diff options
Diffstat (limited to '')
| -rw-r--r-- | docs/plat/qti-msm8916.rst | 116 |
1 files changed, 116 insertions, 0 deletions
diff --git a/docs/plat/qti-msm8916.rst b/docs/plat/qti-msm8916.rst new file mode 100644 index 0000000..09a79b7 --- /dev/null +++ b/docs/plat/qti-msm8916.rst @@ -0,0 +1,116 @@ +Qualcomm Snapdragon 410 (MSM8916/APQ8016) +========================================= + +The `Qualcomm Snapdragon 410`_ is Qualcomm's first 64-bit SoC, released in 2014 +with four ARM Cortex-A53 cores. There are differents variants (MSM8916, +APQ8016(E), ...) that are all very similar. A popular device based on APQ8016E +is the `DragonBoard 410c`_ single-board computer, but the SoC is also used in +various mid-range smartphones/tablets. + +The TF-A/BL31 port for MSM8916 provides a minimal, community-maintained +EL3 firmware. It is primarily based on information from the public +`Snapdragon 410E Technical Reference Manual`_ combined with a lot of +trial and error to actually make it work. + +.. note:: + Unlike the :doc:`QTI SC7180/SC7280 <qti>` ports, this port does **not** + make use of a proprietary binary components (QTISECLIB). It is fully + open-source but therefore limited to publicly documented hardware + components. + +Functionality +------------- + +The BL31 port is much more minimal compared to the original firmware and +therefore expects the non-secure world (e.g. Linux) to manage more hardware, +such as the SMMUs and all remote processors (RPM, WCNSS, Venus, Modem). +Everything except modem is currently functional with a slightly modified version +of mainline Linux. + +.. warning:: + This port is **not secure**. There is no special secure memory and the + used DRAM is available from both the non-secure and secure worlds. + Unfortunately, the hardware used for memory protection is not described + in the APQ8016E documentation. + +The port is primarily intended as a minimal PSCI implementation (without a +separate secure world) where this limitation is not a big problem. Booting +secondary CPU cores (PSCI ``CPU_ON``) is supported. Basic CPU core power +management (``CPU_SUSPEND``) is functional but still work-in-progress and +will be added later once ready. + +Boot Flow +--------- +BL31 replaces the original ``tz`` firmware in the boot flow:: + + Boot ROM (PBL) -> SBL -> BL31 (EL3) -> U-Boot (EL2) -> Linux (EL2) + +By default, BL31 enters the non-secure world in EL2 AArch64 state at address +``0x8f600000``. The original hypervisor firmware (``hyp``) is not used, you can +use KVM or another hypervisor. The entry address is fixed in the BL31 binary +but can be changed using the ``PRELOADED_BL33_BASE`` make file parameter. + +Using an AArch64 bootloader (such as `U-Boot for DragonBoard 410c`_) is +recommended. AArch32 bootloaders (such as the original Little Kernel bootloader +from Qualcomm) are not directly supported, although it is possible to use an EL2 +shim loader to temporarily switch to AArch32 state. + +Installation +------------ +First, setup the cross compiler for AArch64 and build TF-A for ``msm8916``:: + + $ make CROSS_COMPILE=aarch64-linux-gnu- PLAT=msm8916 + +The BL31 ELF image is generated in ``build/msm8916/release/bl31/bl31.elf``. +This image must be "signed" before flashing it, even if the board has secure +boot disabled. In this case the signature does not provide any security, +but it provides the firmware with required metadata. + +The `DragonBoard 410c`_ does not have secure boot enabled by default. In this +case you can simply sign the ELF image using a randomly generated key. You can +use e.g. `qtestsign`_:: + + $ ./qtestsign.py tz build/msm8916/release/bl31/bl31.elf + +Then install the resulting ``build/msm8916/release/bl31/bl31-test-signed.mbn`` +to the ``tz`` partition on the device. BL31 should be running after a reboot. + +.. warning:: + Do not flash incorrectly signed firmware on devices that have secure + boot enabled! Make sure that you have a way to recover the board in case + of problems (e.g. using EDL). + +Boot Trace +---------- +BL31 prints some lines on the debug console UART2, which will usually look like +this (with ``DEBUG=1``, otherwise only the ``NOTICE`` lines are shown):: + + ... + S - DDR Frequency, 400 MHz + NOTICE: BL31: v2.6(debug):v2.6 + NOTICE: BL31: Built : 20:00:00, Dec 01 2021 + INFO: BL31: Platform setup start + INFO: ARM GICv2 driver initialized + INFO: BL31: Platform setup done + INFO: BL31: Initializing runtime services + INFO: BL31: cortex_a53: CPU workaround for 819472 was applied + INFO: BL31: cortex_a53: CPU workaround for 824069 was applied + INFO: BL31: cortex_a53: CPU workaround for 826319 was applied + INFO: BL31: cortex_a53: CPU workaround for 827319 was applied + INFO: BL31: cortex_a53: CPU workaround for 835769 was applied + INFO: BL31: cortex_a53: CPU workaround for disable_non_temporal_hint was applied + INFO: BL31: cortex_a53: CPU workaround for 843419 was applied + INFO: BL31: cortex_a53: CPU workaround for 1530924 was applied + INFO: BL31: Preparing for EL3 exit to normal world + INFO: Entry point address = 0x8f600000 + INFO: SPSR = 0x3c9 + + U-Boot 2021.10 (Dec 01 2021 - 20:00:00 +0000) + Qualcomm-DragonBoard 410C + ... + +.. _Qualcomm Snapdragon 410: https://www.qualcomm.com/products/snapdragon-processors-410 +.. _DragonBoard 410c: https://www.96boards.org/product/dragonboard410c/ +.. _Snapdragon 410E Technical Reference Manual: https://developer.qualcomm.com/download/sd410/snapdragon-410e-technical-reference-manual.pdf +.. _U-Boot for DragonBoard 410c: https://u-boot.readthedocs.io/en/latest/board/qualcomm/dragonboard410c.html +.. _qtestsign: https://github.com/msm8916-mainline/qtestsign |