diff options
Diffstat (limited to 'carl9170fw/carlfw/Kconfig')
| -rw-r--r-- | carl9170fw/carlfw/Kconfig | 233 |
1 files changed, 233 insertions, 0 deletions
diff --git a/carl9170fw/carlfw/Kconfig b/carl9170fw/carlfw/Kconfig new file mode 100644 index 0000000..f42268c --- /dev/null +++ b/carl9170fw/carlfw/Kconfig @@ -0,0 +1,233 @@ +menu "General" + +config CARL9170FW_RELEASE_VERSION + int + default 1 + +menu "Selectable Hardware Options" + +choice + prompt "Receiver Max. Frame Length" + default CARL9170FW_RX_FRAME_LEN_8192 + + config CARL9170FW_RX_FRAME_LEN_4096 + bool "4096" + + config CARL9170FW_RX_FRAME_LEN_8192 + bool "8192" + + config CARL9170FW_RX_FRAME_LEN_16384 + bool "16384" + + config CARL9170FW_RX_FRAME_LEN_32768 + bool "32768" + +endchoice + +config CARL9170FW_RX_FRAME_LEN + int + default 4096 if CARL9170FW_RX_FRAME_LEN_4096 + default 8192 if CARL9170FW_RX_FRAME_LEN_8192 + default 16384 if CARL9170FW_RX_FRAME_LEN_16384 + default 32768 if CARL9170FW_RX_FRAME_LEN_32768 + +config CARL9170FW_GPIO_INTERRUPT + def_bool y + prompt "GPIO Software Interrupt" + ---help--- + When this option is enabled, the firmware will poll the GPIO + registers and reports to the driver whenever the GPIO state + has changed from a previous state. + + Note: This feature is necessary to monitor the WPS button, + if you have one on your device, then say Y. + +config CARL9170FW_SECURITY_ENGINE + def_bool y + prompt "Support Hardware Crypto Engine" + ---help--- + This options controls if the firmware will allow the driver + to program the security engine / CAM through a firmware + interface. + + Say Y. Unless you want to do the en- and decryption for + CCMP(AES), TKIP/WEP(RC4) in the application anyway. + +config CARL9170FW_RADIO_FUNCTIONS + def_bool y + prompt "Enable Firmware-supported Radio/RF functions" + ---help--- + Some PHY/RF functions (e.g.: AGC and Noise calibration) need + to be done in the firmware. + + Say Y, unless you really don't need the Radio/RF for + your project. + +endmenu + +menu "802.11 Firmware Features" + +config CARL9170FW_CAB_QUEUE + def_bool y + prompt "Support software-based Content after Beacon Queue" + ---help--- + This (software) queue is used to send any broad-/multi-cast buffered + frames after the next DTIM beacon. + + This feature is required for Accesspoint mode operation. + + Say Y. + +endmenu + +source "carlfw/usb/Kconfig" + +menu "Experimental, Unstable & Testing Extensions" + +config CARL9170FW_PRINTF + def_bool y + prompt "Advanced printf" + depends on CARL9170FW_DEBUG_UART || CARL9170FW_DEBUG_USB + ---help--- + Advanced printf (very useful for debugging purposes) + The formats supported by this implementation are: + 'd' 'u' 'c' 's' 'x' 'X' 'p'. + + Note: If this option is disabled, the firmware will be only + capable of reported _preformated_ string. + +config CARL9170FW_EXPERIMENTAL + def_bool y + prompt "Experimental Features" + +config CARL9170FW_WOL_OPTION + def_bool n + prompt "Wakeup on WLAN" + depends on CARL9170FW_EXPERIMENTAL + ---help--- + With this option enabled, the firmware can wake-up + suspended hosts... As long as they fully support + USB remote wakeup. + +config CARL9170FW_WOL + def_bool n + depends on CARL9170FW_WOL_OPTION + +config CARL9170FW_WOL_NL80211_TRIGGERS + def_bool n + prompt "Standard NL80211 wakeup triggers" + depends on CARL9170FW_WOL_OPTION + select CARL9170FW_WOL + ---help--- + Available triggers: + * Magic Packet(tm) pattern + * disconnect event + +config CARL9170FW_WOL_PROBE_REQUEST + def_bool n + prompt "Probe Request" + depends on CARL9170FW_WOL_OPTION + select CARL9170FW_WOL + ---help--- + Scan probe requests for a given SSID. + +config CARL9170FW_WOL_PROBE_REQUEST_SSID + string + prompt "Wakeup on WLAN SSID" + default "CARL9170_WAKEUP" + depends on CARL9170FW_WOL_PROBE_REQUEST + +config CARL9170FW_VIFS_NUM + default 1 + int + prompt "Number of additional pseudo virtual interfaces" + depends on CARL9170FW_EXPERIMENTAL + +config CARL9170FW_FW_MAC_RESET + def_bool y + prompt "Firmware MAC Chip recovery" + depends on CARL9170FW_EXPERIMENTAL + +config CARL9170FW_NOISY_MAC_RESET + def_bool n + prompt "Notify MAC RESET events" + depends on CARL9170FW_FW_MAC_RESET + +config CARL9170FW_BROKEN_FEATURES + def_bool n + prompt "Broken Featurs" + +config CARL9170FW_DEBUG + def_bool n + depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_PRINTF + prompt "Enable verbose debugging messages" + +config CARL9170FW_DEBUG_LED_HEARTBEAT + def_bool n + prompt "LED Heartbeat" + depends on CARL9170FW_BROKEN_FEATURES + ---help--- + This option conflicts with the application's LED code. + Also, it assumes that you have two LEDs, which is not + necessarily true. + +config CARL9170FW_DEBUG_UART + def_bool n + prompt "Pass debug messages through Highspeed UART" + depends on CARL9170FW_BROKEN_FEATURES + ---help--- + This option allows the firmware to send BUG/ERR/INFO/DBG and + hexdumps through the UART _as well_. However, first: you must + connect a working logger. + +config CARL9170FW_WATCHDOG_BUTTON + def_bool n + depends on CARL9170FW_BROKEN && CARL9170FW_GPIO_INTERRUPT + prompt "Trigger Watchdog by pressing the WPS button" + +choice CARL9170FW_UART_CLOCK + prompt "UART Clock" + depends on CARL9170FW_DEBUG_UART + default CARL9170FW_UART_CLOCK_40M + +config CARL9170FW_UART_CLOCK_25M + bool "25" + +config CARL9170FW_UART_CLOCK_40M + bool "40" + +endchoice + +config CARL9170FW_UNUSABLE + def_bool y + depends on CARL9170FW_BROKEN || CARL9170FW_DEBUG + +config CARL9170FW_USB_MODESWITCH + def_bool n + prompt "USB 1.1 / 2.0 switching support" + depends on CARL9170FW_BROKEN_FEATURES + ---help--- + Mostly implemented, but untested and some serious + doubts remain. + +config CARL9170FW_DMA_QUEUE_BUMP + def_bool n + prompt "Bump a stuck TX queue before doing a MAC reset" + depends on CARL9170FW_BROKEN_FEATURES + +menu "Build Options" +config CARL9170FW_AGGRESSIVE_CFLAGS + def_bool y + prompt "Enable aggressive size optimization" + ---help--- + This option adds several more optimization compiler flags, + which can greatly reduce the firmware size... at the expense + of machine-code readability. + + Say Y. Else the firmware might not fit onto the device! + +endmenu + +endmenu + +endmenu |