +- compatible: ti,am33xx-usb +- reg: offset and length of the usbss register sets +- ti,hwmods : must be "usb_otg_hs" + +The glue layer contains multiple child nodes. It is required to have +at least a control module node, USB node and a PHY node. The second USB +node and its PHY node are optional. The DMA node is also optional. + +Reset module +~~~~~~~~~~~~ +- compatible: ti,am335x-usb-ctrl-module +- reg: offset and length of the "USB control registers" in the "Control + Module" block. A second offset and length for the USB wake up control + in the same memory block. +- reg-names: "phy_ctrl" for the "USB control registers" and "wakeup" for + the USB wake up control register. + +USB PHY +~~~~~~~ +compatible: ti,am335x-usb-phy +reg: offset and length of the "USB PHY" register space +ti,ctrl_mod: reference to the "reset module" node +reg-names: phy +The PHY should have a "phy" alias numbered properly in the alias +node. + +USB +~~~ +- compatible: ti,musb-am33xx +- reg: offset and length of "USB Controller Registers", and offset and + length of "USB Core" register space. +- reg-names: control for the ""USB Controller Registers" and "mc" for + "USB Core" register space +- interrupts: USB interrupt number +- interrupt-names: mc +- dr_mode: Should be one of "host", "peripheral" or "otg". +- mentor,multipoint: Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. +- mentor,num-eps: Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" +- mentor,ram-bits: Specifies the ram address size. Should be set to "12" +- mentor,power: Should be "500". This signifies the controller can supply up to + 500mA when operating in host mode. +- phys: reference to the USB phy +- dmas: specifies the dma channels +- dma-names: specifies the names of the channels. Use "rxN" for receive + and "txN" for transmit endpoints. N specifies the endpoint number. + +The controller should have an "usb" alias numbered properly in the alias +node. + +DMA +~~~ +- compatible: ti,am3359-cppi41 +- reg: offset and length of the following register spaces: USBSS, USB + CPPI DMA Controller, USB CPPI DMA Scheduler, USB Queue Manager +- reg-names: glue, controller, scheduler, queuemgr +- #dma-cells: should be set to 2. The first number represents the + endpoint number (0 … 14 for endpoints 1 … 15 on instance 0 and 15 … 29 + for endpoints 1 … 15 on instance 1). The second number is 0 for RX and + 1 for TX transfers. +- #dma-channels: should be set to 30 representing the 15 endpoints for + each USB instance. + +Example: +~~~~~~~~ +The following example contains all the nodes as used on am335x-evm: + +aliases { + usb0 = &usb0; + usb1 = &usb1; + phy0 = &usb0_phy; + phy1 = &usb1_phy; +}; + +usb: usb@47400000 { + compatible = "ti,am33xx-usb"; + reg = <0x47400000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + ti,hwmods = "usb_otg_hs"; + + ctrl_mod: control@44e10000 { + compatible = "ti,am335x-usb-ctrl-module"; + reg = <0x44e10620 0x10 + 0x44e10648 0x4>; + reg-names = "phy_ctrl", "wakeup"; + }; + + usb0_phy: usb-phy@47401300 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401300 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + #phy-cells = <0>; + }; + + usb0: usb@47401000 { + compatible = "ti,musb-am33xx"; + reg = <0x47401400 0x400 + 0x47401000 0x200>; + reg-names = "mc", "control"; + + interrupts = <18>; + interrupt-names = "mc"; + dr_mode = "otg" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb0_phy>; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 4 0 &cppi41dma 5 0 + &cppi41dma 6 0 &cppi41dma 7 0 + &cppi41dma 8 0 &cppi41dma 9 0 + &cppi41dma 10 0 &cppi41dma 11 0 + &cppi41dma 12 0 &cppi41dma 13 0 + &cppi41dma 14 0 &cppi41dma 0 1 + &cppi41dma 1 1 &cppi41dma 2 1 + &cppi41dma 3 1 &cppi41dma 4 1 + &cppi41dma 5 1 &cppi41dma 6 1 + &cppi41dma 7 1 &cppi41dma 8 1 + &cppi41dma 9 1 &cppi41dma 10 1 + &cppi41dma 11 1 &cppi41dma 12 1 + &cppi41dma 13 1 &cppi41dma 14 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + usb1_phy: usb-phy@47401b00 { + compatible = "ti,am335x-usb-phy"; + reg = <0x47401b00 0x100>; + reg-names = "phy"; + ti,ctrl_mod = <&ctrl_mod>; + #phy-cells = <0>; + }; + + usb1: usb@47401800 { + compatible = "ti,musb-am33xx"; + reg = <0x47401c00 0x400 + 0x47401800 0x200>; + reg-names = "mc", "control"; + interrupts = <19>; + interrupt-names = "mc"; + dr_mode = "host" + mentor,multipoint = <1>; + mentor,num-eps = <16>; + mentor,ram-bits = <12>; + mentor,power = <500>; + phys = <&usb1_phy>; + + dmas = <&cppi41dma 15 0 &cppi41dma 16 0 + &cppi41dma 17 0 &cppi41dma 18 0 + &cppi41dma 19 0 &cppi41dma 20 0 + &cppi41dma 21 0 &cppi41dma 22 0 + &cppi41dma 23 0 &cppi41dma 24 0 + &cppi41dma 25 0 &cppi41dma 26 0 + &cppi41dma 27 0 &cppi41dma 28 0 + &cppi41dma 29 0 &cppi41dma 15 1 + &cppi41dma 16 1 &cppi41dma 17 1 + &cppi41dma 18 1 &cppi41dma 19 1 + &cppi41dma 20 1 &cppi41dma 21 1 + &cppi41dma 22 1 &cppi41dma 23 1 + &cppi41dma 24 1 &cppi41dma 25 1 + &cppi41dma 26 1 &cppi41dma 27 1 + &cppi41dma 28 1 &cppi41dma 29 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", "rx5", "rx6", "rx7", + "rx8", "rx9", "rx10", "rx11", "rx12", "rx13", + "rx14", "rx15", + "tx1", "tx2", "tx3", "tx4", "tx5", "tx6", "tx7", + "tx8", "tx9", "tx10", "tx11", "tx12", "tx13", + "tx14", "tx15"; + }; + + cppi41dma: dma-controller@7402000 { + compatible = "ti,am3359-cppi41"; + reg = <0x47400000 0x1000 + 0x47402000 0x1000 + 0x47403000 0x1000 + 0x47404000 0x4000>; + reg-names = "glue", "controller", "scheduler", "queuemgr"; + interrupts = <17>; + interrupt-names = "glue"; + #dma-cells = <2>; + #dma-channels = <30>; + #dma-requests = <256>; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt new file mode 100644 index 000000000..9a8b63190 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/amlogic,dwc3.txt @@ -0,0 +1,42 @@ +Amlogic Meson GX DWC3 USB SoC controller + +Required properties: +- compatible: depending on the SoC this should contain one of: + * amlogic,meson-axg-dwc3 + * amlogic,meson-gxl-dwc3 +- clocks: a handle for the "USB general" clock +- clock-names: must be "usb_general" +- resets: a handle for the shared "USB OTG" reset line +- reset-names: must be "usb_otg" + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +PHY documentation is provided in the following places: +- Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt +- Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt + +Example device nodes: + usb0: usb@ff500000 { + compatible = "amlogic,meson-axg-dwc3"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + clocks = <&clkc CLKID_USB>; + clock-names = "usb_general"; + resets = <&reset RESET_USB_OTG>; + reset-names = "usb_otg"; + + dwc3: dwc3@ff500000 { + compatible = "snps,dwc3"; + reg = <0x0 0xff500000 0x0 0x100000>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "host"; + maximum-speed = "high-speed"; + snps,dis_u2_susphy_quirk; + phys = <&usb3_phy>, <&usb2_phy0>; + phy-names = "usb2-phy", "usb3-phy"; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt new file mode 100644 index 000000000..44e80153b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -0,0 +1,167 @@ +Atmel SOC USB controllers + +OHCI + +Required properties: + - compatible: Should be "atmel,at91rm9200-ohci" for USB controllers + used in host mode. + - reg: Address and length of the register set for the device + - interrupts: Should contain ohci interrupt + - clocks: Should reference the peripheral, host and system clocks + - clock-names: Should contain three strings + "ohci_clk" for the peripheral clock + "hclk" for the host clock + "uhpck" for the system clock + - num-ports: Number of ports. + - atmel,vbus-gpio: If present, specifies a gpio that needs to be + activated for the bus to be powered. + - atmel,oc-gpio: If present, specifies a gpio that needs to be + activated for the overcurrent detection. + +usb0: ohci@500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x100000>; + clocks = <&uhphs_clk>, <&uhphs_clk>, <&uhpck>; + clock-names = "ohci_clk", "hclk", "uhpck"; + interrupts = <20 4>; + num-ports = <2>; +}; + +EHCI + +Required properties: + - compatible: Should be "atmel,at91sam9g45-ehci" for USB controllers + used in host mode. + - reg: Address and length of the register set for the device + - interrupts: Should contain ehci interrupt + - clocks: Should reference the peripheral and the UTMI clocks + - clock-names: Should contain two strings + "ehci_clk" for the peripheral clock + "usb_clk" for the UTMI clock + +usb1: ehci@800000 { + compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; + reg = <0x00800000 0x100000>; + interrupts = <22 4>; + clocks = <&utmi>, <&uhphs_clk>; + clock-names = "usb_clk", "ehci_clk"; +}; + +AT91 USB device controller + +Required properties: + - compatible: Should be one of the following + "atmel,at91rm9200-udc" + "atmel,at91sam9260-udc" + "atmel,at91sam9261-udc" + "atmel,at91sam9263-udc" + - reg: Address and length of the register set for the device + - interrupts: Should contain macb interrupt + - clocks: Should reference the peripheral and the AHB clocks + - clock-names: Should contain two strings + "pclk" for the peripheral clock + "hclk" for the AHB clock + +Optional properties: + - atmel,vbus-gpio: If present, specifies a gpio that needs to be + activated for the bus to be powered. + +usb1: gadget@fffa4000 { + compatible = "atmel,at91rm9200-udc"; + reg = <0xfffa4000 0x4000>; + interrupts = <10 4>; + clocks = <&udc_clk>, <&udpck>; + clock-names = "pclk", "hclk"; + atmel,vbus-gpio = <&pioC 5 0>; +}; + +Atmel High-Speed USB device controller + +Required properties: + - compatible: Should be one of the following + "atmel,at91sam9rl-udc" + "atmel,at91sam9g45-udc" + "atmel,sama5d3-udc" + - reg: Address and length of the register set for the device + - interrupts: Should contain usba interrupt + - clocks: Should reference the peripheral and host clocks + - clock-names: Should contain two strings + "pclk" for the peripheral clock + "hclk" for the host clock + - ep childnode: To specify the number of endpoints and their properties. + +Optional properties: + - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether + vbus is present (USB is connected). + +Required child node properties: + - name: Name of the endpoint. + - reg: Num of the endpoint. + - atmel,fifo-size: Size of the fifo. + - atmel,nb-banks: Number of banks. + - atmel,can-dma: Boolean to specify if the endpoint support DMA. + - atmel,can-isoc: Boolean to specify if the endpoint support ISOC. + +usb2: gadget@fff78000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9rl-udc"; + reg = <0x00600000 0x80000 + 0xfff78000 0x400>; + interrupts = <27 4 0>; + clocks = <&utmi>, <&udphs_clk>; + clock-names = "hclk", "pclk"; + atmel,vbus-gpio = <&pioB 19 0>; + + ep@0 { + reg = <0>; + atmel,fifo-size = <64>; + atmel,nb-banks = <1>; + }; + + ep@1 { + reg = <1>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep@2 { + reg = <2>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <2>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep@3 { + reg = <3>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep@4 { + reg = <4>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + }; + + ep@5 { + reg = <5>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; + + ep@6 { + reg = <6>; + atmel,fifo-size = <1024>; + atmel,nb-banks = <3>; + atmel,can-dma; + atmel,can-isoc; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/brcm,bcm3384-usb.txt b/Documentation/devicetree/bindings/usb/brcm,bcm3384-usb.txt new file mode 100644 index 000000000..452c45c7b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/brcm,bcm3384-usb.txt @@ -0,0 +1,11 @@ +* Broadcom USB controllers + +Required properties: +- compatible: "brcm,bcm3384-ohci", "brcm,bcm3384-ehci" + + These currently use the generic-ohci and generic-ehci drivers. On some + systems, special handling may be needed in the following cases: + + - Restoring state after systemwide power save modes + - Sharing PHYs with the USBD (UDC) hardware + - Figuring out which controllers are disabled on ASIC bondout variants diff --git a/Documentation/devicetree/bindings/usb/brcm,bdc.txt b/Documentation/devicetree/bindings/usb/brcm,bdc.txt new file mode 100644 index 000000000..63e63af3b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/brcm,bdc.txt @@ -0,0 +1,29 @@ +Broadcom USB Device Controller (BDC) +==================================== + +Required properties: + +- compatible: must be one of: + "brcm,bdc-v0.16" + "brcm,bdc" +- reg: the base register address and length +- interrupts: the interrupt line for this controller + +Optional properties: + +On Broadcom STB platforms, these properties are required: + +- phys: phandle to one or two USB PHY blocks + NOTE: Some SoC's have a single phy and some have + USB 2.0 and USB 3.0 phys +- clocks: phandle to the functional clock of this block + +Example: + + bdc@f0b02000 { + compatible = "brcm,bdc-v0.16"; + reg = <0xf0b02000 0xfc4>; + interrupts = <0x0 0x60 0x0>; + phys = <&usbphy_0 0x0>; + clocks = <&sw_usbd>; + }; diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt new file mode 100644 index 000000000..2e9318151 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -0,0 +1,111 @@ +* USB2 ChipIdea USB controller for ci13xxx + +Required properties: +- compatible: should be one of: + "fsl,imx23-usb" + "fsl,imx27-usb" + "fsl,imx28-usb" + "fsl,imx6q-usb" + "fsl,imx6sl-usb" + "fsl,imx6sx-usb" + "fsl,imx6ul-usb" + "fsl,imx7d-usb" + "lsi,zevio-usb" + "qcom,ci-hdrc" + "chipidea,usb2" + "xlnx,zynq-usb-2.20a" +- reg: base address and length of the registers +- interrupts: interrupt for the USB controller + +Recommended properies: +- phy_type: the type of the phy connected to the core. Should be one + of "utmi", "utmi_wide", "ulpi", "serial" or "hsic". Without this + property the PORTSC register won't be touched. +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +Deprecated properties: +- usb-phy: phandle for the PHY device. Use "phys" instead. +- fsl,usbphy: phandle of usb phy that connects to the port. Use "phys" instead. + +Optional properties: +- clocks: reference to the USB clock +- phys: reference to the USB PHY +- phy-names: should be "usb-phy" +- vbus-supply: reference to the VBUS regulator +- maximum-speed: limit the maximum connection speed to "full-speed". +- tpl-support: TPL (Targeted Peripheral List) feature for targeted hosts +- itc-setting: interrupt threshold control register control, the setting + should be aligned with ITC bits at register USBCMD. +- ahb-burst-config: it is vendor dependent, the required value should be + aligned with AHBBRST at SBUSCFG, the range is from 0x0 to 0x7. This + property is used to change AHB burst configuration, check the chipidea + spec for meaning of each value. If this property is not existed, it + will use the reset value. +- tx-burst-size-dword: it is vendor dependent, the tx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from system memory to the USB + bus, the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- rx-burst-size-dword: it is vendor dependent, the rx burst size in dword + (4 bytes), This register represents the maximum length of a the burst + in 32-bit words while moving data from the USB bus to system memory, + the value of this property will only take effect if property + "ahb-burst-config" is set to 0, if this property is missing the reset + default of the hardware implementation will be used. +- extcon: phandles to external connector devices. First phandle should point to + external connector, which provide "USB" cable events, the second should point + to external connector device, which provide "USB-HOST" cable events. If one + of the external connector devices is not required, empty <0> phandle should + be specified. +- phy-clkgate-delay-us: the delay time (us) between putting the PHY into + low power mode and gating the PHY clock. +- non-zero-ttctrl-ttha: after setting this property, the value of register + ttctrl.ttha will be 0x7f; if not, the value will be 0x0, this is the default + value. It needs to be very carefully for setting this property, it is + recommended that consult with your IC engineer before setting this value. + On the most of chipidea platforms, the "usage_tt" flag at RTL is 0, so this + property only affects siTD. + If this property is not set, the max packet size is 1023 bytes, and if + the total of packet size for pervious transactions are more than 256 bytes, + it can't accept any transactions within this frame. The use case is single + transaction, but higher frame rate. + If this property is set, the max packet size is 188 bytes, it can handle + more transactions than above case, it can accept transactions until it + considers the left room size within frame is less than 188 bytes, software + needs to make sure it does not send more than 90% + maximum_periodic_data_per_frame. The use case is multiple transactions, but + less frame rate. +- mux-controls: The mux control for toggling host/device output of this + controller. It's expected that a mux state of 0 indicates device mode and a + mux state of 1 indicates host mode. +- mux-control-names: Shall be "usb_switch" if mux-controls is specified. + +i.mx specific properties +- fsl,usbmisc: phandler of non-core register device, with one + argument that indicate usb controller index +- disable-over-current: disable over current detect +- over-current-active-high: over current signal polarity is high active, + typically over current signal polarity is low active. +- external-vbus-divider: enables off-chip resistor divider for Vbus + +Example: + + usb@f7ed0000 { + compatible = "chipidea,usb2"; + reg = <0xf7ed0000 0x10000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&chip CLKID_USB0>; + phys = <&usb_phy0>; + phy-names = "usb-phy"; + vbus-supply = <®_usb0_vbus>; + itc-setting = <0x4>; /* 4 micro-frames */ + /* Incremental burst of unspecified length */ + ahb-burst-config = <0x0>; + tx-burst-size-dword = <0x10>; /* 64 bytes */ + rx-burst-size-dword = <0x10>; + extcon = <0>, <&usb_id>; + phy-clkgate-delay-us = <400>; + mux-controls = <&usb_switch>; + mux-control-names = "usb_switch"; + }; diff --git a/Documentation/devicetree/bindings/usb/da8xx-usb.txt b/Documentation/devicetree/bindings/usb/da8xx-usb.txt new file mode 100644 index 000000000..9ce22551b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/da8xx-usb.txt @@ -0,0 +1,80 @@ +TI DA8xx MUSB +~~~~~~~~~~~~~ +For DA8xx/OMAP-L1x/AM17xx/AM18xx platforms. + +Required properties: +~~~~~~~~~~~~~~~~~~~~ + - compatible : Should be set to "ti,da830-musb". + + - reg: Offset and length of the USB controller register set. + + - interrupts: The USB interrupt number. + + - interrupt-names: Should be set to "mc". + + - dr_mode: The USB operation mode. Should be one of "host", "peripheral" or "otg". + + - phys: Phandle for the PHY device + + - phy-names: Should be "usb-phy" + + - dmas: specifies the dma channels + + - dma-names: specifies the names of the channels. Use "rxN" for receive + and "txN" for transmit endpoints. N specifies the endpoint number. + +Optional properties: +~~~~~~~~~~~~~~~~~~~~ + - vbus-supply: Phandle to a regulator providing the USB bus power. + +DMA +~~~ +- compatible: ti,da830-cppi41 +- reg: offset and length of the following register spaces: CPPI DMA Controller, + CPPI DMA Scheduler, Queue Manager +- reg-names: "controller", "scheduler", "queuemgr" +- #dma-cells: should be set to 2. The first number represents the + channel number (0 … 3 for endpoints 1 … 4). + The second number is 0 for RX and 1 for TX transfers. +- #dma-channels: should be set to 4 representing the 4 endpoints. + +Example: + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <0>; + }; + usb0: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x00200000 0x1000>; + ranges; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <58>; + interrupt-names = "mc"; + + dr_mode = "host"; + vbus-supply = <&usb_vbus>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + + dmas = <&cppi41dma 0 0 &cppi41dma 1 0 + &cppi41dma 2 0 &cppi41dma 3 0 + &cppi41dma 0 1 &cppi41dma 1 1 + &cppi41dma 2 1 &cppi41dma 3 1>; + dma-names = + "rx1", "rx2", "rx3", "rx4", + "tx1", "tx2", "tx3", "tx4"; + + + cppi41dma: dma-controller@201000 { + compatible = "ti,da830-cppi41"; + reg = <0x201000 0x1000 + 0x202000 0x1000 + 0x204000 0x4000>; + reg-names = "controller", "scheduler", "queuemgr"; + interrupts = <58>; + #dma-cells = <2>; + #dma-channels = <4>; + }; + + }; diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt new file mode 100644 index 000000000..46da5f184 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc2.txt @@ -0,0 +1,53 @@ +Platform DesignWare HS OTG USB 2.0 controller +----------------------------------------------------- + +Required properties: +- compatible : One of: + - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC. + - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC. + - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc; + - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc; + - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc; + - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs; + - "lantiq,xrx200-usb": The DWC2 USB controller instance in Lantiq XRX SoCs; + - "amlogic,meson8-usb": The DWC2 USB controller instance in Amlogic Meson8 SoCs; + - "amlogic,meson8b-usb": The DWC2 USB controller instance in Amlogic Meson8b SoCs; + - "amlogic,meson-gxbb-usb": The DWC2 USB controller instance in Amlogic S905 SoCs; + - "amcc,dwc-otg": The DWC2 USB controller instance in AMCC Canyonlands 460EX SoCs; + - snps,dwc2: A generic DWC2 USB controller with default parameters. + - "st,stm32f4x9-fsotg": The DWC2 USB FS/HS controller instance in STM32F4x9 SoCs + configured in FS mode; + - "st,stm32f4x9-hsotg": The DWC2 USB HS controller instance in STM32F4x9 SoCs + configured in HS mode; + - "st,stm32f7-hsotg": The DWC2 USB HS controller instance in STM32F7 SoCs + configured in HS mode; +- reg : Should contain 1 register range (address and length) +- interrupts : Should contain 1 interrupt +- clocks: clock provider specifier +- clock-names: shall be "otg" +Refer to clk/clock-bindings.txt for generic clock consumer properties + +Optional properties: +- phys: phy provider specifier +- phy-names: shall be "usb2-phy" +Refer to phy/phy-bindings.txt for generic phy consumer properties +- dr_mode: shall be one of "host", "peripheral" and "otg" + Refer to usb/generic.txt +- g-rx-fifo-size: size of rx fifo size in gadget mode. +- g-np-tx-fifo-size: size of non-periodic tx fifo size in gadget mode. +- g-tx-fifo-size: size of periodic tx fifo per endpoint (except ep0) in gadget mode. + +Deprecated properties: +- g-use-dma: gadget DMA mode is automatically detected + +Example: + + usb@101c0000 { + compatible = "ralink,rt3050-usb, snps,dwc2"; + reg = <0x101c0000 40000>; + interrupts = <18>; + clocks = <&usb_otg_ahb_clk>; + clock-names = "otg"; + phys = <&usbphy>; + phy-names = "usb2-phy"; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3-cavium.txt b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt new file mode 100644 index 000000000..710b782cc --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-cavium.txt @@ -0,0 +1,28 @@ +Cavium SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Should contain "cavium,octeon-7130-usb-uctl" + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Example device node: + + uctl@1180069000000 { + compatible = "cavium,octeon-7130-usb-uctl"; + reg = <0x00011800 0x69000000 0x00000000 0x00000100>; + ranges; + #address-cells = <0x00000002>; + #size-cells = <0x00000002>; + refclk-frequency = <0x05f5e100>; + refclk-type-ss = "dlmc_ref_clk0"; + refclk-type-hs = "dlmc_ref_clk0"; + power = <0x00000002 0x00000002 0x00000001>; + xhci@1690000000000 { + compatible = "cavium,octeon-7130-xhci", "synopsys,dwc3"; + reg = <0x00016900 0x00000000 0x00000010 0x00000000>; + interrupt-parent = <0x00000010>; + interrupts = <0x00000009 0x00000004>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3-st.txt b/Documentation/devicetree/bindings/usb/dwc3-st.txt new file mode 100644 index 000000000..df0e02e1e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-st.txt @@ -0,0 +1,66 @@ +ST DWC3 glue logic + +This file documents the parameters for the dwc3-st driver. +This driver controls the glue logic used to configure the dwc3 core on +STiH407 based platforms. + +Required properties: + - compatible : must be "st,stih407-dwc3" + - reg : glue logic base address and USB syscfg ctrl register offset + - reg-names : should be "reg-glue" and "syscfg-reg" + - st,syscon : should be phandle to system configuration node which + encompasses the glue registers + - resets : list of phandle and reset specifier pairs. There should be two entries, one + for the powerdown and softreset lines of the usb3 IP + - reset-names : list of reset signal names. Names should be "powerdown" and "softreset" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property + + - pinctl-names : A pinctrl state named "default" must be defined +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + + - pinctrl-0 : Pin control group +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + +Sub-nodes: +The dwc3 core should be added as subnode to ST DWC3 glue as shown in the +example below. The DT binding details of dwc3 can be found in: +Documentation/devicetree/bindings/usb/dwc3.txt + +NB: The dr_mode property described in [1] is NOT optional for this driver, as the default value +is "otg", which isn't supported by this SoC. Valid dr_mode values for dwc3-st are either "host" +or "device". + +[1] Documentation/devicetree/bindings/usb/generic.txt + +Example: + +st_dwc3: dwc3@8f94000 { + compatible = "st,stih407-dwc3"; + reg = <0x08f94000 0x1000>, <0x110 0x4>; + reg-names = "reg-glue", "syscfg-reg"; + st,syscfg = <&syscfg_core>; + resets = <&powerdown STIH407_USB3_POWERDOWN>, + <&softreset STIH407_MIPHY2_SOFTRESET>; + reset-names = "powerdown", "softreset"; + #address-cells = <1>; + #size-cells = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb3>; + ranges; + + dwc3: dwc3@9900000 { + compatible = "snps,dwc3"; + reg = <0x09900000 0x100000>; + interrupts = <GIC_SPI 155 IRQ_TYPE_NONE>; + dr_mode = "host"; + phy-names = "usb2-phy", "usb3-phy"; + phys = <&usb2_picophy2>, <&phy_port2 PHY_TYPE_USB3>; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt new file mode 100644 index 000000000..4aae5b2ce --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3-xilinx.txt @@ -0,0 +1,32 @@ +Xilinx SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Should contain "xlnx,zynqmp-dwc3" +- clocks: A list of phandles for the clocks listed in clock-names +- clock-names: Should contain the following: + "bus_clk" Master/Core clock, have to be >= 125 MHz for SS + operation and >= 60MHz for HS operation + + "ref_clk" Clock source to core during PHY power down + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Example device node: + + usb@0 { + #address-cells = <0x2>; + #size-cells = <0x1>; + compatible = "xlnx,zynqmp-dwc3"; + clock-names = "bus_clk" "ref_clk"; + clocks = <&clk125>, <&clk125>; + ranges; + + dwc3@fe200000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe200000 0x40000>; + interrupts = <0x0 0x41 0x4>; + dr_mode = "host"; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt new file mode 100644 index 000000000..ae46c0ac9 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -0,0 +1,119 @@ +synopsys DWC3 CORE + +DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties + as described in 'usb/generic.txt' + +Required properties: + - compatible: must be "snps,dwc3" + - reg : Address and length of the register set for the device + - interrupts: Interrupts used by the dwc3 controller. + - clock-names: should contain "ref", "bus_early", "suspend" + - clocks: list of phandle and clock specifier pairs corresponding to + entries in the clock-names property. + +Exception for clocks: + clocks are optional if the parent node (i.e. glue-layer) is compatible to + one of the following: + "amlogic,meson-axg-dwc3" + "amlogic,meson-gxl-dwc3" + "cavium,octeon-7130-usb-uctl" + "qcom,dwc3" + "samsung,exynos5250-dwusb3" + "samsung,exynos7-dwusb3" + "sprd,sc9860-dwc3" + "st,stih407-dwc3" + "ti,am437x-dwc3" + "ti,dwc3" + "ti,keystone-dwc3" + "rockchip,rk3399-dwc3" + "xlnx,zynqmp-dwc3" + +Optional properties: + - usb-phy : array of phandle for the PHY device. The first element + in the array is expected to be a handle to the USB2/HS PHY and + the second element is expected to be a handle to the USB3/SS PHY + - phys: from the *Generic PHY* bindings + - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" + or "usb3-phy". + - resets: a single pair of phandle and reset specifier + - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable + - snps,disable_scramble_quirk: true when SW should disable data scrambling. + Only really useful for FPGA builds. + - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled + - snps,lpm-nyet-threshold: LPM NYET threshold + - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk + - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk + - snps,req_p1p2p3_quirk: when set, the core will always request for + P1/P2/P3 transition sequence. + - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain + amount of 8B10B errors occur. + - snps,del_phy_power_chg_quirk: when set core will delay PHY power change + from P0 to P1/P2/P3. + - snps,lfps_filter_quirk: when set core will filter LFPS reception. + - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start + Polling LFPS after RX.Detect. + - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value. + - snps,tx_de_emphasis: the value driven to the PHY is controlled by the + LTSSM during USB3 Compliance mode. + - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy. + - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. + - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, + disabling the suspend signal to the PHY. + - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection + in PHY P3 power state. + - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists + in GUSB2PHYCFG, specify that USB2 PHY doesn't provide + a free-running PHY clock. + - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power + from P0 to P1/P2/P3 without delay. + - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check + during HS transmit. + - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in + park mode are disabled. + - snps,dis_metastability_quirk: when set, disable metastability workaround. + CAUTION: use only if you are absolutely sure of it. + - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal + utmi_l1_suspend_n, false when asserts utmi_sleep_n + - snps,hird-threshold: HIRD threshold + - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for + UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3. + - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ + register for post-silicon frame length adjustment when the + fladj_30mhz_sdbnd signal is invalid or incorrect. + - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode + only. Set this and rx-max-burst-prd to a valid, + non-zero value 1-16 (DWC_usb31 programming guide + section 1.2.4) to enable periodic ESS RX threshold. + - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set + this and rx-thr-num-pkt-prd to a valid, non-zero value + 1-16 (DWC_usb31 programming guide section 1.2.4) to + enable periodic ESS RX threshold. + - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode + only. Set this and tx-max-burst-prd to a valid, + non-zero value 1-16 (DWC_usb31 programming guide + section 1.2.3) to enable periodic ESS TX threshold. + - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set + this and tx-thr-num-pkt-prd to a valid, non-zero value + 1-16 (DWC_usb31 programming guide section 1.2.3) to + enable periodic ESS TX threshold. + + - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. + - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0 + register, undefined length INCR burst type enable and INCRx type. + When just one value, which means INCRX burst mode enabled. When + more than one value, which means undefined length INCR burst type + enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256. + + - in addition all properties from usb-xhci.txt from the current directory are + supported as well + + +This is usually a subnode to DWC3 glue to which it is connected. + +dwc3@4a030000 { + compatible = "snps,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; +}; diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt new file mode 100644 index 000000000..d77e11a97 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt @@ -0,0 +1,31 @@ +OMAP HS USB EHCI controller + +This device is usually the child of the omap-usb-host +Documentation/devicetree/bindings/mfd/omap-usb-host.txt + +Required properties: + +- compatible: should be "ti,ehci-omap" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Optional properties: + +- phys: list of phandles to PHY nodes. + This property is required if at least one of the ports are in + PHY mode i.e. OMAP_EHCI_PORT_MODE_PHY + +To specify the port mode, see +Documentation/devicetree/bindings/mfd/omap-usb-host.txt + +Example for OMAP4: + +usbhsehci: ehci@4a064c00 { + compatible = "ti,ehci-omap"; + reg = <0x4a064c00 0x400>; + interrupts = <0 77 0x4>; +}; + +&usbhsehci { + phys = <&hsusb1_phy 0 &hsusb3_phy>; +}; diff --git a/Documentation/devicetree/bindings/usb/ehci-orion.txt b/Documentation/devicetree/bindings/usb/ehci-orion.txt new file mode 100644 index 000000000..2855bae79 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-orion.txt @@ -0,0 +1,22 @@ +* EHCI controller, Orion Marvell variants + +Required properties: +- compatible: must be one of the following + "marvell,orion-ehci" + "marvell,armada-3700-ehci" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The EHCI interrupt + +Optional properties: +- clocks: reference to the clock +- phys: reference to the USB PHY +- phy-names: name of the USB PHY, should be "usb" + +Example: + + ehci@50000 { + compatible = "marvell,orion-ehci"; + reg = <0x50000 0x1000>; + interrupts = <19>; + }; diff --git a/Documentation/devicetree/bindings/usb/ehci-st.txt b/Documentation/devicetree/bindings/usb/ehci-st.txt new file mode 100644 index 000000000..065c91d95 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ehci-st.txt @@ -0,0 +1,38 @@ +ST USB EHCI controller + +Required properties: + - compatible : must be "st,st-ehci-300x" + - reg : physical base addresses of the controller and length of memory mapped + region + - interrupts : one EHCI interrupt should be described here + - pinctrl-names : a pinctrl state named "default" must be defined + - pinctrl-0 : phandle referencing pin configuration of the USB controller +See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + - clocks : phandle list of usb clocks + - clock-names : should be "ic" for interconnect clock and "clk48" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + - phys : phandle for the PHY device + - phy-names : should be "usb" + - resets : phandle + reset specifier pairs to the powerdown and softreset lines + of the USB IP + - reset-names : should be "power" and "softreset" +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + + ehci1: usb@fe203e00 { + compatible = "st,st-ehci-300x"; + reg = <0xfe203e00 0x100>; + interrupts = <GIC_SPI 148 IRQ_TYPE_NONE>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1>; + clocks = <&clk_s_a1_ls 0>; + phys = <&usb2_phy>; + phy-names = "usb"; + + resets = <&powerdown STIH416_USB1_POWERDOWN>, + <&softreset STIH416_USB1_SOFTRESET>; + reset-names = "power", "softreset"; + }; diff --git a/Documentation/devicetree/bindings/usb/exynos-usb.txt b/Documentation/devicetree/bindings/usb/exynos-usb.txt new file mode 100644 index 000000000..c97374315 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/exynos-usb.txt @@ -0,0 +1,119 @@ +Samsung Exynos SoC USB controller + +The USB devices interface with USB controllers on Exynos SOCs. +The device node has following properties. + +EHCI +Required properties: + - compatible: should be "samsung,exynos4210-ehci" for USB 2.0 + EHCI controller in host mode. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - clocks: from common clock binding: handle to usb clock. + - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are EHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on EHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings; specifying phy used by port. + +Optional properties: + - samsung,vbus-gpio: if present, specifies the GPIO that + needs to be pulled up for the bus to be powered. + +Example: + + usb@12110000 { + compatible = "samsung,exynos4210-ehci"; + reg = <0x12110000 0x100>; + interrupts = <0 71 0>; + samsung,vbus-gpio = <&gpx2 6 1 3 3>; + + clocks = <&clock 285>; + clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + }; + }; + +OHCI +Required properties: + - compatible: should be "samsung,exynos4210-ohci" for USB 2.0 + OHCI companion controller in host mode. + - reg: physical base address of the controller and length of memory mapped + region. + - interrupts: interrupt number to the cpu. + - clocks: from common clock binding: handle to usb clock. + - clock-names: from common clock binding: Shall be "usbhost". + - port: if in the SoC there are OHCI phys, they should be listed here. + One phy per port. Each port should have following entries: + - reg: port number on OHCI controller, e.g + On Exynos5250, port 0 is USB2.0 otg phy + port 1 is HSIC phy0 + port 2 is HSIC phy1 + - phys: from the *Generic PHY* bindings, specifying phy used by port. + +Example: + usb@12120000 { + compatible = "samsung,exynos4210-ohci"; + reg = <0x12120000 0x100>; + interrupts = <0 71 0>; + + clocks = <&clock 285>; + clock-names = "usbhost"; + + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + phys = <&usb2phy 1>; + }; + + }; + +DWC3 +Required properties: + - compatible: should be one of the following - + "samsung,exynos5250-dwusb3": for USB 3.0 DWC3 controller on + Exynos5250/5420. + "samsung,exynos7-dwusb3": for USB 3.0 DWC3 controller on Exynos7. + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property. + - ranges: allows valid 1:1 translation between child's address space and + parent's address space + - clocks: Clock IDs array as required by the controller. + - clock-names: names of clocks correseponding to IDs in the clock property + - vdd10-supply: 1.0V powr supply + - vdd33-supply: 3.0V/3.3V power supply + +Sub-nodes: +The dwc3 core should be added as subnode to Exynos dwc3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +Example: + usb@12000000 { + compatible = "samsung,exynos5250-dwusb3"; + clocks = <&clock 286>; + clock-names = "usbdrd30"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + vdd10-supply = <&ldo11_reg>; + vdd33-supply = <&ldo9_reg>; + + dwc3 { + compatible = "synopsys,dwc3"; + reg = <0x12000000 0x10000>; + interrupts = <0 72 0>; + usb-phy = <&usb2_phy &usb3_phy>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/fcs,fusb302.txt b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt new file mode 100644 index 000000000..6087dc7f2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/fcs,fusb302.txt @@ -0,0 +1,23 @@ +Fairchild FUSB302 Type-C Port controllers + +Required properties : +- compatible : "fcs,fusb302" +- reg : I2C slave address +- interrupts : Interrupt specifier + +Optional properties : +- fcs,operating-sink-microwatt : + Minimum amount of power accepted from a sink + when negotiating + +Example: + +fusb302: typec-portc@54 { + compatible = "fcs,fusb302"; + reg = <0x54>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + fcs,max-sink-microvolt = <12000000>; + fcs,max-sink-microamp = <3000000>; + fcs,max-sink-microwatt = <36000000>; +}; diff --git a/Documentation/devicetree/bindings/usb/fsl-usb.txt b/Documentation/devicetree/bindings/usb/fsl-usb.txt new file mode 100644 index 000000000..0b08b006c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/fsl-usb.txt @@ -0,0 +1,81 @@ +Freescale SOC USB controllers + +The device node for a USB controller that is part of a Freescale +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : Should be "fsl-usb2-mph" for multi port host USB + controllers, or "fsl-usb2-dr" for dual role USB controllers + or "fsl,mpc5121-usb2-dr" for dual role USB controllers of MPC5121. + Wherever applicable, the IP version of the USB controller should + also be mentioned (for eg. fsl-usb2-dr-v2.2 for bsc9132). + - phy_type : For multi port host USB controllers, should be one of + "ulpi", or "serial". For dual role USB controllers, should be + one of "ulpi", "utmi", "utmi_wide", or "serial". + - reg : Offset and length of the register set for the device + - port0 : boolean; if defined, indicates port0 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port1" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - port1 : boolean; if defined, indicates port1 is connected for + fsl-usb2-mph compatible controllers. Either this property or + "port0" (or both) must be defined for "fsl-usb2-mph" compatible + controllers. + - dr_mode : indicates the working mode for "fsl-usb2-dr" compatible + controllers. Can be "host", "peripheral", or "otg". Default to + "host" if not defined for backward compatibility. + +Recommended properties : + - interrupts : <a b> where a is the interrupt number and b is a + field that represents an encoding of the sense and level + information for the interrupt. This should be encoded based on + the information in section 2) depending on the type of interrupt + controller you have. + +Optional properties : + - fsl,invert-drvvbus : boolean; for MPC5121 USB0 only. Indicates the + port power polarity of internal PHY signal DRVVBUS is inverted. + - fsl,invert-pwr-fault : boolean; for MPC5121 USB0 only. Indicates + the PWR_FAULT signal polarity is inverted. + +Example multi port host USB controller device node : + usb@22000 { + compatible = "fsl-usb2-mph"; + reg = <22000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <27 1>; + phy_type = "ulpi"; + port0; + port1; + }; + +Example dual role USB controller device node : + usb@23000 { + compatible = "fsl-usb2-dr"; + reg = <23000 1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = <700>; + interrupts = <26 1>; + dr_mode = "otg"; + phy = "ulpi"; + }; + +Example dual role USB controller device node for MPC5121ADS: + + usb@4000 { + compatible = "fsl,mpc5121-usb2-dr"; + reg = <0x4000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + interrupt-parent = < &ipic >; + interrupts = <44 0x8>; + dr_mode = "otg"; + phy_type = "utmi_wide"; + fsl,invert-drvvbus; + fsl,invert-pwr-fault; + }; diff --git a/Documentation/devicetree/bindings/usb/generic.txt b/Documentation/devicetree/bindings/usb/generic.txt new file mode 100644 index 000000000..0a74ab8df --- /dev/null +++ b/Documentation/devicetree/bindings/usb/generic.txt @@ -0,0 +1,46 @@ +Generic USB Properties + +Optional properties: + - maximum-speed: tells USB controllers we want to work up to a certain + speed. Valid arguments are "super-speed", "high-speed", + "full-speed" and "low-speed". In case this isn't passed + via DT, USB controllers should default to their maximum + HW capability. + - dr_mode: tells Dual-Role USB controllers that we want to work on a + particular mode. Valid arguments are "host", + "peripheral" and "otg". In case this attribute isn't + passed via DT, USB DRD controllers should default to + OTG. + - phy_type: tells USB controllers that we want to configure the core to support + a UTMI+ PHY with an 8- or 16-bit interface if UTMI+ is + selected. Valid arguments are "utmi" and "utmi_wide". + In case this isn't passed via DT, USB controllers should + default to HW capability. + - otg-rev: tells usb driver the release number of the OTG and EH supplement + with which the device and its descriptors are compliant, + in binary-coded decimal (i.e. 2.0 is 0200H). This + property is used if any real OTG features(HNP/SRP/ADP) + is enabled, if ADP is required, otg-rev should be + 0x0200 or above. + - companion: phandle of a companion + - hnp-disable: tells OTG controllers we want to disable OTG HNP, normally HNP + is the basic function of real OTG except you want it + to be a srp-capable only B device. + - srp-disable: tells OTG controllers we want to disable OTG SRP, SRP is + optional for OTG device. + - adp-disable: tells OTG controllers we want to disable OTG ADP, ADP is + optional for OTG device. + +This is an attribute to a USB controller such as: + +dwc3@4a030000 { + compatible = "synopsys,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + maximum-speed = "super-speed"; + dr_mode = "otg"; + phy_type = "utmi_wide"; + otg-rev = <0x0200>; + adp-disable; +}; diff --git a/Documentation/devicetree/bindings/usb/gr-udc.txt b/Documentation/devicetree/bindings/usb/gr-udc.txt new file mode 100644 index 000000000..e9445224f --- /dev/null +++ b/Documentation/devicetree/bindings/usb/gr-udc.txt @@ -0,0 +1,34 @@ +USB Peripheral Controller driver for Aeroflex Gaisler GRUSBDC. + +The GRUSBDC USB Device Controller core is available in the GRLIB VHDL +IP core library. + +Note: In the ordinary environment for the core, a Leon SPARC system, +these properties are built from information in the AMBA plug&play. + +Required properties: + +- name : Should be "GAISLER_USBDC" or "01_021" + +- reg : Address and length of the register set for the device + +- interrupts : Interrupt numbers for this device. Either one interrupt number + for all interrupts, or one for status related interrupts, one for IN + endpoint related interrupts and one for OUT endpoint related interrupts. + +Optional properties: + +- epobufsizes : Array of buffer sizes for OUT endpoints when they differ + from the default size of 1024. The array is indexed by the OUT endpoint + number. If the property is present it typically contains one entry for + each OUT endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. + +- epibufsizes : Array of buffer sizes for IN endpoints when they differ + from the default size of 1024. The array is indexed by the IN endpoint + number. If the property is present it typically contains one entry for + each IN endpoint of the core. Fewer entries overrides the default sizes + only for as many endpoints as the array contains. + +For further information look in the documentation for the GLIB IP core library: +http://www.gaisler.com/products/grlib/grip.pdf diff --git a/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt new file mode 100644 index 000000000..f4633496b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/hisilicon,histb-xhci.txt @@ -0,0 +1,45 @@ +HiSilicon STB xHCI + +The device node for HiSilicon STB xHCI host controller + +Required properties: + - compatible: should be "hisilicon,hi3798cv200-xhci" + - reg: specifies physical base address and size of the registers + - interrupts : interrupt used by the controller + - clocks: a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names: must contain + "bus": for bus clock + "utmi": for utmi clock + "pipe": for pipe clock + "suspend": for suspend clock + - resets: a list of phandle and reset specifier pairs as listed in + reset-names property. + - reset-names: must contain + "soft": for soft reset + - phys: a list of phandle + phy specifier pairs + - phy-names: must contain at least one of following: + "inno": for inno phy + "combo": for combo phy + +Optional properties: + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM + - usb3-lpm-capable: determines if platform is USB3 LPM capable + - imod-interval-ns: default interrupt moderation interval is 40000ns + +Example: + +xhci0: xchi@f98a0000 { + compatible = "hisilicon,hi3798cv200-xhci"; + reg = <0xf98a0000 0x10000>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg HISTB_USB3_BUS_CLK>, + <&crg HISTB_USB3_UTMI_CLK>, + <&crg HISTB_USB3_PIPE_CLK>, + <&crg HISTB_USB3_SUSPEND_CLK>; + clock-names = "bus", "utmi", "pipe", "suspend"; + resets = <&crg 0xb0 12>; + reset-names = "soft"; + phys = <&usb2_phy1_port1 0>, <&combphy0 PHY_TYPE_USB3>; + phy-names = "inno", "combo"; +}; diff --git a/Documentation/devicetree/bindings/usb/iproc-udc.txt b/Documentation/devicetree/bindings/usb/iproc-udc.txt new file mode 100644 index 000000000..272d7faf1 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/iproc-udc.txt @@ -0,0 +1,21 @@ +Broadcom IPROC USB Device controller. + +The device node is used for UDCs integrated into Broadcom's +iProc family (Northstar2, Cygnus) of SoCs'. The UDC is based +on Synopsys Designware Cores AHB Subsystem Device Controller +IP. + +Required properties: + - compatible: Add the compatibility strings for supported platforms. + For Broadcom NS2 platform, add "brcm,ns2-udc","brcm,iproc-udc". + For Broadcom Cygnus platform, add "brcm,cygnus-udc", "brcm,iproc-udc". + - reg: Offset and length of UDC register set + - interrupts: description of interrupt line + - phys: phandle to phy node. + +Example: + udc_dwc: usb@664e0000 { + compatible = "brcm,ns2-udc", "brcm,iproc-udc"; + reg = <0x664e0000 0x2000>; + interrupts = <GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH>; + phys = <&usbdrd_phy>; diff --git a/Documentation/devicetree/bindings/usb/isp1301.txt b/Documentation/devicetree/bindings/usb/isp1301.txt new file mode 100644 index 000000000..ecd607dac --- /dev/null +++ b/Documentation/devicetree/bindings/usb/isp1301.txt @@ -0,0 +1,24 @@ +* NXP ISP1301 USB transceiver + +Required properties: +- compatible: must be "nxp,isp1301" +- reg: I2C address of the ISP1301 device + +Optional properties of devices using ISP1301: +- transceiver: phandle of isp1301 - this helps the ISP1301 driver to find the + ISP1301 instance associated with the respective USB driver + +Example: + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; + + usbd@31020000 { + compatible = "nxp,lpc3220-udc"; + reg = <0x31020000 0x300>; + interrupt-parent = <&mic>; + interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; + transceiver = <&isp1301>; + }; diff --git a/Documentation/devicetree/bindings/usb/keystone-usb.txt b/Documentation/devicetree/bindings/usb/keystone-usb.txt new file mode 100644 index 000000000..f96e09f78 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/keystone-usb.txt @@ -0,0 +1,54 @@ +TI Keystone Soc USB Controller + +DWC3 GLUE + +Required properties: + - compatible: should be "ti,keystone-dwc3". + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property. + - reg : Address and length of the register set for the USB subsystem on + the SOC. + - interrupts : The irq number of this device that is used to interrupt the + MPU. + - ranges: allows valid 1:1 translation between child's address space and + parent's address space. + +SoC-specific Required Properties: +The following are mandatory properties for Keystone 2 66AK2HK, 66AK2L and 66AK2E +SoCs only: + +- clocks: Clock ID for USB functional clock. +- clock-names: Must be "usb". + + +The following are mandatory properties for Keystone 2 66AK2G SoCs only: + +- power-domains: Should contain a phandle to a PM domain provider node + and an args specifier containing the USB device id + value. This property is as per the binding, + Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt + +Sub-nodes: +The dwc3 core should be added as subnode to Keystone DWC3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +Example: + usb: usb@2680000 { + compatible = "ti,keystone-dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2680000 0x10000>; + clocks = <&clkusb>; + clock-names = "usb"; + interrupts = <GIC_SPI 393 IRQ_TYPE_EDGE_RISING>; + ranges; + + dwc3@2690000 { + compatible = "synopsys,dwc3"; + reg = <0x2690000 0x70000>; + interrupts = <GIC_SPI 393 IRQ_TYPE_EDGE_RISING>; + usb-phy = <&usb_phy>, <&usb_phy>; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/lpc32xx-udc.txt b/Documentation/devicetree/bindings/usb/lpc32xx-udc.txt new file mode 100644 index 000000000..29f12a533 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/lpc32xx-udc.txt @@ -0,0 +1,28 @@ +* NXP LPC32xx SoC USB Device Controller (UDC) + +Required properties: +- compatible: Must be "nxp,lpc3220-udc" +- reg: Physical base address of the controller and length of memory mapped + region. +- interrupts: The USB interrupts: + * USB Device Low Priority Interrupt + * USB Device High Priority Interrupt + * USB Device DMA Interrupt + * External USB Transceiver Interrupt (OTG ATX) +- transceiver: phandle of the associated ISP1301 device - this is necessary for + the UDC controller for connecting to the USB physical layer + +Example: + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; + + usbd@31020000 { + compatible = "nxp,lpc3220-udc"; + reg = <0x31020000 0x300>; + interrupt-parent = <&mic>; + interrupts = <0x3d 0>, <0x3e 0>, <0x3c 0>, <0x3a 0>; + transceiver = <&isp1301>; + }; diff --git a/Documentation/devicetree/bindings/usb/maxim,max3421.txt b/Documentation/devicetree/bindings/usb/maxim,max3421.txt new file mode 100644 index 000000000..90495b1ae --- /dev/null +++ b/Documentation/devicetree/bindings/usb/maxim,max3421.txt @@ -0,0 +1,23 @@ +Maxim Integrated SPI-based USB 2.0 host controller MAX3421E + +Required properties: + - compatible: Should be "maxim,max3421" + - spi-max-frequency: maximum frequency for this device must not exceed 26 MHz. + - reg: chip select number to which this device is connected. + - maxim,vbus-en-pin: <GPOUTx ACTIVE_LEVEL> + GPOUTx is the number (1-8) of the GPOUT pin of MAX3421E to drive Vbus. + ACTIVE_LEVEL is 0 or 1. + - interrupts: the interrupt line description for the interrupt controller. + The driver configures MAX3421E for active low level triggered interrupts, + configure your interrupt line accordingly. + +Example: + + usb@0 { + compatible = "maxim,max3421"; + reg = <0>; + maxim,vbus-en-pin = <3 1>; + spi-max-frequency = <26000000>; + interrupt-parent = <&PIC>; + interrupts = <42>; + }; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt new file mode 100644 index 000000000..266c2d917 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt @@ -0,0 +1,120 @@ +MT8173 xHCI + +The device node for Mediatek SOC USB3.0 host controller + +There are two scenarios: the first one only supports xHCI driver; +the second one supports dual-role mode, and the host is based on xHCI +driver. Take account of backward compatibility, we divide bindings +into two parts. + +1st: only supports xHCI driver +------------------------------------------------------------------------ + +Required properties: + - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", + soc-model is the name of SoC, such as mt8173, mt2712 etc, when using + "mediatek,mtk-xhci" compatible string, you need SoC specific ones in + addition, one of: + - "mediatek,mt8173-xhci" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control + - interrupts : interrupt used by the controller + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain + "sys_ck": controller clock used by normal mode, + the following ones are optional: + "ref_ck": reference clock used by low power mode etc, + "mcu_ck": mcu_bus clock for register access, + "dma_ck": dma_bus clock for data transfer by DMA + + - phys : see usb-hcd.txt in the current directory + +Optional properties: + - wakeup-source : enable USB remote wakeup; + - mediatek,syscon-wakeup : phandle to syscon used to access the register + of the USB wakeup glue layer between xHCI and SPM; it depends on + "wakeup-source", and has two arguments: + - the first one : register base address of the glue layer in syscon; + - the second one : hardware version of the glue layer + - 1 : used by mt8173 etc + - 2 : used by mt2712 etc + - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc; + - vbus-supply : reference to the VBUS regulator; + - usb3-lpm-capable : supports USB3.0 LPM + - pinctrl-names : a pinctrl state named "default" must be defined + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + - imod-interval-ns: default interrupt moderation interval is 5000ns + +additionally the properties from usb-hcd.txt (in the current directory) are +supported. + +Example: +usb30: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>, + <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_ck", "ref_ck"; + phys = <&phy_port0 PHY_TYPE_USB3>, + <&phy_port1 PHY_TYPE_USB2>; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p1_vbus>; + usb3-lpm-capable; + mediatek,syscon-wakeup = <&pericfg 0x400 1>; + wakeup-source; + imod-interval-ns = <10000>; +}; + +2nd: dual-role mode with xHCI driver +------------------------------------------------------------------------ + +In the case, xhci is added as subnode to mtu3. An example and the DT binding +details of mtu3 can be found in: +Documentation/devicetree/bindings/usb/mediatek,mtu3.txt + +Required properties: + - compatible : should be "mediatek,<soc-model>-xhci", "mediatek,mtk-xhci", + soc-model is the name of SoC, such as mt8173, mt2712 etc, when using + "mediatek,mtk-xhci" compatible string, you need SoC specific ones in + addition, one of: + - "mediatek,mt8173-xhci" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for xHCI MAC + - interrupts : interrupt used by the host controller + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain "sys_ck", and the following ones are optional: + "ref_ck", "mcu_ck" and "dma_ck" + +Optional properties: + - vbus-supply : reference to the VBUS regulator; + - usb3-lpm-capable : supports USB3.0 LPM + +Example: +usb30: usb@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + usb3-lpm-capable; +}; diff --git a/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt new file mode 100644 index 000000000..3382b5cb4 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/mediatek,mtu3.txt @@ -0,0 +1,98 @@ +The device node for Mediatek USB3.0 DRD controller + +Required properties: + - compatible : should be "mediatek,<soc-model>-mtu3", "mediatek,mtu3", + soc-model is the name of SoC, such as mt8173, mt2712 etc, + when using "mediatek,mtu3" compatible string, you need SoC specific + ones in addition, one of: + - "mediatek,mt8173-mtu3" + - reg : specifies physical base address and size of the registers + - reg-names: should be "mac" for device IP and "ippc" for IP port control + - interrupts : interrupt used by the device IP + - power-domains : a phandle to USB power domain node to control USB's + mtcmos + - vusb33-supply : regulator of USB avdd3.3v + - clocks : a list of phandle + clock-specifier pairs, one for each + entry in clock-names + - clock-names : must contain "sys_ck" for clock of controller, + the following clocks are optional: + "ref_ck", "mcu_ck" and "dam_ck"; + - phys : see usb-hcd.txt in the current directory + - dr_mode : should be one of "host", "peripheral" or "otg", + refer to usb/generic.txt + +Optional properties: + - #address-cells, #size-cells : should be '2' if the device has sub-nodes + with 'reg' property + - ranges : allows valid 1:1 translation between child's address space and + parent's address space + - extcon : external connector for vbus and idpin changes detection, needed + when supports dual-role mode. + - vbus-supply : reference to the VBUS regulator, needed when supports + dual-role mode. + - pinctrl-names : a pinctrl state named "default" is optional, and need be + defined if auto drd switch is enabled, that means the property dr_mode + is set as "otg", and meanwhile the property "mediatek,enable-manual-drd" + is not set. + - pinctrl-0 : pin control group + See: Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt + + - maximum-speed : valid arguments are "super-speed", "high-speed" and + "full-speed"; refer to usb/generic.txt + - enable-manual-drd : supports manual dual-role switch via debugfs; usually + used when receptacle is TYPE-A and also wants to support dual-role + mode. + - wakeup-source: enable USB remote wakeup of host mode. + - mediatek,syscon-wakeup : phandle to syscon used to access the register + of the USB wakeup glue layer between SSUSB and SPM; it depends on + "wakeup-source", and has two arguments: + - the first one : register base address of the glue layer in syscon; + - the second one : hardware version of the glue layer + - 1 : used by mt8173 etc + - 2 : used by mt2712 etc + - mediatek,u3p-dis-msk : mask to disable u3ports, bit0 for u3port0, + bit1 for u3port1, ... etc; + +additionally the properties from usb-hcd.txt (in the current directory) are +supported. + +Sub-nodes: +The xhci should be added as subnode to mtu3 as shown in the following example +if host mode is enabled. The DT binding details of xhci can be found in: +Documentation/devicetree/bindings/usb/mediatek,mtk-xhci.txt + +Example: +ssusb: usb@11271000 { + compatible = "mediatek,mt8173-mtu3"; + reg = <0 0x11271000 0 0x3000>, + <0 0x11280700 0 0x0100>; + reg-names = "mac", "ippc"; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>; + phys = <&phy_port0 PHY_TYPE_USB3>, + <&phy_port1 PHY_TYPE_USB2>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>, + <&pericfg CLK_PERI_USB0>, + <&pericfg CLK_PERI_USB1>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + vbus-supply = <&usb_p0_vbus>; + extcon = <&extcon_usb>; + dr_mode = "otg"; + wakeup-source; + mediatek,syscon-wakeup = <&pericfg 0x400 1>; + #address-cells = <2>; + #size-cells = <2>; + ranges; + + usb_host: xhci@11270000 { + compatible = "mediatek,mt8173-xhci"; + reg = <0 0x11270000 0 0x1000>; + reg-names = "mac"; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>; + clocks = <&topckgen CLK_TOP_USB30_SEL>, <&clk26m>; + clock-names = "sys_ck", "ref_ck"; + vusb33-supply = <&mt6397_vusb_reg>; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/msm-hsusb.txt b/Documentation/devicetree/bindings/usb/msm-hsusb.txt new file mode 100644 index 000000000..8654a3ec2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/msm-hsusb.txt @@ -0,0 +1,110 @@ +MSM SoC HSUSB controllers + +EHCI + +Required properties: +- compatible: Should contain "qcom,ehci-host" +- regs: offset and length of the register set in the memory map +- usb-phy: phandle for the PHY device + +Example EHCI controller device node: + + ehci: ehci@f9a55000 { + compatible = "qcom,ehci-host"; + reg = <0xf9a55000 0x400>; + usb-phy = <&usb_otg>; + }; + +USB PHY with optional OTG: + +Required properties: +- compatible: Should contain: + "qcom,usb-otg-ci" for chipsets with ChipIdea 45nm PHY + "qcom,usb-otg-snps" for chipsets with Synopsys 28nm PHY + +- regs: Offset and length of the register set in the memory map +- interrupts: interrupt-specifier for the OTG interrupt. + +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "phy" USB PHY reference clock + "core" Protocol engine clock + "iface" Interface bus clock + "alt_core" Protocol engine clock for targets with asynchronous + reset methodology. (optional) + +- vdccx-supply: phandle to the regulator for the vdd supply for + digital circuit operation. +- v1p8-supply: phandle to the regulator for the 1.8V supply +- v3p3-supply: phandle to the regulator for the 3.3V supply + +- resets: A list of phandle + reset-specifier pairs for the + resets listed in reset-names +- reset-names: Should contain the following: + "phy" USB PHY controller reset + "link" USB LINK controller reset + +- qcom,otg-control: OTG control (VBUS and ID notifications) can be one of + 1 - PHY control + 2 - PMIC control + +Optional properties: +- dr_mode: One of "host", "peripheral" or "otg". Defaults to "otg" + +- switch-gpio: A phandle + gpio-specifier pair. Some boards are using Dual + SPDT USB Switch, witch is cotrolled by GPIO to de/multiplex + D+/D- USB lines between connectors. + +- qcom,phy-init-sequence: PHY configuration sequence values. This is related to Device + Mode Eye Diagram test. Start address at which these values will be + written is ULPI_EXT_VENDOR_SPECIFIC. Value of -1 is reserved as + "do not overwrite default value at this address". + For example: qcom,phy-init-sequence = < -1 0x63 >; + Will update only value at address ULPI_EXT_VENDOR_SPECIFIC + 1. + +- qcom,phy-num: Select number of pyco-phy to use, can be one of + 0 - PHY one, default + 1 - Second PHY + Some platforms may have configuration to allow USB + controller work with any of the two HSPHYs present. + +- qcom,vdd-levels: This property must be a list of three integer values + (no, min, max) where each value represents either a voltage + in microvolts or a value corresponding to voltage corner. + +- qcom,manual-pullup: If present, vbus is not routed to USB controller/phy + and controller driver therefore enables pull-up explicitly + before starting controller using usbcmd run/stop bit. + +- extcon: phandles to external connector devices. First phandle + should point to external connector, which provide "USB" + cable events, the second should point to external connector + device, which provide "USB-HOST" cable events. If one of + the external connector devices is not required empty <0> + phandle should be specified. + +Example HSUSB OTG controller device node: + + usb@f9a55000 { + compatible = "qcom,usb-otg-snps"; + reg = <0xf9a55000 0x400>; + interrupts = <0 134 0>; + dr_mode = "peripheral"; + + clocks = <&gcc GCC_XO_CLK>, <&gcc GCC_USB_HS_SYSTEM_CLK>, + <&gcc GCC_USB_HS_AHB_CLK>; + + clock-names = "phy", "core", "iface"; + + vddcx-supply = <&pm8841_s2_corner>; + v1p8-supply = <&pm8941_l6>; + v3p3-supply = <&pm8941_l24>; + + resets = <&gcc GCC_USB2A_PHY_BCR>, <&gcc GCC_USB_HS_BCR>; + reset-names = "phy", "link"; + + qcom,otg-control = <1>; + qcom,phy-init-sequence = < -1 0x63 >; + qcom,vdd-levels = <1 5 7>; + }; diff --git a/Documentation/devicetree/bindings/usb/npcm7xx-usb.txt b/Documentation/devicetree/bindings/usb/npcm7xx-usb.txt new file mode 100644 index 000000000..5a0f1f14f --- /dev/null +++ b/Documentation/devicetree/bindings/usb/npcm7xx-usb.txt @@ -0,0 +1,18 @@ +Nuvoton NPCM7XX SoC USB controllers: +----------------------------- + +EHCI: +----- + +Required properties: +- compatible: "nuvoton,npcm750-ehci" +- interrupts: Should contain the EHCI interrupt +- reg: Physical address and length of the register set for the device + +Example: + + ehci1: usb@f0806000 { + compatible = "nuvoton,npcm750-ehci"; + reg = <0xf0806000 0x1000>; + interrupts = <0 61 4>; + }; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt new file mode 100644 index 000000000..3eee9e505 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra124-xusb.txt @@ -0,0 +1,120 @@ +NVIDIA Tegra xHCI controller +============================ + +The Tegra xHCI controller supports both USB2 and USB3 interfaces exposed by +the Tegra XUSB pad controller. + +Required properties: +-------------------- +- compatible: Must be: + - Tegra124: "nvidia,tegra124-xusb" + - Tegra132: "nvidia,tegra132-xusb", "nvidia,tegra124-xusb" + - Tegra210: "nvidia,tegra210-xusb" +- reg: Must contain the base and length of the xHCI host registers, XUSB FPCI + registers and XUSB IPFS registers. +- reg-names: Must contain the following entries: + - "hcd" + - "fpci" + - "ipfs" +- interrupts: Must contain the xHCI host interrupt and the mailbox interrupt. +- clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - xusb_host + - xusb_host_src + - xusb_falcon_src + - xusb_ss + - xusb_ss_src + - xusb_ss_div2 + - xusb_hs_src + - xusb_fs_src + - pll_u_480m + - clk_m + - pll_e +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - xusb_host + - xusb_ss + - xusb_src + Note that xusb_src is the shared reset for xusb_{ss,hs,fs,falcon,host}_src. +- nvidia,xusb-padctl: phandle to the XUSB pad controller that is used to + configure the USB pads used by the XHCI controller + +For Tegra124 and Tegra132: +- avddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- dvddio-pex-supply: PCIe/USB3 digital logic power supply. Must supply 1.05 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-erefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- avdd-usb-ss-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-usb-ss-supply: High-voltage PCIe/USB3 power supply. Must supply 3.3 V. +- hvdd-usb-ss-pll-e-supply: High-voltage PLLE power supply. Must supply 3.3 V. + +For Tegra210: +- dvddio-pex-supply: PCIe/USB3 analog logic power supply. Must supply 1.05 V. +- hvddio-pex-supply: High-voltage PCIe/USB3 power supply. Must supply 1.8 V. +- avdd-usb-supply: USB controller power supply. Must supply 3.3 V. +- avdd-pll-utmip-supply: UTMI PLL power supply. Must supply 1.8 V. +- avdd-pll-uerefe-supply: PLLE reference PLL power supply. Must supply 1.05 V. +- dvdd-pex-pll-supply: PCIe/USB3 PLL power supply. Must supply 1.05 V. +- hvdd-pex-pll-e-supply: High-voltage PLLE power supply. Must supply 1.8 V. + +Optional properties: +-------------------- +- phys: Must contain an entry for each entry in phy-names. + See ../phy/phy-bindings.txt for details. +- phy-names: Should include an entry for each PHY used by the controller. The + following PHYs are available: + - Tegra124: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra132: usb2-0, usb2-1, usb2-2, hsic-0, hsic-1, usb3-0, usb3-1 + - Tegra210: usb2-0, usb2-1, usb2-2, usb2-3, hsic-0, usb3-0, usb3-1, usb3-2, + usb3-3 + +Example: +-------- + + usb@0,70090000 { + compatible = "nvidia,tegra124-xusb"; + reg = <0x0 0x70090000 0x0 0x8000>, + <0x0 0x70098000 0x0 0x1000>, + <0x0 0x70099000 0x0 0x1000>; + reg-names = "hcd", "fpci", "ipfs"; + + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; + + clocks = <&tegra_car TEGRA124_CLK_XUSB_HOST>, + <&tegra_car TEGRA124_CLK_XUSB_HOST_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FALCON_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_SS>, + <&tegra_car TEGRA124_CLK_XUSB_SS_DIV2>, + <&tegra_car TEGRA124_CLK_XUSB_SS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_HS_SRC>, + <&tegra_car TEGRA124_CLK_XUSB_FS_SRC>, + <&tegra_car TEGRA124_CLK_PLL_U_480M>, + <&tegra_car TEGRA124_CLK_CLK_M>, + <&tegra_car TEGRA124_CLK_PLL_E>; + clock-names = "xusb_host", "xusb_host_src", "xusb_falcon_src", + "xusb_ss", "xusb_ss_div2", "xusb_ss_src", + "xusb_hs_src", "xusb_fs_src", "pll_u_480m", + "clk_m", "pll_e"; + resets = <&tegra_car 89>, <&tegra_car 156>, <&tegra_car 143>; + reset-names = "xusb_host", "xusb_ss", "xusb_src"; + + nvidia,xusb-padctl = <&padctl>; + + phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* mini-PCIe USB */ + <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* USB A */ + <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>; /* USB A */ + phy-names = "usb2-1", "usb2-2", "usb3-0"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-usb-supply = <&vdd_3v3_lp0>; + avdd-pll-utmip-supply = <&vddio_1v8>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + avdd-usb-ss-pll-supply = <&vdd_1v05_run>; + hvdd-usb-ss-supply = <&vdd_3v3_lp0>; + hvdd-usb-ss-pll-e-supply = <&vdd_3v3_lp0>; + }; diff --git a/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt new file mode 100644 index 000000000..f60785f73 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/nvidia,tegra20-ehci.txt @@ -0,0 +1,23 @@ +Tegra SOC USB controllers + +The device node for a USB controller that is part of a Tegra +SOC is as described in the document "Open Firmware Recommended +Practice : Universal Serial Bus" with the following modifications +and additions : + +Required properties : + - compatible : For Tegra20, must contain "nvidia,tegra20-ehci". + For Tegra30, must contain "nvidia,tegra30-ehci". Otherwise, must contain + "nvidia,<chip>-ehci" plus at least one of the above, where <chip> is + tegra114, tegra124, tegra132, or tegra210. + - nvidia,phy : phandle of the PHY that the controller is connected to. + - clocks : Must contain one entry, for the module clock. + See ../clocks/clock-bindings.txt for details. + - resets : Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. + - reset-names : Must include the following entries: + - usb + +Optional properties: + - nvidia,needs-double-reset : boolean is to be set for some of the Tegra20 + USB ports, which need reset twice due to hardware issues. diff --git a/Documentation/devicetree/bindings/usb/octeon-usb.txt b/Documentation/devicetree/bindings/usb/octeon-usb.txt new file mode 100644 index 000000000..205c8d24d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/octeon-usb.txt @@ -0,0 +1,62 @@ +OCTEON/OCTEON+ USB BLOCK + +1) Main node + + Required properties: + + - compatible: must be "cavium,octeon-5750-usbn" + + - reg: specifies the physical base address of the USBN block and + the length of the memory mapped region. + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 2. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 2. + + - ranges: specifies the translation between child address space and parent + address space. + + - clock-frequency: speed of the USB reference clock. Allowed values are + 12000000, 24000000 or 48000000. + + - cavium,refclk-type: type of the USB reference clock. Allowed values are + "crystal" or "external". + + - refclk-frequency: deprecated, use "clock-frequency". + + - refclk-type: deprecated, use "cavium,refclk-type". + +2) Child node + + The main node must have one child node which describes the built-in + USB controller. + + Required properties: + + - compatible: must be "cavium,octeon-5750-usbc" + + - reg: specifies the physical base address of the USBC block and + the length of the memory mapped region. + + - interrupts: specifies the interrupt number for the USB controller. + +3) Example: + + usbn: usbn@1180068000000 { + compatible = "cavium,octeon-5750-usbn"; + reg = <0x11800 0x68000000 0x0 0x1000>; + ranges; /* Direct mapping */ + #address-cells = <2>; + #size-cells = <2>; + clock-frequency = <12000000>; + cavium,refclk-type = "crystal"; + + usbc@16f0010000000 { + compatible = "cavium,octeon-5750-usbc"; + reg = <0x16f00 0x10000000 0x0 0x80000>; + interrupts = <0 56>; + }; + }; + diff --git a/Documentation/devicetree/bindings/usb/ohci-da8xx.txt b/Documentation/devicetree/bindings/usb/ohci-da8xx.txt new file mode 100644 index 000000000..24a826d50 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-da8xx.txt @@ -0,0 +1,23 @@ +DA8XX USB OHCI controller + +Required properties: + + - compatible: Should be "ti,da830-ohci" + - reg: Should contain one register range i.e. start and length + - interrupts: Description of the interrupt line + - phys: Phandle for the PHY device + - phy-names: Should be "usb-phy" + +Optional properties: + - vbus-supply: phandle of regulator that controls vbus power / over-current + +Example: + +ohci: usb@225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + vbus-supply = <®_usb_ohci>; +}; diff --git a/Documentation/devicetree/bindings/usb/ohci-nxp.txt b/Documentation/devicetree/bindings/usb/ohci-nxp.txt new file mode 100644 index 000000000..71e28c101 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-nxp.txt @@ -0,0 +1,24 @@ +* OHCI controller, NXP ohci-nxp variant + +Required properties: +- compatible: must be "nxp,ohci-nxp" +- reg: physical base address of the controller and length of memory mapped + region. +- interrupts: The OHCI interrupt +- transceiver: phandle of the associated ISP1301 device - this is necessary for + the UDC controller for connecting to the USB physical layer + +Example (LPC32xx): + + isp1301: usb-transceiver@2c { + compatible = "nxp,isp1301"; + reg = <0x2c>; + }; + + ohci@31020000 { + compatible = "nxp,ohci-nxp"; + reg = <0x31020000 0x300>; + interrupt-parent = <&mic>; + interrupts = <0x3b 0>; + transceiver = <&isp1301>; + }; diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt new file mode 100644 index 000000000..ce8c47cff --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt @@ -0,0 +1,15 @@ +OMAP HS USB OHCI controller (OMAP3 and later) + +Required properties: + +- compatible: should be "ti,ohci-omap3" +- reg: should contain one register range i.e. start and length +- interrupts: description of the interrupt line + +Example for OMAP4: + +usbhsohci: ohci@4a064800 { + compatible = "ti,ohci-omap3"; + reg = <0x4a064800 0x400>; + interrupts = <0 76 0x4>; +}; diff --git a/Documentation/devicetree/bindings/usb/ohci-st.txt b/Documentation/devicetree/bindings/usb/ohci-st.txt new file mode 100644 index 000000000..44c998c16 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ohci-st.txt @@ -0,0 +1,36 @@ +ST USB OHCI controller + +Required properties: + + - compatible : must be "st,st-ohci-300x" + - reg : physical base addresses of the controller and length of memory mapped + region + - interrupts : one OHCI controller interrupt should be described here + - clocks : phandle list of usb clocks + - clock-names : should be "ic" for interconnect clock and "clk48" +See: Documentation/devicetree/bindings/clock/clock-bindings.txt + + - phys : phandle for the PHY device + - phy-names : should be "usb" + + - resets : phandle to the powerdown and reset controller for the USB IP + - reset-names : should be "power" and "softreset". +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + + ohci0: usb@fe1ffc00 { + compatible = "st,st-ohci-300x"; + reg = <0xfe1ffc00 0x100>; + interrupts = <GIC_SPI 149 IRQ_TYPE_NONE>; + clocks = <&clk_s_a1_ls 0>, + <&clockgen_b0 0>; + clock-names = "ic", "clk48"; + phys = <&usb2_phy>; + phy-names = "usb"; + + resets = <&powerdown STIH416_USB0_POWERDOWN>, + <&softreset STIH416_USB0_SOFTRESET>; + reset-names = "power", "softreset"; + }; diff --git a/Documentation/devicetree/bindings/usb/omap-usb.txt b/Documentation/devicetree/bindings/usb/omap-usb.txt new file mode 100644 index 000000000..38d9bb850 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/omap-usb.txt @@ -0,0 +1,80 @@ +OMAP GLUE AND OTHER OMAP SPECIFIC COMPONENTS + +OMAP MUSB GLUE + - compatible : Should be "ti,omap4-musb" or "ti,omap3-musb" + - ti,hwmods : must be "usb_otg_hs" + - multipoint : Should be "1" indicating the musb controller supports + multipoint. This is a MUSB configuration-specific setting. + - num-eps : Specifies the number of endpoints. This is also a + MUSB configuration-specific setting. Should be set to "16" + - ram-bits : Specifies the ram address size. Should be set to "12" + - interface-type : This is a board specific setting to describe the type of + interface between the controller and the phy. It should be "0" or "1" + specifying ULPI and UTMI respectively. + - mode : Should be "3" to represent OTG. "1" signifies HOST and "2" + represents PERIPHERAL. + - power : Should be "50". This signifies the controller can supply up to + 100mA when operating in host mode. + - usb-phy : the phandle for the PHY device + - phys : the phandle for the PHY device (used by generic PHY framework) + - phy-names : the names of the PHY corresponding to the PHYs present in the + *phy* phandle. + +Optional properties: + - ctrl-module : phandle of the control module this glue uses to write to + mailbox + +SOC specific device node entry +usb_otg_hs: usb_otg_hs@4a0ab000 { + compatible = "ti,omap4-musb"; + ti,hwmods = "usb_otg_hs"; + multipoint = <1>; + num-eps = <16>; + ram-bits = <12>; + ctrl-module = <&omap_control_usb>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; +}; + +Board specific device node entry +&usb_otg_hs { + interface-type = <1>; + mode = <3>; + power = <50>; +}; + +OMAP DWC3 GLUE + - compatible : Should be + * "ti,dwc3" for OMAP5 and DRA7 + * "ti,am437x-dwc3" for AM437x + - ti,hwmods : Should be "usb_otg_ss" + - reg : Address and length of the register set for the device. + - interrupts : The irq number of this device that is used to interrupt the + MPU + - #address-cells, #size-cells : Must be present if the device has sub-nodes + - utmi-mode : controls the source of UTMI/PIPE status for VBUS and OTG ID. + It should be set to "1" for HW mode and "2" for SW mode. + - ranges: the child address space are mapped 1:1 onto the parent address space + +Optional Properties: + - extcon : phandle for the extcon device omap dwc3 uses to detect + connect/disconnect events. + - vbus-supply : phandle to the regulator device tree node if needed. + +Sub-nodes: +The dwc3 core should be added as subnode to omap dwc3 glue. +- dwc3 : + The binding details of dwc3 can be found in: + Documentation/devicetree/bindings/usb/dwc3.txt + +omap_dwc3 { + compatible = "ti,dwc3"; + ti,hwmods = "usb_otg_ss"; + reg = <0x4a020000 0x1ff>; + interrupts = <0 93 4>; + #address-cells = <1>; + #size-cells = <1>; + utmi-mode = <2>; + ranges; +}; + diff --git a/Documentation/devicetree/bindings/usb/pxa-usb.txt b/Documentation/devicetree/bindings/usb/pxa-usb.txt new file mode 100644 index 000000000..9c331799b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/pxa-usb.txt @@ -0,0 +1,53 @@ +PXA USB controllers + +OHCI + +Required properties: + - compatible: Should be "marvell,pxa-ohci" for USB controllers + used in host mode. + +Optional properties: + - "marvell,enable-port1", "marvell,enable-port2", "marvell,enable-port3" + If present, enables the appropriate USB port of the controller. + - "marvell,port-mode" selects the mode of the ports: + 1 = PMM_NPS_MODE + 2 = PMM_GLOBAL_MODE + 3 = PMM_PERPORT_MODE + - "marvell,power-sense-low" - power sense pin is low-active. + - "marvell,power-control-low" - power control pin is low-active. + - "marvell,no-oc-protection" - disable over-current protection. + - "marvell,oc-mode-perport" - enable per-port over-current protection. + - "marvell,power_on_delay" Power On to Power Good time - in ms. + +Example: + + usb0: ohci@4c000000 { + compatible = "marvell,pxa-ohci", "usb-ohci"; + reg = <0x4c000000 0x100000>; + interrupts = <18>; + marvell,enable-port1; + marvell,port-mode = <2>; /* PMM_GLOBAL_MODE */ + }; + +UDC + +Required properties: + - compatible: Should be "marvell,pxa270-udc" for USB controllers + used in device mode. + - reg: usb device MMIO address space + - interrupts: single interrupt generated by the UDC IP + - clocks: input clock of the UDC IP (see clock-bindings.txt) + +Optional properties: + - gpios: + - gpio activated to control the USB D+ pullup (see gpio.txt) + +Example: + + pxa27x_udc: udc@40600000 { + compatible = "marvell,pxa270-udc"; + reg = <0x40600000 0x10000>; + interrupts = <11>; + clocks = <&pxa2xx_clks 11>; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; diff --git a/Documentation/devicetree/bindings/usb/qcom,dwc3.txt b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt new file mode 100644 index 000000000..95afdcf3c --- /dev/null +++ b/Documentation/devicetree/bindings/usb/qcom,dwc3.txt @@ -0,0 +1,103 @@ +Qualcomm SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: Compatible list, contains + "qcom,dwc3" + "qcom,msm8996-dwc3" for msm8996 SOC. + "qcom,sdm845-dwc3" for sdm845 SOC. +- reg: Offset and length of register set for QSCRATCH wrapper +- power-domains: specifies a phandle to PM domain provider node +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "core" Master/Core clock, have to be >= 125 MHz for SS + operation and >= 60MHz for HS operation + "mock_utmi" Mock utmi clock needed for ITP/SOF generation in + host mode. Its frequency should be 19.2MHz. + "sleep" Sleep clock, used for wakeup when USB3 core goes + into low power mode (U3). + +Optional clocks: + "iface" System bus AXI clock. + Not present on "qcom,msm8996-dwc3" compatible. + "cfg_noc" System Config NOC clock. + Not present on "qcom,msm8996-dwc3" compatible. +- assigned-clocks: Should be: + MOCK_UTMI_CLK + MASTER_CLK +- assigned-clock-rates: Should be: + 19.2Mhz (192000000) for MOCK_UTMI_CLK + >=125Mhz (125000000) for MASTER_CLK in SS mode + >=60Mhz (60000000) for MASTER_CLK in HS mode + +Optional properties: +- resets: Phandle to reset control that resets core and wrapper. +- interrupts: specifies interrupts from controller wrapper used + to wakeup from low power/susepnd state. Must contain + one or more entry for interrupt-names property +- interrupt-names: Must include the following entries: + - "hs_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB2 bus + - "ss_phy_irq": The interrupt that is asserted when a + wakeup event is received on USB3 bus + - "dm_hs_phy_irq" and "dp_hs_phy_irq": Separate + interrupts for any wakeup event on DM and DP lines +- qcom,select-utmi-as-pipe-clk: if present, disable USB3 pipe_clk requirement. + Used when dwc3 operates without SSPHY and only + HS/FS/LS modes are supported. + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/qcom-qmp-phy.txt - USB3 QMP PHY +Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt - USB2 QUSB2 PHY + +Example device nodes: + + hs_phy: phy@100f8800 { + compatible = "qcom,qusb2-v2-phy"; + ... + }; + + ss_phy: phy@100f8830 { + compatible = "qcom,qmp-v3-usb3-phy"; + ... + }; + + usb3_0: usb30@a6f8800 { + compatible = "qcom,dwc3"; + reg = <0xa6f8800 0x400>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + interrupts = <0 131 0>, <0 486 0>, <0 488 0>, <0 489 0>; + interrupt-names = "hs_phy_irq", "ss_phy_irq", + "dm_hs_phy_irq", "dp_hs_phy_irq"; + + clocks = <&gcc GCC_USB30_PRIM_MASTER_CLK>, + <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_SLEEP_CLK>; + clock-names = "core", "mock_utmi", "sleep"; + + assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, + <&gcc GCC_USB30_PRIM_MASTER_CLK>; + assigned-clock-rates = <19200000>, <133000000>; + + resets = <&gcc GCC_USB30_PRIM_BCR>; + reset-names = "core_reset"; + power-domains = <&gcc USB30_PRIM_GDSC>; + qcom,select-utmi-as-pipe-clk; + + dwc3@10000000 { + compatible = "snps,dwc3"; + reg = <0x10000000 0xcd00>; + interrupts = <0 205 0x4>; + phys = <&hs_phy>, <&ss_phy>; + phy-names = "usb2-phy", "usb3-phy"; + dr_mode = "host"; + }; + }; + diff --git a/Documentation/devicetree/bindings/usb/renesas_usb3.txt b/Documentation/devicetree/bindings/usb/renesas_usb3.txt new file mode 100644 index 000000000..2c071bb58 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/renesas_usb3.txt @@ -0,0 +1,38 @@ +Renesas Electronics USB3.0 Peripheral driver + +Required properties: + - compatible: Must contain one of the following: + - "renesas,r8a7795-usb3-peri" + - "renesas,r8a7796-usb3-peri" + - "renesas,r8a77965-usb3-peri" + - "renesas,rcar-gen3-usb3-peri" for a generic R-Car Gen3 compatible + device + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + + - reg: Base address and length of the register for the USB3.0 Peripheral + - interrupts: Interrupt specifier for the USB3.0 Peripheral + - clocks: clock phandle and specifier pair + +Optional properties: + - phys: phandle + phy specifier pair + - phy-names: must be "usb" + +Example of R-Car H3 ES1.x: + usb3_peri0: usb@ee020000 { + compatible = "renesas,r8a7795-usb3-peri", + "renesas,rcar-gen3-usb3-peri"; + reg = <0 0xee020000 0 0x400>; + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 328>; + }; + + usb3_peri1: usb@ee060000 { + compatible = "renesas,r8a7795-usb3-peri", + "renesas,rcar-gen3-usb3-peri"; + reg = <0 0xee060000 0 0x400>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 327>; + }; diff --git a/Documentation/devicetree/bindings/usb/renesas_usbhs.txt b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt new file mode 100644 index 000000000..43960faf5 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/renesas_usbhs.txt @@ -0,0 +1,46 @@ +Renesas Electronics USBHS driver + +Required properties: + - compatible: Must contain one or more of the following: + + - "renesas,usbhs-r8a7743" for r8a7743 (RZ/G1M) compatible device + - "renesas,usbhs-r8a7745" for r8a7745 (RZ/G1E) compatible device + - "renesas,usbhs-r8a7790" for r8a7790 (R-Car H2) compatible device + - "renesas,usbhs-r8a7791" for r8a7791 (R-Car M2-W) compatible device + - "renesas,usbhs-r8a7792" for r8a7792 (R-Car V2H) compatible device + - "renesas,usbhs-r8a7793" for r8a7793 (R-Car M2-N) compatible device + - "renesas,usbhs-r8a7794" for r8a7794 (R-Car E2) compatible device + - "renesas,usbhs-r8a7795" for r8a7795 (R-Car H3) compatible device + - "renesas,usbhs-r8a7796" for r8a7796 (R-Car M3-W) compatible device + - "renesas,usbhs-r8a77965" for r8a77965 (R-Car M3-N) compatible device + - "renesas,usbhs-r8a77995" for r8a77995 (R-Car D3) compatible device + - "renesas,usbhs-r7s72100" for r7s72100 (RZ/A1) compatible device + - "renesas,rcar-gen2-usbhs" for R-Car Gen2 or RZ/G1 compatible devices + - "renesas,rcar-gen3-usbhs" for R-Car Gen3 compatible device + - "renesas,rza1-usbhs" for RZ/A1 compatible device + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first followed + by the generic version. + + - reg: Base address and length of the register for the USBHS + - interrupts: Interrupt specifier for the USBHS + - clocks: A list of phandle + clock specifier pairs + +Optional properties: + - renesas,buswait: Integer to use BUSWAIT register + - renesas,enable-gpio: A gpio specifier to check GPIO determining if USB + function should be enabled + - phys: phandle + phy specifier pair + - phy-names: must be "usb" + - dmas: Must contain a list of references to DMA specifiers. + - dma-names : named "ch%d", where %d is the channel number ranging from zero + to the number of channels (DnFIFOs) minus one. + +Example: + usbhs: usb@e6590000 { + compatible = "renesas,usbhs-r8a7790", "renesas,rcar-gen2-usbhs"; + reg = <0 0xe6590000 0 0x100>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_HSUSB>; + }; diff --git a/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt new file mode 100644 index 000000000..d4cf53c07 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/richtek,rt1711h.txt @@ -0,0 +1,15 @@ +Richtek RT1711H TypeC PD Controller. + +Required properties: + - compatible : Must be "richtek,rt1711h". + - reg : Must be 0x4e, it's slave address of RT1711H. + - interrupts : <a b> where a is the interrupt number and b represents an + encoding of the sense and level information for the interrupt. + +Example : +rt1711h@4e { + compatible = "richtek,rt1711h"; + reg = <0x4e>; + interrupt-parent = <&gpio26>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; +}; diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt new file mode 100644 index 000000000..c8c4b00ec --- /dev/null +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt @@ -0,0 +1,56 @@ +Rockchip SuperSpeed DWC3 USB SoC controller + +Required properties: +- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC +- clocks: A list of phandle + clock-specifier pairs for the + clocks listed in clock-names +- clock-names: Should contain the following: + "ref_clk" Controller reference clk, have to be 24 MHz + "suspend_clk" Controller suspend clk, have to be 24 MHz or 32 KHz + "bus_clk" Master/Core clock, have to be >= 62.5 MHz for SS + operation and >= 30MHz for HS operation + "grf_clk" Controller grf clk + +Required child node: +A child node must exist to represent the core DWC3 IP block. The name of +the node is not important. The content of the node is defined in dwc3.txt. + +Phy documentation is provided in the following places: +Documentation/devicetree/bindings/phy/phy-rockchip-inno-usb2.txt - USB2.0 PHY +Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt - Type-C PHY + +Example device nodes: + + usbdrd3_0: usb@fe800000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG0_REF>, <&cru SCLK_USB3OTG0_SUSPEND>, + <&cru ACLK_USB3OTG0>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + usbdrd_dwc3_0: dwc3@fe800000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe800000 0x0 0x100000>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + }; + }; + + usbdrd3_1: usb@fe900000 { + compatible = "rockchip,rk3399-dwc3"; + clocks = <&cru SCLK_USB3OTG1_REF>, <&cru SCLK_USB3OTG1_SUSPEND>, + <&cru ACLK_USB3OTG1>, <&cru ACLK_USB3_GRF>; + clock-names = "ref_clk", "suspend_clk", + "bus_clk", "grf_clk"; + #address-cells = <2>; + #size-cells = <2>; + ranges; + usbdrd_dwc3_1: dwc3@fe900000 { + compatible = "snps,dwc3"; + reg = <0x0 0xfe900000 0x0 0x100000>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; + dr_mode = "otg"; + }; + }; diff --git a/Documentation/devicetree/bindings/usb/s3c2410-usb.txt b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt new file mode 100644 index 000000000..e45b38ce2 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/s3c2410-usb.txt @@ -0,0 +1,22 @@ +Samsung S3C2410 and compatible SoC USB controller + +OHCI + +Required properties: + - compatible: should be "samsung,s3c2410-ohci" for USB host controller + - reg: address and lenght of the controller memory mapped region + - interrupts: interrupt number for the USB OHCI controller + - clocks: Should reference the bus and host clocks + - clock-names: Should contain two strings + "usb-bus-host" for the USB bus clock + "usb-host" for the USB host clock + +Example: + +usb0: ohci@49000000 { + compatible = "samsung,s3c2410-ohci"; + reg = <0x49000000 0x100>; + interrupts = <0 0 26 3>; + clocks = <&clocks UCLK>, <&clocks HCLK_USBH>; + clock-names = "usb-bus-host", "usb-host"; +}; diff --git a/Documentation/devicetree/bindings/usb/samsung-hsotg.txt b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt new file mode 100644 index 000000000..038863459 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/samsung-hsotg.txt @@ -0,0 +1,38 @@ +Samsung High Speed USB OTG controller +----------------------------- + +The Samsung HSOTG IP can be found on Samsung SoCs, from S3C6400 onwards. +It gives functionality of OTG-compliant USB 2.0 host and device with +support for USB 2.0 high-speed (480Mbps) and full-speed (12 Mbps) +operation. + +Currently only device mode is supported. + +Binding details +----- + +Required properties: +- compatible: "samsung,s3c6400-hsotg" should be used for all currently + supported SoC, +- interrupts: specifier of interrupt signal of interrupt controller, + according to bindings of interrupt controller, +- clocks: contains an array of clock specifiers: + - first entry: OTG clock +- clock-names: contains array of clock names: + - first entry: must be "otg" +- vusb_d-supply: phandle to voltage regulator of digital section, +- vusb_a-supply: phandle to voltage regulator of analog section. + +Example +----- + + hsotg@12480000 { + compatible = "samsung,s3c6400-hsotg"; + reg = <0x12480000 0x20000>; + interrupts = <0 71 0>; + clocks = <&clock 305>; + clock-names = "otg"; + vusb_d-supply = <&vusb_reg>; + vusb_a-supply = <&vusbdac_reg>; + }; + diff --git a/Documentation/devicetree/bindings/usb/spear-usb.txt b/Documentation/devicetree/bindings/usb/spear-usb.txt new file mode 100644 index 000000000..1dc91cc45 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/spear-usb.txt @@ -0,0 +1,35 @@ +ST SPEAr SoC USB controllers: +----------------------------- + +EHCI: +----- + +Required properties: +- compatible: "st,spear600-ehci" +- interrupts: Should contain the EHCI interrupt + +Example: + + ehci@e1800000 { + compatible = "st,spear600-ehci", "usb-ehci"; + reg = <0xe1800000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <27>; + }; + + +OHCI: +----- + +Required properties: +- compatible: "st,spear600-ohci" +- interrupts: Should contain the OHCI interrupt + +Example: + + ohci@e1900000 { + compatible = "st,spear600-ohci", "usb-ohci"; + reg = <0xe1800000 0x1000>; + interrupt-parent = <&vic1>; + interrupts = <26>; + }; diff --git a/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt new file mode 100644 index 000000000..17327a296 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/twlxxxx-usb.txt @@ -0,0 +1,43 @@ +USB COMPARATOR OF TWL CHIPS + +TWL6030 USB COMPARATOR + - compatible : Should be "ti,twl6030-usb" + - interrupts : Two interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts when + the controller has to act as host and the second interrupt number is the + usb interrupt number that raises VBUS interrupts when the controller has to + act as device + - usb-supply : phandle to the regulator device tree node. It should be vusb + if it is twl6030 or ldousb if it is twl6032 subclass. + +twl6030-usb { + compatible = "ti,twl6030-usb"; + interrupts = < 4 10 >; +}; + +Board specific device node entry +&twl6030-usb { + usb-supply = <&vusb>; +}; + +TWL4030 USB PHY AND COMPARATOR + - compatible : Should be "ti,twl4030-usb" + - interrupts : The interrupt numbers to the cpu should be specified. First + interrupt number is the otg interrupt number that raises ID interrupts + and VBUS interrupts. The second interrupt number is optional. + - <supply-name>-supply : phandle to the regulator device tree node. + <supply-name> should be vusb1v5, vusb1v8 and vusb3v1 + - usb_mode : The mode used by the phy to connect to the controller. "1" + specifies "ULPI" mode and "2" specifies "CEA2011_3PIN" mode. + +If a sibling node is compatible "ti,twl4030-bci", then it will find +this device and query it for USB power status. + +twl4030-usb { + compatible = "ti,twl4030-usb"; + interrupts = < 10 4 >; + usb1v5-supply = <&vusb1v5>; + usb1v8-supply = <&vusb1v8>; + usb3v1-supply = <&vusb3v1>; + usb_mode = <1>; +}; diff --git a/Documentation/devicetree/bindings/usb/typec-tcpci.txt b/Documentation/devicetree/bindings/usb/typec-tcpci.txt new file mode 100644 index 000000000..0dd1469e7 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/typec-tcpci.txt @@ -0,0 +1,49 @@ +TCPCI(Typec port cotroller interface) binding +--------------------------------------------- + +Required properties: +- compatible: should be set one of following: + - "nxp,ptn5110" for NXP USB PD TCPC PHY IC ptn5110. + +- reg: the i2c slave address of typec port controller device. +- interrupt-parent: the phandle to the interrupt controller which provides + the interrupt. +- interrupts: interrupt specification for tcpci alert. + +Required sub-node: +- connector: The "usb-c-connector" attached to the tcpci chip, the bindings + of connector node are specified in + Documentation/devicetree/bindings/connector/usb-connector.txt + +Example: + +ptn5110@50 { + compatible = "nxp,ptn5110"; + reg = <0x50>; + interrupt-parent = <&gpio3>; + interrupts = <3 IRQ_TYPE_LEVEL_LOW>; + + usb_con: connector { + compatible = "usb-c-connector"; + label = "USB-C"; + data-role = "dual"; + power-role = "dual"; + try-power-role = "sink"; + source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; + sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) + PDO_VAR(5000, 12000, 2000)>; + op-sink-microwatt = <10000000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@1 { + reg = <1>; + usb_con_ss: endpoint { + remote-endpoint = <&usb3_data_ss>; + }; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/udc-xilinx.txt b/Documentation/devicetree/bindings/usb/udc-xilinx.txt new file mode 100644 index 000000000..47b4e397a --- /dev/null +++ b/Documentation/devicetree/bindings/usb/udc-xilinx.txt @@ -0,0 +1,18 @@ +Xilinx USB2 device controller + +Required properties: +- compatible : Should be "xlnx,usb2-device-4.00.a" +- reg : Physical base address and size of the USB2 + device registers map. +- interrupts : Should contain single irq line of USB2 device + controller +- xlnx,has-builtin-dma : if DMA is included + +Example: + axi-usb2-device@42e00000 { + compatible = "xlnx,usb2-device-4.00.a"; + interrupts = <0x0 0x39 0x1>; + reg = <0x42e00000 0x10000>; + xlnx,has-builtin-dma; + }; + diff --git a/Documentation/devicetree/bindings/usb/ulpi.txt b/Documentation/devicetree/bindings/usb/ulpi.txt new file mode 100644 index 000000000..ca179dc4b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ulpi.txt @@ -0,0 +1,20 @@ +ULPI bus binding +---------------- + +Phys that are behind a ULPI connection can be described with the following +binding. The host controller shall have a "ulpi" named node as a child, and +that node shall have one enabled node underneath it representing the ulpi +device on the bus. + +EXAMPLE +------- + +usb { + compatible = "vendor,usb-controller"; + + ulpi { + phy { + compatible = "vendor,phy"; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-device.txt b/Documentation/devicetree/bindings/usb/usb-device.txt new file mode 100644 index 000000000..036be172b --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-device.txt @@ -0,0 +1,102 @@ +Generic USB Device Properties + +Usually, we only use device tree for hard wired USB device. +The reference binding doc is from: +http://www.devicetree.org/open-firmware/bindings/usb/usb-1_0.ps + +Four types of device-tree nodes are defined: "host-controller nodes" +representing USB host controllers, "device nodes" representing USB devices, +"interface nodes" representing USB interfaces and "combined nodes" +representing simple USB devices. + +A combined node shall be used instead of a device node and an interface node +for devices of class 0 or 9 (hub) with a single configuration and a single +interface. + +A "hub node" is a combined node or an interface node that represents a USB +hub. + + +Required properties for device nodes: +- compatible: "usbVID,PID", where VID is the vendor id and PID the product id. + The textual representation of VID and PID shall be in lower case hexadecimal + with leading zeroes suppressed. The other compatible strings from the above + standard binding could also be used, but a device adhering to this binding + may leave out all except for "usbVID,PID". +- reg: the number of the USB hub port or the USB host-controller port to which + this device is attached. The range is 1-255. + + +Required properties for device nodes with interface nodes: +- #address-cells: shall be 2 +- #size-cells: shall be 0 + + +Required properties for interface nodes: +- compatible: "usbifVID,PID.configCN.IN", where VID is the vendor id, PID is + the product id, CN is the configuration value and IN is the interface + number. The textual representation of VID, PID, CN and IN shall be in lower + case hexadecimal with leading zeroes suppressed. The other compatible + strings from the above standard binding could also be used, but a device + adhering to this binding may leave out all except for + "usbifVID,PID.configCN.IN". +- reg: the interface number and configuration value + +The configuration component is not included in the textual representation of +an interface-node unit address for configuration 1. + + +Required properties for combined nodes: +- compatible: "usbVID,PID", where VID is the vendor id and PID the product id. + The textual representation of VID and PID shall be in lower case hexadecimal + with leading zeroes suppressed. The other compatible strings from the above + standard binding could also be used, but a device adhering to this binding + may leave out all except for "usbVID,PID". +- reg: the number of the USB hub port or the USB host-controller port to which + this device is attached. The range is 1-255. + + +Required properties for hub nodes with device nodes: +- #address-cells: shall be 1 +- #size-cells: shall be 0 + + +Required properties for host-controller nodes with device nodes: +- #address-cells: shall be 1 +- #size-cells: shall be 0 + + +Example: + +&usb1 { /* host controller */ + #address-cells = <1>; + #size-cells = <0>; + + hub@1 { /* hub connected to port 1 */ + compatible = "usb5e3,608"; + reg = <1>; + }; + + device@2 { /* device connected to port 2 */ + compatible = "usb123,4567"; + reg = <2>; + }; + + device@3 { /* device connected to port 3 */ + compatible = "usb123,abcd"; + reg = <3>; + + #address-cells = <2>; + #size-cells = <0>; + + interface@0 { /* interface 0 of configuration 1 */ + compatible = "usbif123,abcd.config1.0"; + reg = <0 1>; + }; + + interface@0,2 { /* interface 0 of configuration 2 */ + compatible = "usbif123,abcd.config2.0"; + reg = <0 2>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/usb/usb-ehci.txt b/Documentation/devicetree/bindings/usb/usb-ehci.txt new file mode 100644 index 000000000..0f1b75386 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-ehci.txt @@ -0,0 +1,42 @@ +USB EHCI controllers + +Required properties: + - compatible : should be "generic-ehci". + - reg : should contain at least address and length of the standard EHCI + register set for the device. Optional platform-dependent registers + (debug-port or other) can be also specified here, but only after + definition of standard EHCI registers. + - interrupts : one EHCI interrupt should be described here. + +Optional properties: + - big-endian-regs : boolean, set this for hcds with big-endian registers + - big-endian-desc : boolean, set this for hcds with big-endian descriptors + - big-endian : boolean, for hcds with big-endian-regs + big-endian-desc + - needs-reset-on-resume : boolean, set this to force EHCI reset after resume + - has-transaction-translator : boolean, set this if EHCI have a Transaction + Translator built into the root hub. + - clocks : a list of phandle + clock specifier pairs + - phys : see usb-hcd.txt in the current directory + - resets : phandle + reset specifier pair + +additionally the properties from usb-hcd.txt (in the current directory) are +supported. + +Example (Sequoia 440EPx): + ehci@e0000300 { + compatible = "ibm,usb-ehci-440epx", "usb-ehci"; + interrupt-parent = <&UIC0>; + interrupts = <1a 4>; + reg = <0 e0000300 90 0 e0000390 70>; + big-endian; + }; + +Example (Allwinner sun4i A10 SoC): + ehci0: usb@1c14000 { + compatible = "allwinner,sun4i-a10-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <39>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-hcd.txt b/Documentation/devicetree/bindings/usb/usb-hcd.txt new file mode 100644 index 000000000..50529b838 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-hcd.txt @@ -0,0 +1,9 @@ +Generic USB HCD (Host Controller Device) Properties + +Optional properties: +- phys: a list of all USB PHYs on this HCD + +Example: + &usb1 { + phys = <&usb2_phy1>, <&usb3_phy1>; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt new file mode 100644 index 000000000..4dc6a8ee3 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-nop-xceiv.txt @@ -0,0 +1,43 @@ +USB NOP PHY + +Required properties: +- compatible: should be usb-nop-xceiv +- #phy-cells: Must be 0 + +Optional properties: +- clocks: phandle to the PHY clock. Use as per Documentation/devicetree + /bindings/clock/clock-bindings.txt + This property is required if clock-frequency is specified. + +- clock-names: Should be "main_clk" + +- clock-frequency: the clock frequency (in Hz) that the PHY clock must + be configured to. + +- vcc-supply: phandle to the regulator that provides power to the PHY. + +- reset-gpios: Should specify the GPIO for reset. + +- vbus-detect-gpio: should specify the GPIO detecting a VBus insertion + (see Documentation/devicetree/bindings/gpio/gpio.txt) +- vbus-regulator : should specifiy the regulator supplying current drawn from + the VBus line (see Documentation/devicetree/bindings/regulator/regulator.txt). + +Example: + + hsusb1_phy { + compatible = "usb-nop-xceiv"; + clock-frequency = <19200000>; + clocks = <&osc 0>; + clock-names = "main_clk"; + vcc-supply = <&hsusb1_vcc_regulator>; + reset-gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + vbus-detect-gpio = <&gpio2 13 GPIO_ACTIVE_HIGH>; + vbus-regulator = <&vbus_regulator>; + #phy-cells = <0>; + }; + +hsusb1_phy is a NOP USB PHY device that gets its clock from an oscillator +and expects that clock to be configured to 19.2MHz by the NOP PHY driver. +hsusb1_vcc_regulator provides power to the PHY and GPIO 7 controls RESET. +GPIO 13 detects VBus insertion, and accordingly notifies the vbus-regulator. diff --git a/Documentation/devicetree/bindings/usb/usb-ohci.txt b/Documentation/devicetree/bindings/usb/usb-ohci.txt new file mode 100644 index 000000000..a8d2103d1 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-ohci.txt @@ -0,0 +1,31 @@ +USB OHCI controllers + +Required properties: +- compatible : "generic-ohci" +- reg : ohci controller register range (address and length) +- interrupts : ohci controller interrupt + +Optional properties: +- big-endian-regs : boolean, set this for hcds with big-endian registers +- big-endian-desc : boolean, set this for hcds with big-endian descriptors +- big-endian : boolean, for hcds with big-endian-regs + big-endian-desc +- no-big-frame-no : boolean, set if frame_no lives in bits [15:0] of HCCA +- remote-wakeup-connected: remote wakeup is wired on the platform +- num-ports : u32, to override the detected port count +- clocks : a list of phandle + clock specifier pairs +- phys : see usb-hcd.txt in the current directory +- resets : a list of phandle + reset specifier pairs + +additionally the properties from usb-hcd.txt (in the current directory) are +supported. + +Example: + + ohci0: usb@1c14400 { + compatible = "allwinner,sun4i-a10-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <64>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + phy-names = "usb"; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-uhci.txt b/Documentation/devicetree/bindings/usb/usb-uhci.txt new file mode 100644 index 000000000..cc2e6f7d6 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-uhci.txt @@ -0,0 +1,18 @@ +Generic Platform UHCI Controller +----------------------------------------------------- + +Required properties: +- compatible : "generic-uhci" (deprecated: "platform-uhci") +- reg : Should contain 1 register ranges(address and length) +- interrupts : UHCI controller interrupt + +additionally the properties from usb-hcd.txt (in the current directory) are +supported. + +Example: + + uhci@d8007b00 { + compatible = "generic-uhci"; + reg = <0xd8007b00 0x200>; + interrupts = <43>; + }; diff --git a/Documentation/devicetree/bindings/usb/usb-xhci.txt b/Documentation/devicetree/bindings/usb/usb-xhci.txt new file mode 100644 index 000000000..ac4cd0d61 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb-xhci.txt @@ -0,0 +1,51 @@ +USB xHCI controllers + +Required properties: + - compatible: should be one or more of + + - "generic-xhci" for generic XHCI device + - "marvell,armada3700-xhci" for Armada 37xx SoCs + - "marvell,armada-375-xhci" for Armada 375 SoCs + - "marvell,armada-380-xhci" for Armada 38x SoCs + - "renesas,xhci-r8a7743" for r8a7743 SoC + - "renesas,xhci-r8a7790" for r8a7790 SoC + - "renesas,xhci-r8a7791" for r8a7791 SoC + - "renesas,xhci-r8a7793" for r8a7793 SoC + - "renesas,xhci-r8a7795" for r8a7795 SoC + - "renesas,xhci-r8a7796" for r8a7796 SoC + - "renesas,xhci-r8a77965" for r8a77965 SoC + - "renesas,xhci-r8a77990" for r8a77990 SoC + - "renesas,rcar-gen2-xhci" for a generic R-Car Gen2 or RZ/G1 compatible + device + - "renesas,rcar-gen3-xhci" for a generic R-Car Gen3 compatible device + - "xhci-platform" (deprecated) + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + + - reg: should contain address and length of the standard XHCI + register set for the device. + - interrupts: one XHCI interrupt should be described here. + +Optional properties: + - clocks: reference to the clocks + - clock-names: mandatory if there is a second clock, in this case + the name must be "core" for the first clock and "reg" for the + second one + - usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM + - usb3-lpm-capable: determines if platform is USB3 LPM capable + - quirk-broken-port-ped: set if the controller has broken port disable mechanism + - imod-interval-ns: default interrupt moderation interval is 5000ns + - phys : see usb-hcd.txt in the current directory + +additionally the properties from usb-hcd.txt (in the current directory) are +supported. + + +Example: + usb@f0931000 { + compatible = "generic-xhci"; + reg = <0xf0931000 0x8c8>; + interrupts = <0x0 0x4e 0x0>; + }; diff --git a/Documentation/devicetree/bindings/usb/usb251xb.txt b/Documentation/devicetree/bindings/usb/usb251xb.txt new file mode 100644 index 000000000..168ff819e --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb251xb.txt @@ -0,0 +1,84 @@ +Microchip USB 2.0 Hi-Speed Hub Controller + +The device node for the configuration of a Microchip USB251x/xBi USB 2.0 +Hi-Speed Controller. + +Required properties : + - compatible : Should be "microchip,usb251xb" or one of the specific types: + "microchip,usb2512b", "microchip,usb2512bi", "microchip,usb2513b", + "microchip,usb2513bi", "microchip,usb2514b", "microchip,usb2514bi", + "microchip,usb2517", "microchip,usb2517i" + - reg : I2C address on the selected bus (default is <0x2C>) + +Optional properties : + - reset-gpios : Should specify the gpio for hub reset + - skip-config : Skip Hub configuration, but only send the USB-Attach command + - vendor-id : Set USB Vendor ID of the hub (16 bit, default is 0x0424) + - product-id : Set USB Product ID of the hub (16 bit, default depends on type) + - device-id : Set USB Device ID of the hub (16 bit, default is 0x0bb3) + - language-id : Set USB Language ID (16 bit, default is 0x0000) + - manufacturer : Set USB Manufacturer string (max 31 characters long) + - product : Set USB Product string (max 31 characters long) + - serial : Set USB Serial string (max 31 characters long) + - {bus,self}-powered : selects between self- and bus-powered operation + (boolean, default is self-powered) + - disable-hi-speed : disable USB Hi-Speed support (boolean) + - {multi,single}-tt : selects between multi- and single-transaction-translator + (boolean, default is multi-tt) + - disable-eop : disable End of Packet generation in full-speed mode (boolean) + - {ganged,individual}-sensing : select over-current sense type in self-powered + mode (boolean, default is individual) + - {ganged,individual}-port-switching : select port power switching mode + (boolean, default is individual) + - dynamic-power-switching : enable auto-switching from self- to bus-powered + operation if the local power source is removed or unavailable (boolean) + - oc-delay-us : Delay time (in microseconds) for filtering the over-current + sense inputs. Valid values are 100, 4000, 8000 (default) and 16000. If + an invalid value is given, the default is used instead. + - compound-device : indicate the hub is part of a compound device (boolean) + - port-mapping-mode : enable port mapping mode (boolean) + - led-{usb,speed}-mode : led usb/speed indication mode selection + (boolean, default is speed mode) + - string-support : enable string descriptor support (required for manufacturer, + product and serial string configuration) + - non-removable-ports : Should specify the ports which have a non-removable + device connected. + - sp-disabled-ports : Specifies the ports which will be self-power disabled + - bp-disabled-ports : Specifies the ports which will be bus-power disabled + - sp-max-total-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry including a permanently + attached peripheral (range: 0 - 100000 uA, default 1000 uA) + - bp-max-total-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry including a permanently + attached peripheral (range: 0 - 510000 uA, default 100000 uA) + - sp-max-removable-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry excluding a permanently + attached peripheral (range: 0 - 100000 uA, default 1000 uA) + - bp-max-removable-current-microamp: Specifies max current consumed by the hub + from VBUS when operating in self-powered hub. It includes the hub + silicon along with all associated circuitry excluding a permanently + attached peripheral (range: 0 - 510000 uA, default 100000 uA) + - power-on-time-ms : Specifies the time it takes from the time the host + initiates the power-on sequence to a port until the port has adequate + power. The value is given in ms in a 0 - 510 range (default is 100ms). + +Examples: + usb2512b@2c { + compatible = "microchip,usb2512b"; + reg = <0x2c>; + reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + usb2514b@2c { + compatible = "microchip,usb2514b"; + reg = <0x2c>; + vendor-id = /bits/ 16 <0x0000>; + product-id = /bits/ 16 <0x0000>; + string-support; + manufacturer = "Foo"; + product = "Foo-Bar"; + serial = "1234567890A"; + }; diff --git a/Documentation/devicetree/bindings/usb/usb3503.txt b/Documentation/devicetree/bindings/usb/usb3503.txt new file mode 100644 index 000000000..057dd384d --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb3503.txt @@ -0,0 +1,39 @@ +SMSC USB3503 High-Speed Hub Controller + +Required properties: +- compatible: Should be "smsc,usb3503" or "smsc,usb3503a". + +Optional properties: +- reg: Specifies the i2c slave address, it is required and should be 0x08 + if I2C is used. +- connect-gpios: Should specify GPIO for connect. +- disabled-ports: Should specify the ports unused. + '1' or '2' or '3' are available for this property to describe the port + number. 1~3 property values are possible to be described. + Do not describe this property if all ports have to be enabled. +- intn-gpios: Should specify GPIO for interrupt. +- reset-gpios: Should specify GPIO for reset. +- initial-mode: Should specify initial mode. + (1 for HUB mode, 2 for STANDBY mode) +- refclk: Clock used for driving REFCLK signal (optional, if not provided + the driver assumes that clock signal is always available, its + rate is specified by REF_SEL pins and a value from the primary + reference clock frequencies table is used). Use clocks and + clock-names in order to assign it +- refclk-frequency: Frequency of the REFCLK signal as defined by REF_SEL + pins (optional, if not provided, driver will not set rate of the + REFCLK signal and assume that a value from the primary reference + clock frequencies table is used) + +Examples: + usb3503@8 { + compatible = "smsc,usb3503"; + reg = <0x08>; + connect-gpios = <&gpx3 0 1>; + disabled-ports = <2 3>; + intn-gpios = <&gpx3 4 1>; + reset-gpios = <&gpx3 5 1>; + initial-mode = <1>; + clocks = <&clks 80>; + clock-names = "refclk"; + }; diff --git a/Documentation/devicetree/bindings/usb/usb4604.txt b/Documentation/devicetree/bindings/usb/usb4604.txt new file mode 100644 index 000000000..82506d177 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usb4604.txt @@ -0,0 +1,19 @@ +SMSC USB4604 High-Speed Hub Controller + +Required properties: +- compatible: Should be "smsc,usb4604" + +Optional properties: +- reg: Specifies the i2c slave address, it is required and should be 0x2d + if I2C is used. +- reset-gpios: Should specify GPIO for reset. +- initial-mode: Should specify initial mode. + (1 for HUB mode, 2 for STANDBY mode) + +Examples: + usb-hub@2d { + compatible = "smsc,usb4604"; + reg = <0x2d>; + reset-gpios = <&gpx3 5 1>; + initial-mode = <1>; + }; diff --git a/Documentation/devicetree/bindings/usb/usbmisc-imx.txt b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt new file mode 100644 index 000000000..a85a631ec --- /dev/null +++ b/Documentation/devicetree/bindings/usb/usbmisc-imx.txt @@ -0,0 +1,17 @@ +* Freescale i.MX non-core registers + +Required properties: +- #index-cells: Cells used to descibe usb controller index. Should be <1> +- compatible: Should be one of below: + "fsl,imx6q-usbmisc" for imx6q + "fsl,vf610-usbmisc" for Vybrid vf610 + "fsl,imx6sx-usbmisc" for imx6sx + "fsl,imx7d-usbmisc" for imx7d +- reg: Should contain registers location and length + +Examples: +usbmisc@2184800 { + #index-cells = <1>; + compatible = "fsl,imx6q-usbmisc"; + reg = <0x02184800 0x200>; +}; diff --git a/Documentation/devicetree/bindings/usb/ux500-usb.txt b/Documentation/devicetree/bindings/usb/ux500-usb.txt new file mode 100644 index 000000000..439a41c79 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/ux500-usb.txt @@ -0,0 +1,50 @@ +Ux500 MUSB + +Required properties: + - compatible : Should be "stericsson,db8500-musb" + - reg : Offset and length of registers + - interrupts : Interrupt; mode, number and trigger + - dr_mode : Dual-role; either host mode "host", peripheral mode "peripheral" + or both "otg" + +Optional properties: + - dmas : A list of dma channels; + dma-controller, event-line, fixed-channel, flags + - dma-names : An ordered list of channel names affiliated to the above + +Example: + +usb_per5@a03e0000 { + compatible = "stericsson,db8500-musb"; + reg = <0xa03e0000 0x10000>; + interrupts = <0 23 0x4>; + interrupt-names = "mc"; + + dr_mode = "otg"; + + dmas = <&dma 38 0 0x2>, /* Logical - DevToMem */ + <&dma 38 0 0x0>, /* Logical - MemToDev */ + <&dma 37 0 0x2>, /* Logical - DevToMem */ + <&dma 37 0 0x0>, /* Logical - MemToDev */ + <&dma 36 0 0x2>, /* Logical - DevToMem */ + <&dma 36 0 0x0>, /* Logical - MemToDev */ + <&dma 19 0 0x2>, /* Logical - DevToMem */ + <&dma 19 0 0x0>, /* Logical - MemToDev */ + <&dma 18 0 0x2>, /* Logical - DevToMem */ + <&dma 18 0 0x0>, /* Logical - MemToDev */ + <&dma 17 0 0x2>, /* Logical - DevToMem */ + <&dma 17 0 0x0>, /* Logical - MemToDev */ + <&dma 16 0 0x2>, /* Logical - DevToMem */ + <&dma 16 0 0x0>, /* Logical - MemToDev */ + <&dma 39 0 0x2>, /* Logical - DevToMem */ + <&dma 39 0 0x0>; /* Logical - MemToDev */ + + dma-names = "iep_1_9", "oep_1_9", + "iep_2_10", "oep_2_10", + "iep_3_11", "oep_3_11", + "iep_4_12", "oep_4_12", + "iep_5_13", "oep_5_13", + "iep_6_14", "oep_6_14", + "iep_7_15", "oep_7_15", + "iep_8", "oep_8"; +}; |