diff options
Diffstat (limited to 'drivers/net/phy/Kconfig')
| -rw-r--r-- | drivers/net/phy/Kconfig | 444 |
1 files changed, 444 insertions, 0 deletions
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig new file mode 100644 index 000000000..2386871e1 --- /dev/null +++ b/drivers/net/phy/Kconfig @@ -0,0 +1,444 @@ +# +# PHY Layer Configuration +# + +menuconfig MDIO_DEVICE + tristate "MDIO bus device drivers" + help + MDIO devices and driver infrastructure code. + +config MDIO_BUS + tristate + default m if PHYLIB=m + default MDIO_DEVICE + help + This internal symbol is used for link time dependencies and it + reflects whether the mdio_bus/mdio_device code is built as a + loadable module or built-in. + +if MDIO_BUS + +config MDIO_BCM_IPROC + tristate "Broadcom iProc MDIO bus controller" + depends on ARCH_BCM_IPROC || COMPILE_TEST + depends on HAS_IOMEM && OF_MDIO + help + This module provides a driver for the MDIO busses found in the + Broadcom iProc SoC's. + +config MDIO_BCM_UNIMAC + tristate "Broadcom UniMAC MDIO bus controller" + depends on HAS_IOMEM + help + This module provides a driver for the Broadcom UniMAC MDIO busses. + This hardware can be found in the Broadcom GENET Ethernet MAC + controllers as well as some Broadcom Ethernet switches such as the + Starfighter 2 switches. + +config MDIO_BITBANG + tristate "Bitbanged MDIO buses" + help + This module implements the MDIO bus protocol in software, + for use by low level drivers that export the ability to + drive the relevant pins. + + If in doubt, say N. + +config MDIO_BUS_MUX + tristate + depends on OF_MDIO + help + This module provides a driver framework for MDIO bus + multiplexers which connect one of several child MDIO busses + to a parent bus. Switching between child busses is done by + device specific drivers. + +config MDIO_BUS_MUX_BCM_IPROC + tristate "Broadcom iProc based MDIO bus multiplexers" + depends on OF && OF_MDIO && (ARCH_BCM_IPROC || COMPILE_TEST) + select MDIO_BUS_MUX + default ARCH_BCM_IPROC + help + This module provides a driver for MDIO bus multiplexers found in + iProc based Broadcom SoCs. This multiplexer connects one of several + child MDIO bus to a parent bus. Buses could be internal as well as + external and selection logic lies inside the same multiplexer. + +config MDIO_BUS_MUX_GPIO + tristate "GPIO controlled MDIO bus multiplexers" + depends on OF_GPIO && OF_MDIO + select MDIO_BUS_MUX + help + This module provides a driver for MDIO bus multiplexers that + are controlled via GPIO lines. The multiplexer connects one of + several child MDIO busses to a parent bus. Child bus + selection is under the control of GPIO lines. + +config MDIO_BUS_MUX_MMIOREG + tristate "MMIO device-controlled MDIO bus multiplexers" + depends on OF_MDIO && HAS_IOMEM + select MDIO_BUS_MUX + help + This module provides a driver for MDIO bus multiplexers that + are controlled via a simple memory-mapped device, like an FPGA. + The multiplexer connects one of several child MDIO busses to a + parent bus. Child bus selection is under the control of one of + the FPGA's registers. + + Currently, only 8/16/32 bits registers are supported. + +config MDIO_CAVIUM + tristate + +config MDIO_GPIO + tristate "GPIO lib-based bitbanged MDIO buses" + depends on MDIO_BITBANG + depends on GPIOLIB || COMPILE_TEST + ---help--- + Supports GPIO lib-based MDIO busses. + + To compile this driver as a module, choose M here: the module + will be called mdio-gpio. + +config MDIO_HISI_FEMAC + tristate "Hisilicon FEMAC MDIO bus controller" + depends on HAS_IOMEM && OF_MDIO + help + This module provides a driver for the MDIO busses found in the + Hisilicon SoC that have an Fast Ethernet MAC. + +config MDIO_I2C + tristate + depends on I2C + help + Support I2C based PHYs. This provides a MDIO bus bridged + to I2C to allow PHYs connected in I2C mode to be accessed + using the existing infrastructure. + + This is library mode. + +config MDIO_MOXART + tristate "MOXA ART MDIO interface support" + depends on ARCH_MOXART || COMPILE_TEST + help + This driver supports the MDIO interface found in the network + interface units of the MOXA ART SoC + +config MDIO_MSCC_MIIM + tristate "Microsemi MIIM interface support" + depends on HAS_IOMEM + help + This driver supports the MIIM (MDIO) interface found in the network + switches of the Microsemi SoCs + +config MDIO_OCTEON + tristate "Octeon and some ThunderX SOCs MDIO buses" + depends on 64BIT + depends on HAS_IOMEM && OF_MDIO + select MDIO_CAVIUM + help + This module provides a driver for the Octeon and ThunderX MDIO + buses. It is required by the Octeon and ThunderX ethernet device + drivers on some systems. + +config MDIO_SUN4I + tristate "Allwinner sun4i MDIO interface support" + depends on ARCH_SUNXI || COMPILE_TEST + help + This driver supports the MDIO interface found in the network + interface units of the Allwinner SoC that have an EMAC (A10, + A12, A10s, etc.) + +config MDIO_THUNDER + tristate "ThunderX SOCs MDIO buses" + depends on 64BIT + depends on PCI + select MDIO_CAVIUM + select MDIO_DEVRES + help + This driver supports the MDIO interfaces found on Cavium + ThunderX SoCs when the MDIO bus device appears as a PCI + device. + +config MDIO_XGENE + tristate "APM X-Gene SoC MDIO bus controller" + depends on ARCH_XGENE || COMPILE_TEST + help + This module provides a driver for the MDIO busses found in the + APM X-Gene SoC's. + +endif + +config PHYLINK + tristate + depends on NETDEVICES + select PHYLIB + select SWPHY + help + PHYlink models the link between the PHY and MAC, allowing fixed + configuration links, PHYs, and Serdes links with MAC level + autonegotiation modes. + +menuconfig PHYLIB + tristate "PHY Device support and infrastructure" + depends on NETDEVICES + select MDIO_DEVICE + help + Ethernet controllers are usually attached to PHY + devices. This option provides infrastructure for + managing PHY devices. + +if PHYLIB + +config SWPHY + bool + +config LED_TRIGGER_PHY + bool "Support LED triggers for tracking link state" + depends on LEDS_TRIGGERS + ---help--- + Adds support for a set of LED trigger events per-PHY. Link + state change will trigger the events, for consumption by an + LED class driver. There are triggers for each link speed currently + supported by the PHY and also a one common "link" trigger as a + logical-or of all the link speed ones. + All these triggers are named according to the following pattern: + <mii bus id>:<phy>:<speed> + + Where speed is in the form: + <Speed in megabits>Mbps OR <Speed in gigabits>Gbps OR link + for any speed known to the PHY. + + +comment "MII PHY device drivers" + +config SFP + tristate "SFP cage support" + depends on I2C && PHYLINK + depends on HWMON || HWMON=n + select MDIO_I2C + +config AMD_PHY + tristate "AMD PHYs" + ---help--- + Currently supports the am79c874 + +config AQUANTIA_PHY + tristate "Aquantia PHYs" + ---help--- + Currently supports the Aquantia AQ1202, AQ2104, AQR105, AQR405 + +config AX88796B_PHY + tristate "Asix PHYs" + help + Currently supports the Asix Electronics PHY found in the X-Surf 100 + AX88796B package. + +config AT803X_PHY + tristate "AT803X PHYs" + ---help--- + Currently supports the AT8030 and AT8035 model + +config BCM63XX_PHY + tristate "Broadcom 63xx SOCs internal PHY" + depends on BCM63XX + select BCM_NET_PHYLIB + ---help--- + Currently supports the 6348 and 6358 PHYs. + +config BCM7XXX_PHY + tristate "Broadcom 7xxx SOCs internal PHYs" + select BCM_NET_PHYLIB + ---help--- + Currently supports the BCM7366, BCM7439, BCM7445, and + 40nm and 65nm generation of BCM7xxx Set Top Box SoCs. + +config BCM87XX_PHY + tristate "Broadcom BCM8706 and BCM8727 PHYs" + help + Currently supports the BCM8706 and BCM8727 10G Ethernet PHYs. + +config BCM_CYGNUS_PHY + tristate "Broadcom Cygnus SoC internal PHY" + depends on ARCH_BCM_CYGNUS || COMPILE_TEST + depends on MDIO_BCM_IPROC + select BCM_NET_PHYLIB + ---help--- + This PHY driver is for the 1G internal PHYs of the Broadcom + Cygnus Family SoC. + + Currently supports internal PHY's used in the BCM11300, + BCM11320, BCM11350, BCM11360, BCM58300, BCM58302, + BCM58303 & BCM58305 Broadcom Cygnus SoCs. + +config BCM_NET_PHYLIB + tristate + +config BROADCOM_PHY + tristate "Broadcom PHYs" + select BCM_NET_PHYLIB + ---help--- + Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464, + BCM5481, BCM54810 and BCM5482 PHYs. + +config CICADA_PHY + tristate "Cicada PHYs" + ---help--- + Currently supports the cis8204 + +config CORTINA_PHY + tristate "Cortina EDC CDR 10G Ethernet PHY" + ---help--- + Currently supports the CS4340 phy. + +config DAVICOM_PHY + tristate "Davicom PHYs" + ---help--- + Currently supports dm9161e and dm9131 + +config DP83822_PHY + tristate "Texas Instruments DP83822 PHY" + ---help--- + Supports the DP83822 PHY. + +config DP83TC811_PHY + tristate "Texas Instruments DP83TC822 PHY" + ---help--- + Supports the DP83TC822 PHY. + +config DP83848_PHY + tristate "Texas Instruments DP83848 PHY" + ---help--- + Supports the DP83848 PHY. + +config DP83867_PHY + tristate "Texas Instruments DP83867 Gigabit PHY" + ---help--- + Currently supports the DP83867 PHY. + +config FIXED_PHY + tristate "MDIO Bus/PHY emulation with fixed speed/link PHYs" + depends on PHYLIB + select SWPHY + ---help--- + Adds the platform "fixed" MDIO Bus to cover the boards that use + PHYs that are not connected to the real MDIO bus. + + Currently tested with mpc866ads and mpc8349e-mitx. + +config ICPLUS_PHY + tristate "ICPlus PHYs" + ---help--- + Currently supports the IP175C and IP1001 PHYs. + +config INTEL_XWAY_PHY + tristate "Intel XWAY PHYs" + ---help--- + Supports the Intel XWAY (former Lantiq) 11G and 22E PHYs. + These PHYs are marked as standalone chips under the names + PEF 7061, PEF 7071 and PEF 7072 or integrated into the Intel + SoCs xRX200, xRX300, xRX330, xRX350 and xRX550. + +config LSI_ET1011C_PHY + tristate "LSI ET1011C PHY" + ---help--- + Supports the LSI ET1011C PHY. + +config LXT_PHY + tristate "Intel LXT PHYs" + ---help--- + Currently supports the lxt970, lxt971 + +config MARVELL_PHY + tristate "Marvell PHYs" + ---help--- + Currently has a driver for the 88E1011S + +config MARVELL_10G_PHY + tristate "Marvell Alaska 10Gbit PHYs" + ---help--- + Support for the Marvell Alaska MV88X3310 and compatible PHYs. + +config MESON_GXL_PHY + tristate "Amlogic Meson GXL Internal PHY" + depends on ARCH_MESON || COMPILE_TEST + ---help--- + Currently has a driver for the Amlogic Meson GXL Internal PHY + +config MICREL_PHY + tristate "Micrel PHYs" + ---help--- + Supports the KSZ9021, VSC8201, KS8001 PHYs. + +config MICROCHIP_PHY + tristate "Microchip PHYs" + help + Supports the LAN88XX PHYs. + +config MICROCHIP_T1_PHY + tristate "Microchip T1 PHYs" + ---help--- + Supports the LAN87XX PHYs. + +config MICROSEMI_PHY + tristate "Microsemi PHYs" + ---help--- + Currently supports VSC8530, VSC8531, VSC8540 and VSC8541 PHYs + +config NATIONAL_PHY + tristate "National Semiconductor PHYs" + ---help--- + Currently supports the DP83865 PHY. + +config QSEMI_PHY + tristate "Quality Semiconductor PHYs" + ---help--- + Currently supports the qs6612 + +config REALTEK_PHY + tristate "Realtek PHYs" + ---help--- + Supports the Realtek 821x PHY. + +config RENESAS_PHY + tristate "Driver for Renesas PHYs" + ---help--- + Supports the Renesas PHYs uPD60620 and uPD60620A. + +config ROCKCHIP_PHY + tristate "Driver for Rockchip Ethernet PHYs" + ---help--- + Currently supports the integrated Ethernet PHY. + +config SMSC_PHY + tristate "SMSC PHYs" + ---help--- + Currently supports the LAN83C185, LAN8187 and LAN8700 PHYs + +config STE10XP + tristate "STMicroelectronics STe10Xp PHYs" + ---help--- + This is the driver for the STe100p and STe101p PHYs. + +config TERANETICS_PHY + tristate "Teranetics PHYs" + ---help--- + Currently supports the Teranetics TN2020 + +config VITESSE_PHY + tristate "Vitesse PHYs" + ---help--- + Currently supports the vsc8244 + +config XILINX_GMII2RGMII + tristate "Xilinx GMII2RGMII converter driver" + ---help--- + This driver support xilinx GMII to RGMII IP core it provides + the Reduced Gigabit Media Independent Interface(RGMII) between + Ethernet physical media devices and the Gigabit Ethernet controller. + +endif # PHYLIB + +config MICREL_KS8995MA + tristate "Micrel KS8995MA 5-ports 10/100 managed Ethernet switch" + depends on SPI |