Allwinner ARMv8 SoCs ==================== Trusted Firmware-A (TF-A) implements the EL3 firmware layer for Allwinner SoCs with ARMv8 cores. Only BL31 is used to provide proper EL3 setup and PSCI runtime services. Building TF-A ------------- There is one build target per supported SoC: +------+-------------------+ | SoC | TF-A build target | +======+===================+ | A64 | sun50i_a64 | +------+-------------------+ | H5 | sun50i_a64 | +------+-------------------+ | H6 | sun50i_h6 | +------+-------------------+ | H616 | sun50i_h616 | +------+-------------------+ | H313 | sun50i_h616 | +------+-------------------+ | R329 | sun50i_r329 | +------+-------------------+ To build with the default settings for a particular SoC: .. code:: shell make CROSS_COMPILE=aarch64-linux-gnu- PLAT= DEBUG=1 So for instance to build for a board with the Allwinner A64 SoC:: make CROSS_COMPILE=aarch64-linux-gnu- PLAT=sun50i_a64 DEBUG=1 Platform-specific build options ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ The default build options should generate a working firmware image. There are some build options that allow to fine-tune the firmware, or to disable support for optional features. - ``SUNXI_PSCI_USE_NATIVE`` : Support direct control of the CPU cores powerdown and powerup sequence by BL31. This requires either support for a code snippet to be loaded into the ARISC SCP (A64, H5), or the power sequence control registers to be programmed directly (H6, H616). This supports only basic control, like core on/off and system off/reset. This option defaults to 1. If an active SCP supporting the SCPI protocol is detected at runtime, this control scheme will be ignored, and SCPI will be used instead, unless support has been explicitly disabled. - ``SUNXI_PSCI_USE_SCPI`` : Support control of the CPU cores powerdown and powerup sequence by talking to the SCP processor via the SCPI protocol. This allows more advanced power saving techniques, like suspend to RAM. This option defaults to 1 on SoCs that feature an SCP. If no SCP firmware using the SCPI protocol is detected, the native sequence will be used instead. If both native and SCPI methods are included, SCPI will be favoured if SCP support is detected. - ``SUNXI_SETUP_REGULATORS`` : On SoCs that typically ship with a PMIC power management controller, BL31 tries to set up all needed power rails, programming them to their respective voltages. That allows bootloader software like U-Boot to ignore power control via the PMIC. This setting defaults to 1. In some situations that enables too many regulators, or some regulators need to be enabled in a very specific sequence. To avoid problems with those boards, ``SUNXI_SETUP_REGULATORS`` can bet set to ``0`` on the build command line, to skip the PMIC setup entirely. Any bootloader or OS would need to setup the PMIC on its own then. Installation ------------ U-Boot's SPL acts as a loader, loading both BL31 and BL33 (typically U-Boot). Loading is done from SD card, eMMC or SPI flash, also via an USB debug interface (FEL). After building bl31.bin, the binary must be fed to the U-Boot build system to include it in the FIT image that the SPL loader will process. bl31.bin can be either copied (or sym-linked) into U-Boot's root directory, or the environment variable BL31 must contain the binary's path. See the respective `U-Boot documentation`_ for more details. .. _U-Boot documentation: https://gitlab.denx.de/u-boot/u-boot/-/blob/master/board/sunxi/README.sunxi64 Memory layout ------------- A64, H5 and H6 SoCs ~~~~~~~~~~~~~~~~~~~ BL31 lives in SRAM A2, which is documented to be accessible from secure world only. Since this SRAM region is very limited (48 KB), we take several measures to reduce memory consumption. One of them is to confine BL31 to only 28 bits of virtual address space, which reduces the number of required page tables (each occupying 4KB of memory). The mapping we use on those SoCs is as follows: :: 0 64K 16M 1GB 1G+160M physical address +-+------+-+---+------+--...---+-------+----+------+---------- |B| |S|///| |//...///| |////| | |R| SRAM |C|///| dev |//...///| (sec) |////| BL33 | DRAM ... |O| |P|///| MMIO |//...///| DRAM |////| | |M| | |///| |//...///| (32M) |////| | +-+------+-+---+------+--...---+-------+----+------+---------- | | | | | | / / / / | | | | | | / / / / | | | | | | / / / / | | | | | | / // / | | | | | | / / / +-+------+-+---+------+--+-------+------+ |B| |S|///| |//| | | |R| SRAM |C|///| dev |//| sec | BL33 | |O| |P|///| MMIO |//| DRAM | | |M| | |///| |//| | | +-+------+-+---+------+--+-------+------+ 0 64K 16M 160M 192M 256M virtual address H616 SoC ~~~~~~~~ The H616 lacks the secure SRAM region present on the other SoCs, also lacks the "ARISC" management processor (SCP) we use. BL31 thus needs to run from DRAM, which prevents our compressed virtual memory map described above. Since running in DRAM also lifts the restriction of the limited SRAM size, we use the normal 1:1 mapping with 32 bits worth of virtual address space. So the virtual addresses used in BL31 match the physical addresses as presented above. Trusted OS dispatcher --------------------- One can boot Trusted OS(OP-TEE OS, bl32 image) along side bl31 image on Allwinner A64. In order to include the 'opteed' dispatcher in the image, pass 'SPD=opteed' on the command line while compiling the bl31 image and make sure the loader (SPL) loads the Trusted OS binary to the beginning of DRAM (0x40000000).