diff options
Diffstat (limited to 'drivers/parisc/Kconfig')
| -rw-r--r-- | drivers/parisc/Kconfig | 180 |
1 files changed, 180 insertions, 0 deletions
diff --git a/drivers/parisc/Kconfig b/drivers/parisc/Kconfig new file mode 100644 index 000000000..5a48b5606 --- /dev/null +++ b/drivers/parisc/Kconfig @@ -0,0 +1,180 @@ +menu "Bus options (PCI, PCMCIA, EISA, GSC, ISA)" + +config GSC + bool "VSC/GSC/HSC bus support" + default y + help + The VSC, GSC and HSC busses were used from the earliest 700-series + workstations up to and including the C360/J2240 workstations. They + were also used in servers from the E-class to the K-class. They + are not found in B1000, C3000, J5000, A500, L1000, N4000 and upwards. + If in doubt, say "Y". + +config HPPB + bool "HP-PB bus support" + depends on GSC + help + The HP-PB bus was used in the Nova class and K-class servers. + If in doubt, say "Y" + +config IOMMU_CCIO + bool "U2/Uturn I/O MMU" + depends on GSC + help + Say Y here to enable DMA management routines for the first + generation of PA-RISC cache-coherent machines. Programs the + U2/Uturn chip in "Virtual Mode" and use the I/O MMU. + +config GSC_LASI + bool "Lasi I/O support" + depends on GSC + help + Say Y here to support the Lasi multifunction chip found in + many PA-RISC workstations & servers. It includes interfaces + for a parallel port, serial port, NCR 53c710 SCSI, Apricot + Ethernet, Harmony audio, PS/2 keyboard & mouse, ISDN, telephony + and floppy. Note that you must still enable all the individual + drivers for these chips. + +config GSC_WAX + bool "Wax I/O support" + depends on GSC + help + Say Y here to support the Wax multifunction chip found in some + older systems, including B/C/D/R class and 715/64, 715/80 and + 715/100. Wax includes an EISA adapter, a serial port (not always + used), a HIL interface chip and is also known to be used as the + GSC bridge for an X.25 GSC card. + +config EISA + bool "EISA support" + depends on GSC + help + Say Y here if you have an EISA bus in your machine. This code + supports both the Mongoose & Wax EISA adapters. It is sadly + incomplete and lacks support for card-to-host DMA. + +source "drivers/eisa/Kconfig" + +config ISA + bool "ISA support" + depends on EISA + help + If you want to plug an ISA card into your EISA bus, say Y here. + Most people should say N. + +config PCI + bool "PCI support" + help + All recent HP machines have PCI slots, and you should say Y here + if you have a recent machine. If you are convinced you do not have + PCI slots in your machine (eg a 712), then you may say "N" here. + Beware that some GSC cards have a Dino onboard and PCI inside them, + so it may be safest to say "Y" anyway. + +source "drivers/pci/Kconfig" + +config GSC_DINO + bool "GSCtoPCI/Dino PCI support" + depends on PCI && GSC + help + Say Y here to support the Dino & Cujo GSC to PCI bridges found in + machines from the B132 to the C360, the J2240 and the A180. Some + GSC/HSC cards (eg gigabit & dual 100 Mbit Ethernet) have a Dino on + the card, and you also need to say Y here if you have such a card. + Note that Dino also supplies one of the serial ports on certain + machines. If in doubt, say Y. + +config PCI_LBA + bool "LBA/Elroy PCI support" + depends on PCI + help + Say Y here to support the Elroy PCI Lower Bus Adapter. This is + present on B, C, J, L and N-class machines with 4-digit model + numbers and the A400/A500. + +config IOSAPIC + bool + depends on PCI_LBA + default PCI_LBA + +config IOMMU_SBA + bool + depends on PCI_LBA + default PCI_LBA + +source "drivers/pcmcia/Kconfig" + +endmenu + +menu "PA-RISC specific drivers" + +config SUPERIO + bool "SuperIO (SuckyIO) support" + depends on PCI_LBA + default y + help + Say Y here to support the SuperIO chip found in Bxxxx, C3xxx and + J5xxx+ machines. This enables IDE, Floppy, Parallel Port, and + Serial port on those machines. + +config CHASSIS_LCD_LED + bool "Chassis LCD and LED support" + default y + select VM_EVENT_COUNTERS + help + Say Y here if you want to enable support for the Heartbeat, + Disk/Network activities LEDs on some PA-RISC machines, + or support for the LCD that can be found on recent material. + + This has nothing to do with LED State support for A and E class. + + If unsure, say Y. + +config PDC_CHASSIS + bool "PDC chassis state codes support" + default y + help + Say Y here if you want to enable support for Chassis codes. + That includes support for LED State front panel as found on E + class, and support for the GSP Virtual Front Panel (LED State and + message logging) as found on high end servers such as A, L and + N-class. + This driver will also display progress messages on LCD display, + such as "INI", "RUN" and "FLT", and might thus clobber messages + shown by the LED/LCD driver. + This driver updates the state panel (LED and/or LCD) upon system + state change (eg: boot, shutdown or panic). + + If unsure, say Y. + + +config PDC_CHASSIS_WARN + bool "PDC chassis warnings support" + depends on PROC_FS + default y + help + Say Y here if you want to enable support for Chassis warnings. + This will add a proc entry '/proc/chassis' giving some information + about the overall health state of the system. + This includes NVRAM battery level, overtemp or failures such as + fans or power units. + + If unsure, say Y. + + +config PDC_STABLE + tristate "PDC Stable Storage support" + depends on SYSFS + default y + help + Say Y here if you want to enable support for accessing Stable Storage + variables (PDC non volatile variables such as Primary Boot Path, + Console Path, Autoboot, Autosearch, etc) through SysFS. + + If unsure, say Y. + + To compile this driver as a module, choose M here. + The module will be called pdc_stable. + +endmenu |