diff options
Diffstat (limited to '')
| -rw-r--r-- | arch/x86/boot/header.S | 636 |
1 files changed, 636 insertions, 0 deletions
diff --git a/arch/x86/boot/header.S b/arch/x86/boot/header.S new file mode 100644 index 000000000..850b8762e --- /dev/null +++ b/arch/x86/boot/header.S @@ -0,0 +1,636 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * header.S + * + * Copyright (C) 1991, 1992 Linus Torvalds + * + * Based on bootsect.S and setup.S + * modified by more people than can be counted + * + * Rewritten as a common file by H. Peter Anvin (Apr 2007) + * + * BIG FAT NOTE: We're in real mode using 64k segments. Therefore segment + * addresses must be multiplied by 16 to obtain their respective linear + * addresses. To avoid confusion, linear addresses are written using leading + * hex while segment addresses are written as segment:offset. + * + */ + +#include <asm/segment.h> +#include <asm/boot.h> +#include <asm/page_types.h> +#include <asm/setup.h> +#include <asm/bootparam.h> +#include "boot.h" +#include "voffset.h" +#include "zoffset.h" + +BOOTSEG = 0x07C0 /* original address of boot-sector */ +SYSSEG = 0x1000 /* historical load address >> 4 */ + +#ifndef SVGA_MODE +#define SVGA_MODE ASK_VGA +#endif + +#ifndef ROOT_RDONLY +#define ROOT_RDONLY 1 +#endif + + .code16 + .section ".bstext", "ax" + + .global bootsect_start +bootsect_start: +#ifdef CONFIG_EFI_STUB + # "MZ", MS-DOS header + .byte 0x4d + .byte 0x5a +#endif + + # Normalize the start address + ljmp $BOOTSEG, $start2 + +start2: + movw %cs, %ax + movw %ax, %ds + movw %ax, %es + movw %ax, %ss + xorw %sp, %sp + sti + cld + + movw $bugger_off_msg, %si + +msg_loop: + lodsb + andb %al, %al + jz bs_die + movb $0xe, %ah + movw $7, %bx + int $0x10 + jmp msg_loop + +bs_die: + # Allow the user to press a key, then reboot + xorw %ax, %ax + int $0x16 + int $0x19 + + # int 0x19 should never return. In case it does anyway, + # invoke the BIOS reset code... + ljmp $0xf000,$0xfff0 + +#ifdef CONFIG_EFI_STUB + .org 0x3c + # + # Offset to the PE header. + # + .long pe_header +#endif /* CONFIG_EFI_STUB */ + + .section ".bsdata", "a" +bugger_off_msg: + .ascii "Use a boot loader.\r\n" + .ascii "\n" + .ascii "Remove disk and press any key to reboot...\r\n" + .byte 0 + +#ifdef CONFIG_EFI_STUB +pe_header: + .ascii "PE" + .word 0 + +coff_header: +#ifdef CONFIG_X86_32 + .word 0x14c # i386 +#else + .word 0x8664 # x86-64 +#endif + .word 4 # nr_sections + .long 0 # TimeDateStamp + .long 0 # PointerToSymbolTable + .long 1 # NumberOfSymbols + .word section_table - optional_header # SizeOfOptionalHeader +#ifdef CONFIG_X86_32 + .word 0x306 # Characteristics. + # IMAGE_FILE_32BIT_MACHINE | + # IMAGE_FILE_DEBUG_STRIPPED | + # IMAGE_FILE_EXECUTABLE_IMAGE | + # IMAGE_FILE_LINE_NUMS_STRIPPED +#else + .word 0x206 # Characteristics + # IMAGE_FILE_DEBUG_STRIPPED | + # IMAGE_FILE_EXECUTABLE_IMAGE | + # IMAGE_FILE_LINE_NUMS_STRIPPED +#endif + +optional_header: +#ifdef CONFIG_X86_32 + .word 0x10b # PE32 format +#else + .word 0x20b # PE32+ format +#endif + .byte 0x02 # MajorLinkerVersion + .byte 0x14 # MinorLinkerVersion + + # Filled in by build.c + .long 0 # SizeOfCode + + .long 0 # SizeOfInitializedData + .long 0 # SizeOfUninitializedData + + # Filled in by build.c + .long 0x0000 # AddressOfEntryPoint + + .long 0x0200 # BaseOfCode +#ifdef CONFIG_X86_32 + .long 0 # data +#endif + +extra_header_fields: +#ifdef CONFIG_X86_32 + .long 0 # ImageBase +#else + .quad 0 # ImageBase +#endif + .long 0x20 # SectionAlignment + .long 0x20 # FileAlignment + .word 0 # MajorOperatingSystemVersion + .word 0 # MinorOperatingSystemVersion + .word 0 # MajorImageVersion + .word 0 # MinorImageVersion + .word 0 # MajorSubsystemVersion + .word 0 # MinorSubsystemVersion + .long 0 # Win32VersionValue + + # + # The size of the bzImage is written in tools/build.c + # + .long 0 # SizeOfImage + + .long 0x200 # SizeOfHeaders + .long 0 # CheckSum + .word 0xa # Subsystem (EFI application) + .word 0 # DllCharacteristics +#ifdef CONFIG_X86_32 + .long 0 # SizeOfStackReserve + .long 0 # SizeOfStackCommit + .long 0 # SizeOfHeapReserve + .long 0 # SizeOfHeapCommit +#else + .quad 0 # SizeOfStackReserve + .quad 0 # SizeOfStackCommit + .quad 0 # SizeOfHeapReserve + .quad 0 # SizeOfHeapCommit +#endif + .long 0 # LoaderFlags + .long 0x6 # NumberOfRvaAndSizes + + .quad 0 # ExportTable + .quad 0 # ImportTable + .quad 0 # ResourceTable + .quad 0 # ExceptionTable + .quad 0 # CertificationTable + .quad 0 # BaseRelocationTable + + # Section table +section_table: + # + # The offset & size fields are filled in by build.c. + # + .ascii ".setup" + .byte 0 + .byte 0 + .long 0 + .long 0x0 # startup_{32,64} + .long 0 # Size of initialized data + # on disk + .long 0x0 # startup_{32,64} + .long 0 # PointerToRelocations + .long 0 # PointerToLineNumbers + .word 0 # NumberOfRelocations + .word 0 # NumberOfLineNumbers + .long 0x60500020 # Characteristics (section flags) + + # + # The EFI application loader requires a relocation section + # because EFI applications must be relocatable. The .reloc + # offset & size fields are filled in by build.c. + # + .ascii ".reloc" + .byte 0 + .byte 0 + .long 0 + .long 0 + .long 0 # SizeOfRawData + .long 0 # PointerToRawData + .long 0 # PointerToRelocations + .long 0 # PointerToLineNumbers + .word 0 # NumberOfRelocations + .word 0 # NumberOfLineNumbers + .long 0x42100040 # Characteristics (section flags) + + # + # The offset & size fields are filled in by build.c. + # + .ascii ".text" + .byte 0 + .byte 0 + .byte 0 + .long 0 + .long 0x0 # startup_{32,64} + .long 0 # Size of initialized data + # on disk + .long 0x0 # startup_{32,64} + .long 0 # PointerToRelocations + .long 0 # PointerToLineNumbers + .word 0 # NumberOfRelocations + .word 0 # NumberOfLineNumbers + .long 0x60500020 # Characteristics (section flags) + + # + # The offset & size fields are filled in by build.c. + # + .ascii ".bss" + .byte 0 + .byte 0 + .byte 0 + .byte 0 + .long 0 + .long 0x0 + .long 0 # Size of initialized data + # on disk + .long 0x0 + .long 0 # PointerToRelocations + .long 0 # PointerToLineNumbers + .word 0 # NumberOfRelocations + .word 0 # NumberOfLineNumbers + .long 0xc8000080 # Characteristics (section flags) + +#endif /* CONFIG_EFI_STUB */ + + # Kernel attributes; used by setup. This is part 1 of the + # header, from the old boot sector. + + .section ".header", "a" + .globl sentinel +sentinel: .byte 0xff, 0xff /* Used to detect broken loaders */ + + .globl hdr +hdr: +setup_sects: .byte 0 /* Filled in by build.c */ +root_flags: .word ROOT_RDONLY +syssize: .long 0 /* Filled in by build.c */ +ram_size: .word 0 /* Obsolete */ +vid_mode: .word SVGA_MODE +root_dev: .word 0 /* Filled in by build.c */ +boot_flag: .word 0xAA55 + + # offset 512, entry point + + .globl _start +_start: + # Explicitly enter this as bytes, or the assembler + # tries to generate a 3-byte jump here, which causes + # everything else to push off to the wrong offset. + .byte 0xeb # short (2-byte) jump + .byte start_of_setup-1f +1: + + # Part 2 of the header, from the old setup.S + + .ascii "HdrS" # header signature + .word 0x020d # header version number (>= 0x0105) + # or else old loadlin-1.5 will fail) + .globl realmode_swtch +realmode_swtch: .word 0, 0 # default_switch, SETUPSEG +start_sys_seg: .word SYSSEG # obsolete and meaningless, but just + # in case something decided to "use" it + .word kernel_version-512 # pointing to kernel version string + # above section of header is compatible + # with loadlin-1.5 (header v1.5). Don't + # change it. + +type_of_loader: .byte 0 # 0 means ancient bootloader, newer + # bootloaders know to change this. + # See Documentation/x86/boot.txt for + # assigned ids + +# flags, unused bits must be zero (RFU) bit within loadflags +loadflags: + .byte LOADED_HIGH # The kernel is to be loaded high + +setup_move_size: .word 0x8000 # size to move, when setup is not + # loaded at 0x90000. We will move setup + # to 0x90000 then just before jumping + # into the kernel. However, only the + # loader knows how much data behind + # us also needs to be loaded. + +code32_start: # here loaders can put a different + # start address for 32-bit code. + .long 0x100000 # 0x100000 = default for big kernel + +ramdisk_image: .long 0 # address of loaded ramdisk image + # Here the loader puts the 32-bit + # address where it loaded the image. + # This only will be read by the kernel. + +ramdisk_size: .long 0 # its size in bytes + +bootsect_kludge: + .long 0 # obsolete + +heap_end_ptr: .word _end+STACK_SIZE-512 + # (Header version 0x0201 or later) + # space from here (exclusive) down to + # end of setup code can be used by setup + # for local heap purposes. + +ext_loader_ver: + .byte 0 # Extended boot loader version +ext_loader_type: + .byte 0 # Extended boot loader type + +cmd_line_ptr: .long 0 # (Header version 0x0202 or later) + # If nonzero, a 32-bit pointer + # to the kernel command line. + # The command line should be + # located between the start of + # setup and the end of low + # memory (0xa0000), or it may + # get overwritten before it + # gets read. If this field is + # used, there is no longer + # anything magical about the + # 0x90000 segment; the setup + # can be located anywhere in + # low memory 0x10000 or higher. + +initrd_addr_max: .long 0x7fffffff + # (Header version 0x0203 or later) + # The highest safe address for + # the contents of an initrd + # The current kernel allows up to 4 GB, + # but leave it at 2 GB to avoid + # possible bootloader bugs. + +kernel_alignment: .long CONFIG_PHYSICAL_ALIGN #physical addr alignment + #required for protected mode + #kernel +#ifdef CONFIG_RELOCATABLE +relocatable_kernel: .byte 1 +#else +relocatable_kernel: .byte 0 +#endif +min_alignment: .byte MIN_KERNEL_ALIGN_LG2 # minimum alignment + +xloadflags: +#ifdef CONFIG_X86_64 +# define XLF0 XLF_KERNEL_64 /* 64-bit kernel */ +#else +# define XLF0 0 +#endif + +#if defined(CONFIG_RELOCATABLE) && defined(CONFIG_X86_64) + /* kernel/boot_param/ramdisk could be loaded above 4g */ +# define XLF1 XLF_CAN_BE_LOADED_ABOVE_4G +#else +# define XLF1 0 +#endif + +#ifdef CONFIG_EFI_STUB +# ifdef CONFIG_EFI_MIXED +# define XLF23 (XLF_EFI_HANDOVER_32|XLF_EFI_HANDOVER_64) +# else +# ifdef CONFIG_X86_64 +# define XLF23 XLF_EFI_HANDOVER_64 /* 64-bit EFI handover ok */ +# else +# define XLF23 XLF_EFI_HANDOVER_32 /* 32-bit EFI handover ok */ +# endif +# endif +#else +# define XLF23 0 +#endif + +#if defined(CONFIG_X86_64) && defined(CONFIG_EFI) && defined(CONFIG_KEXEC_CORE) +# define XLF4 XLF_EFI_KEXEC +#else +# define XLF4 0 +#endif + + .word XLF0 | XLF1 | XLF23 | XLF4 + +cmdline_size: .long COMMAND_LINE_SIZE-1 #length of the command line, + #added with boot protocol + #version 2.06 + +hardware_subarch: .long 0 # subarchitecture, added with 2.07 + # default to 0 for normal x86 PC + +hardware_subarch_data: .quad 0 + +payload_offset: .long ZO_input_data +payload_length: .long ZO_z_input_len + +setup_data: .quad 0 # 64-bit physical pointer to + # single linked list of + # struct setup_data + +pref_address: .quad LOAD_PHYSICAL_ADDR # preferred load addr + +# +# Getting to provably safe in-place decompression is hard. Worst case +# behaviours need to be analyzed. Here let's take the decompression of +# a gzip-compressed kernel as example, to illustrate it: +# +# The file layout of gzip compressed kernel is: +# +# magic[2] +# method[1] +# flags[1] +# timestamp[4] +# extraflags[1] +# os[1] +# compressed data blocks[N] +# crc[4] orig_len[4] +# +# ... resulting in +18 bytes overhead of uncompressed data. +# +# (For more information, please refer to RFC 1951 and RFC 1952.) +# +# Files divided into blocks +# 1 bit (last block flag) +# 2 bits (block type) +# +# 1 block occurs every 32K -1 bytes or when there 50% compression +# has been achieved. The smallest block type encoding is always used. +# +# stored: +# 32 bits length in bytes. +# +# fixed: +# magic fixed tree. +# symbols. +# +# dynamic: +# dynamic tree encoding. +# symbols. +# +# +# The buffer for decompression in place is the length of the uncompressed +# data, plus a small amount extra to keep the algorithm safe. The +# compressed data is placed at the end of the buffer. The output pointer +# is placed at the start of the buffer and the input pointer is placed +# where the compressed data starts. Problems will occur when the output +# pointer overruns the input pointer. +# +# The output pointer can only overrun the input pointer if the input +# pointer is moving faster than the output pointer. A condition only +# triggered by data whose compressed form is larger than the uncompressed +# form. +# +# The worst case at the block level is a growth of the compressed data +# of 5 bytes per 32767 bytes. +# +# The worst case internal to a compressed block is very hard to figure. +# The worst case can at least be bounded by having one bit that represents +# 32764 bytes and then all of the rest of the bytes representing the very +# very last byte. +# +# All of which is enough to compute an amount of extra data that is required +# to be safe. To avoid problems at the block level allocating 5 extra bytes +# per 32767 bytes of data is sufficient. To avoid problems internal to a +# block adding an extra 32767 bytes (the worst case uncompressed block size) +# is sufficient, to ensure that in the worst case the decompressed data for +# block will stop the byte before the compressed data for a block begins. +# To avoid problems with the compressed data's meta information an extra 18 +# bytes are needed. Leading to the formula: +# +# extra_bytes = (uncompressed_size >> 12) + 32768 + 18 +# +# Adding 8 bytes per 32K is a bit excessive but much easier to calculate. +# Adding 32768 instead of 32767 just makes for round numbers. +# +# Above analysis is for decompressing gzip compressed kernel only. Up to +# now 6 different decompressor are supported all together. And among them +# xz stores data in chunks and has maximum chunk of 64K. Hence safety +# margin should be updated to cover all decompressors so that we don't +# need to deal with each of them separately. Please check +# the description in lib/decompressor_xxx.c for specific information. +# +# extra_bytes = (uncompressed_size >> 12) + 65536 + 128 +# +# LZ4 is even worse: data that cannot be further compressed grows by 0.4%, +# or one byte per 256 bytes. OTOH, we can safely get rid of the +128 as +# the size-dependent part now grows so fast. +# +# extra_bytes = (uncompressed_size >> 8) + 65536 + +#define ZO_z_extra_bytes ((ZO_z_output_len >> 8) + 65536) +#if ZO_z_output_len > ZO_z_input_len +# define ZO_z_extract_offset (ZO_z_output_len + ZO_z_extra_bytes - \ + ZO_z_input_len) +#else +# define ZO_z_extract_offset ZO_z_extra_bytes +#endif + +/* + * The extract_offset has to be bigger than ZO head section. Otherwise when + * the head code is running to move ZO to the end of the buffer, it will + * overwrite the head code itself. + */ +#if (ZO__ehead - ZO_startup_32) > ZO_z_extract_offset +# define ZO_z_min_extract_offset ((ZO__ehead - ZO_startup_32 + 4095) & ~4095) +#else +# define ZO_z_min_extract_offset ((ZO_z_extract_offset + 4095) & ~4095) +#endif + +#define ZO_INIT_SIZE (ZO__end - ZO_startup_32 + ZO_z_min_extract_offset) + +#define VO_INIT_SIZE (VO__end - VO__text) +#if ZO_INIT_SIZE > VO_INIT_SIZE +# define INIT_SIZE ZO_INIT_SIZE +#else +# define INIT_SIZE VO_INIT_SIZE +#endif + +init_size: .long INIT_SIZE # kernel initialization size +handover_offset: .long 0 # Filled in by build.c + +# End of setup header ##################################################### + + .section ".entrytext", "ax" +start_of_setup: +# Force %es = %ds + movw %ds, %ax + movw %ax, %es + cld + +# Apparently some ancient versions of LILO invoked the kernel with %ss != %ds, +# which happened to work by accident for the old code. Recalculate the stack +# pointer if %ss is invalid. Otherwise leave it alone, LOADLIN sets up the +# stack behind its own code, so we can't blindly put it directly past the heap. + + movw %ss, %dx + cmpw %ax, %dx # %ds == %ss? + movw %sp, %dx + je 2f # -> assume %sp is reasonably set + + # Invalid %ss, make up a new stack + movw $_end, %dx + testb $CAN_USE_HEAP, loadflags + jz 1f + movw heap_end_ptr, %dx +1: addw $STACK_SIZE, %dx + jnc 2f + xorw %dx, %dx # Prevent wraparound + +2: # Now %dx should point to the end of our stack space + andw $~3, %dx # dword align (might as well...) + jnz 3f + movw $0xfffc, %dx # Make sure we're not zero +3: movw %ax, %ss + movzwl %dx, %esp # Clear upper half of %esp + sti # Now we should have a working stack + +# We will have entered with %cs = %ds+0x20, normalize %cs so +# it is on par with the other segments. + pushw %ds + pushw $6f + lretw +6: + +# Check signature at end of setup + cmpl $0x5a5aaa55, setup_sig + jne setup_bad + +# Zero the bss + movw $__bss_start, %di + movw $_end+3, %cx + xorl %eax, %eax + subw %di, %cx + shrw $2, %cx + rep; stosl + +# Jump to C code (should not return) + calll main + +# Setup corrupt somehow... +setup_bad: + movl $setup_corrupt, %eax + calll puts + # Fall through... + + .globl die + .type die, @function +die: + hlt + jmp die + + .size die, .-die + + .section ".initdata", "a" +setup_corrupt: + .byte 7 + .string "No setup signature found...\n" |