From 76cb841cb886eef6b3bee341a2266c76578724ad Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Mon, 6 May 2024 03:02:30 +0200 Subject: Adding upstream version 4.19.249. Signed-off-by: Daniel Baumann --- .../devicetree/bindings/phy/phy-miphy365x.txt | 77 ++++++++++++++++++++++ 1 file changed, 77 insertions(+) create mode 100644 Documentation/devicetree/bindings/phy/phy-miphy365x.txt (limited to 'Documentation/devicetree/bindings/phy/phy-miphy365x.txt') diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt new file mode 100644 index 000000000..8772900e0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt @@ -0,0 +1,77 @@ +STMicroelectronics STi MIPHY365x PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA and PCIe. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy365x-phy" +- st,syscfg : Phandle / integer array property. Phandle of sysconfig group + containing the miphy registers and integer array should contain + an entry for each port sub-node, specifying the control + register offset inside the sysconfig group. + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - PHY_TYPE_SATA + - PHY_TYPE_PCI +- reg : Address and length of register sets for each device in + "reg-names" +- reg-names : The names of the register addresses corresponding to the + registers filled in "reg": + - sata: For SATA devices + - pcie: For PCIe devices + +Optional properties (port (child) node): +- st,sata-gen : Generation of locally attached SATA IP. Expected values + are {1,2,3). If not supplied generation 1 hardware will + be expected +- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp) +- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp) + +Example: + + miphy365x_phy: miphy365x@fe382000 { + compatible = "st,miphy365x-phy"; + st,syscfg = <&syscfg_rear 0x824 0x828>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@fe382000 { + reg = <0xfe382000 0x100>, <0xfe394000 0x100>; + reg-names = "sata", "pcie"; + #phy-cells = <1>; + st,sata-gen = <3>; + }; + + phy_port1: port@fe38a000 { + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;; + reg-names = "sata", "pcie", "syscfg"; + #phy-cells = <1>; + st,pcie-tx-pol-inv; + }; + }; + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type. + +Example: + +#include + + sata0: sata@fe380000 { + ... + phys = <&phy_port0 PHY_TYPE_SATA>; + ... + }; -- cgit v1.2.3