Adding upstream version 2.8.0+dfsg.upstream/2.8.0+dfsgupstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 2528 insertions, 0 deletions

diff --git a/drivers/marvell/comphy/phy-comphy-cp110.c b/drivers/marvell/comphy/phy-comphy-cp110.c
new file mode 100644
index 0000000..fa9fe41
--- /dev/null
+++ b/drivers/marvell/comphy/phy-comphy-cp110.c
@@ -0,0 +1,2528 @@
+/*
+ * Copyright (C) 2018 Marvell International Ltd.
+ *
+ * SPDX-License-Identifier:     BSD-3-Clause
+ * https://spdx.org/licenses
+ */
+
+/* Marvell CP110 SoC COMPHY unit driver */
+
+#include <errno.h>
+#include <inttypes.h>
+#include <stdint.h>
+
+#include <common/debug.h>
+#include <drivers/delay_timer.h>
+#include <mg_conf_cm3/mg_conf_cm3.h>
+#include <lib/mmio.h>
+#include <lib/spinlock.h>
+
+#include <mvebu_def.h>
+#include "mvebu.h"
+#include "comphy-cp110.h"
+#include "phy-comphy-cp110.h"
+#include "phy-comphy-common.h"
+
+#if __has_include("phy-porting-layer.h")
+#include "phy-porting-layer.h"
+#else
+#include "phy-default-porting-layer.h"
+#endif
+
+/* COMPHY speed macro */
+#define COMPHY_SPEED_1_25G		0 /* SGMII 1G */
+#define COMPHY_SPEED_2_5G		1
+#define COMPHY_SPEED_3_125G		2 /* 2500Base-X */
+#define COMPHY_SPEED_5G			3
+#define COMPHY_SPEED_5_15625G		4 /* XFI 5G */
+#define COMPHY_SPEED_6G			5
+#define COMPHY_SPEED_10_3125G		6 /* XFI 10G */
+#define COMPHY_SPEED_MAX		0x3F
+/* The  default speed for IO with fixed known speed */
+#define COMPHY_SPEED_DEFAULT		COMPHY_SPEED_MAX
+
+/* Commands for comphy driver */
+#define COMPHY_COMMAND_DIGITAL_PWR_OFF		0x00000001
+#define COMPHY_COMMAND_DIGITAL_PWR_ON		0x00000002
+
+#define COMPHY_PIPE_FROM_COMPHY_ADDR(x)	((x & ~0xffffff) + 0x120000)
+
+/* System controller registers */
+#define PCIE_MAC_RESET_MASK_PORT0	BIT(13)
+#define PCIE_MAC_RESET_MASK_PORT1	BIT(11)
+#define PCIE_MAC_RESET_MASK_PORT2	BIT(12)
+#define SYS_CTRL_UINIT_SOFT_RESET_REG	0x268
+#define SYS_CTRL_FROM_COMPHY_ADDR(x)	((x & ~0xffffff) + 0x440000)
+
+/* DFX register spaces */
+#define SAR_RST_PCIE0_CLOCK_CONFIG_CP0_OFFSET	(30)
+#define SAR_RST_PCIE0_CLOCK_CONFIG_CP0_MASK	(0x1UL << \
+					SAR_RST_PCIE0_CLOCK_CONFIG_CP0_OFFSET)
+#define SAR_RST_PCIE1_CLOCK_CONFIG_CP0_OFFSET	(31)
+#define SAR_RST_PCIE1_CLOCK_CONFIG_CP0_MASK	(0x1UL << \
+					SAR_RST_PCIE1_CLOCK_CONFIG_CP0_OFFSET)
+#define SAR_STATUS_0_REG			0x40600
+#define DFX_FROM_COMPHY_ADDR(x)			((x & ~0xffffff) + DFX_BASE)
+/* Common Phy training  */
+#define COMPHY_TRX_TRAIN_COMPHY_OFFS		0x1000
+#define COMPHY_TRX_TRAIN_RX_TRAIN_ENABLE	0x1
+#define COMPHY_TRX_RELATIVE_ADDR(comphy_index)	(comphy_train_base + \
+			(comphy_index) * COMPHY_TRX_TRAIN_COMPHY_OFFS)
+
+/* The same Units Soft Reset Config register are accessed in all PCIe ports
+ * initialization, so a spin lock is defined in case when more than 1 CPUs
+ * resets PCIe MAC and need to access the register in the same time. The spin
+ * lock is shared by all CP110 units.
+ */
+spinlock_t cp110_mac_reset_lock;
+
+/* These values come from the PCI Express Spec */
+enum pcie_link_width {
+	PCIE_LNK_WIDTH_RESRV	= 0x00,
+	PCIE_LNK_X1		= 0x01,
+	PCIE_LNK_X2		= 0x02,
+	PCIE_LNK_X4		= 0x04,
+	PCIE_LNK_X8		= 0x08,
+	PCIE_LNK_X12		= 0x0C,
+	PCIE_LNK_X16		= 0x10,
+	PCIE_LNK_X32		= 0x20,
+	PCIE_LNK_WIDTH_UNKNOWN  = 0xFF,
+};
+
+_Bool rx_trainng_done[AP_NUM][CP_NUM][MAX_LANE_NR] = {0};
+
+static void mvebu_cp110_get_ap_and_cp_nr(uint8_t *ap_nr, uint8_t *cp_nr,
+					 uint64_t comphy_base)
+{
+#if (AP_NUM == 1)
+	*ap_nr = 0;
+#else
+	*ap_nr = (((comphy_base & ~0xffffff) - MVEBU_AP_IO_BASE(0)) /
+			 AP_IO_OFFSET);
+#endif
+
+	*cp_nr = (((comphy_base & ~0xffffff) - MVEBU_AP_IO_BASE(*ap_nr)) /
+		 MVEBU_CP_OFFSET);
+
+	debug("cp_base 0x%" PRIx64 ", ap_io_base 0x%lx, cp_offset 0x%lx\n",
+	       comphy_base, (unsigned long)MVEBU_AP_IO_BASE(*ap_nr),
+	       (unsigned long)MVEBU_CP_OFFSET);
+}
+
+/* Clear PIPE selector - avoid collision with previous configuration */
+static void mvebu_cp110_comphy_clr_pipe_selector(uint64_t comphy_base,
+						 uint8_t comphy_index)
+{
+	uint32_t reg, mask, field;
+	uint32_t comphy_offset =
+			COMMON_SELECTOR_COMPHYN_FIELD_WIDTH * comphy_index;
+
+	mask = COMMON_SELECTOR_COMPHY_MASK << comphy_offset;
+	reg = mmio_read_32(comphy_base + COMMON_SELECTOR_PIPE_REG_OFFSET);
+	field = reg & mask;
+
+	if (field) {
+		reg &= ~mask;
+		mmio_write_32(comphy_base + COMMON_SELECTOR_PIPE_REG_OFFSET,
+			     reg);
+	}
+}
+
+/* Clear PHY selector - avoid collision with previous configuration */
+static void mvebu_cp110_comphy_clr_phy_selector(uint64_t comphy_base,
+						uint8_t comphy_index)
+{
+	uint32_t reg, mask, field;
+	uint32_t comphy_offset =
+			COMMON_SELECTOR_COMPHYN_FIELD_WIDTH * comphy_index;
+
+	mask = COMMON_SELECTOR_COMPHY_MASK << comphy_offset;
+	reg = mmio_read_32(comphy_base + COMMON_SELECTOR_PHY_REG_OFFSET);
+	field = reg & mask;
+
+	/* Clear comphy selector - if it was already configured.
+	 * (might be that this comphy was configured as PCIe/USB,
+	 * in such case, no need to clear comphy selector because PCIe/USB
+	 * are controlled by hpipe selector).
+	 */
+	if (field) {
+		reg &= ~mask;
+		mmio_write_32(comphy_base + COMMON_SELECTOR_PHY_REG_OFFSET,
+			      reg);
+	}
+}
+
+/* PHY selector configures SATA and Network modes */
+static void mvebu_cp110_comphy_set_phy_selector(uint64_t comphy_base,
+				     uint8_t comphy_index, uint32_t comphy_mode)
+{
+	uint32_t reg, mask;
+	uint32_t comphy_offset =
+			COMMON_SELECTOR_COMPHYN_FIELD_WIDTH * comphy_index;
+	int mode;
+
+	/* If phy selector is used the pipe selector should be marked as
+	 * unconnected.
+	 */
+	mvebu_cp110_comphy_clr_pipe_selector(comphy_base, comphy_index);
+
+	/* Comphy mode (compound of the IO mode and id). Here, only the IO mode
+	 * is required to distinguish between SATA and network modes.
+	 */
+	mode = COMPHY_GET_MODE(comphy_mode);
+
+	mask = COMMON_SELECTOR_COMPHY_MASK << comphy_offset;
+	reg = mmio_read_32(comphy_base + COMMON_SELECTOR_PHY_REG_OFFSET);
+	reg &= ~mask;
+
+	/* SATA port 0/1 require the same configuration */
+	if (mode == COMPHY_SATA_MODE) {
+		/* SATA selector values is always 4 */
+		reg |= COMMON_SELECTOR_COMPHYN_SATA << comphy_offset;
+	} else {
+		switch (comphy_index) {
+		case(0):
+		case(1):
+		case(2):
+			/* For comphy 0,1, and 2:
+			 * Network selector value is always 1.
+			 */
+			reg |= COMMON_SELECTOR_COMPHY0_1_2_NETWORK <<
+				comphy_offset;
+			break;
+		case(3):
+			/* For comphy 3:
+			 * 0x1 = RXAUI_Lane1
+			 * 0x2 = SGMII/Base-X Port1
+			 */
+			if (mode == COMPHY_RXAUI_MODE)
+				reg |= COMMON_SELECTOR_COMPHY3_RXAUI <<
+					comphy_offset;
+			else
+				reg |= COMMON_SELECTOR_COMPHY3_SGMII <<
+					comphy_offset;
+			break;
+		case(4):
+			 /* For comphy 4:
+			  * 0x1 = SGMII/Base-X Port1, XFI1/SFI1
+			  * 0x2 = SGMII/Base-X Port0: XFI0/SFI0, RXAUI_Lane0
+			  *
+			  * We want to check if SGMII1 is the
+			  * requested mode in order to determine which value
+			  * should be set (all other modes use the same value)
+			  * so we need to strip the mode, and check the ID
+			  * because we might handle SGMII0 too.
+			  */
+			  /* TODO: need to distinguish between CP110 and CP115
+			   * as SFI1/XFI1 available only for CP115.
+			   */
+			if ((mode == COMPHY_SGMII_MODE ||
+			     mode == COMPHY_2500BASEX_MODE ||
+			     mode == COMPHY_SFI_MODE ||
+			     mode == COMPHY_XFI_MODE ||
+			     mode == COMPHY_AP_MODE)
+			    && COMPHY_GET_ID(comphy_mode) == 1)
+				reg |= COMMON_SELECTOR_COMPHY4_PORT1 <<
+					comphy_offset;
+			else
+				reg |= COMMON_SELECTOR_COMPHY4_ALL_OTHERS <<
+					comphy_offset;
+			break;
+		case(5):
+			/* For comphy 5:
+			 * 0x1 = SGMII/Base-X Port2
+			 * 0x2 = RXAUI Lane1
+			 */
+			if (mode == COMPHY_RXAUI_MODE)
+				reg |= COMMON_SELECTOR_COMPHY5_RXAUI <<
+					comphy_offset;
+			else
+				reg |= COMMON_SELECTOR_COMPHY5_SGMII <<
+					comphy_offset;
+			break;
+		}
+	}
+
+	mmio_write_32(comphy_base + COMMON_SELECTOR_PHY_REG_OFFSET, reg);
+}
+
+/* PIPE selector configures for PCIe, USB 3.0 Host, and USB 3.0 Device mode */
+static void mvebu_cp110_comphy_set_pipe_selector(uint64_t comphy_base,
+				     uint8_t comphy_index, uint32_t comphy_mode)
+{
+	uint32_t reg;
+	uint32_t shift = COMMON_SELECTOR_COMPHYN_FIELD_WIDTH * comphy_index;
+	int mode = COMPHY_GET_MODE(comphy_mode);
+	uint32_t mask = COMMON_SELECTOR_COMPHY_MASK << shift;
+	uint32_t pipe_sel = 0x0;
+
+	/* If pipe selector is used the phy selector should be marked as
+	 * unconnected.
+	 */
+	mvebu_cp110_comphy_clr_phy_selector(comphy_base, comphy_index);
+
+	reg = mmio_read_32(comphy_base + COMMON_SELECTOR_PIPE_REG_OFFSET);
+	reg &= ~mask;
+
+	switch (mode) {
+	case (COMPHY_PCIE_MODE):
+		/* For lanes support PCIE, selector value are all same */
+		pipe_sel = COMMON_SELECTOR_PIPE_COMPHY_PCIE;
+		break;
+
+	case (COMPHY_USB3H_MODE):
+		/* Only lane 1-4 support USB host, selector value is same */
+		if (comphy_index == COMPHY_LANE0 ||
+		    comphy_index == COMPHY_LANE5)
+			ERROR("COMPHY[%d] mode[%d] is invalid\n",
+			      comphy_index, mode);
+		else
+			pipe_sel = COMMON_SELECTOR_PIPE_COMPHY_USBH;
+		break;
+
+	case (COMPHY_USB3D_MODE):
+		/* Lane 1 and 4 support USB device, selector value is same */
+		if (comphy_index == COMPHY_LANE1 ||
+		    comphy_index == COMPHY_LANE4)
+			pipe_sel = COMMON_SELECTOR_PIPE_COMPHY_USBD;
+		else
+			ERROR("COMPHY[%d] mode[%d] is invalid\n", comphy_index,
+			      mode);
+		break;
+
+	default:
+		ERROR("COMPHY[%d] mode[%d] is invalid\n", comphy_index, mode);
+		break;
+	}
+
+	mmio_write_32(comphy_base + COMMON_SELECTOR_PIPE_REG_OFFSET, reg |
+		      (pipe_sel << shift));
+}
+
+int mvebu_cp110_comphy_is_pll_locked(uint64_t comphy_base, uint8_t comphy_index)
+{
+	uintptr_t sd_ip_addr, addr;
+	uint32_t mask, data;
+	int ret = 0;
+
+	debug_enter();
+
+	sd_ip_addr = SD_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+			     comphy_index);
+
+	addr = sd_ip_addr + SD_EXTERNAL_STATUS0_REG;
+	data = SD_EXTERNAL_STATUS0_PLL_TX_MASK &
+		SD_EXTERNAL_STATUS0_PLL_RX_MASK;
+	mask = data;
+	data = polling_with_timeout(addr, data, mask,
+				    PLL_LOCK_TIMEOUT, REG_32BIT);
+	if (data != 0) {
+		if (data & SD_EXTERNAL_STATUS0_PLL_RX_MASK)
+			ERROR("RX PLL is not locked\n");
+		if (data & SD_EXTERNAL_STATUS0_PLL_TX_MASK)
+			ERROR("TX PLL is not locked\n");
+
+		ret = -ETIMEDOUT;
+	}
+
+	debug_exit();
+
+	return ret;
+}
+
+static void mvebu_cp110_polarity_invert(uintptr_t addr, uint8_t phy_polarity_invert)
+{
+	uint32_t mask, data;
+
+	/* Set RX / TX polarity */
+	data = mask = 0x0U;
+	if ((phy_polarity_invert & COMPHY_POLARITY_TXD_INVERT) != 0) {
+		data |= (1 << HPIPE_SYNC_PATTERN_TXD_INV_OFFSET);
+		mask |= HPIPE_SYNC_PATTERN_TXD_INV_MASK;
+		debug("%s: inverting TX polarity\n", __func__);
+	}
+
+	if ((phy_polarity_invert & COMPHY_POLARITY_RXD_INVERT) != 0) {
+		data |= (1 << HPIPE_SYNC_PATTERN_RXD_INV_OFFSET);
+		mask |= HPIPE_SYNC_PATTERN_RXD_INV_MASK;
+		debug("%s: inverting RX polarity\n", __func__);
+	}
+
+	reg_set(addr, data, mask);
+}
+
+static int mvebu_cp110_comphy_sata_power_on(uint64_t comphy_base,
+				     uint8_t comphy_index, uint32_t comphy_mode)
+{
+	uintptr_t hpipe_addr, sd_ip_addr, comphy_addr;
+	uint32_t mask, data;
+	uint8_t ap_nr, cp_nr, phy_polarity_invert;
+	int ret = 0;
+
+	debug_enter();
+
+	mvebu_cp110_get_ap_and_cp_nr(&ap_nr, &cp_nr, comphy_base);
+
+	const struct sata_params *sata_static_values =
+			&sata_static_values_tab[ap_nr][cp_nr][comphy_index];
+
+	phy_polarity_invert = sata_static_values->polarity_invert;
+
+	/* configure phy selector for SATA */
+	mvebu_cp110_comphy_set_phy_selector(comphy_base,
+					    comphy_index, comphy_mode);
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+	sd_ip_addr = SD_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+			     comphy_index);
+	comphy_addr = COMPHY_ADDR(comphy_base, comphy_index);
+
+	debug(" add hpipe 0x%lx, sd 0x%lx, comphy 0x%lx\n",
+					   hpipe_addr, sd_ip_addr, comphy_addr);
+	debug("stage: RFU configurations - hard reset comphy\n");
+	/* RFU configurations - hard reset comphy */
+	mask = COMMON_PHY_CFG1_PWR_UP_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_UP_OFFSET;
+	mask |= COMMON_PHY_CFG1_PIPE_SELECT_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PIPE_SELECT_OFFSET;
+	mask |= COMMON_PHY_CFG1_PWR_ON_RESET_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PWR_ON_RESET_OFFSET;
+	mask |= COMMON_PHY_CFG1_CORE_RSTN_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_CORE_RSTN_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* Set select data  width 40Bit - SATA mode only */
+	reg_set(comphy_addr + COMMON_PHY_CFG6_REG,
+		0x1 << COMMON_PHY_CFG6_IF_40_SEL_OFFSET,
+		COMMON_PHY_CFG6_IF_40_SEL_MASK);
+
+	/* release from hard reset in SD external */
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* Wait 1ms - until band gap and ref clock ready */
+	mdelay(1);
+
+	debug("stage: Comphy configuration\n");
+	/* Start comphy Configuration */
+	/* Set reference clock to comes from group 1 - choose 25Mhz */
+	reg_set(hpipe_addr + HPIPE_MISC_REG,
+		0x0 << HPIPE_MISC_REFCLK_SEL_OFFSET,
+		HPIPE_MISC_REFCLK_SEL_MASK);
+	/* Reference frequency select set 1 (for SATA = 25Mhz) */
+	mask = HPIPE_PWR_PLL_REF_FREQ_MASK;
+	data = 0x1 << HPIPE_PWR_PLL_REF_FREQ_OFFSET;
+	/* PHY mode select (set SATA = 0x0 */
+	mask |= HPIPE_PWR_PLL_PHY_MODE_MASK;
+	data |= 0x0 << HPIPE_PWR_PLL_PHY_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_PLL_REG, data, mask);
+	/* Set max PHY generation setting - 6Gbps */
+	reg_set(hpipe_addr + HPIPE_INTERFACE_REG,
+		0x2 << HPIPE_INTERFACE_GEN_MAX_OFFSET,
+		HPIPE_INTERFACE_GEN_MAX_MASK);
+	/* Set select data  width 40Bit (SEL_BITS[2:0]) */
+	reg_set(hpipe_addr + HPIPE_LOOPBACK_REG,
+		0x2 << HPIPE_LOOPBACK_SEL_OFFSET, HPIPE_LOOPBACK_SEL_MASK);
+
+	debug("stage: Analog parameters from ETP(HW)\n");
+	/* G1 settings */
+	mask = HPIPE_G1_SET_1_G1_RX_SELMUPI_MASK;
+	data = sata_static_values->g1_rx_selmupi <<
+			HPIPE_G1_SET_1_G1_RX_SELMUPI_OFFSET;
+	mask |= HPIPE_G1_SET_1_G1_RX_SELMUPF_MASK;
+	data |= sata_static_values->g1_rx_selmupf <<
+			HPIPE_G1_SET_1_G1_RX_SELMUPF_OFFSET;
+	mask |= HPIPE_G1_SET_1_G1_RX_SELMUFI_MASK;
+	data |= sata_static_values->g1_rx_selmufi <<
+			HPIPE_G1_SET_1_G1_RX_SELMUFI_OFFSET;
+	mask |= HPIPE_G1_SET_1_G1_RX_SELMUFF_MASK;
+	data |= sata_static_values->g1_rx_selmuff <<
+			HPIPE_G1_SET_1_G1_RX_SELMUFF_OFFSET;
+	mask |= HPIPE_G1_SET_1_G1_RX_DIGCK_DIV_MASK;
+	data |= 0x1 << HPIPE_G1_SET_1_G1_RX_DIGCK_DIV_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SET_1_REG, data, mask);
+
+	mask = HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_MASK;
+	data = 0xf << HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_OFFSET;
+	mask |= HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_MASK;
+	data |= 0x2 << HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_OFFSET;
+	mask |= HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_MASK;
+	data |= 0x1 << HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_OFFSET;
+	mask |= HPIPE_G1_SETTINGS_3_G1_FFE_DEG_RES_LEVEL_MASK;
+	data |= 0x1 << HPIPE_G1_SETTINGS_3_G1_FFE_DEG_RES_LEVEL_OFFSET;
+	mask |= HPIPE_G1_SETTINGS_3_G1_FFE_LOAD_RES_LEVEL_MASK;
+	data |= 0x1 << HPIPE_G1_SETTINGS_3_G1_FFE_LOAD_RES_LEVEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_3_REG, data, mask);
+
+	/* G2 settings */
+	mask = HPIPE_G2_SET_1_G2_RX_SELMUPI_MASK;
+	data = sata_static_values->g2_rx_selmupi <<
+			HPIPE_G2_SET_1_G2_RX_SELMUPI_OFFSET;
+	mask |= HPIPE_G2_SET_1_G2_RX_SELMUPF_MASK;
+	data |= sata_static_values->g2_rx_selmupf <<
+			HPIPE_G2_SET_1_G2_RX_SELMUPF_OFFSET;
+	mask |= HPIPE_G2_SET_1_G2_RX_SELMUFI_MASK;
+	data |= sata_static_values->g2_rx_selmufi <<
+			HPIPE_G2_SET_1_G2_RX_SELMUFI_OFFSET;
+	mask |= HPIPE_G2_SET_1_G2_RX_SELMUFF_MASK;
+	data |= sata_static_values->g2_rx_selmuff <<
+			HPIPE_G2_SET_1_G2_RX_SELMUFF_OFFSET;
+	mask |= HPIPE_G2_SET_1_G2_RX_DIGCK_DIV_MASK;
+	data |= 0x1 << HPIPE_G2_SET_1_G2_RX_DIGCK_DIV_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G2_SET_1_REG, data, mask);
+
+	/* G3 settings */
+	mask = HPIPE_G3_SET_1_G3_RX_SELMUPI_MASK;
+	data = sata_static_values->g3_rx_selmupi <<
+			HPIPE_G3_SET_1_G3_RX_SELMUPI_OFFSET;
+	mask |= HPIPE_G3_SET_1_G3_RX_SELMUPF_MASK;
+	data |= sata_static_values->g3_rx_selmupf <<
+			HPIPE_G3_SET_1_G3_RX_SELMUPF_OFFSET;
+	mask |= HPIPE_G3_SET_1_G3_RX_SELMUFI_MASK;
+	data |= sata_static_values->g3_rx_selmufi <<
+			HPIPE_G3_SET_1_G3_RX_SELMUFI_OFFSET;
+	mask |= HPIPE_G3_SET_1_G3_RX_SELMUFF_MASK;
+	data |= sata_static_values->g3_rx_selmuff <<
+			HPIPE_G3_SET_1_G3_RX_SELMUFF_OFFSET;
+	mask |= HPIPE_G3_SET_1_G3_RX_DFE_EN_MASK;
+	data |= 0x1 << HPIPE_G3_SET_1_G3_RX_DFE_EN_OFFSET;
+	mask |= HPIPE_G3_SET_1_G3_RX_DIGCK_DIV_MASK;
+	data |= 0x2 << HPIPE_G3_SET_1_G3_RX_DIGCK_DIV_OFFSET;
+	mask |= HPIPE_G3_SET_1_G3_SAMPLER_INPAIRX2_EN_MASK;
+	data |= 0x0 << HPIPE_G3_SET_1_G3_SAMPLER_INPAIRX2_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SET_1_REG, data, mask);
+
+	/* DTL Control */
+	mask = HPIPE_PWR_CTR_DTL_SQ_DET_EN_MASK;
+	data = 0x1 << HPIPE_PWR_CTR_DTL_SQ_DET_EN_OFFSET;
+	mask |= HPIPE_PWR_CTR_DTL_SQ_PLOOP_EN_MASK;
+	data |= 0x1 << HPIPE_PWR_CTR_DTL_SQ_PLOOP_EN_OFFSET;
+	mask |= HPIPE_PWR_CTR_DTL_FLOOP_EN_MASK;
+	data |= 0x1 << HPIPE_PWR_CTR_DTL_FLOOP_EN_OFFSET;
+	mask |= HPIPE_PWR_CTR_DTL_CLAMPING_SEL_MASK;
+	data |= 0x1 << HPIPE_PWR_CTR_DTL_CLAMPING_SEL_OFFSET;
+	mask |= HPIPE_PWR_CTR_DTL_INTPCLK_DIV_FORCE_MASK;
+	data |= 0x1 << HPIPE_PWR_CTR_DTL_INTPCLK_DIV_FORCE_OFFSET;
+	mask |= HPIPE_PWR_CTR_DTL_CLK_MODE_MASK;
+	data |= 0x1 << HPIPE_PWR_CTR_DTL_CLK_MODE_OFFSET;
+	mask |= HPIPE_PWR_CTR_DTL_CLK_MODE_FORCE_MASK;
+	data |= 0x1 << HPIPE_PWR_CTR_DTL_CLK_MODE_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_DTL_REG, data, mask);
+
+	/* Trigger sampler enable pulse */
+	mask = HPIPE_SMAPLER_MASK;
+	data = 0x1 << HPIPE_SMAPLER_OFFSET;
+	reg_set(hpipe_addr + HPIPE_SAMPLER_N_PROC_CALIB_CTRL_REG, data, mask);
+	mask = HPIPE_SMAPLER_MASK;
+	data = 0x0 << HPIPE_SMAPLER_OFFSET;
+	reg_set(hpipe_addr + HPIPE_SAMPLER_N_PROC_CALIB_CTRL_REG, data, mask);
+
+	/* VDD Calibration Control 3 */
+	mask = HPIPE_EXT_SELLV_RXSAMPL_MASK;
+	data = 0x10 << HPIPE_EXT_SELLV_RXSAMPL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_VDD_CAL_CTRL_REG, data, mask);
+
+	/* DFE Resolution Control */
+	mask = HPIPE_DFE_RES_FORCE_MASK;
+	data = 0x1 << HPIPE_DFE_RES_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_REG0, data, mask);
+
+	/* DFE F3-F5 Coefficient Control */
+	mask = HPIPE_DFE_F3_F5_DFE_EN_MASK;
+	data = 0x0 << HPIPE_DFE_F3_F5_DFE_EN_OFFSET;
+	mask |= HPIPE_DFE_F3_F5_DFE_CTRL_MASK;
+	data = 0x0 << HPIPE_DFE_F3_F5_DFE_CTRL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_F3_F5_REG, data, mask);
+
+	/* G3 Setting 3 */
+	mask = HPIPE_G3_FFE_CAP_SEL_MASK;
+	data = sata_static_values->g3_ffe_cap_sel <<
+			HPIPE_G3_FFE_CAP_SEL_OFFSET;
+	mask |= HPIPE_G3_FFE_RES_SEL_MASK;
+	data |= sata_static_values->g3_ffe_res_sel <<
+			HPIPE_G3_FFE_RES_SEL_OFFSET;
+	mask |= HPIPE_G3_FFE_SETTING_FORCE_MASK;
+	data |= 0x1 << HPIPE_G3_FFE_SETTING_FORCE_OFFSET;
+	mask |= HPIPE_G3_FFE_DEG_RES_LEVEL_MASK;
+	data |= 0x1 << HPIPE_G3_FFE_DEG_RES_LEVEL_OFFSET;
+	mask |= HPIPE_G3_FFE_LOAD_RES_LEVEL_MASK;
+	data |= 0x3 << HPIPE_G3_FFE_LOAD_RES_LEVEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SETTING_3_REG, data, mask);
+
+	/* G3 Setting 4 */
+	mask = HPIPE_G3_DFE_RES_MASK;
+	data = sata_static_values->g3_dfe_res << HPIPE_G3_DFE_RES_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SETTING_4_REG, data, mask);
+
+	/* Offset Phase Control */
+	mask = HPIPE_OS_PH_OFFSET_MASK;
+	data = sata_static_values->align90 << HPIPE_OS_PH_OFFSET_OFFSET;
+	mask |= HPIPE_OS_PH_OFFSET_FORCE_MASK;
+	data |= 0x1 << HPIPE_OS_PH_OFFSET_FORCE_OFFSET;
+	mask |= HPIPE_OS_PH_VALID_MASK;
+	data |= 0x0 << HPIPE_OS_PH_VALID_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PHASE_CONTROL_REG, data, mask);
+	mask = HPIPE_OS_PH_VALID_MASK;
+	data = 0x1 << HPIPE_OS_PH_VALID_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PHASE_CONTROL_REG, data, mask);
+	mask = HPIPE_OS_PH_VALID_MASK;
+	data = 0x0 << HPIPE_OS_PH_VALID_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PHASE_CONTROL_REG, data, mask);
+
+	/* Set G1 TX amplitude and TX post emphasis value */
+	mask = HPIPE_G1_SET_0_G1_TX_AMP_MASK;
+	data = sata_static_values->g1_amp << HPIPE_G1_SET_0_G1_TX_AMP_OFFSET;
+	mask |= HPIPE_G1_SET_0_G1_TX_AMP_ADJ_MASK;
+	data |= sata_static_values->g1_tx_amp_adj <<
+			HPIPE_G1_SET_0_G1_TX_AMP_ADJ_OFFSET;
+	mask |= HPIPE_G1_SET_0_G1_TX_EMPH1_MASK;
+	data |= sata_static_values->g1_emph <<
+			HPIPE_G1_SET_0_G1_TX_EMPH1_OFFSET;
+	mask |= HPIPE_G1_SET_0_G1_TX_EMPH1_EN_MASK;
+	data |= sata_static_values->g1_emph_en <<
+			HPIPE_G1_SET_0_G1_TX_EMPH1_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SET_0_REG, data, mask);
+
+	/* Set G1 emph */
+	mask = HPIPE_G1_SET_2_G1_TX_EMPH0_EN_MASK;
+	data = sata_static_values->g1_tx_emph_en <<
+			HPIPE_G1_SET_2_G1_TX_EMPH0_EN_OFFSET;
+	mask |= HPIPE_G1_SET_2_G1_TX_EMPH0_MASK;
+	data |= sata_static_values->g1_tx_emph <<
+			HPIPE_G1_SET_2_G1_TX_EMPH0_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SET_2_REG, data, mask);
+
+	/* Set G2 TX amplitude and TX post emphasis value */
+	mask = HPIPE_G2_SET_0_G2_TX_AMP_MASK;
+	data = sata_static_values->g2_amp << HPIPE_G2_SET_0_G2_TX_AMP_OFFSET;
+	mask |= HPIPE_G2_SET_0_G2_TX_AMP_ADJ_MASK;
+	data |= sata_static_values->g2_tx_amp_adj <<
+			HPIPE_G2_SET_0_G2_TX_AMP_ADJ_OFFSET;
+	mask |= HPIPE_G2_SET_0_G2_TX_EMPH1_MASK;
+	data |= sata_static_values->g2_emph <<
+			HPIPE_G2_SET_0_G2_TX_EMPH1_OFFSET;
+	mask |= HPIPE_G2_SET_0_G2_TX_EMPH1_EN_MASK;
+	data |= sata_static_values->g2_emph_en <<
+			HPIPE_G2_SET_0_G2_TX_EMPH1_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G2_SET_0_REG, data, mask);
+
+	/* Set G2 emph */
+	mask = HPIPE_G2_SET_2_G2_TX_EMPH0_EN_MASK;
+	data = sata_static_values->g2_tx_emph_en <<
+			HPIPE_G2_SET_2_G2_TX_EMPH0_EN_OFFSET;
+	mask |= HPIPE_G2_SET_2_G2_TX_EMPH0_MASK;
+	data |= sata_static_values->g2_tx_emph <<
+			HPIPE_G2_SET_2_G2_TX_EMPH0_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G2_SET_2_REG, data, mask);
+
+	/* Set G3 TX amplitude and TX post emphasis value */
+	mask = HPIPE_G3_SET_0_G3_TX_AMP_MASK;
+	data = sata_static_values->g3_amp << HPIPE_G3_SET_0_G3_TX_AMP_OFFSET;
+	mask |= HPIPE_G3_SET_0_G3_TX_AMP_ADJ_MASK;
+	data |= sata_static_values->g3_tx_amp_adj <<
+			HPIPE_G3_SET_0_G3_TX_AMP_ADJ_OFFSET;
+	mask |= HPIPE_G3_SET_0_G3_TX_EMPH1_MASK;
+	data |= sata_static_values->g3_emph <<
+			HPIPE_G3_SET_0_G3_TX_EMPH1_OFFSET;
+	mask |= HPIPE_G3_SET_0_G3_TX_EMPH1_EN_MASK;
+	data |= sata_static_values->g3_emph_en <<
+			HPIPE_G3_SET_0_G3_TX_EMPH1_EN_OFFSET;
+	mask |= HPIPE_G3_SET_0_G3_TX_SLEW_RATE_SEL_MASK;
+	data |= 0x4 << HPIPE_G3_SET_0_G3_TX_SLEW_RATE_SEL_OFFSET;
+	mask |= HPIPE_G3_SET_0_G3_TX_SLEW_CTRL_EN_MASK;
+	data |= 0x0 << HPIPE_G3_SET_0_G3_TX_SLEW_CTRL_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SET_0_REG, data, mask);
+
+	/* Set G3 emph */
+	mask = HPIPE_G3_SET_2_G3_TX_EMPH0_EN_MASK;
+	data = sata_static_values->g3_tx_emph_en <<
+			HPIPE_G3_SET_2_G3_TX_EMPH0_EN_OFFSET;
+	mask |= HPIPE_G3_SET_2_G3_TX_EMPH0_MASK;
+	data |= sata_static_values->g3_tx_emph <<
+			HPIPE_G3_SET_2_G3_TX_EMPH0_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SET_2_REG, data, mask);
+
+	/* SERDES External Configuration 2 register */
+	mask = SD_EXTERNAL_CONFIG2_SSC_ENABLE_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG2_SSC_ENABLE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG2_REG, data, mask);
+
+	/* DFE reset sequence */
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_REG,
+		0x1 << HPIPE_PWR_CTR_RST_DFE_OFFSET,
+		HPIPE_PWR_CTR_RST_DFE_MASK);
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_REG,
+		0x0 << HPIPE_PWR_CTR_RST_DFE_OFFSET,
+		HPIPE_PWR_CTR_RST_DFE_MASK);
+
+	if (phy_polarity_invert != 0)
+		mvebu_cp110_polarity_invert(hpipe_addr + HPIPE_SYNC_PATTERN_REG,
+					    phy_polarity_invert);
+
+	/* SW reset for interrupt logic */
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_REG,
+		0x1 << HPIPE_PWR_CTR_SFT_RST_OFFSET,
+		HPIPE_PWR_CTR_SFT_RST_MASK);
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_REG,
+		0x0 << HPIPE_PWR_CTR_SFT_RST_OFFSET,
+		HPIPE_PWR_CTR_SFT_RST_MASK);
+
+	debug_exit();
+
+	return ret;
+}
+
+static int mvebu_cp110_comphy_sgmii_power_on(uint64_t comphy_base,
+				     uint8_t comphy_index, uint32_t comphy_mode)
+{
+	uintptr_t hpipe_addr, sd_ip_addr, comphy_addr, addr;
+	uint32_t mask, data, sgmii_speed = COMPHY_GET_SPEED(comphy_mode);
+	int ret = 0;
+
+	debug_enter();
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+	sd_ip_addr = SD_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+			     comphy_index);
+	comphy_addr = COMPHY_ADDR(comphy_base, comphy_index);
+
+	/* configure phy selector for SGMII */
+	mvebu_cp110_comphy_set_phy_selector(comphy_base, comphy_index,
+					    comphy_mode);
+
+	/* Confiugre the lane */
+	debug("stage: RFU configurations - hard reset comphy\n");
+	/* RFU configurations - hard reset comphy */
+	mask = COMMON_PHY_CFG1_PWR_UP_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_UP_OFFSET;
+	mask |= COMMON_PHY_CFG1_PIPE_SELECT_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PIPE_SELECT_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* Select Baud Rate of Comphy And PD_PLL/Tx/Rx */
+	mask = SD_EXTERNAL_CONFIG0_SD_PU_PLL_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG0_SD_PU_PLL_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PHY_GEN_RX_MASK;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PHY_GEN_TX_MASK;
+
+	if (sgmii_speed == COMPHY_SPEED_1_25G) {
+		/* SGMII 1G, SerDes speed 1.25G */
+		data |= 0x6 << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_RX_OFFSET;
+		data |= 0x6 << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_TX_OFFSET;
+	} else if (sgmii_speed == COMPHY_SPEED_3_125G) {
+		/* 2500Base-X, SerDes speed 3.125G */
+		data |= 0x8 << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_RX_OFFSET;
+		data |= 0x8 << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_TX_OFFSET;
+	} else {
+		/* Other rates are not supported */
+		ERROR("unsupported SGMII speed on comphy%d\n", comphy_index);
+		return -EINVAL;
+	}
+
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_RX_MASK;
+	data |= 0 << SD_EXTERNAL_CONFIG0_SD_PU_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_TX_MASK;
+	data |= 0 << SD_EXTERNAL_CONFIG0_SD_PU_TX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_HALF_BUS_MODE_MASK;
+	data |= 1 << SD_EXTERNAL_CONFIG0_HALF_BUS_MODE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG0_REG, data, mask);
+
+	/* Set hard reset */
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* Release hard reset */
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* Wait 1ms - until band gap and ref clock ready */
+	mdelay(1);
+
+	/* Make sure that 40 data bits is disabled
+	 * This bit is not cleared by reset
+	 */
+	mask = COMMON_PHY_CFG6_IF_40_SEL_MASK;
+	data = 0 << COMMON_PHY_CFG6_IF_40_SEL_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG6_REG, data, mask);
+
+	/* Start comphy Configuration */
+	debug("stage: Comphy configuration\n");
+	/* set reference clock */
+	mask = HPIPE_MISC_REFCLK_SEL_MASK;
+	data = 0x0 << HPIPE_MISC_REFCLK_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_MISC_REG, data, mask);
+	/* Power and PLL Control */
+	mask = HPIPE_PWR_PLL_REF_FREQ_MASK;
+	data = 0x1 << HPIPE_PWR_PLL_REF_FREQ_OFFSET;
+	mask |= HPIPE_PWR_PLL_PHY_MODE_MASK;
+	data |= 0x4 << HPIPE_PWR_PLL_PHY_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_PLL_REG, data, mask);
+	/* Loopback register */
+	mask = HPIPE_LOOPBACK_SEL_MASK;
+	data = 0x1 << HPIPE_LOOPBACK_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_LOOPBACK_REG, data, mask);
+	/* rx control 1 */
+	mask = HPIPE_RX_CONTROL_1_RXCLK2X_SEL_MASK;
+	data = 0x1 << HPIPE_RX_CONTROL_1_RXCLK2X_SEL_OFFSET;
+	mask |= HPIPE_RX_CONTROL_1_CLK8T_EN_MASK;
+	data |= 0x0 << HPIPE_RX_CONTROL_1_CLK8T_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_RX_CONTROL_1_REG, data, mask);
+	/* DTL Control */
+	mask = HPIPE_PWR_CTR_DTL_FLOOP_EN_MASK;
+	data = 0x0 << HPIPE_PWR_CTR_DTL_FLOOP_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_DTL_REG, data, mask);
+
+	/* Set analog parameters from ETP(HW) - for now use the default data */
+	debug("stage: Analog parameters from ETP(HW)\n");
+
+	reg_set(hpipe_addr + HPIPE_G1_SET_0_REG,
+		0x1 << HPIPE_G1_SET_0_G1_TX_EMPH1_OFFSET,
+		HPIPE_G1_SET_0_G1_TX_EMPH1_MASK);
+
+	debug("stage: RFU configurations- Power Up PLL,Tx,Rx\n");
+	/* SERDES External Configuration */
+	mask = SD_EXTERNAL_CONFIG0_SD_PU_PLL_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_PLL_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_RX_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_TX_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_TX_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG0_REG, data, mask);
+
+	ret = mvebu_cp110_comphy_is_pll_locked(comphy_base, comphy_index);
+	if (ret)
+		return ret;
+
+	/* RX init */
+	mask = SD_EXTERNAL_CONFIG1_RX_INIT_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG1_RX_INIT_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* check that RX init done */
+	addr = sd_ip_addr + SD_EXTERNAL_STATUS0_REG;
+	data = SD_EXTERNAL_STATUS0_RX_INIT_MASK;
+	mask = data;
+	data = polling_with_timeout(addr, data, mask, 100, REG_32BIT);
+	if (data != 0) {
+		ERROR("RX init failed\n");
+		ret = -ETIMEDOUT;
+	}
+
+	debug("stage: RF Reset\n");
+	/* RF Reset */
+	mask = SD_EXTERNAL_CONFIG1_RX_INIT_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG1_RX_INIT_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	debug_exit();
+
+	return ret;
+}
+
+static int mvebu_cp110_comphy_xfi_power_on(uint64_t comphy_base,
+					   uint8_t comphy_index,
+					   uint32_t comphy_mode,
+					   uint64_t comphy_train_base)
+{
+	uintptr_t hpipe_addr, sd_ip_addr, comphy_addr, addr;
+	uint32_t mask, data, speed = COMPHY_GET_SPEED(comphy_mode);
+	int ret = 0;
+	uint8_t ap_nr, cp_nr;
+
+	debug_enter();
+	mvebu_cp110_get_ap_and_cp_nr(&ap_nr, &cp_nr, comphy_base);
+
+	if (rx_trainng_done[ap_nr][cp_nr][comphy_index]) {
+		debug("Skip %s for comphy[%d][%d][%d], due to rx training\n",
+		       __func__, ap_nr, cp_nr, comphy_index);
+		return 0;
+	}
+
+	const struct xfi_params *xfi_static_values =
+			     &xfi_static_values_tab[ap_nr][cp_nr][comphy_index];
+
+	debug("%s: the ap_nr = %d, cp_nr = %d, comphy_index %d\n",
+	      __func__, ap_nr, cp_nr, comphy_index);
+
+	debug("g1_ffe_cap_sel= 0x%x, g1_ffe_res_sel= 0x%x, g1_dfe_res= 0x%x\n",
+	      xfi_static_values->g1_ffe_cap_sel,
+	      xfi_static_values->g1_ffe_res_sel,
+	      xfi_static_values->g1_dfe_res);
+
+	if (!xfi_static_values->valid) {
+		ERROR("[ap%d][cp[%d][comphy:%d]: Has no valid static params\n",
+		      ap_nr, cp_nr, comphy_index);
+		ERROR("[ap%d][cp[%d][comphy:%d]: porting layer needs update\n",
+		      ap_nr, cp_nr, comphy_index);
+		return -EINVAL;
+	}
+
+	if ((speed != COMPHY_SPEED_5_15625G) &&
+	     (speed != COMPHY_SPEED_10_3125G) &&
+	     (speed != COMPHY_SPEED_DEFAULT)) {
+		ERROR("comphy:%d: unsupported sfi/xfi speed\n", comphy_index);
+		return -EINVAL;
+	}
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+	sd_ip_addr = SD_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+			     comphy_index);
+	comphy_addr = COMPHY_ADDR(comphy_base, comphy_index);
+
+	/* configure phy selector for XFI/SFI */
+	mvebu_cp110_comphy_set_phy_selector(comphy_base, comphy_index,
+					    comphy_mode);
+
+	debug("stage: RFU configurations - hard reset comphy\n");
+	/* RFU configurations - hard reset comphy */
+	mask = COMMON_PHY_CFG1_PWR_UP_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_UP_OFFSET;
+	mask |= COMMON_PHY_CFG1_PIPE_SELECT_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PIPE_SELECT_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* Make sure that 40 data bits is disabled
+	 * This bit is not cleared by reset
+	 */
+	mask = COMMON_PHY_CFG6_IF_40_SEL_MASK;
+	data = 0 << COMMON_PHY_CFG6_IF_40_SEL_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG6_REG, data, mask);
+
+	/* Select Baud Rate of Comphy And PD_PLL/Tx/Rx */
+	mask = SD_EXTERNAL_CONFIG0_SD_PU_PLL_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG0_SD_PU_PLL_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PHY_GEN_RX_MASK;
+	data |= 0xE << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PHY_GEN_TX_MASK;
+	data |= 0xE << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_TX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_RX_MASK;
+	data |= 0 << SD_EXTERNAL_CONFIG0_SD_PU_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_TX_MASK;
+	data |= 0 << SD_EXTERNAL_CONFIG0_SD_PU_TX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_HALF_BUS_MODE_MASK;
+	data |= 0 << SD_EXTERNAL_CONFIG0_HALF_BUS_MODE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG0_REG, data, mask);
+
+	/* release from hard reset */
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_TX_IDLE_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_TX_IDLE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* Wait 1ms - until band gap and ref clock ready */
+	mdelay(1);
+
+	/*
+	 * Erratum IPCE_COMPHY-1353: toggle TX_IDLE bit in
+	 * addition to the PHY reset
+	 */
+	mask = SD_EXTERNAL_CONFIG1_TX_IDLE_MASK;
+	data = 0x0U;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* Start comphy Configuration */
+	debug("stage: Comphy configuration\n");
+	/* set reference clock */
+	mask = HPIPE_MISC_ICP_FORCE_MASK;
+	data = (speed == COMPHY_SPEED_5_15625G) ?
+		(0x0 << HPIPE_MISC_ICP_FORCE_OFFSET) :
+		(0x1 << HPIPE_MISC_ICP_FORCE_OFFSET);
+	mask |= HPIPE_MISC_REFCLK_SEL_MASK;
+	data |= 0x0 << HPIPE_MISC_REFCLK_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_MISC_REG, data, mask);
+	/* Power and PLL Control */
+	mask = HPIPE_PWR_PLL_REF_FREQ_MASK;
+	data = 0x1 << HPIPE_PWR_PLL_REF_FREQ_OFFSET;
+	mask |= HPIPE_PWR_PLL_PHY_MODE_MASK;
+	data |= 0x4 << HPIPE_PWR_PLL_PHY_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_PLL_REG, data, mask);
+	/* Loopback register */
+	mask = HPIPE_LOOPBACK_SEL_MASK;
+	data = 0x1 << HPIPE_LOOPBACK_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_LOOPBACK_REG, data, mask);
+	/* rx control 1 */
+	mask = HPIPE_RX_CONTROL_1_RXCLK2X_SEL_MASK;
+	data = 0x1 << HPIPE_RX_CONTROL_1_RXCLK2X_SEL_OFFSET;
+	mask |= HPIPE_RX_CONTROL_1_CLK8T_EN_MASK;
+	data |= 0x1 << HPIPE_RX_CONTROL_1_CLK8T_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_RX_CONTROL_1_REG, data, mask);
+	/* DTL Control */
+	mask = HPIPE_PWR_CTR_DTL_FLOOP_EN_MASK;
+	data = 0x1 << HPIPE_PWR_CTR_DTL_FLOOP_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_DTL_REG, data, mask);
+
+	/* Transmitter/Receiver Speed Divider Force */
+	if (speed == COMPHY_SPEED_5_15625G) {
+		mask = HPIPE_SPD_DIV_FORCE_RX_SPD_DIV_MASK;
+		data = 1 << HPIPE_SPD_DIV_FORCE_RX_SPD_DIV_OFFSET;
+		mask |= HPIPE_SPD_DIV_FORCE_RX_SPD_DIV_FORCE_MASK;
+		data |= 1 << HPIPE_SPD_DIV_FORCE_RX_SPD_DIV_FORCE_OFFSET;
+		mask |= HPIPE_SPD_DIV_FORCE_TX_SPD_DIV_MASK;
+		data |= 1 << HPIPE_SPD_DIV_FORCE_TX_SPD_DIV_OFFSET;
+		mask |= HPIPE_SPD_DIV_FORCE_TX_SPD_DIV_FORCE_MASK;
+		data |= 1 << HPIPE_SPD_DIV_FORCE_TX_SPD_DIV_FORCE_OFFSET;
+	} else {
+		mask = HPIPE_TXDIGCK_DIV_FORCE_MASK;
+		data = 0x1 << HPIPE_TXDIGCK_DIV_FORCE_OFFSET;
+	}
+	reg_set(hpipe_addr + HPIPE_SPD_DIV_FORCE_REG, data, mask);
+
+	/* Set analog parameters from ETP(HW) */
+	debug("stage: Analog parameters from ETP(HW)\n");
+	/* SERDES External Configuration 2 */
+	mask = SD_EXTERNAL_CONFIG2_PIN_DFE_EN_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG2_PIN_DFE_EN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG2_REG, data, mask);
+	/* 0x7-DFE Resolution control */
+	mask = HPIPE_DFE_RES_FORCE_MASK;
+	data = 0x1 << HPIPE_DFE_RES_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_REG0, data, mask);
+	/* 0xd-G1_Setting_0 */
+	if (speed == COMPHY_SPEED_5_15625G) {
+		mask = HPIPE_G1_SET_0_G1_TX_EMPH1_MASK;
+		data = 0x6 << HPIPE_G1_SET_0_G1_TX_EMPH1_OFFSET;
+	} else {
+		mask = HPIPE_G1_SET_0_G1_TX_AMP_MASK;
+		data = xfi_static_values->g1_amp <<
+				HPIPE_G1_SET_0_G1_TX_AMP_OFFSET;
+		mask |= HPIPE_G1_SET_0_G1_TX_EMPH1_MASK;
+		data |= xfi_static_values->g1_emph <<
+				HPIPE_G1_SET_0_G1_TX_EMPH1_OFFSET;
+
+		mask |= HPIPE_G1_SET_0_G1_TX_EMPH1_EN_MASK;
+		data |= xfi_static_values->g1_emph_en <<
+				HPIPE_G1_SET_0_G1_TX_EMPH1_EN_OFFSET;
+		mask |= HPIPE_G1_SET_0_G1_TX_AMP_ADJ_MASK;
+		data |= xfi_static_values->g1_tx_amp_adj <<
+				HPIPE_G1_SET_0_G1_TX_AMP_ADJ_OFFSET;
+	}
+	reg_set(hpipe_addr + HPIPE_G1_SET_0_REG, data, mask);
+	/* Genration 1 setting 2 (G1_Setting_2) */
+	mask = HPIPE_G1_SET_2_G1_TX_EMPH0_MASK;
+	data = xfi_static_values->g1_tx_emph <<
+				HPIPE_G1_SET_2_G1_TX_EMPH0_OFFSET;
+	mask |= HPIPE_G1_SET_2_G1_TX_EMPH0_EN_MASK;
+	data |= xfi_static_values->g1_tx_emph_en <<
+				HPIPE_G1_SET_2_G1_TX_EMPH0_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SET_2_REG, data, mask);
+	/* Transmitter Slew Rate Control register (tx_reg1) */
+	mask = HPIPE_TX_REG1_TX_EMPH_RES_MASK;
+	data = 0x3 << HPIPE_TX_REG1_TX_EMPH_RES_OFFSET;
+	mask |= HPIPE_TX_REG1_SLC_EN_MASK;
+	data |= 0x3f << HPIPE_TX_REG1_SLC_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_REG1_REG, data, mask);
+	/* Impedance Calibration Control register (cal_reg1) */
+	mask = HPIPE_CAL_REG_1_EXT_TXIMP_MASK;
+	data = 0xe << HPIPE_CAL_REG_1_EXT_TXIMP_OFFSET;
+	mask |= HPIPE_CAL_REG_1_EXT_TXIMP_EN_MASK;
+	data |= 0x1 << HPIPE_CAL_REG_1_EXT_TXIMP_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_CAL_REG1_REG, data, mask);
+	/* Generation 1 Setting 5 (g1_setting_5) */
+	mask = HPIPE_G1_SETTING_5_G1_ICP_MASK;
+	data = 0 << HPIPE_CAL_REG_1_EXT_TXIMP_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTING_5_REG, data, mask);
+
+	/* 0xE-G1_Setting_1 */
+	mask = HPIPE_G1_SET_1_G1_RX_DFE_EN_MASK;
+	data = 0x1 << HPIPE_G1_SET_1_G1_RX_DFE_EN_OFFSET;
+	if (speed == COMPHY_SPEED_5_15625G) {
+		mask |= HPIPE_G1_SET_1_G1_RX_SELMUPI_MASK;
+		data |= 0x1 << HPIPE_G1_SET_1_G1_RX_SELMUPI_OFFSET;
+		mask |= HPIPE_G1_SET_1_G1_RX_SELMUPF_MASK;
+		data |= 0x1 << HPIPE_G1_SET_1_G1_RX_SELMUPF_OFFSET;
+	} else {
+		mask |= HPIPE_G1_SET_1_G1_RX_SELMUPI_MASK;
+		data |= xfi_static_values->g1_rx_selmupi <<
+				HPIPE_G1_SET_1_G1_RX_SELMUPI_OFFSET;
+		mask |= HPIPE_G1_SET_1_G1_RX_SELMUPF_MASK;
+		data |= xfi_static_values->g1_rx_selmupf <<
+				HPIPE_G1_SET_1_G1_RX_SELMUPF_OFFSET;
+		mask |= HPIPE_G1_SET_1_G1_RX_SELMUFI_MASK;
+		data |= xfi_static_values->g1_rx_selmufi <<
+				HPIPE_G1_SET_1_G1_RX_SELMUFI_OFFSET;
+		mask |= HPIPE_G1_SET_1_G1_RX_SELMUFF_MASK;
+		data |= xfi_static_values->g1_rx_selmuff <<
+				HPIPE_G1_SET_1_G1_RX_SELMUFF_OFFSET;
+		mask |= HPIPE_G1_SET_1_G1_RX_DIGCK_DIV_MASK;
+		data |= 0x3 << HPIPE_G1_SET_1_G1_RX_DIGCK_DIV_OFFSET;
+	}
+	reg_set(hpipe_addr + HPIPE_G1_SET_1_REG, data, mask);
+
+	/* 0xA-DFE_Reg3 */
+	mask = HPIPE_DFE_F3_F5_DFE_EN_MASK;
+	data = 0x0 << HPIPE_DFE_F3_F5_DFE_EN_OFFSET;
+	mask |= HPIPE_DFE_F3_F5_DFE_CTRL_MASK;
+	data |= 0x0 << HPIPE_DFE_F3_F5_DFE_CTRL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_F3_F5_REG, data, mask);
+
+	/* 0x111-G1_Setting_4 */
+	mask = HPIPE_G1_SETTINGS_4_G1_DFE_RES_MASK;
+	data = 0x1 << HPIPE_G1_SETTINGS_4_G1_DFE_RES_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_4_REG, data, mask);
+	/* Genration 1 setting 3 (G1_Setting_3) */
+	mask = HPIPE_G1_SETTINGS_3_G1_FBCK_SEL_MASK;
+	data = 0x1 << HPIPE_G1_SETTINGS_3_G1_FBCK_SEL_OFFSET;
+	if (speed == COMPHY_SPEED_5_15625G) {
+		/* Force FFE (Feed Forward Equalization) to 5G */
+		mask |= HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_MASK;
+		data |= 0xf << HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_OFFSET;
+		mask |= HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_MASK;
+		data |= 0x4 << HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_OFFSET;
+		mask |= HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_MASK;
+		data |= 0x1 << HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_OFFSET;
+		reg_set(hpipe_addr + HPIPE_G1_SETTINGS_3_REG, data, mask);
+	} else {
+		mask |= HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_MASK;
+		data |= xfi_static_values->g1_ffe_cap_sel <<
+			HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_OFFSET;
+		mask |= HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_MASK;
+		data |= xfi_static_values->g1_ffe_res_sel <<
+			HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_OFFSET;
+		mask |= HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_MASK;
+		data |= 0x1 << HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_OFFSET;
+		reg_set(hpipe_addr + HPIPE_G1_SETTINGS_3_REG, data, mask);
+
+		/* Use the value from CAL_OS_PH_EXT */
+		mask = HPIPE_CAL_RXCLKALIGN_90_EXT_EN_MASK;
+		data = 1 << HPIPE_CAL_RXCLKALIGN_90_EXT_EN_OFFSET;
+		reg_set(hpipe_addr +
+			HPIPE_RX_CLK_ALIGN90_AND_TX_IDLE_CALIB_CTRL_REG,
+			data, mask);
+
+		/* Update align90 */
+		mask = HPIPE_CAL_OS_PH_EXT_MASK;
+		data = xfi_static_values->align90 << HPIPE_CAL_OS_PH_EXT_OFFSET;
+		reg_set(hpipe_addr +
+			HPIPE_RX_CLK_ALIGN90_AND_TX_IDLE_CALIB_CTRL_REG,
+			data, mask);
+
+		/* Force DFE resolution (use gen table value) */
+		mask = HPIPE_DFE_RES_FORCE_MASK;
+		data = 0x0 << HPIPE_DFE_RES_FORCE_OFFSET;
+		reg_set(hpipe_addr + HPIPE_DFE_REG0, data, mask);
+
+		/* 0x111-G1 DFE_Setting_4 */
+		mask = HPIPE_G1_SETTINGS_4_G1_DFE_RES_MASK;
+		data = xfi_static_values->g1_dfe_res <<
+			HPIPE_G1_SETTINGS_4_G1_DFE_RES_OFFSET;
+		reg_set(hpipe_addr + HPIPE_G1_SETTINGS_4_REG, data, mask);
+	}
+
+	/* Connfigure RX training timer */
+	mask = HPIPE_RX_TRAIN_TIMER_MASK;
+	data = 0x13 << HPIPE_RX_TRAIN_TIMER_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_5_REG, data, mask);
+
+	/* Enable TX train peak to peak hold */
+	mask = HPIPE_TX_TRAIN_P2P_HOLD_MASK;
+	data = 0x1 << HPIPE_TX_TRAIN_P2P_HOLD_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_0_REG, data, mask);
+
+	/* Configure TX preset index */
+	mask = HPIPE_TX_PRESET_INDEX_MASK;
+	data = 0x2 << HPIPE_TX_PRESET_INDEX_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_PRESET_INDEX_REG, data, mask);
+
+	/* Disable pattern lock lost timeout */
+	mask = HPIPE_PATTERN_LOCK_LOST_TIMEOUT_EN_MASK;
+	data = 0x0 << HPIPE_PATTERN_LOCK_LOST_TIMEOUT_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_FRAME_DETECT_CTRL_3_REG, data, mask);
+
+	/* Configure TX training pattern and TX training 16bit auto */
+	mask = HPIPE_TX_TRAIN_16BIT_AUTO_EN_MASK;
+	data = 0x1 << HPIPE_TX_TRAIN_16BIT_AUTO_EN_OFFSET;
+	mask |= HPIPE_TX_TRAIN_PAT_SEL_MASK;
+	data |= 0x1 << HPIPE_TX_TRAIN_PAT_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_REG, data, mask);
+
+	/* Configure Training patten number */
+	mask = HPIPE_TRAIN_PAT_NUM_MASK;
+	data = 0x88 << HPIPE_TRAIN_PAT_NUM_OFFSET;
+	reg_set(hpipe_addr + HPIPE_FRAME_DETECT_CTRL_0_REG, data, mask);
+
+	/* Configure differencial manchester encoter to ethernet mode */
+	mask = HPIPE_DME_ETHERNET_MODE_MASK;
+	data = 0x1 << HPIPE_DME_ETHERNET_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DME_REG, data, mask);
+
+	/* Configure VDD Continuous Calibration */
+	mask = HPIPE_CAL_VDD_CONT_MODE_MASK;
+	data = 0x1 << HPIPE_CAL_VDD_CONT_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_VDD_CAL_0_REG, data, mask);
+
+	/* Trigger sampler enable pulse (by toggleing the bit) */
+	mask = HPIPE_RX_SAMPLER_OS_GAIN_MASK;
+	data = 0x3 << HPIPE_RX_SAMPLER_OS_GAIN_OFFSET;
+	mask |= HPIPE_SMAPLER_MASK;
+	data |= 0x1 << HPIPE_SMAPLER_OFFSET;
+	reg_set(hpipe_addr + HPIPE_SAMPLER_N_PROC_CALIB_CTRL_REG, data, mask);
+	mask = HPIPE_SMAPLER_MASK;
+	data = 0x0 << HPIPE_SMAPLER_OFFSET;
+	reg_set(hpipe_addr + HPIPE_SAMPLER_N_PROC_CALIB_CTRL_REG, data, mask);
+
+	/* Set External RX Regulator Control */
+	mask = HPIPE_EXT_SELLV_RXSAMPL_MASK;
+	data = 0x1A << HPIPE_EXT_SELLV_RXSAMPL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_VDD_CAL_CTRL_REG, data, mask);
+
+	debug("stage: RFU configurations- Power Up PLL,Tx,Rx\n");
+	/* SERDES External Configuration */
+	mask = SD_EXTERNAL_CONFIG0_SD_PU_PLL_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_PLL_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_RX_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_TX_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_TX_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG0_REG, data, mask);
+
+	/* check PLL rx & tx ready */
+	addr = sd_ip_addr + SD_EXTERNAL_STATUS0_REG;
+	data = SD_EXTERNAL_STATUS0_PLL_RX_MASK |
+	       SD_EXTERNAL_STATUS0_PLL_TX_MASK;
+	mask = data;
+	data = polling_with_timeout(addr, data, mask,
+				    PLL_LOCK_TIMEOUT, REG_32BIT);
+	if (data != 0) {
+		if (data & SD_EXTERNAL_STATUS0_PLL_RX_MASK)
+			ERROR("RX PLL is not locked\n");
+		if (data & SD_EXTERNAL_STATUS0_PLL_TX_MASK)
+			ERROR("TX PLL is not locked\n");
+
+		ret = -ETIMEDOUT;
+	}
+
+	/* RX init */
+	mask = SD_EXTERNAL_CONFIG1_RX_INIT_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG1_RX_INIT_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* check that RX init done */
+	addr = sd_ip_addr + SD_EXTERNAL_STATUS0_REG;
+	data = SD_EXTERNAL_STATUS0_RX_INIT_MASK;
+	mask = data;
+	data = polling_with_timeout(addr, data, mask, 100, REG_32BIT);
+	if (data != 0) {
+		ERROR("RX init failed\n");
+		ret = -ETIMEDOUT;
+	}
+
+	debug("stage: RF Reset\n");
+	/* RF Reset */
+	mask =  SD_EXTERNAL_CONFIG1_RX_INIT_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG1_RX_INIT_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* Force rx training on 10G port */
+	data = mmio_read_32(COMPHY_TRX_RELATIVE_ADDR(comphy_index));
+	data |= COMPHY_TRX_TRAIN_RX_TRAIN_ENABLE;
+	mmio_write_32(COMPHY_TRX_RELATIVE_ADDR(comphy_index), data);
+	mdelay(200);
+	data &= ~COMPHY_TRX_TRAIN_RX_TRAIN_ENABLE;
+	mmio_write_32(COMPHY_TRX_RELATIVE_ADDR(comphy_index), data);
+
+	debug_exit();
+
+	return ret;
+}
+
+static int mvebu_cp110_comphy_pcie_power_on(uint64_t comphy_base,
+				     uint8_t comphy_index, uint32_t comphy_mode)
+{
+	int ret = 0;
+	uint32_t reg, mask, data, pcie_width;
+	uint32_t clk_dir;
+	uintptr_t hpipe_addr, comphy_addr, addr;
+	_Bool clk_src = COMPHY_GET_CLK_SRC(comphy_mode);
+	_Bool called_from_uboot = COMPHY_GET_CALLER(comphy_mode);
+
+	/* In Armada 8K DB boards, PCIe initialization can be executed
+	 * only once (PCIe reset performed during chip power on and
+	 * it cannot be executed via GPIO later).
+	 * This means that power on can be executed only once, so let's
+	 * mark if the caller is bootloader or Linux.
+	 * If bootloader -> run power on.
+	 * If Linux -> exit.
+	 *
+	 * TODO: In MacciatoBIN, PCIe reset is connected via GPIO,
+	 * so after GPIO reset is added to Linux Kernel, it can be
+	 * powered-on by Linux.
+	 */
+	if (!called_from_uboot)
+		return ret;
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+	comphy_addr = COMPHY_ADDR(comphy_base, comphy_index);
+	pcie_width = COMPHY_GET_PCIE_WIDTH(comphy_mode);
+
+	debug_enter();
+
+	spin_lock(&cp110_mac_reset_lock);
+
+	reg = mmio_read_32(SYS_CTRL_FROM_COMPHY_ADDR(comphy_base) +
+						SYS_CTRL_UINIT_SOFT_RESET_REG);
+	switch (comphy_index) {
+	case COMPHY_LANE0:
+		reg |= PCIE_MAC_RESET_MASK_PORT0;
+		break;
+	case COMPHY_LANE4:
+		reg |= PCIE_MAC_RESET_MASK_PORT1;
+		break;
+	case COMPHY_LANE5:
+		reg |= PCIE_MAC_RESET_MASK_PORT2;
+		break;
+	}
+
+	mmio_write_32(SYS_CTRL_FROM_COMPHY_ADDR(comphy_base) +
+					    SYS_CTRL_UINIT_SOFT_RESET_REG, reg);
+	spin_unlock(&cp110_mac_reset_lock);
+
+	/* Configure PIPE selector for PCIE */
+	mvebu_cp110_comphy_set_pipe_selector(comphy_base, comphy_index,
+					     comphy_mode);
+
+	/*
+	 * Read SAR (Sample-At-Reset) configuration for the PCIe clock
+	 * direction.
+	 *
+	 * SerDes Lane 4/5 got the PCIe ref-clock #1,
+	 * and SerDes Lane 0 got PCIe ref-clock #0
+	 */
+	reg = mmio_read_32(DFX_FROM_COMPHY_ADDR(comphy_base) +
+			   SAR_STATUS_0_REG);
+	if (comphy_index == COMPHY_LANE4 || comphy_index == COMPHY_LANE5)
+		clk_dir = (reg & SAR_RST_PCIE1_CLOCK_CONFIG_CP0_MASK) >>
+					  SAR_RST_PCIE1_CLOCK_CONFIG_CP0_OFFSET;
+	else
+		clk_dir = (reg & SAR_RST_PCIE0_CLOCK_CONFIG_CP0_MASK) >>
+					  SAR_RST_PCIE0_CLOCK_CONFIG_CP0_OFFSET;
+
+	debug("On lane %d\n", comphy_index);
+	debug("PCIe clock direction = %x\n", clk_dir);
+	debug("PCIe Width = %d\n", pcie_width);
+
+	/* enable PCIe X4 and X2 */
+	if (comphy_index == COMPHY_LANE0) {
+		if (pcie_width == PCIE_LNK_X4) {
+			data = 0x1 << COMMON_PHY_SD_CTRL1_PCIE_X4_EN_OFFSET;
+			mask = COMMON_PHY_SD_CTRL1_PCIE_X4_EN_MASK;
+			reg_set(comphy_base + COMMON_PHY_SD_CTRL1,
+				data, mask);
+		} else if (pcie_width == PCIE_LNK_X2) {
+			data = 0x1 << COMMON_PHY_SD_CTRL1_PCIE_X2_EN_OFFSET;
+			mask = COMMON_PHY_SD_CTRL1_PCIE_X2_EN_MASK;
+			reg_set(comphy_base + COMMON_PHY_SD_CTRL1, data, mask);
+		}
+	}
+
+	/* If PCIe clock is output and clock source from SerDes lane 5,
+	 * need to configure the clock-source MUX.
+	 * By default, the clock source is from lane 4
+	 */
+	if (clk_dir && clk_src && (comphy_index == COMPHY_LANE5)) {
+		data = DFX_DEV_GEN_PCIE_CLK_SRC_MUX <<
+						DFX_DEV_GEN_PCIE_CLK_SRC_OFFSET;
+		mask = DFX_DEV_GEN_PCIE_CLK_SRC_MASK;
+		reg_set(DFX_FROM_COMPHY_ADDR(comphy_base) +
+			DFX_DEV_GEN_CTRL12_REG, data, mask);
+	}
+
+	debug("stage: RFU configurations - hard reset comphy\n");
+	/* RFU configurations - hard reset comphy */
+	mask = COMMON_PHY_CFG1_PWR_UP_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_UP_OFFSET;
+	mask |= COMMON_PHY_CFG1_PIPE_SELECT_MASK;
+	data |= 0x1 << COMMON_PHY_CFG1_PIPE_SELECT_OFFSET;
+	mask |= COMMON_PHY_CFG1_PWR_ON_RESET_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PWR_ON_RESET_OFFSET;
+	mask |= COMMON_PHY_CFG1_CORE_RSTN_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_CORE_RSTN_OFFSET;
+	mask |= COMMON_PHY_PHY_MODE_MASK;
+	data |= 0x0 << COMMON_PHY_PHY_MODE_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* release from hard reset */
+	mask = COMMON_PHY_CFG1_PWR_ON_RESET_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_ON_RESET_OFFSET;
+	mask |= COMMON_PHY_CFG1_CORE_RSTN_MASK;
+	data |= 0x1 << COMMON_PHY_CFG1_CORE_RSTN_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* Wait 1ms - until band gap and ref clock ready */
+	mdelay(1);
+	/* Start comphy Configuration */
+	debug("stage: Comphy configuration\n");
+	/* Set PIPE soft reset */
+	mask = HPIPE_RST_CLK_CTRL_PIPE_RST_MASK;
+	data = 0x1 << HPIPE_RST_CLK_CTRL_PIPE_RST_OFFSET;
+	/* Set PHY datapath width mode for V0 */
+	mask |= HPIPE_RST_CLK_CTRL_FIXED_PCLK_MASK;
+	data |= 0x1 << HPIPE_RST_CLK_CTRL_FIXED_PCLK_OFFSET;
+	/* Set Data bus width USB mode for V0 */
+	mask |= HPIPE_RST_CLK_CTRL_PIPE_WIDTH_MASK;
+	data |= 0x0 << HPIPE_RST_CLK_CTRL_PIPE_WIDTH_OFFSET;
+	/* Set CORE_CLK output frequency for 250Mhz */
+	mask |= HPIPE_RST_CLK_CTRL_CORE_FREQ_SEL_MASK;
+	data |= 0x0 << HPIPE_RST_CLK_CTRL_CORE_FREQ_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_RST_CLK_CTRL_REG, data, mask);
+	/* Set PLL ready delay for 0x2 */
+	data = 0x2 << HPIPE_CLK_SRC_LO_PLL_RDY_DL_OFFSET;
+	mask = HPIPE_CLK_SRC_LO_PLL_RDY_DL_MASK;
+	if (pcie_width != PCIE_LNK_X1) {
+		data |= 0x1 << HPIPE_CLK_SRC_LO_BUNDLE_PERIOD_SEL_OFFSET;
+		mask |= HPIPE_CLK_SRC_LO_BUNDLE_PERIOD_SEL_MASK;
+		data |= 0x1 << HPIPE_CLK_SRC_LO_BUNDLE_PERIOD_SCALE_OFFSET;
+		mask |= HPIPE_CLK_SRC_LO_BUNDLE_PERIOD_SCALE_MASK;
+	}
+	reg_set(hpipe_addr + HPIPE_CLK_SRC_LO_REG, data, mask);
+
+	/* Set PIPE mode interface to PCIe3 - 0x1  & set lane order */
+	data = 0x1 << HPIPE_CLK_SRC_HI_MODE_PIPE_OFFSET;
+	mask = HPIPE_CLK_SRC_HI_MODE_PIPE_MASK;
+	if (pcie_width != PCIE_LNK_X1) {
+		mask |= HPIPE_CLK_SRC_HI_LANE_STRT_MASK;
+		mask |= HPIPE_CLK_SRC_HI_LANE_MASTER_MASK;
+		mask |= HPIPE_CLK_SRC_HI_LANE_BREAK_MASK;
+		if (comphy_index == 0) {
+			data |= 0x1 << HPIPE_CLK_SRC_HI_LANE_STRT_OFFSET;
+			data |= 0x1 << HPIPE_CLK_SRC_HI_LANE_MASTER_OFFSET;
+		} else if (comphy_index == (pcie_width - 1)) {
+			data |= 0x1 << HPIPE_CLK_SRC_HI_LANE_BREAK_OFFSET;
+		}
+	}
+	reg_set(hpipe_addr + HPIPE_CLK_SRC_HI_REG, data, mask);
+	/* Config update polarity equalization */
+	data = 0x1 << HPIPE_CFG_UPDATE_POLARITY_OFFSET;
+	mask = HPIPE_CFG_UPDATE_POLARITY_MASK;
+	reg_set(hpipe_addr + HPIPE_LANE_EQ_CFG1_REG, data, mask);
+	/* Set PIPE version 4 to mode enable */
+	data = 0x1 << HPIPE_DFE_CTRL_28_PIPE4_OFFSET;
+	mask = HPIPE_DFE_CTRL_28_PIPE4_MASK;
+	reg_set(hpipe_addr + HPIPE_DFE_CTRL_28_REG, data, mask);
+	/* TODO: check if pcie clock is output/input - for bringup use input*/
+	/* Enable PIN clock 100M_125M */
+	mask = 0;
+	data = 0;
+	/* Only if clock is output, configure the clock-source mux */
+	if (clk_dir) {
+		mask |= HPIPE_MISC_CLK100M_125M_MASK;
+		data |= 0x1 << HPIPE_MISC_CLK100M_125M_OFFSET;
+	}
+	/* Set PIN_TXDCLK_2X Clock Freq. Selection for outputs 500MHz clock */
+	mask |= HPIPE_MISC_TXDCLK_2X_MASK;
+	data |= 0x0 << HPIPE_MISC_TXDCLK_2X_OFFSET;
+	/* Enable 500MHz Clock */
+	mask |= HPIPE_MISC_CLK500_EN_MASK;
+	data |= 0x1 << HPIPE_MISC_CLK500_EN_OFFSET;
+	if (clk_dir) { /* output */
+		/* Set reference clock comes from group 1 */
+		mask |= HPIPE_MISC_REFCLK_SEL_MASK;
+		data |= 0x0 << HPIPE_MISC_REFCLK_SEL_OFFSET;
+	} else {
+		/* Set reference clock comes from group 2 */
+		mask |= HPIPE_MISC_REFCLK_SEL_MASK;
+		data |= 0x1 << HPIPE_MISC_REFCLK_SEL_OFFSET;
+	}
+	mask |= HPIPE_MISC_ICP_FORCE_MASK;
+	data |= 0x1 << HPIPE_MISC_ICP_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_MISC_REG, data, mask);
+	if (clk_dir) { /* output */
+		/* Set reference frequcency select - 0x2 for 25MHz*/
+		mask = HPIPE_PWR_PLL_REF_FREQ_MASK;
+		data = 0x2 << HPIPE_PWR_PLL_REF_FREQ_OFFSET;
+	} else {
+		/* Set reference frequcency select - 0x0 for 100MHz*/
+		mask = HPIPE_PWR_PLL_REF_FREQ_MASK;
+		data = 0x0 << HPIPE_PWR_PLL_REF_FREQ_OFFSET;
+	}
+	/* Set PHY mode to PCIe */
+	mask |= HPIPE_PWR_PLL_PHY_MODE_MASK;
+	data |= 0x3 << HPIPE_PWR_PLL_PHY_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_PLL_REG, data, mask);
+
+	/* ref clock alignment */
+	if (pcie_width != PCIE_LNK_X1) {
+		mask = HPIPE_LANE_ALIGN_OFF_MASK;
+		data = 0x0 << HPIPE_LANE_ALIGN_OFF_OFFSET;
+		reg_set(hpipe_addr + HPIPE_LANE_ALIGN_REG, data, mask);
+	}
+
+	/* Set the amount of time spent in the LoZ state - set for 0x7 only if
+	 * the PCIe clock is output
+	 */
+	if (clk_dir)
+		reg_set(hpipe_addr + HPIPE_GLOBAL_PM_CTRL,
+			0x7 << HPIPE_GLOBAL_PM_RXDLOZ_WAIT_OFFSET,
+			HPIPE_GLOBAL_PM_RXDLOZ_WAIT_MASK);
+
+	/* Set Maximal PHY Generation Setting(8Gbps) */
+	mask = HPIPE_INTERFACE_GEN_MAX_MASK;
+	data = 0x2 << HPIPE_INTERFACE_GEN_MAX_OFFSET;
+	/* Bypass frame detection and sync detection for RX DATA */
+	mask |= HPIPE_INTERFACE_DET_BYPASS_MASK;
+	data |= 0x1 << HPIPE_INTERFACE_DET_BYPASS_OFFSET;
+	/* Set Link Train Mode (Tx training control pins are used) */
+	mask |= HPIPE_INTERFACE_LINK_TRAIN_MASK;
+	data |= 0x1 << HPIPE_INTERFACE_LINK_TRAIN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_INTERFACE_REG, data, mask);
+
+	/* Set Idle_sync enable */
+	mask = HPIPE_PCIE_IDLE_SYNC_MASK;
+	data = 0x1 << HPIPE_PCIE_IDLE_SYNC_OFFSET;
+	/* Select bits for PCIE Gen3(32bit) */
+	mask |= HPIPE_PCIE_SEL_BITS_MASK;
+	data |= 0x2 << HPIPE_PCIE_SEL_BITS_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PCIE_REG0, data, mask);
+
+	/* Enable Tx_adapt_g1 */
+	mask = HPIPE_TX_TRAIN_CTRL_G1_MASK;
+	data = 0x1 << HPIPE_TX_TRAIN_CTRL_G1_OFFSET;
+	/* Enable Tx_adapt_gn1 */
+	mask |= HPIPE_TX_TRAIN_CTRL_GN1_MASK;
+	data |= 0x1 << HPIPE_TX_TRAIN_CTRL_GN1_OFFSET;
+	/* Disable Tx_adapt_g0 */
+	mask |= HPIPE_TX_TRAIN_CTRL_G0_MASK;
+	data |= 0x0 << HPIPE_TX_TRAIN_CTRL_G0_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_REG, data, mask);
+
+	/* Set reg_tx_train_chk_init */
+	mask = HPIPE_TX_TRAIN_CHK_INIT_MASK;
+	data = 0x0 << HPIPE_TX_TRAIN_CHK_INIT_OFFSET;
+	/* Enable TX_COE_FM_PIN_PCIE3_EN */
+	mask |= HPIPE_TX_TRAIN_COE_FM_PIN_PCIE3_MASK;
+	data |= 0x1 << HPIPE_TX_TRAIN_COE_FM_PIN_PCIE3_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_REG, data, mask);
+
+	debug("stage: TRx training parameters\n");
+	/* Set Preset sweep configurations */
+	mask = HPIPE_TX_TX_STATUS_CHECK_MODE_MASK;
+	data = 0x1 << HPIPE_TX_STATUS_CHECK_MODE_OFFSET;
+	mask |= HPIPE_TX_NUM_OF_PRESET_MASK;
+	data |= 0x7 << HPIPE_TX_NUM_OF_PRESET_OFFSET;
+	mask |= HPIPE_TX_SWEEP_PRESET_EN_MASK;
+	data |= 0x1 << HPIPE_TX_SWEEP_PRESET_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_11_REG, data, mask);
+
+	/* Tx train start configuration */
+	mask = HPIPE_TX_TRAIN_START_SQ_EN_MASK;
+	data = 0x1 << HPIPE_TX_TRAIN_START_SQ_EN_OFFSET;
+	mask |= HPIPE_TX_TRAIN_START_FRM_DET_EN_MASK;
+	data |= 0x0 << HPIPE_TX_TRAIN_START_FRM_DET_EN_OFFSET;
+	mask |= HPIPE_TX_TRAIN_START_FRM_LOCK_EN_MASK;
+	data |= 0x0 << HPIPE_TX_TRAIN_START_FRM_LOCK_EN_OFFSET;
+	mask |= HPIPE_TX_TRAIN_WAIT_TIME_EN_MASK;
+	data |= 0x1 << HPIPE_TX_TRAIN_WAIT_TIME_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_5_REG, data, mask);
+
+	/* Enable Tx train P2P */
+	mask = HPIPE_TX_TRAIN_P2P_HOLD_MASK;
+	data = 0x1 << HPIPE_TX_TRAIN_P2P_HOLD_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_0_REG, data, mask);
+
+	/* Configure Tx train timeout */
+	mask = HPIPE_TRX_TRAIN_TIMER_MASK;
+	data = 0x17 << HPIPE_TRX_TRAIN_TIMER_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_4_REG, data, mask);
+
+	/* Disable G0/G1/GN1 adaptation */
+	mask = HPIPE_TX_TRAIN_CTRL_G1_MASK | HPIPE_TX_TRAIN_CTRL_GN1_MASK
+		| HPIPE_TX_TRAIN_CTRL_G0_OFFSET;
+	data = 0;
+	reg_set(hpipe_addr + HPIPE_TX_TRAIN_CTRL_REG, data, mask);
+
+	/* Disable DTL frequency loop */
+	mask = HPIPE_PWR_CTR_DTL_FLOOP_EN_MASK;
+	data = 0x0 << HPIPE_PWR_CTR_DTL_FLOOP_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_DTL_REG, data, mask);
+
+	/* Configure G3 DFE */
+	mask = HPIPE_G3_DFE_RES_MASK;
+	data = 0x3 << HPIPE_G3_DFE_RES_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SETTING_4_REG, data, mask);
+
+	/* Use TX/RX training result for DFE */
+	mask = HPIPE_DFE_RES_FORCE_MASK;
+	data = 0x0 << HPIPE_DFE_RES_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_REG0,  data, mask);
+
+	/* Configure initial and final coefficient value for receiver */
+	mask = HPIPE_G3_SET_1_G3_RX_SELMUPI_MASK;
+	data = 0x1 << HPIPE_G3_SET_1_G3_RX_SELMUPI_OFFSET;
+
+	mask |= HPIPE_G3_SET_1_G3_RX_SELMUPF_MASK;
+	data |= 0x1 << HPIPE_G3_SET_1_G3_RX_SELMUPF_OFFSET;
+
+	mask |= HPIPE_G3_SET_1_G3_SAMPLER_INPAIRX2_EN_MASK;
+	data |= 0x0 << HPIPE_G3_SET_1_G3_SAMPLER_INPAIRX2_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SET_1_REG,  data, mask);
+
+	/* Trigger sampler enable pulse */
+	mask = HPIPE_SMAPLER_MASK;
+	data = 0x1 << HPIPE_SMAPLER_OFFSET;
+	reg_set(hpipe_addr + HPIPE_SAMPLER_N_PROC_CALIB_CTRL_REG, data, mask);
+	udelay(5);
+	reg_set(hpipe_addr + HPIPE_SAMPLER_N_PROC_CALIB_CTRL_REG, 0, mask);
+
+	/* FFE resistor tuning for different bandwidth  */
+	mask = HPIPE_G3_FFE_DEG_RES_LEVEL_MASK;
+	data = 0x1 << HPIPE_G3_FFE_DEG_RES_LEVEL_OFFSET;
+	mask |= HPIPE_G3_FFE_LOAD_RES_LEVEL_MASK;
+	data |= 0x3 << HPIPE_G3_FFE_LOAD_RES_LEVEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SETTING_3_REG, data, mask);
+
+	/* Pattern lock lost timeout disable */
+	mask = HPIPE_PATTERN_LOCK_LOST_TIMEOUT_EN_MASK;
+	data = 0x0 << HPIPE_PATTERN_LOCK_LOST_TIMEOUT_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_FRAME_DETECT_CTRL_3_REG, data, mask);
+
+	/* Configure DFE adaptations */
+	mask = HPIPE_CDR_RX_MAX_DFE_ADAPT_0_MASK;
+	data = 0x0 << HPIPE_CDR_RX_MAX_DFE_ADAPT_0_OFFSET;
+	mask |= HPIPE_CDR_RX_MAX_DFE_ADAPT_1_MASK;
+	data |= 0x0 << HPIPE_CDR_RX_MAX_DFE_ADAPT_1_OFFSET;
+	mask |= HPIPE_CDR_MAX_DFE_ADAPT_0_MASK;
+	data |= 0x0 << HPIPE_CDR_MAX_DFE_ADAPT_0_OFFSET;
+	mask |= HPIPE_CDR_MAX_DFE_ADAPT_1_MASK;
+	data |= 0x1 << HPIPE_CDR_MAX_DFE_ADAPT_1_OFFSET;
+	reg_set(hpipe_addr + HPIPE_CDR_CONTROL_REG, data, mask);
+
+	mask = HPIPE_DFE_TX_MAX_DFE_ADAPT_MASK;
+	data = 0x0 << HPIPE_DFE_TX_MAX_DFE_ADAPT_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_CONTROL_REG, data, mask);
+
+	/* Genration 2 setting 1*/
+	mask = HPIPE_G2_SET_1_G2_RX_SELMUPI_MASK;
+	data = 0x0 << HPIPE_G2_SET_1_G2_RX_SELMUPI_OFFSET;
+	mask |= HPIPE_G2_SET_1_G2_RX_SELMUPF_MASK;
+	data |= 0x1 << HPIPE_G2_SET_1_G2_RX_SELMUPF_OFFSET;
+	mask |= HPIPE_G2_SET_1_G2_RX_SELMUFI_MASK;
+	data |= 0x0 << HPIPE_G2_SET_1_G2_RX_SELMUFI_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G2_SET_1_REG, data, mask);
+
+	/* DFE enable */
+	mask = HPIPE_G2_DFE_RES_MASK;
+	data = 0x3 << HPIPE_G2_DFE_RES_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G2_SETTINGS_4_REG, data, mask);
+
+	/* Configure DFE Resolution */
+	mask = HPIPE_LANE_CFG4_DFE_EN_SEL_MASK;
+	data = 0x1 << HPIPE_LANE_CFG4_DFE_EN_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_LANE_CFG4_REG, data, mask);
+
+	/* VDD calibration control */
+	mask = HPIPE_EXT_SELLV_RXSAMPL_MASK;
+	data = 0x16 << HPIPE_EXT_SELLV_RXSAMPL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_VDD_CAL_CTRL_REG, data, mask);
+
+	/* Set PLL Charge-pump Current Control */
+	mask = HPIPE_G3_SETTING_5_G3_ICP_MASK;
+	data = 0x4 << HPIPE_G3_SETTING_5_G3_ICP_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G3_SETTING_5_REG, data, mask);
+
+	/* Set lane rqualization remote setting */
+	mask = HPIPE_LANE_CFG_FOM_DIRN_OVERRIDE_MASK;
+	data = 0x1 << HPIPE_LANE_CFG_FOM_DIRN_OVERRIDE_OFFSET;
+	mask |= HPIPE_LANE_CFG_FOM_ONLY_MODE_MASK;
+	data |= 0x1 << HPIPE_LANE_CFG_FOM_ONLY_MODE_OFFFSET;
+	mask |= HPIPE_LANE_CFG_FOM_PRESET_VECTOR_MASK;
+	data |= 0x6 << HPIPE_LANE_CFG_FOM_PRESET_VECTOR_OFFSET;
+	reg_set(hpipe_addr + HPIPE_LANE_EQ_REMOTE_SETTING_REG, data, mask);
+
+	mask = HPIPE_CFG_EQ_BUNDLE_DIS_MASK;
+	data = 0x1 << HPIPE_CFG_EQ_BUNDLE_DIS_OFFSET;
+	reg_set(hpipe_addr + HPIPE_LANE_EQ_CFG2_REG, data, mask);
+
+	debug("stage: Comphy power up\n");
+
+	/* For PCIe X4 or X2:
+	 * release from reset only after finish to configure all lanes
+	 */
+	if ((pcie_width == PCIE_LNK_X1) || (comphy_index == (pcie_width - 1))) {
+		uint32_t i, start_lane, end_lane;
+
+		if (pcie_width != PCIE_LNK_X1) {
+			/* allows writing to all lanes in one write */
+			data = 0x0;
+			if (pcie_width == PCIE_LNK_X2)
+				mask = COMMON_PHY_SD_CTRL1_COMPHY_0_1_PORT_MASK;
+			else if (pcie_width == PCIE_LNK_X4)
+				mask = COMMON_PHY_SD_CTRL1_COMPHY_0_3_PORT_MASK;
+			reg_set(comphy_base + COMMON_PHY_SD_CTRL1, data, mask);
+			start_lane = 0;
+			end_lane = pcie_width;
+
+			/* Release from PIPE soft reset
+			 * For PCIe by4 or by2:
+			 * release from soft reset all lanes - can't use
+			 * read modify write
+			 */
+			reg_set(HPIPE_ADDR(
+				COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base), 0) +
+				HPIPE_RST_CLK_CTRL_REG, 0x24, 0xffffffff);
+		} else {
+			start_lane = comphy_index;
+			end_lane = comphy_index + 1;
+
+			/* Release from PIPE soft reset
+			 * for PCIe by4 or by2:
+			 * release from soft reset all lanes
+			 */
+			reg_set(hpipe_addr + HPIPE_RST_CLK_CTRL_REG,
+				0x0 << HPIPE_RST_CLK_CTRL_PIPE_RST_OFFSET,
+				HPIPE_RST_CLK_CTRL_PIPE_RST_MASK);
+		}
+
+		if (pcie_width != PCIE_LNK_X1) {
+			/* disable writing to all lanes with one write */
+			if (pcie_width == PCIE_LNK_X2) {
+				data = (COMPHY_LANE0 <<
+				COMMON_PHY_SD_CTRL1_COMPHY_0_PORT_OFFSET) |
+				(COMPHY_LANE1 <<
+				COMMON_PHY_SD_CTRL1_COMPHY_1_PORT_OFFSET);
+				mask = COMMON_PHY_SD_CTRL1_COMPHY_0_1_PORT_MASK;
+			} else if (pcie_width == PCIE_LNK_X4) {
+				data = (COMPHY_LANE0 <<
+				COMMON_PHY_SD_CTRL1_COMPHY_0_PORT_OFFSET) |
+				(COMPHY_LANE1 <<
+				COMMON_PHY_SD_CTRL1_COMPHY_1_PORT_OFFSET) |
+				(COMPHY_LANE2 <<
+				COMMON_PHY_SD_CTRL1_COMPHY_2_PORT_OFFSET) |
+				(COMPHY_LANE3 <<
+				COMMON_PHY_SD_CTRL1_COMPHY_3_PORT_OFFSET);
+				mask = COMMON_PHY_SD_CTRL1_COMPHY_0_3_PORT_MASK;
+			}
+			reg_set(comphy_base + COMMON_PHY_SD_CTRL1,
+				data, mask);
+		}
+
+		debug("stage: Check PLL\n");
+		/* Read lane status */
+		for (i = start_lane; i < end_lane; i++) {
+			addr = HPIPE_ADDR(
+				COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base), i) +
+				HPIPE_LANE_STATUS1_REG;
+			data = HPIPE_LANE_STATUS1_PCLK_EN_MASK;
+			mask = data;
+			data = polling_with_timeout(addr, data, mask,
+						   PLL_LOCK_TIMEOUT,
+						   REG_32BIT);
+			if (data) {
+				ERROR("Failed to lock PCIE PLL\n");
+				ret = -ETIMEDOUT;
+			}
+		}
+	}
+
+	debug_exit();
+
+	return ret;
+}
+
+static int mvebu_cp110_comphy_rxaui_power_on(uint64_t comphy_base,
+				     uint8_t comphy_index, uint32_t comphy_mode)
+{
+	uintptr_t hpipe_addr, sd_ip_addr, comphy_addr, addr;
+	uint32_t mask, data;
+	int ret = 0;
+
+	debug_enter();
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+	comphy_addr = COMPHY_ADDR(comphy_base, comphy_index);
+	sd_ip_addr = SD_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+			     comphy_index);
+
+	/* configure phy selector for RXAUI */
+	mvebu_cp110_comphy_set_phy_selector(comphy_base, comphy_index,
+					    comphy_mode);
+
+	/* RFU configurations - hard reset comphy */
+	mask = COMMON_PHY_CFG1_PWR_UP_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_UP_OFFSET;
+	mask |= COMMON_PHY_CFG1_PIPE_SELECT_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PIPE_SELECT_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	if (comphy_index == 2) {
+		reg_set(comphy_base + COMMON_PHY_SD_CTRL1,
+			0x1 << COMMON_PHY_SD_CTRL1_RXAUI0_OFFSET,
+			COMMON_PHY_SD_CTRL1_RXAUI0_MASK);
+	}
+	if (comphy_index == 4) {
+		reg_set(comphy_base + COMMON_PHY_SD_CTRL1,
+			0x1 << COMMON_PHY_SD_CTRL1_RXAUI1_OFFSET,
+			COMMON_PHY_SD_CTRL1_RXAUI1_MASK);
+	}
+
+	/* Select Baud Rate of Comphy And PD_PLL/Tx/Rx */
+	mask = SD_EXTERNAL_CONFIG0_SD_PU_PLL_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG0_SD_PU_PLL_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PHY_GEN_RX_MASK;
+	data |= 0xB << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PHY_GEN_TX_MASK;
+	data |= 0xB << SD_EXTERNAL_CONFIG0_SD_PHY_GEN_TX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_RX_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG0_SD_PU_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_TX_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG0_SD_PU_TX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_HALF_BUS_MODE_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG0_HALF_BUS_MODE_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_MEDIA_MODE_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG0_MEDIA_MODE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG0_REG, data, mask);
+
+	/* release from hard reset */
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* Wait 1ms - until band gap and ref clock ready */
+	mdelay(1);
+
+	/* Start comphy Configuration */
+	debug("stage: Comphy configuration\n");
+	/* set reference clock */
+	reg_set(hpipe_addr + HPIPE_MISC_REG,
+		0x0 << HPIPE_MISC_REFCLK_SEL_OFFSET,
+		HPIPE_MISC_REFCLK_SEL_MASK);
+	/* Power and PLL Control */
+	mask = HPIPE_PWR_PLL_REF_FREQ_MASK;
+	data = 0x1 << HPIPE_PWR_PLL_REF_FREQ_OFFSET;
+	mask |= HPIPE_PWR_PLL_PHY_MODE_MASK;
+	data |= 0x4 << HPIPE_PWR_PLL_PHY_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_PLL_REG, data, mask);
+	/* Loopback register */
+	reg_set(hpipe_addr + HPIPE_LOOPBACK_REG,
+		0x1 << HPIPE_LOOPBACK_SEL_OFFSET, HPIPE_LOOPBACK_SEL_MASK);
+	/* rx control 1 */
+	mask = HPIPE_RX_CONTROL_1_RXCLK2X_SEL_MASK;
+	data = 0x1 << HPIPE_RX_CONTROL_1_RXCLK2X_SEL_OFFSET;
+	mask |= HPIPE_RX_CONTROL_1_CLK8T_EN_MASK;
+	data |= 0x1 << HPIPE_RX_CONTROL_1_CLK8T_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_RX_CONTROL_1_REG, data, mask);
+	/* DTL Control */
+	reg_set(hpipe_addr + HPIPE_PWR_CTR_DTL_REG,
+		0x0 << HPIPE_PWR_CTR_DTL_FLOOP_EN_OFFSET,
+		HPIPE_PWR_CTR_DTL_FLOOP_EN_MASK);
+
+	/* Set analog parameters from ETP(HW) */
+	debug("stage: Analog parameters from ETP(HW)\n");
+	/* SERDES External Configuration 2 */
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG2_REG,
+		0x1 << SD_EXTERNAL_CONFIG2_PIN_DFE_EN_OFFSET,
+		SD_EXTERNAL_CONFIG2_PIN_DFE_EN_MASK);
+	/* 0x7-DFE Resolution control */
+	reg_set(hpipe_addr + HPIPE_DFE_REG0, 0x1 << HPIPE_DFE_RES_FORCE_OFFSET,
+		HPIPE_DFE_RES_FORCE_MASK);
+	/* 0xd-G1_Setting_0 */
+	reg_set(hpipe_addr + HPIPE_G1_SET_0_REG,
+		0xd << HPIPE_G1_SET_0_G1_TX_EMPH1_OFFSET,
+		HPIPE_G1_SET_0_G1_TX_EMPH1_MASK);
+	/* 0xE-G1_Setting_1 */
+	mask = HPIPE_G1_SET_1_G1_RX_SELMUPI_MASK;
+	data = 0x1 << HPIPE_G1_SET_1_G1_RX_SELMUPI_OFFSET;
+	mask |= HPIPE_G1_SET_1_G1_RX_SELMUPF_MASK;
+	data |= 0x1 << HPIPE_G1_SET_1_G1_RX_SELMUPF_OFFSET;
+	mask |= HPIPE_G1_SET_1_G1_RX_DFE_EN_MASK;
+	data |= 0x1 << HPIPE_G1_SET_1_G1_RX_DFE_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SET_1_REG, data, mask);
+	/* 0xA-DFE_Reg3 */
+	mask = HPIPE_DFE_F3_F5_DFE_EN_MASK;
+	data = 0x0 << HPIPE_DFE_F3_F5_DFE_EN_OFFSET;
+	mask |= HPIPE_DFE_F3_F5_DFE_CTRL_MASK;
+	data |= 0x0 << HPIPE_DFE_F3_F5_DFE_CTRL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_F3_F5_REG, data, mask);
+
+	/* 0x111-G1_Setting_4 */
+	mask = HPIPE_G1_SETTINGS_4_G1_DFE_RES_MASK;
+	data = 0x1 << HPIPE_G1_SETTINGS_4_G1_DFE_RES_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_4_REG, data, mask);
+
+	debug("stage: RFU configurations- Power Up PLL,Tx,Rx\n");
+	/* SERDES External Configuration */
+	mask = SD_EXTERNAL_CONFIG0_SD_PU_PLL_MASK;
+	data = 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_PLL_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_RX_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_RX_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG0_SD_PU_TX_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG0_SD_PU_TX_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG0_REG, data, mask);
+
+
+	/* check PLL rx & tx ready */
+	addr = sd_ip_addr + SD_EXTERNAL_STATUS0_REG;
+	data = SD_EXTERNAL_STATUS0_PLL_RX_MASK |
+		SD_EXTERNAL_STATUS0_PLL_TX_MASK;
+	mask = data;
+	data = polling_with_timeout(addr, data, mask, 15000, REG_32BIT);
+	if (data != 0) {
+		debug("Read from reg = %lx - value = 0x%x\n",
+		      sd_ip_addr + SD_EXTERNAL_STATUS0_REG, data);
+		ERROR("SD_EXTERNAL_STATUS0_PLL_RX is %d, -\"-_PLL_TX is %d\n",
+		      (data & SD_EXTERNAL_STATUS0_PLL_RX_MASK),
+		      (data & SD_EXTERNAL_STATUS0_PLL_TX_MASK));
+		ret = -ETIMEDOUT;
+	}
+
+	/* RX init */
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG,
+		0x1 << SD_EXTERNAL_CONFIG1_RX_INIT_OFFSET,
+		SD_EXTERNAL_CONFIG1_RX_INIT_MASK);
+
+	/* check that RX init done */
+	addr = sd_ip_addr + SD_EXTERNAL_STATUS0_REG;
+	data = SD_EXTERNAL_STATUS0_RX_INIT_MASK;
+	mask = data;
+	data = polling_with_timeout(addr, data, mask, 100, REG_32BIT);
+	if (data != 0) {
+		debug("Read from reg = %lx - value = 0x%x\n",
+		      sd_ip_addr + SD_EXTERNAL_STATUS0_REG, data);
+		ERROR("SD_EXTERNAL_STATUS0_RX_INIT is 0\n");
+		ret = -ETIMEDOUT;
+	}
+
+	debug("stage: RF Reset\n");
+	/* RF Reset */
+	mask =  SD_EXTERNAL_CONFIG1_RX_INIT_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG1_RX_INIT_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+	data |= 0x1 << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	debug_exit();
+
+	return ret;
+}
+
+static int mvebu_cp110_comphy_usb3_power_on(uint64_t comphy_base,
+				     uint8_t comphy_index, uint32_t comphy_mode)
+{
+	uintptr_t hpipe_addr, comphy_addr, addr;
+	uint32_t mask, data;
+	uint8_t ap_nr, cp_nr, phy_polarity_invert;
+	int ret = 0;
+
+	debug_enter();
+
+	/* Configure PIPE selector for USB3 */
+	mvebu_cp110_comphy_set_pipe_selector(comphy_base, comphy_index,
+					     comphy_mode);
+
+	mvebu_cp110_get_ap_and_cp_nr(&ap_nr, &cp_nr, comphy_base);
+
+	const struct usb_params *usb_static_values =
+			&usb_static_values_tab[ap_nr][cp_nr][comphy_index];
+
+	phy_polarity_invert = usb_static_values->polarity_invert;
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+	comphy_addr = COMPHY_ADDR(comphy_base, comphy_index);
+
+	debug("stage: RFU configurations - hard reset comphy\n");
+	/* RFU configurations - hard reset comphy */
+	mask = COMMON_PHY_CFG1_PWR_UP_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_UP_OFFSET;
+	mask |= COMMON_PHY_CFG1_PIPE_SELECT_MASK;
+	data |= 0x1 << COMMON_PHY_CFG1_PIPE_SELECT_OFFSET;
+	mask |= COMMON_PHY_CFG1_PWR_ON_RESET_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PWR_ON_RESET_OFFSET;
+	mask |= COMMON_PHY_CFG1_CORE_RSTN_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_CORE_RSTN_OFFSET;
+	mask |= COMMON_PHY_PHY_MODE_MASK;
+	data |= 0x1 << COMMON_PHY_PHY_MODE_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* release from hard reset */
+	mask = COMMON_PHY_CFG1_PWR_ON_RESET_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_ON_RESET_OFFSET;
+	mask |= COMMON_PHY_CFG1_CORE_RSTN_MASK;
+	data |= 0x1 << COMMON_PHY_CFG1_CORE_RSTN_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* Wait 1ms - until band gap and ref clock ready */
+	mdelay(1);
+
+	/* Start comphy Configuration */
+	debug("stage: Comphy configuration\n");
+	/* Set PIPE soft reset */
+	mask = HPIPE_RST_CLK_CTRL_PIPE_RST_MASK;
+	data = 0x1 << HPIPE_RST_CLK_CTRL_PIPE_RST_OFFSET;
+	/* Set PHY datapath width mode for V0 */
+	mask |= HPIPE_RST_CLK_CTRL_FIXED_PCLK_MASK;
+	data |= 0x0 << HPIPE_RST_CLK_CTRL_FIXED_PCLK_OFFSET;
+	/* Set Data bus width USB mode for V0 */
+	mask |= HPIPE_RST_CLK_CTRL_PIPE_WIDTH_MASK;
+	data |= 0x0 << HPIPE_RST_CLK_CTRL_PIPE_WIDTH_OFFSET;
+	/* Set CORE_CLK output frequency for 250Mhz */
+	mask |= HPIPE_RST_CLK_CTRL_CORE_FREQ_SEL_MASK;
+	data |= 0x0 << HPIPE_RST_CLK_CTRL_CORE_FREQ_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_RST_CLK_CTRL_REG, data, mask);
+	/* Set PLL ready delay for 0x2 */
+	reg_set(hpipe_addr + HPIPE_CLK_SRC_LO_REG,
+		0x2 << HPIPE_CLK_SRC_LO_PLL_RDY_DL_OFFSET,
+		HPIPE_CLK_SRC_LO_PLL_RDY_DL_MASK);
+	/* Set reference clock to come from group 1 - 25Mhz */
+	reg_set(hpipe_addr + HPIPE_MISC_REG,
+		0x0 << HPIPE_MISC_REFCLK_SEL_OFFSET,
+		HPIPE_MISC_REFCLK_SEL_MASK);
+	/* Set reference frequcency select - 0x2 */
+	mask = HPIPE_PWR_PLL_REF_FREQ_MASK;
+	data = 0x2 << HPIPE_PWR_PLL_REF_FREQ_OFFSET;
+	/* Set PHY mode to USB - 0x5 */
+	mask |= HPIPE_PWR_PLL_PHY_MODE_MASK;
+	data |= 0x5 << HPIPE_PWR_PLL_PHY_MODE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_PWR_PLL_REG, data, mask);
+	/* Set the amount of time spent in the LoZ state - set for 0x7 */
+	reg_set(hpipe_addr + HPIPE_GLOBAL_PM_CTRL,
+		0x7 << HPIPE_GLOBAL_PM_RXDLOZ_WAIT_OFFSET,
+		HPIPE_GLOBAL_PM_RXDLOZ_WAIT_MASK);
+	/* Set max PHY generation setting - 5Gbps */
+	reg_set(hpipe_addr + HPIPE_INTERFACE_REG,
+		0x1 << HPIPE_INTERFACE_GEN_MAX_OFFSET,
+		HPIPE_INTERFACE_GEN_MAX_MASK);
+	/* Set select data width 20Bit (SEL_BITS[2:0]) */
+	reg_set(hpipe_addr + HPIPE_LOOPBACK_REG,
+		0x1 << HPIPE_LOOPBACK_SEL_OFFSET,
+		HPIPE_LOOPBACK_SEL_MASK);
+	/* select de-emphasize 3.5db */
+	reg_set(hpipe_addr + HPIPE_LANE_CONFIG0_REG,
+		0x1 << HPIPE_LANE_CONFIG0_TXDEEMPH0_OFFSET,
+		HPIPE_LANE_CONFIG0_TXDEEMPH0_MASK);
+	/* override tx margining from the MAC */
+	reg_set(hpipe_addr + HPIPE_TST_MODE_CTRL_REG,
+		0x1 << HPIPE_TST_MODE_CTRL_MODE_MARGIN_OFFSET,
+		HPIPE_TST_MODE_CTRL_MODE_MARGIN_MASK);
+
+	/* The polarity inversion for USB was not tested due to lack of hw
+	 * design which requires it. Support is added for customer needs.
+	 */
+	if (phy_polarity_invert)
+		mvebu_cp110_polarity_invert(hpipe_addr + HPIPE_SYNC_PATTERN_REG,
+					    phy_polarity_invert);
+
+	/* Start analog parameters from ETP(HW) */
+	debug("stage: Analog parameters from ETP(HW)\n");
+	/* Set Pin DFE_PAT_DIS -> Bit[1]: PIN_DFE_PAT_DIS = 0x0 */
+	mask = HPIPE_LANE_CFG4_DFE_CTRL_MASK;
+	data = 0x1 << HPIPE_LANE_CFG4_DFE_CTRL_OFFSET;
+	/* Set Override PHY DFE control pins for 0x1 */
+	mask |= HPIPE_LANE_CFG4_DFE_OVER_MASK;
+	data |= 0x1 << HPIPE_LANE_CFG4_DFE_OVER_OFFSET;
+	/* Set Spread Spectrum Clock Enable fot 0x1 */
+	mask |= HPIPE_LANE_CFG4_SSC_CTRL_MASK;
+	data |= 0x1 << HPIPE_LANE_CFG4_SSC_CTRL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_LANE_CFG4_REG, data, mask);
+	/* Confifure SSC amplitude */
+	mask = HPIPE_G2_TX_SSC_AMP_MASK;
+	data = 0x1f << HPIPE_G2_TX_SSC_AMP_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G2_SET_2_REG, data, mask);
+	/* End of analog parameters */
+
+	debug("stage: Comphy power up\n");
+	/* Release from PIPE soft reset */
+	reg_set(hpipe_addr + HPIPE_RST_CLK_CTRL_REG,
+		0x0 << HPIPE_RST_CLK_CTRL_PIPE_RST_OFFSET,
+		HPIPE_RST_CLK_CTRL_PIPE_RST_MASK);
+
+	/* wait 15ms - for comphy calibration done */
+	debug("stage: Check PLL\n");
+	/* Read lane status */
+	addr = hpipe_addr + HPIPE_LANE_STATUS1_REG;
+	data = HPIPE_LANE_STATUS1_PCLK_EN_MASK;
+	mask = data;
+	data = polling_with_timeout(addr, data, mask, 15000, REG_32BIT);
+	if (data != 0) {
+		debug("Read from reg = %lx - value = 0x%x\n",
+			hpipe_addr + HPIPE_LANE_STATUS1_REG, data);
+		ERROR("HPIPE_LANE_STATUS1_PCLK_EN_MASK is 0\n");
+		ret = -ETIMEDOUT;
+	}
+
+	debug_exit();
+
+	return ret;
+}
+
+static void rx_pre_train(uint64_t comphy_base, uint8_t comphy_index)
+{
+	uintptr_t hpipe_addr;
+	uint32_t mask, data;
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+
+	debug("rx_training preparation\n\n");
+
+	mask = HPIPE_TRX0_GAIN_TRAIN_WITH_C_MASK;
+	data = (0x1 << HPIPE_TRX0_GAIN_TRAIN_WITH_C_OFF);
+	mask |= HPIPE_TRX0_GAIN_TRAIN_WITH_SAMPLER_MASK;
+	data |= (0x0 << HPIPE_TRX0_GAIN_TRAIN_WITH_SAMPLER_OFF);
+	reg_set(hpipe_addr + HPIPE_TRX0_REG, data, mask);
+
+
+	mask = HPIPE_TRX_REG2_SUMF_BOOST_TARGET_C_MASK;
+	data = (0x1e << HPIPE_TRX_REG2_SUMF_BOOST_TARGET_C_OFF);
+	mask |= HPIPE_TRX_REG2_SUMF_BOOST_TARGET_K_MASK;
+	data |= (0x0 << HPIPE_TRX_REG2_SUMF_BOOST_TARGET_K_OFF);
+	reg_set(hpipe_addr + HPIPE_TRX_REG2, data, mask);
+
+	mask = HPIPE_TRX_REG1_MIN_BOOST_MODE_MASK;
+	data = (0x1 << HPIPE_TRX_REG1_MIN_BOOST_MODE_OFF);
+	reg_set(hpipe_addr + HPIPE_TRX_REG1, data, mask);
+
+	mask = HPIPE_CRD2_CRD_MIDPOINT_SMALL_THRES_K_MASK;
+	data = (0x8 << HPIPE_CRD2_CRD_MIDPOINT_SMALL_THRES_K_OFF);
+	reg_set(hpipe_addr + HPIPE_CDR_CONTROL1_REG, data, mask);
+
+	mask = HPIPE_CRD2_CRD_MIDPOINT_LARGE_THRES_K_MASK;
+	data = (0x8 << HPIPE_CRD2_CRD_MIDPOINT_LARGE_THRES_K_OFF);
+	reg_set(hpipe_addr + HPIPE_CDR_CONTROL2_REG, data, mask);
+
+	mask = HPIPE_CRD_MIDPOINT_PHASE_OS_MASK;
+	data = (0x0 << HPIPE_CRD_MIDPOINT_PHASE_OS_OFFSET);
+	reg_set(hpipe_addr + HPIPE_CDR_CONTROL_REG, data, mask);
+
+	mask = HPIPE_TRX_REG1_SUMFTAP_EN_MASK;
+	data = (0x38 << HPIPE_TRX_REG1_SUMFTAP_EN_OFF);
+	mask |= HPIPE_TRX_REG2_SUMF_BOOST_TARGET_C_MASK;
+	data |= (0x1e << HPIPE_TRX_REG2_SUMF_BOOST_TARGET_C_OFF);
+	reg_set(hpipe_addr + HPIPE_TRX_REG1, data, mask);
+}
+
+int mvebu_cp110_comphy_xfi_rx_training(uint64_t comphy_base,
+					      uint8_t comphy_index)
+{
+	uint32_t mask, data, timeout;
+	uint32_t g1_ffe_cap_sel, g1_ffe_res_sel, align90, g1_dfe_res;
+	uintptr_t hpipe_addr;
+
+	uint8_t ap_nr, cp_nr;
+
+	mvebu_cp110_get_ap_and_cp_nr(&ap_nr, &cp_nr, comphy_base);
+
+	hpipe_addr = HPIPE_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+				comphy_index);
+
+	debug_enter();
+
+	rx_pre_train(comphy_base, comphy_index);
+
+	debug("Preparation for rx_training\n\n");
+
+	/* Use the FFE table */
+	mask = HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_MASK;
+	data = 0 << HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_3_REG, data, mask);
+
+	/* Use auto-calibration value */
+	mask = HPIPE_CAL_RXCLKALIGN_90_EXT_EN_MASK;
+	data = 0 << HPIPE_CAL_RXCLKALIGN_90_EXT_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_RX_CLK_ALIGN90_AND_TX_IDLE_CALIB_CTRL_REG,
+		data, mask);
+
+	/* Use Tx/Rx training results */
+	mask = HPIPE_DFE_RES_FORCE_MASK;
+	data = 0 << HPIPE_DFE_RES_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_REG0, data, mask);
+
+	debug("Enable RX training\n\n");
+
+	mask = HPIPE_TRX_RX_TRAIN_EN_MASK;
+	data = 0x1 << HPIPE_TRX_RX_TRAIN_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TRX_TRAIN_CTRL_0_REG, data, mask);
+
+	/* Check the result of RX training */
+	timeout = RX_TRAINING_TIMEOUT;
+	mask = HPIPE_INTERRUPT_TRX_TRAIN_DONE_OFFSET |
+		HPIPE_INTERRUPT_DFE_DONE_INT_OFFSET |
+		HPIPE_INTERRUPT_RX_TRAIN_COMPLETE_INT_MASK;
+	while (timeout) {
+		data = mmio_read_32(hpipe_addr + HPIPE_INTERRUPT_1_REGISTER);
+		if (data & mask)
+			break;
+		mdelay(1);
+		timeout--;
+	}
+
+	debug("RX training result: interrupt reg 0x%lx = 0x%x\n\n",
+	       hpipe_addr + HPIPE_INTERRUPT_1_REGISTER, data);
+
+	if (timeout == 0 || data & HPIPE_TRX_TRAIN_TIME_OUT_INT_MASK) {
+		ERROR("Rx training timeout...\n");
+		return -ETIMEDOUT;
+	}
+
+	if (data & HPIPE_TRX_TRAIN_FAILED_MASK) {
+		ERROR("Rx training failed...\n");
+		return -EINVAL;
+	}
+
+	mask = HPIPE_TRX_RX_TRAIN_EN_MASK;
+	data = 0x0 << HPIPE_TRX_RX_TRAIN_EN_OFFSET;
+	reg_set(hpipe_addr + HPIPE_TRX_TRAIN_CTRL_0_REG, data, mask);
+
+	debug("Training done, reading results...\n\n");
+
+	mask = HPIPE_ADAPTED_FFE_ADAPTED_FFE_RES_MASK;
+	g1_ffe_res_sel = ((mmio_read_32(hpipe_addr +
+			   HPIPE_ADAPTED_FFE_CAPACITOR_COUNTER_CTRL_REG)
+			   & mask) >> HPIPE_ADAPTED_FFE_ADAPTED_FFE_RES_OFFSET);
+
+	mask = HPIPE_ADAPTED_FFE_ADAPTED_FFE_CAP_MASK;
+	g1_ffe_cap_sel = ((mmio_read_32(hpipe_addr +
+			   HPIPE_ADAPTED_FFE_CAPACITOR_COUNTER_CTRL_REG)
+			   & mask) >> HPIPE_ADAPTED_FFE_ADAPTED_FFE_CAP_OFFSET);
+
+	mask = HPIPE_DATA_PHASE_ADAPTED_OS_PH_MASK;
+	align90 = ((mmio_read_32(hpipe_addr + HPIPE_DATA_PHASE_OFF_CTRL_REG)
+		    & mask) >> HPIPE_DATA_PHASE_ADAPTED_OS_PH_OFFSET);
+
+	mask = HPIPE_ADAPTED_DFE_RES_MASK;
+	g1_dfe_res = ((mmio_read_32(hpipe_addr +
+		       HPIPE_ADAPTED_DFE_COEFFICIENT_1_REG)
+		       & mask) >> HPIPE_ADAPTED_DFE_RES_OFFSET);
+
+	debug("================================================\n");
+	debug("Switching to static configuration:\n");
+	debug("FFE_RES = 0x%x FFE_CAP = 0x%x align90 = 0x%x g1_dfe_res 0x%x\n",
+	       g1_ffe_res_sel, g1_ffe_cap_sel, align90, g1_dfe_res);
+	debug("Result after training: 0x%lx= 0x%x, 0x%lx= 0x%x, 0x%lx = 0x%x\n",
+	      (hpipe_addr + HPIPE_ADAPTED_FFE_CAPACITOR_COUNTER_CTRL_REG),
+	       mmio_read_32(hpipe_addr +
+			    HPIPE_ADAPTED_FFE_CAPACITOR_COUNTER_CTRL_REG),
+			    (hpipe_addr + HPIPE_DATA_PHASE_OFF_CTRL_REG),
+	       mmio_read_32(hpipe_addr + HPIPE_DATA_PHASE_OFF_CTRL_REG),
+			    (hpipe_addr + HPIPE_ADAPTED_DFE_COEFFICIENT_1_REG),
+	       mmio_read_32(hpipe_addr + HPIPE_ADAPTED_DFE_COEFFICIENT_1_REG));
+	debug("================================================\n");
+
+	/* Update FFE_RES */
+	mask = HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_MASK;
+	data = g1_ffe_res_sel << HPIPE_G1_SETTINGS_3_G1_FFE_RES_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_3_REG, data, mask);
+
+	/* Update FFE_CAP */
+	mask = HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_MASK;
+	data = g1_ffe_cap_sel << HPIPE_G1_SETTINGS_3_G1_FFE_CAP_SEL_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_3_REG, data, mask);
+
+	/* Bypass the FFE table settings and use the FFE settings directly from
+	 * registers FFE_RES_SEL and FFE_CAP_SEL
+	 */
+	mask = HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_MASK;
+	data = 1 << HPIPE_G1_SETTINGS_3_G1_FFE_SETTING_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_3_REG, data, mask);
+
+	/* Force DFE resolution (use gen table value) */
+	mask = HPIPE_DFE_RES_FORCE_MASK;
+	data = 0x1 << HPIPE_DFE_RES_FORCE_OFFSET;
+	reg_set(hpipe_addr + HPIPE_DFE_REG0, data, mask);
+
+	/* 0x111-G1 DFE_Setting_4 */
+	mask = HPIPE_G1_SETTINGS_4_G1_DFE_RES_MASK;
+	data = g1_dfe_res << HPIPE_G1_SETTINGS_4_G1_DFE_RES_OFFSET;
+	reg_set(hpipe_addr + HPIPE_G1_SETTINGS_4_REG, data, mask);
+
+	printf("########################################################\n");
+	printf("# To use trained values update the ATF sources:\n");
+	printf("# plat/marvell/armada/a8k/<board_type>/board/phy-porting-layer.h ");
+	printf("file\n# with new values as below (for appropriate AP nr %d",
+	       ap_nr);
+	printf("and CP nr: %d comphy_index %d\n\n",
+	       cp_nr, comphy_index);
+	printf("static struct xfi_params xfi_static_values_tab[AP_NUM]");
+	printf("[CP_NUM][MAX_LANE_NR] = {\n");
+	printf("\t...\n");
+	printf("\t.g1_ffe_res_sel = 0x%x,\n", g1_ffe_res_sel);
+	printf("\t.g1_ffe_cap_sel = 0x%x,\n", g1_ffe_cap_sel);
+	printf("\t.align90 = 0x%x,\n", align90);
+	printf("\t.g1_dfe_res = 0x%x\n", g1_dfe_res);
+	printf("\t...\n");
+	printf("};\n\n");
+	printf("########################################################\n");
+
+	rx_trainng_done[ap_nr][cp_nr][comphy_index] = 1;
+
+	return 0;
+}
+
+/* During AP the proper mode is auto-negotiated and the mac, pcs and serdes
+ * configuration are done by the firmware loaded to the MG's CM3 for appropriate
+ * negotiated mode. Therefore there is no need to configure the mac, pcs and
+ * serdes from u-boot. The only thing that need to be setup is powering up
+ * the comphy, which is done through Common PHY<n> Configuration 1 Register
+ * (CP0: 0xF2441000, CP1: 0xF4441000). This step can't be done by MG's CM3,
+ * since it doesn't have an access to this register-set (but it has access to
+ * the network registers like: MG, AP, MAC, PCS, Serdes etc.)
+ */
+static int mvebu_cp110_comphy_ap_power_on(uint64_t comphy_base,
+					  uint8_t comphy_index,
+					  uint32_t comphy_mode)
+{
+	uint32_t mask, data;
+	uintptr_t comphy_addr = comphy_addr =
+				COMPHY_ADDR(comphy_base, comphy_index);
+
+	/* configure phy selector for XFI/SFI */
+	mvebu_cp110_comphy_set_phy_selector(comphy_base, comphy_index,
+					    comphy_mode);
+	debug_enter();
+	debug("stage: RFU configurations - hard reset comphy\n");
+	/* RFU configurations - hard reset comphy */
+	mask = COMMON_PHY_CFG1_PWR_UP_MASK;
+	data = 0x1 << COMMON_PHY_CFG1_PWR_UP_OFFSET;
+	mask |= COMMON_PHY_CFG1_PIPE_SELECT_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_PIPE_SELECT_OFFSET;
+	reg_set(comphy_addr + COMMON_PHY_CFG1_REG, data, mask);
+	debug_exit();
+
+#if MSS_SUPPORT
+	do {
+		uint8_t ap_nr, cp_nr;
+
+		/* start ap fw */
+		mvebu_cp110_get_ap_and_cp_nr(&ap_nr, &cp_nr, comphy_base);
+		mg_start_ap_fw(cp_nr, comphy_index);
+
+	} while (0);
+#endif
+	return 0;
+}
+
+/*
+ * This function allows to reset the digital synchronizers between
+ * the MAC and the PHY, it is required when the MAC changes its state.
+ */
+int mvebu_cp110_comphy_digital_reset(uint64_t comphy_base,
+				     uint8_t comphy_index,
+				     uint32_t comphy_mode, uint32_t command)
+{
+	int mode = COMPHY_GET_MODE(comphy_mode);
+	uintptr_t sd_ip_addr;
+	uint32_t mask, data;
+
+	sd_ip_addr = SD_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+			     comphy_index);
+
+	switch (mode) {
+	case (COMPHY_SGMII_MODE):
+	case (COMPHY_2500BASEX_MODE):
+	case (COMPHY_XFI_MODE):
+	case (COMPHY_SFI_MODE):
+	case (COMPHY_RXAUI_MODE):
+		mask = SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+		data = ((command == COMPHY_COMMAND_DIGITAL_PWR_OFF) ?
+			0x0 : 0x1) << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+		reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+		break;
+	default:
+		ERROR("comphy%d: Digital PWR ON/OFF is not supported\n",
+			comphy_index);
+			return -EINVAL;
+	}
+
+	return 0;
+}
+
+int mvebu_cp110_comphy_power_on(uint64_t comphy_base,
+				uint8_t comphy_index,
+				uint64_t comphy_mode,
+				uint64_t comphy_train_base)
+{
+	int mode = COMPHY_GET_MODE(comphy_mode);
+	int err = 0;
+
+	debug_enter();
+
+	switch (mode) {
+	case(COMPHY_SATA_MODE):
+		err = mvebu_cp110_comphy_sata_power_on(comphy_base,
+						       comphy_index,
+						       comphy_mode);
+		break;
+	case(COMPHY_SGMII_MODE):
+	case(COMPHY_2500BASEX_MODE):
+		err = mvebu_cp110_comphy_sgmii_power_on(comphy_base,
+							comphy_index,
+							comphy_mode);
+		break;
+	/* From comphy perspective, XFI and SFI are the same */
+	case (COMPHY_XFI_MODE):
+	case (COMPHY_SFI_MODE):
+		err = mvebu_cp110_comphy_xfi_power_on(comphy_base,
+						      comphy_index,
+						      comphy_mode,
+						      comphy_train_base);
+		break;
+	case (COMPHY_PCIE_MODE):
+		err = mvebu_cp110_comphy_pcie_power_on(comphy_base,
+						       comphy_index,
+						       comphy_mode);
+		break;
+	case (COMPHY_RXAUI_MODE):
+		err = mvebu_cp110_comphy_rxaui_power_on(comphy_base,
+							comphy_index,
+							comphy_mode);
+		break;
+	case (COMPHY_USB3H_MODE):
+	case (COMPHY_USB3D_MODE):
+		err = mvebu_cp110_comphy_usb3_power_on(comphy_base,
+						       comphy_index,
+						       comphy_mode);
+		break;
+	case (COMPHY_AP_MODE):
+		err = mvebu_cp110_comphy_ap_power_on(comphy_base, comphy_index,
+						     comphy_mode);
+		break;
+	default:
+		ERROR("comphy%d: unsupported comphy mode\n", comphy_index);
+		err = -EINVAL;
+		break;
+	}
+
+	debug_exit();
+
+	return err;
+}
+
+int mvebu_cp110_comphy_power_off(uint64_t comphy_base, uint8_t comphy_index,
+				 uint64_t comphy_mode)
+{
+	uintptr_t sd_ip_addr, comphy_ip_addr;
+	uint32_t mask, data;
+	uint8_t ap_nr, cp_nr;
+	_Bool called_from_uboot = COMPHY_GET_CALLER(comphy_mode);
+
+	debug_enter();
+
+	/* Power-off might happen because of 2 things:
+	 *	1. Bootloader turns off unconnected lanes
+	 *	2. Linux turns off all lanes during boot
+	 *	   (and then reconfigure it).
+	 *
+	 * For PCIe, there's a problem:
+	 * In Armada 8K DB boards, PCIe initialization can be executed
+	 * only once (PCIe reset performed during chip power on and
+	 * it cannot be executed via GPIO later) so a lane configured to
+	 * PCIe should not be powered off by Linux.
+	 *
+	 * So, check 2 things:
+	 *	1. Is Linux called for power-off?
+	 *	2. Is the comphy configured to PCIe?
+	 * If the answer is YES for both 1 and 2, skip the power-off.
+	 *
+	 * TODO: In MacciatoBIN, PCIe reset is connected via GPIO,
+	 * so after GPIO reset is added to Linux Kernel, it can be
+	 * powered-off.
+	 */
+	if (!called_from_uboot) {
+		data = mmio_read_32(comphy_base +
+				    COMMON_SELECTOR_PIPE_REG_OFFSET);
+		data >>= (COMMON_SELECTOR_COMPHYN_FIELD_WIDTH * comphy_index);
+		data &= COMMON_SELECTOR_COMPHY_MASK;
+		if (data == COMMON_SELECTOR_PIPE_COMPHY_PCIE)
+			return 0;
+	}
+
+	mvebu_cp110_get_ap_and_cp_nr(&ap_nr, &cp_nr, comphy_base);
+
+	if (rx_trainng_done[ap_nr][cp_nr][comphy_index]) {
+		debug("Skip %s for comphy[%d][%d][%d], due to rx training\n",
+		       __func__, ap_nr, cp_nr, comphy_index);
+		return 0;
+	}
+
+	sd_ip_addr = SD_ADDR(COMPHY_PIPE_FROM_COMPHY_ADDR(comphy_base),
+			     comphy_index);
+	comphy_ip_addr = COMPHY_ADDR(comphy_base, comphy_index);
+
+	/* Hard reset the comphy, for Ethernet modes and Sata */
+	mask = SD_EXTERNAL_CONFIG1_RESET_IN_MASK;
+	data = 0x0 << SD_EXTERNAL_CONFIG1_RESET_IN_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RESET_CORE_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RESET_CORE_OFFSET;
+	mask |= SD_EXTERNAL_CONFIG1_RF_RESET_IN_MASK;
+	data |= 0x0 << SD_EXTERNAL_CONFIG1_RF_RESET_IN_OFFSET;
+	reg_set(sd_ip_addr + SD_EXTERNAL_CONFIG1_REG, data, mask);
+
+	/* PCIe reset */
+	spin_lock(&cp110_mac_reset_lock);
+
+	/* The mvebu_cp110_comphy_power_off will be called only from Linux (to
+	 * override settings done by bootloader) and it will be relevant only
+	 * to PCIe (called before check if to skip pcie power off or not).
+	 */
+	data = mmio_read_32(SYS_CTRL_FROM_COMPHY_ADDR(comphy_base) +
+						 SYS_CTRL_UINIT_SOFT_RESET_REG);
+	switch (comphy_index) {
+	case COMPHY_LANE0:
+		data &= ~PCIE_MAC_RESET_MASK_PORT0;
+		break;
+	case COMPHY_LANE4:
+		data &= ~PCIE_MAC_RESET_MASK_PORT1;
+		break;
+	case COMPHY_LANE5:
+		data &= ~PCIE_MAC_RESET_MASK_PORT2;
+		break;
+	}
+
+	mmio_write_32(SYS_CTRL_FROM_COMPHY_ADDR(comphy_base) +
+					   SYS_CTRL_UINIT_SOFT_RESET_REG, data);
+	spin_unlock(&cp110_mac_reset_lock);
+
+	/* Hard reset the comphy, for PCIe and usb3 */
+	mask = COMMON_PHY_CFG1_PWR_ON_RESET_MASK;
+	data = 0x0 << COMMON_PHY_CFG1_PWR_ON_RESET_OFFSET;
+	mask |= COMMON_PHY_CFG1_CORE_RSTN_MASK;
+	data |= 0x0 << COMMON_PHY_CFG1_CORE_RSTN_OFFSET;
+	reg_set(comphy_ip_addr + COMMON_PHY_CFG1_REG, data, mask);
+
+	/* Clear comphy PHY and PIPE selector, can't rely on previous config. */
+	mvebu_cp110_comphy_clr_phy_selector(comphy_base, comphy_index);
+	mvebu_cp110_comphy_clr_pipe_selector(comphy_base, comphy_index);
+
+	debug_exit();
+
+	return 0;
+}