diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/isdn/hisax/hfc_usb.h | 208 |
1 files changed, 208 insertions, 0 deletions
diff --git a/drivers/isdn/hisax/hfc_usb.h b/drivers/isdn/hisax/hfc_usb.h new file mode 100644 index 000000000..9a212330e --- /dev/null +++ b/drivers/isdn/hisax/hfc_usb.h @@ -0,0 +1,208 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * hfc_usb.h + * + * $Id: hfc_usb.h,v 1.1.2.5 2007/08/20 14:36:03 mbachem Exp $ + */ + +#ifndef __HFC_USB_H__ +#define __HFC_USB_H__ + +#define DRIVER_AUTHOR "Peter Sprenger (sprenger@moving-byters.de)" +#define DRIVER_DESC "HFC-S USB based HiSAX ISDN driver" + + +#define HFC_CTRL_TIMEOUT 20 /* 5ms timeout writing/reading regs */ +#define HFC_TIMER_T3 8000 /* timeout for l1 activation timer */ +#define HFC_TIMER_T4 500 /* time for state change interval */ + +#define HFCUSB_L1_STATECHANGE 0 /* L1 state changed */ +#define HFCUSB_L1_DRX 1 /* D-frame received */ +#define HFCUSB_L1_ERX 2 /* E-frame received */ +#define HFCUSB_L1_DTX 4 /* D-frames completed */ + +#define MAX_BCH_SIZE 2048 /* allowed B-channel packet size */ + +#define HFCUSB_RX_THRESHOLD 64 /* threshold for fifo report bit rx */ +#define HFCUSB_TX_THRESHOLD 64 /* threshold for fifo report bit tx */ + +#define HFCUSB_CHIP_ID 0x16 /* Chip ID register index */ +#define HFCUSB_CIRM 0x00 /* cirm register index */ +#define HFCUSB_USB_SIZE 0x07 /* int length register */ +#define HFCUSB_USB_SIZE_I 0x06 /* iso length register */ +#define HFCUSB_F_CROSS 0x0b /* bit order register */ +#define HFCUSB_CLKDEL 0x37 /* bit delay register */ +#define HFCUSB_CON_HDLC 0xfa /* channel connect register */ +#define HFCUSB_HDLC_PAR 0xfb +#define HFCUSB_SCTRL 0x31 /* S-bus control register (tx) */ +#define HFCUSB_SCTRL_E 0x32 /* same for E and special funcs */ +#define HFCUSB_SCTRL_R 0x33 /* S-bus control register (rx) */ +#define HFCUSB_F_THRES 0x0c /* threshold register */ +#define HFCUSB_FIFO 0x0f /* fifo select register */ +#define HFCUSB_F_USAGE 0x1a /* fifo usage register */ +#define HFCUSB_MST_MODE0 0x14 +#define HFCUSB_MST_MODE1 0x15 +#define HFCUSB_P_DATA 0x1f +#define HFCUSB_INC_RES_F 0x0e +#define HFCUSB_STATES 0x30 + +#define HFCUSB_CHIPID 0x40 /* ID value of HFC-S USB */ + + +/* fifo registers */ +#define HFCUSB_NUM_FIFOS 8 /* maximum number of fifos */ +#define HFCUSB_B1_TX 0 /* index for B1 transmit bulk/int */ +#define HFCUSB_B1_RX 1 /* index for B1 receive bulk/int */ +#define HFCUSB_B2_TX 2 +#define HFCUSB_B2_RX 3 +#define HFCUSB_D_TX 4 +#define HFCUSB_D_RX 5 +#define HFCUSB_PCM_TX 6 +#define HFCUSB_PCM_RX 7 + +/* + * used to switch snd_transfer_mode for different TA modes e.g. the Billion USB TA just + * supports ISO out, while the Cologne Chip EVAL TA just supports BULK out + */ +#define USB_INT 0 +#define USB_BULK 1 +#define USB_ISOC 2 + +#define ISOC_PACKETS_D 8 +#define ISOC_PACKETS_B 8 +#define ISO_BUFFER_SIZE 128 + +/* Fifo flow Control for TX ISO */ +#define SINK_MAX 68 +#define SINK_MIN 48 +#define SINK_DMIN 12 +#define SINK_DMAX 18 +#define BITLINE_INF (-64 * 8) + +/* HFC-S USB register access by Control-URSs */ +#define write_usb(a, b, c) usb_control_msg((a)->dev, (a)->ctrl_out_pipe, 0, 0x40, (c), (b), NULL, 0, HFC_CTRL_TIMEOUT) +#define read_usb(a, b, c) usb_control_msg((a)->dev, (a)->ctrl_in_pipe, 1, 0xC0, 0, (b), (c), 1, HFC_CTRL_TIMEOUT) +#define HFC_CTRL_BUFSIZE 32 + +/* entry and size of output/input control buffer */ +typedef struct { + __u8 hfc_reg; /* register number */ + __u8 reg_val; /* value to be written (or read) */ + int action; /* data for action handler */ +} ctrl_buft; + +/* Debugging Flags */ +#define HFCUSB_DBG_INIT 0x0001 +#define HFCUSB_DBG_STATES 0x0002 +#define HFCUSB_DBG_DCHANNEL 0x0080 +#define HFCUSB_DBG_FIFO_ERR 0x4000 +#define HFCUSB_DBG_VERBOSE_USB 0x8000 + +/* + * URB error codes: + * Used to represent a list of values and their respective symbolic names + */ +struct hfcusb_symbolic_list { + const int num; + const char *name; +}; + +static struct hfcusb_symbolic_list urb_errlist[] = { + {-ENOMEM, "No memory for allocation of internal structures"}, + {-ENOSPC, "The host controller's bandwidth is already consumed"}, + {-ENOENT, "URB was canceled by unlink_urb"}, + {-EXDEV, "ISO transfer only partially completed"}, + {-EAGAIN, "Too match scheduled for the future"}, + {-ENXIO, "URB already queued"}, + {-EFBIG, "Too much ISO frames requested"}, + {-ENOSR, "Buffer error (overrun)"}, + {-EPIPE, "Specified endpoint is stalled (device not responding)"}, + {-EOVERFLOW, "Babble (bad cable?)"}, + {-EPROTO, "Bit-stuff error (bad cable?)"}, + {-EILSEQ, "CRC/Timeout"}, + {-ETIMEDOUT, "NAK (device does not respond)"}, + {-ESHUTDOWN, "Device unplugged"}, + {-1, NULL} +}; + + +/* + * device dependent information to support different + * ISDN Ta's using the HFC-S USB chip + */ + +/* USB descriptor need to contain one of the following EndPoint combination: */ +#define CNF_4INT3ISO 1 // 4 INT IN, 3 ISO OUT +#define CNF_3INT3ISO 2 // 3 INT IN, 3 ISO OUT +#define CNF_4ISO3ISO 3 // 4 ISO IN, 3 ISO OUT +#define CNF_3ISO3ISO 4 // 3 ISO IN, 3 ISO OUT + +#define EP_NUL 1 // Endpoint at this position not allowed +#define EP_NOP 2 // all type of endpoints allowed at this position +#define EP_ISO 3 // Isochron endpoint mandatory at this position +#define EP_BLK 4 // Bulk endpoint mandatory at this position +#define EP_INT 5 // Interrupt endpoint mandatory at this position + +/* + * List of all supported endpoint configuration sets, used to find the + * best matching endpoint configuration within a devices' USB descriptor. + * We need at least 3 RX endpoints, and 3 TX endpoints, either + * INT-in and ISO-out, or ISO-in and ISO-out) + * with 4 RX endpoints even E-Channel logging is possible + */ +static int validconf[][19] = { + // INT in, ISO out config + {EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NOP, EP_INT, + EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_NUL, EP_NUL, + CNF_4INT3ISO, 2, 1}, + {EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_INT, EP_NUL, EP_NUL, + EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_ISO, EP_NUL, EP_NUL, EP_NUL, + CNF_3INT3ISO, 2, 0}, + // ISO in, ISO out config + {EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, + EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_NOP, EP_ISO, + CNF_4ISO3ISO, 2, 1}, + {EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, EP_NUL, + EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_ISO, EP_NUL, EP_NUL, + CNF_3ISO3ISO, 2, 0}, + {0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0} // EOL element +}; + +#ifdef CONFIG_HISAX_DEBUG +// string description of chosen config +static char *conf_str[] = { + "4 Interrupt IN + 3 Isochron OUT", + "3 Interrupt IN + 3 Isochron OUT", + "4 Isochron IN + 3 Isochron OUT", + "3 Isochron IN + 3 Isochron OUT" +}; +#endif + +typedef struct { + int vendor; // vendor id + int prod_id; // product id + char *vend_name; // vendor string + __u8 led_scheme; // led display scheme + signed short led_bits[8]; // array of 8 possible LED bitmask settings +} vendor_data; + +#define LED_OFF 0 // no LED support +#define LED_SCHEME1 1 // LED standard scheme +#define LED_SCHEME2 2 // not used yet... + +#define LED_POWER_ON 1 +#define LED_POWER_OFF 2 +#define LED_S0_ON 3 +#define LED_S0_OFF 4 +#define LED_B1_ON 5 +#define LED_B1_OFF 6 +#define LED_B1_DATA 7 +#define LED_B2_ON 8 +#define LED_B2_OFF 9 +#define LED_B2_DATA 10 + +#define LED_NORMAL 0 // LEDs are normal +#define LED_INVERTED 1 // LEDs are inverted + + +#endif // __HFC_USB_H__ |