diff options
Diffstat (limited to '')
| -rw-r--r-- | arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 286 |
1 files changed, 286 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts new file mode 100644 index 000000000..14062b453 --- /dev/null +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts @@ -0,0 +1,286 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * dts file for Xilinx ZynqMP ZCU100 revC + * + * (C) Copyright 2016 - 2018, Xilinx, Inc. + * + * Michal Simek <michal.simek@xilinx.com> + * Nathalie Chan King Choy + */ + +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "ZynqMP ZCU100 RevC"; + compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp"; + + aliases { + i2c0 = &i2c1; + rtc0 = &rtc; + serial0 = &uart1; + serial1 = &uart0; + serial2 = &dcc; + spi0 = &spi0; + spi1 = &spi1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + sw4 { + label = "sw4"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + gpio-key,wakeup; + autorepeat; + }; + }; + + leds { + compatible = "gpio-leds"; + ds2 { + label = "ds2"; + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + ds3 { + label = "ds3"; + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; /* WLAN tx */ + default-state = "off"; + }; + + ds4 { + label = "ds4"; + gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0rx"; /* WLAN rx */ + default-state = "off"; + }; + + ds5 { + label = "ds5"; + gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + }; + + vbus-det { /* U5 USB5744 VBUS detection via MIO25 */ + label = "vbus_det"; + gpios = <&gpio 25 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + wmmcsdio_fixed: fixedregulator-mmcsdio { + compatible = "regulator-fixed"; + regulator-name = "wmmcsdio_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + post-power-on-delay-ms = <10>; + }; +}; + +&dcc { + status = "okay"; +}; + +&gpio { + status = "okay"; + gpio-line-names = "UART1_TX", "UART1_RX", "UART0_RX", "UART0_TX", "I2C1_SCL", + "I2C1_SDA", "SPI1_SCLK", "WLAN_EN", "BT_EN", "SPI1_CS", + "SPI1_MISO", "SPI1_MOSI", "I2C_MUX_RESET", "SD0_DAT0", "SD0_DAT1", + "SD0_DAT2", "SD0_DAT3", "PS_LED3", "PS_LED2", "PS_LED1", + "PS_LED0", "SD0_CMD", "SD0_CLK", "GPIO_PB", "SD0_DETECT", + "VBUS_DET", "POWER_INT", "DP_AUX", "DP_HPD", "DP_OE", + "DP_AUX_IN", "INA226_ALERT", "PS_FP_PWR_EN", "PL_PWR_EN", "POWER_KILL", + "", "GPIO-A", "GPIO-B", "SPI0_SCLK", "GPIO-C", + "GPIO-D", "SPI0_CS", "SPI0_MISO", "SPI_MOSI", "GPIO-E", + "GPIO-F", "SD1_D0", "SD1_D1", "SD1_D2", "SD1_D3", + "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", + "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", + "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", + "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", + "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", + "USB_DATA7", "WLAN_IRQ", "PMIC_IRQ", /* MIO end and EMIO start */ + "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", ""; +}; + +&i2c1 { + status = "okay"; + clock-frequency = <100000>; + i2c-mux@75 { /* u11 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x75>; + i2csw_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + label = "LS-I2C0"; + }; + i2csw_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + label = "LS-I2C1"; + }; + i2csw_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + label = "HS-I2C2"; + }; + i2csw_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + label = "HS-I2C3"; + }; + i2csw_4: i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4>; + + pmic: pmic@5e { /* Custom TI PMIC u33 */ + compatible = "ti,tps65086"; + reg = <0x5e>; + interrupt-parent = <&gpio>; + interrupts = <77 GPIO_ACTIVE_LOW>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + i2csw_5: i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + /* PS_PMBUS */ + ina226@40 { /* u35 */ + compatible = "ti,ina226"; + reg = <0x40>; + shunt-resistor = <10000>; + /* MIO31 is alert which should be routed to PMUFW */ + }; + }; + i2csw_6: i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + /* + * Not Connected + */ + }; + i2csw_7: i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + /* + * usb5744 (DNP) - U5 + * 100kHz - this is default freq for us + */ + }; + }; +}; + +&rtc { + status = "okay"; +}; + +/* SD0 only supports 3.3V, no level shifter */ +&sdhci0 { + status = "okay"; + no-1-8-v; + broken-cd; /* CD has to be enabled by default */ + disable-wp; +}; + +&sdhci1 { + status = "okay"; + bus-width = <0x4>; + non-removable; + disable-wp; + cap-power-off-card; + mmc-pwrseq = <&sdio_pwrseq>; + vqmmc-supply = <&wmmcsdio_fixed>; + #address-cells = <1>; + #size-cells = <0>; + wlcore: wifi@2 { + compatible = "ti,wl1831"; + reg = <2>; + interrupt-parent = <&gpio>; + interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */ + }; +}; + +&spi0 { /* Low Speed connector */ + status = "okay"; + label = "LS-SPI0"; +}; + +&spi1 { /* High Speed connector */ + status = "okay"; + label = "HS-SPI1"; +}; + +&uart0 { + status = "okay"; + bluetooth { + compatible = "ti,wl1831-st"; + enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart1 { + status = "okay"; + +}; + +/* ULPI SMSC USB3320 */ +&usb0 { + status = "okay"; +}; + +/* ULPI SMSC USB3320 */ +&usb1 { + status = "okay"; +}; + +&watchdog0 { + status = "okay"; +}; |