Adding upstream version 3.2.1+dfsg.upstream/3.2.1+dfsgupstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1153 insertions, 0 deletions

diff --git a/raddb/sites-available/default b/raddb/sites-available/default
new file mode 100644
index 0000000..dbad8e4
--- /dev/null
+++ b/raddb/sites-available/default
@@ -0,0 +1,1153 @@
+######################################################################
+#
+#	As of 2.0.0, FreeRADIUS supports virtual hosts using the
+#	"server" section, and configuration directives.
+#
+#	Virtual hosts should be put into the "sites-available"
+#	directory.  Soft links should be created in the "sites-enabled"
+#	directory to these files.  This is done in a normal installation.
+#
+#	If you are using 802.1X (EAP) authentication, please see also
+#	the "inner-tunnel" virtual server.  You will likely have to edit
+#	that, too, for authentication to work.
+#
+#	$Id$
+#
+######################################################################
+#
+#	Read "man radiusd" before editing this file.  See the section
+#	titled DEBUGGING.  It outlines a method where you can quickly
+#	obtain the configuration you want, without running into
+#	trouble.  See also "man unlang", which documents the format
+#	of this file.
+#
+#	This configuration is designed to work in the widest possible
+#	set of circumstances, with the widest possible number of
+#	authentication methods.  This means that in general, you should
+#	need to make very few changes to this file.
+#
+#	The best way to configure the server for your local system
+#	is to CAREFULLY edit this file.  Most attempts to make large
+#	edits to this file will BREAK THE SERVER.  Any edits should
+#	be small, and tested by running the server with "radiusd -X".
+#	Once the edits have been verified to work, save a copy of these
+#	configuration files somewhere.  (e.g. as a "tar" file).  Then,
+#	make more edits, and test, as above.
+#
+#	There are many "commented out" references to modules such
+#	as ldap, sql, etc.  These references serve as place-holders.
+#	If you need the functionality of that module, then configure
+#	it in radiusd.conf, and un-comment the references to it in
+#	this file.  In most cases, those small changes will result
+#	in the server being able to connect to the DB, and to
+#	authenticate users.
+#
+######################################################################
+
+server default {
+#
+#  If you want the server to listen on additional addresses, or on
+#  additional ports, you can use multiple "listen" sections.
+#
+#  Each section make the server listen for only one type of packet,
+#  therefore authentication and accounting have to be configured in
+#  different sections.
+#
+#  The server ignore all "listen" section if you are using '-i' and '-p'
+#  on the command line.
+#
+listen {
+	#  Type of packets to listen for.
+	#  Allowed values are:
+	#	auth	listen for authentication packets
+	#	acct	listen for accounting packets
+	#       auth+acct listen for both authentication and accounting packets
+	#	proxy   IP to use for sending proxied packets
+	#	detail  Read from the detail file.  For examples, see
+	#               raddb/sites-available/copy-acct-to-home-server
+	#	status  listen for Status-Server packets.  For examples,
+	#		see raddb/sites-available/status
+	#	coa     listen for CoA-Request and Disconnect-Request
+	#		packets.  For examples, see the file
+	#		raddb/sites-available/coa
+	#
+	type = auth
+
+	#  Note: "type = proxy" lets you control the source IP used for
+	#        proxying packets, with some limitations:
+	#
+	#    * A proxy listener CANNOT be used in a virtual server section.
+	#    * You should probably set "port = 0".
+	#    * Any "clients" configuration will be ignored.
+	#
+	#  See also proxy.conf, and the "src_ipaddr" configuration entry
+	#  in the sample "home_server" section.  When you specify the
+	#  source IP address for packets sent to a home server, the
+	#  proxy listeners are automatically created.
+
+	#  ipaddr/ipv4addr/ipv6addr - IP address on which to listen.
+	#  If multiple ones are listed, only the first one will
+	#  be used, and the others will be ignored.
+	#
+	#  The configuration options accept the following syntax:
+	#
+	#  ipv4addr - IPv4 address (e.g.192.0.2.3)
+	#  	    - wildcard (i.e. *)
+	#  	    - hostname (radius.example.com)
+	#  	      Only the A record for the host name is used.
+	#	      If there is no A record, an error is returned,
+	#	      and the server fails to start.
+	#
+	#  ipv6addr - IPv6 address (e.g. 2001:db8::1)
+	#  	    - wildcard (i.e. *)
+	#  	    - hostname (radius.example.com)
+	#  	      Only the AAAA record for the host name is used.
+	#	      If there is no AAAA record, an error is returned,
+	#	      and the server fails to start.
+	#
+	#  ipaddr   - IPv4 address as above
+	#  	    - IPv6 address as above
+	#  	    - wildcard (i.e. *), which means IPv4 wildcard.
+	#	    - hostname
+	#	      If there is only one A or AAAA record returned
+	#	      for the host name, it is used.
+	#	      If multiple A or AAAA records are returned
+	#	      for the host name, only the first one is used.
+	#	      If both A and AAAA records are returned
+	#	      for the host name, only the A record is used.
+	#
+	# ipv4addr = *
+	# ipv6addr = *
+	ipaddr = *
+
+	#  Port on which to listen.
+	#  Allowed values are:
+	#	integer port number (1812)
+	#	0 means "use /etc/services for the proper port"
+	port = 0
+
+	#  Some systems support binding to an interface, in addition
+	#  to the IP address.  This feature isn't strictly necessary,
+	#  but for sites with many IP addresses on one interface,
+	#  it's useful to say "listen on all addresses for eth0".
+	#
+	#  If your system does not support this feature, you will
+	#  get an error if you try to use it.
+	#
+#	interface = eth0
+
+	#  Per-socket lists of clients.  This is a very useful feature.
+	#
+	#  The name here is a reference to a section elsewhere in
+	#  radiusd.conf, or clients.conf.  Having the name as
+	#  a reference allows multiple sockets to use the same
+	#  set of clients.
+	#
+	#  If this configuration is used, then the global list of clients
+	#  is IGNORED for this "listen" section.  Take care configuring
+	#  this feature, to ensure you don't accidentally disable a
+	#  client you need.
+	#
+	#  See clients.conf for the configuration of "per_socket_clients".
+	#
+#	clients = per_socket_clients
+
+	#
+	#  Set the default UDP receive buffer size.  In most cases,
+	#  the default values set by the kernel are fine.  However, in
+	#  some cases the NASes will send large packets, and many of
+	#  them at a time.  It is then possible to overflow the
+	#  buffer, causing the kernel to drop packets before they
+	#  reach FreeRADIUS.  Increasing the size of the buffer will
+	#  avoid these packet drops.
+	#
+#	recv_buff = 65536
+
+	#
+	#  Connection limiting for sockets with "proto = tcp".
+	#
+	#  This section is ignored for other kinds of sockets.
+	#
+	limit {
+	      #
+	      #  Limit the number of simultaneous TCP connections to the socket
+	      #
+	      #  The default is 16.
+	      #  Setting this to 0 means "no limit"
+	      max_connections = 16
+
+	      #  The per-socket "max_requests" option does not exist.
+
+	      #
+	      #  The lifetime, in seconds, of a TCP connection.  After
+	      #  this lifetime, the connection will be closed.
+	      #
+	      #  Setting this to 0 means "forever".
+	      lifetime = 0
+
+	      #
+	      #  The idle timeout, in seconds, of a TCP connection.
+	      #  If no packets have been received over the connection for
+	      #  this time, the connection will be closed.
+	      #
+	      #  Setting this to 0 means "no timeout".
+	      #
+	      #  We STRONGLY RECOMMEND that you set an idle timeout.
+	      #
+	      idle_timeout = 30
+	}
+}
+
+#
+#  This second "listen" section is for listening on the accounting
+#  port, too.
+#
+listen {
+	ipaddr = *
+#	ipv6addr = ::
+	port = 0
+	type = acct
+#	interface = eth0
+#	clients = per_socket_clients
+
+	limit {
+		#  The number of packets received can be rate limited via the
+		#  "max_pps" configuration item.  When it is set, the server
+		#  tracks the total number of packets received in the previous
+		#  second.  If the count is greater than "max_pps", then the
+		#  new packet is silently discarded.  This helps the server
+		#  deal with overload situations.
+		#
+		#  The packets/s counter is tracked in a sliding window.  This
+		#  means that the pps calculation is done for the second
+		#  before the current packet was received.  NOT for the current
+		#  wall-clock second, and NOT for the previous wall-clock second.
+		#
+		#  Useful values are 0 (no limit), or 100 to 10000.
+		#  Values lower than 100 will likely cause the server to ignore
+		#  normal traffic.  Few systems are capable of handling more than
+		#  10K packets/s.
+		#
+		#  It is most useful for accounting systems.  Set it to 50%
+		#  more than the normal accounting load, and you can be sure that
+		#  the server will never get overloaded
+		#
+#		max_pps = 0
+
+		# Only for "proto = tcp". These are ignored for "udp" sockets.
+		#
+#		idle_timeout = 0
+#		lifetime = 0
+#		max_connections = 0
+	}
+}
+
+# IPv6 versions of the above - read their full config to understand options
+listen {
+	type = auth
+	ipv6addr = ::	# any.  ::1 == localhost
+	port = 0
+#	interface = eth0
+#	clients = per_socket_clients
+	limit {
+	      max_connections = 16
+	      lifetime = 0
+	      idle_timeout = 30
+	}
+}
+
+listen {
+	ipv6addr = ::
+	port = 0
+	type = acct
+#	interface = eth0
+#	clients = per_socket_clients
+
+	limit {
+#		max_pps = 0
+#		idle_timeout = 0
+#		lifetime = 0
+#		max_connections = 0
+	}
+}
+
+#  Authorization. First preprocess (hints and huntgroups files),
+#  then realms, and finally look in the "users" file.
+#
+#  Any changes made here should also be made to the "inner-tunnel"
+#  virtual server.
+#
+#  The order of the realm modules will determine the order that
+#  we try to find a matching realm.
+#
+#  Make *sure* that 'preprocess' comes before any realm if you
+#  need to setup hints for the remote radius server
+authorize {
+	#
+	#  Take a User-Name, and perform some checks on it, for spaces and other
+	#  invalid characters.  If the User-Name appears invalid, reject the
+	#  request.
+	#
+	#  See policy.d/filter for the definition of the filter_username policy.
+	#
+	filter_username
+
+	#
+	#  Some broken equipment sends passwords with embedded zeros.
+	#  i.e. the debug output will show
+	#
+	#	User-Password = "password\000\000"
+	#
+	#  This policy will fix it to just be "password".
+	#
+#	filter_password
+
+	#
+	#  The preprocess module takes care of sanitizing some bizarre
+	#  attributes in the request, and turning them into attributes
+	#  which are more standard.
+	#
+	#  It takes care of processing the 'raddb/mods-config/preprocess/hints' 
+	#  and the 'raddb/mods-config/preprocess/huntgroups' files.
+	preprocess
+
+	#  If you intend to use CUI and you require that the Operator-Name
+	#  be set for CUI generation and you want to generate CUI also
+	#  for your local clients then uncomment the operator-name
+	#  below and set the operator-name for your clients in clients.conf
+#	operator-name
+
+	#
+	#  If you want to generate CUI for some clients that do not
+	#  send proper CUI requests, then uncomment the
+	#  cui below and set "add_cui = yes" for these clients in clients.conf
+#	cui
+
+	#
+	#  If you want to have a log of authentication requests,
+	#  un-comment the following line.
+#	auth_log
+
+	#
+	#  The chap module will set 'Auth-Type := CHAP' if we are
+	#  handling a CHAP request and Auth-Type has not already been set
+	chap
+
+	#
+	#  If the users are logging in with an MS-CHAP-Challenge
+	#  attribute for authentication, the mschap module will find
+	#  the MS-CHAP-Challenge attribute, and add 'Auth-Type := MS-CHAP'
+	#  to the request, which will cause the server to then use
+	#  the mschap module for authentication.
+	mschap
+
+	#
+	#  If you have a Cisco SIP server authenticating against
+	#  FreeRADIUS, uncomment the following line, and the 'digest'
+	#  line in the 'authenticate' section.
+	digest
+
+	#
+	#  The WiMAX specification says that the Calling-Station-Id
+	#  is 6 octets of the MAC.  This definition conflicts with
+	#  RFC 3580, and all common RADIUS practices.  If you are using
+	#  old style WiMAX (non LTE) the un-commenting the "wimax" module
+	#  here means that it will fix the Calling-Station-Id attribute to
+	#  the normal format as specified in RFC 3580 Section 3.21.
+	#
+	#  If you are using WiMAX 2.1 (LTE) then un-commenting will allow 
+	#  the module to handle SQN resyncronisation. Prior to calling the
+	#  module it is necessary to populate the following attributes
+	#  with the relevant keys:
+	#    control:WiMAX-SIM-Ki
+	#    control:WiMAX-SIM-OPc
+	#
+	#  If WiMAX-Re-synchronization-Info is found in the request then
+	#  the module will attempt to extract SQN and store it in
+	#  control:WiMAX-SIM-SQN. Also a copy of RAND is extracted to
+	#  control:WiMAX-SIM-RAND.
+	#
+	#  If the SIM cannot be authenticated using Ki and OPc then reject
+	#  will be returned.
+#	wimax
+
+	#
+	#  Look for IPASS style 'realm/', and if not found, look for
+	#  '@realm', and decide whether or not to proxy, based on
+	#  that.
+#	IPASS
+
+	#
+	# Look for realms in user@domain format
+	suffix
+#	ntdomain
+
+	#
+	#  This module takes care of EAP-MD5, EAP-TLS, and EAP-LEAP
+	#  authentication.
+	#
+	#  It also sets the EAP-Type attribute in the request
+	#  attribute list to the EAP type from the packet.
+	#
+	#  The EAP module returns "ok" or "updated" if it is not yet ready
+	#  to authenticate the user.  The configuration below checks for
+	#  "ok", and stops processing the "authorize" section if so.
+	#
+	#  Any LDAP and/or SQL servers will not be queried for the
+	#  initial set of packets that go back and forth to set up
+	#  TTLS or PEAP.
+	#
+	#  The "updated" check is commented out for compatibility with
+	#  previous versions of this configuration, but you may wish to
+	#  uncomment it as well; this will further reduce the number of
+	#  LDAP and/or SQL queries for TTLS or PEAP.
+	#
+	eap {
+		ok = return
+#		updated = return
+	}
+
+	#
+	#  Pull crypt'd passwords from /etc/passwd or /etc/shadow,
+	#  using the system API's to get the password.  If you want
+	#  to read /etc/passwd or /etc/shadow directly, see the
+	#  mods-available/passwd module.
+	#
+#	unix
+
+	#
+	#  Read the 'users' file.  In v3, this is located in
+	#  raddb/mods-config/files/authorize
+	files
+
+	#
+	#  Look in an SQL database.  The schema of the database
+	#  is meant to mirror the "users" file.
+	#
+	#  See "Authorization Queries" in mods-available/sql
+	-sql
+
+	#
+	#  If you are using /etc/smbpasswd, and are also doing
+	#  mschap authentication, the un-comment this line, and
+	#  configure the 'smbpasswd' module.
+#	smbpasswd
+
+	#
+	#  The ldap module reads passwords from the LDAP database.
+	-ldap
+
+	#
+	#  If you're using Active Directory and PAP, then uncomment
+	#  the following lines, and the "Auth-Type LDAP" section below.
+	#
+	#  This will let you do PAP authentication to AD.
+	#
+#	if ((ok || updated) && User-Password && !control:Auth-Type) {
+#		update control {
+#			&Auth-Type := ldap
+#		}
+#	}
+
+	#
+	#  Enforce daily limits on time spent logged in.
+#	daily
+
+	#
+	expiration
+	logintime
+
+	#
+	#  If no other module has claimed responsibility for
+	#  authentication, then try to use PAP.  This allows the
+	#  other modules listed above to add a "known good" password
+	#  to the request, and to do nothing else.  The PAP module
+	#  will then see that password, and use it to do PAP
+	#  authentication.
+	#
+	#  This module should be listed last, so that the other modules
+	#  get a chance to set Auth-Type for themselves.
+	#
+	pap
+
+	#
+	#  If "status_server = yes", then Status-Server messages are passed
+	#  through the following section, and ONLY the following section.
+	#  This permits you to do DB queries, for example.  If the modules
+	#  listed here return "fail", then NO response is sent.
+	#
+#	Autz-Type Status-Server {
+#
+#	}
+
+	#
+	#  RADIUS/TLS (or RadSec) connections are processed through
+	#  this section.  See sites-available/tls, and the configuration
+	#  item "check_client_connections" for more information.
+	#
+	#  The request contains TLS client certificate attributes,
+	#  and nothing else.  The debug output will print which
+	#  attributes are available on your system.
+	#
+	#  If the section returns "ok" or "updated", then the
+	#  connection is accepted.  Otherwise the connection is
+	#  terminated.
+	#
+	Autz-Type New-TLS-Connection {
+		  ok
+	}
+}
+
+
+#  Authentication.
+#
+#
+#  This section lists which modules are available for authentication.
+#  Note that it does NOT mean 'try each module in order'.  It means
+#  that a module from the 'authorize' section adds a configuration
+#  attribute 'Auth-Type := FOO'.  That authentication type is then
+#  used to pick the appropriate module from the list below.
+#
+
+#  In general, you SHOULD NOT set the Auth-Type attribute.  The server
+#  will figure it out on its own, and will do the right thing.  The
+#  most common side effect of erroneously setting the Auth-Type
+#  attribute is that one authentication method will work, but the
+#  others will not.
+#
+#  The common reasons to set the Auth-Type attribute by hand
+#  is to either forcibly reject the user (Auth-Type := Reject),
+#  or to or forcibly accept the user (Auth-Type := Accept).
+#
+#  Note that Auth-Type := Accept will NOT work with EAP.
+#
+#  Please do not put "unlang" configurations into the "authenticate"
+#  section.  Put them in the "post-auth" section instead.  That's what
+#  the post-auth section is for.
+#
+authenticate {
+	#
+	#  PAP authentication, when a back-end database listed
+	#  in the 'authorize' section supplies a password.  The
+	#  password can be clear-text, or encrypted.
+	Auth-Type PAP {
+		pap
+	}
+
+	#
+	#  Most people want CHAP authentication
+	#  A back-end database listed in the 'authorize' section
+	#  MUST supply a CLEAR TEXT password.  Encrypted passwords
+	#  won't work.
+	Auth-Type CHAP {
+		chap
+	}
+
+	#
+	#  MSCHAP authentication.
+	Auth-Type MS-CHAP {
+		mschap
+	}
+
+	#
+	#  For old names, too.
+	#
+	mschap
+
+	#
+	#  If you have a Cisco SIP server authenticating against
+	#  FreeRADIUS, uncomment the following line, and the 'digest'
+	#  line in the 'authorize' section.
+	digest
+
+	#
+	#  Pluggable Authentication Modules.
+#	pam
+
+	#  Uncomment it if you want to use ldap for authentication
+	#
+	#  Note that this means "check plain-text password against
+	#  the ldap database", which means that EAP won't work,
+	#  as it does not supply a plain-text password.
+	#
+	#  We do NOT recommend using this.  LDAP servers are databases.
+	#  They are NOT authentication servers.  FreeRADIUS is an
+	#  authentication server, and knows what to do with authentication.
+	#  LDAP servers do not.
+	#
+	#  However, it is necessary for Active Directory, because
+	#  Active Directory won't give the passwords to FreeRADIUS.
+	#
+#	Auth-Type LDAP {
+#		ldap
+#	}
+
+	#
+	#  Allow EAP authentication.
+	eap
+
+	#
+	#  The older configurations sent a number of attributes in
+	#  Access-Challenge packets, which wasn't strictly correct.
+	#  If you want to filter out these attributes, uncomment
+	#  the following lines.
+	#
+#	Auth-Type eap {
+#		eap {
+#			handled = 1
+#		}
+#		if (handled && (Response-Packet-Type == Access-Challenge)) {
+#			attr_filter.access_challenge.post-auth
+#			handled  # override the "updated" code from attr_filter
+#		}
+#	}
+}
+
+
+#
+#  Pre-accounting.  Decide which accounting type to use.
+#
+preacct {
+	preprocess
+
+	#
+	#  Merge Acct-[Input|Output]-Gigawords and Acct-[Input-Output]-Octets
+	#  into a single 64bit counter Acct-[Input|Output]-Octets64.
+	#
+#	acct_counters64
+
+	#
+	#  Session start times are *implied* in RADIUS.
+	#  The NAS never sends a "start time".  Instead, it sends
+	#  a start packet, *possibly* with an Acct-Delay-Time.
+	#  The server is supposed to conclude that the start time
+	#  was "Acct-Delay-Time" seconds in the past.
+	#
+	#  The code below creates an explicit start time, which can
+	#  then be used in other modules.  It will be *mostly* correct.
+	#  Any errors are due to the 1-second resolution of RADIUS,
+	#  and the possibility that the time on the NAS may be off.
+	#
+	#  The start time is: NOW - delay - session_length
+	#
+
+#	update request {
+#	  	&FreeRADIUS-Acct-Session-Start-Time = "%{expr: %l - %{%{Acct-Session-Time}:-0} - %{%{Acct-Delay-Time}:-0}}"
+#	}
+
+
+	#
+	#  Ensure that we have a semi-unique identifier for every
+	#  request, and many NAS boxes are broken.
+	acct_unique
+
+	#
+	#  Look for IPASS-style 'realm/', and if not found, look for
+	#  '@realm', and decide whether or not to proxy, based on
+	#  that.
+	#
+	#  Accounting requests are generally proxied to the same
+	#  home server as authentication requests.
+#	IPASS
+	suffix
+#	ntdomain
+
+	#
+	#  Read the 'acct_users' file
+	files
+}
+
+#
+#  Accounting.  Log the accounting data.
+#
+accounting {
+	#  Update accounting packet by adding the CUI attribute
+	#  recorded from the corresponding Access-Accept
+	#  use it only if your NAS boxes do not support CUI themselves
+#	cui
+	#
+	#  Create a 'detail'ed log of the packets.
+	#  Note that accounting requests which are proxied
+	#  are also logged in the detail file.
+	detail
+#	daily
+
+	#  Update the wtmp file
+	#
+	#  If you don't use "radlast", you can delete this line.
+	unix
+
+	#
+	#  For Simultaneous-Use tracking.
+	#
+	#  Due to packet losses in the network, the data here
+	#  may be incorrect.  There is little we can do about it.
+#	radutmp
+#	sradutmp
+
+	#
+	#  Return an address to the IP Pool when we see a stop record.
+	#
+	#  Ensure that &control:Pool-Name is set to determine which
+	#  pool of IPs are used.
+#	sqlippool
+
+	#
+	#  Log traffic to an SQL database.
+	#
+	#  See "Accounting queries" in mods-available/sql
+	-sql
+
+	#
+	#  If you receive stop packets with zero session length,
+	#  they will NOT be logged in the database.  The SQL module
+	#  will print a message (only in debugging mode), and will
+	#  return "noop".
+	#
+	#  You can ignore these packets by uncommenting the following
+	#  three lines.  Otherwise, the server will not respond to the
+	#  accounting request, and the NAS will retransmit.
+	#
+#	if (noop) {
+#		ok
+#	}
+
+	#  Cisco VoIP specific bulk accounting
+#	pgsql-voip
+
+	# For Exec-Program and Exec-Program-Wait
+	exec
+
+	#  Filter attributes from the accounting response.
+	attr_filter.accounting_response
+
+	#
+	#  See "Autz-Type Status-Server" for how this works.
+	#
+#	Acct-Type Status-Server {
+#
+#	}
+}
+
+
+#  Session database, used for checking Simultaneous-Use. Either the radutmp
+#  or rlm_sql module can handle this.
+#  The rlm_sql module is *much* faster
+session {
+#	radutmp
+
+	#
+	#  See "Simultaneous Use Checking Queries" in mods-available/sql
+#	sql
+}
+
+
+#  Post-Authentication
+#  Once we KNOW that the user has been authenticated, there are
+#  additional steps we can take.
+post-auth {
+	#
+	#  If you need to have a State attribute, you can
+	#  add it here.  e.g. for later CoA-Request with
+	#  State, and Service-Type = Authorize-Only.
+	#
+#	if (!&reply:State) {
+#		update reply {
+#			State := "0x%{randstr:16h}"
+#		}
+#	}
+
+	#
+	#  Reject packets where User-Name != TLS-Client-Cert-Common-Name
+	#  There is no reason for users to lie about their names.
+	#
+	#  In general, User-Name == EAP Identity == TLS-Client-Cert-Common-Name
+	#
+#	verify_tls_client_common_name
+
+	#
+	#  If there is no Stripped-User-Name in the request, AND we have a client cert,
+	#  then create a Stripped-User-Name from the TLS client certificate information.
+	#
+	#  Note that this policy MUST be edited for your local system!
+	#  We do not know which fields exist in which certificate, as
+	#  there is no standard here.  There is no way for us to have
+	#  a default configuration which "just works" everywhere.  We
+	#  can only make recommendations.
+	#
+	#  The Stripped-User-Name is updated so that it is logged in
+	#  the various "username" fields.  This logging means that you
+	#  can associate a particular session with a particular client
+	#  certificate.
+	#
+#	if (&EAP-Message && !&Stripped-User-Name && &TLS-Client-Cert-Serial) {
+#		update request {
+#			&Stripped-User-Name := "%{%{TLS-Client-Cert-Subject-Alt-Name-Email}:-%{%{TLS-Client-Cert-Common-Name}:-%{TLS-Client-Cert-Serial}}}"
+#		}
+#
+		#
+		#  Create a Class attribute which is a hash of a bunch
+		#  of information which we hope exists.  This
+		#  attribute should be echoed back in
+		#  Accounting-Request packets, which will let the
+		#  administrator correlate authentication and
+		#  accounting.
+		#
+#		update reply {
+#			Class += "%{md5:%{Calling-Station-Id}%{Called-Station-Id}%{TLS-Client-Cert-Subject-Alt-Name-Email}%{TLS-Client-Cert-Common-Name}%{TLS-Client-Cert-Serial}%{NAS-IPv6-Address}%{NAS-IP-Address}%{NAS-Identifier}%{NAS-Port}"
+#		}
+#
+#	}
+
+	#
+	#  For EAP-TTLS and PEAP, add the cached attributes to the reply.
+	#  The "session-state" attributes are automatically cached when
+	#  an Access-Challenge is sent, and automatically retrieved
+	#  when an Access-Request is received.
+	#
+	#  The session-state attributes are automatically deleted after
+	#  an Access-Reject or Access-Accept is sent.
+	#
+	#  If both session-state and reply contain a User-Name attribute, remove
+	#  the one in the reply if it is just a copy of the one in the request, so
+	#  we don't end up with two User-Name attributes.
+
+	if (session-state:User-Name && reply:User-Name && request:User-Name && (reply:User-Name == request:User-Name)) {
+		update reply {
+			&User-Name !* ANY
+		}
+	}
+	update {
+		&reply: += &session-state:
+	}
+
+	#
+	#  Refresh leases when we see a start or alive. Return an address to
+	#  the IP Pool when we see a stop record.
+	#
+	#  Ensure that &control:Pool-Name is set to determine which
+	#  pool of IPs are used.
+#	sqlippool
+
+
+	#  Create the CUI value and add the attribute to Access-Accept.
+	#  Uncomment the line below if *returning* the CUI.
+#	cui
+
+	#  Create empty accounting session to make simultaneous check
+	#  more robust. See the accounting queries configuration in
+	#  raddb/mods-config/sql/main/*/queries.conf for details.
+	#
+	#  The "sql_session_start" policy is defined in
+	#  raddb/policy.d/accounting.  See that file for more details.
+#	sql_session_start
+
+	#
+	#  If you want to have a log of authentication replies,
+	#  un-comment the following line, and enable the
+	#  'detail reply_log' module.
+#	reply_log
+
+	#
+	#  After authenticating the user, do another SQL query.
+	#
+	#  See "Authentication Logging Queries" in mods-available/sql
+	-sql
+
+	#
+	#  Un-comment the following if you want to modify the user's object
+	#  in LDAP after a successful login.
+	#
+#	ldap
+
+	# For Exec-Program and Exec-Program-Wait
+	exec
+
+	#
+	#  In order to calcualate the various keys for old style WiMAX
+	#  (non LTE) you will need to define the WiMAX NAI, usually via
+	#
+	#	update request {
+	#	       &WiMAX-MN-NAI = "%{User-Name}"
+	#	}
+	#
+	#  If you want various keys to be calculated, you will need to
+	#  update the reply with "template" values.  The module will see
+	#  this, and replace the template values with the correct ones
+	#  taken from the cryptographic calculations.  e.g.
+	#
+	# 	update reply {
+	#		&WiMAX-FA-RK-Key = 0x00
+	#		&WiMAX-MSK = "%{reply:EAP-MSK}"
+	#	}
+	#
+	#  You may want to delete the MS-MPPE-*-Keys from the reply,
+	#  as some WiMAX clients behave badly when those attributes
+	#  are included.  See "raddb/modules/wimax", configuration
+	#  entry "delete_mppe_keys" for more information.
+	#
+	#  For LTE style WiMAX you need to populate the following with the
+	#  relevant values:
+	#    control:WiMAX-SIM-Ki
+	#    control:WiMAX-SIM-OPc
+	#    control:WiMAX-SIM-AMF
+	#    control:WiMAX-SIM-SQN
+	#
+#	wimax
+
+	#  If there is a client certificate (EAP-TLS, sometimes PEAP
+	#  and TTLS), then some attributes are filled out after the
+	#  certificate verification has been performed.  These fields
+	#  MAY be available during the authentication, or they may be
+	#  available only in the "post-auth" section.
+	#
+	#  The first set of attributes contains information about the
+	#  issuing certificate which is being used.  The second
+	#  contains information about the client certificate (if
+	#  available).
+#
+#	update reply {
+#	       Reply-Message += "%{TLS-Cert-Serial}"
+#	       Reply-Message += "%{TLS-Cert-Expiration}"
+#	       Reply-Message += "%{TLS-Cert-Subject}"
+#	       Reply-Message += "%{TLS-Cert-Issuer}"
+#	       Reply-Message += "%{TLS-Cert-Common-Name}"
+#	       Reply-Message += "%{TLS-Cert-Subject-Alt-Name-Email}"
+#
+#	       Reply-Message += "%{TLS-Client-Cert-Serial}"
+#	       Reply-Message += "%{TLS-Client-Cert-Expiration}"
+#	       Reply-Message += "%{TLS-Client-Cert-Subject}"
+#	       Reply-Message += "%{TLS-Client-Cert-Issuer}"
+#	       Reply-Message += "%{TLS-Client-Cert-Common-Name}"
+#	       Reply-Message += "%{TLS-Client-Cert-Subject-Alt-Name-Email}"
+#	}
+
+	#  Insert class attribute (with unique value) into response,
+	#  aids matching auth and acct records, and protects against duplicate
+	#  Acct-Session-Id. Note: Only works if the NAS has implemented
+	#  RFC 2865 behaviour for the class attribute, AND if the NAS
+	#  supports long Class attributes.  Many older or cheap NASes
+	#  only support 16-octet Class attributes.
+#	insert_acct_class
+
+	#  MacSEC requires the use of EAP-Key-Name.  However, we don't
+	#  want to send it for all EAP sessions.  Therefore, the EAP
+	#  modules put required data into the EAP-Session-Id attribute.
+	#  This attribute is never put into a request or reply packet.
+	#
+	#  Uncomment the next few lines to copy the required data into
+	#  the EAP-Key-Name attribute
+#	if (&reply:EAP-Session-Id) {
+#		update reply {
+#			EAP-Key-Name := &reply:EAP-Session-Id
+#		}
+#	}
+
+	#  Remove reply message if the response contains an EAP-Message
+	remove_reply_message_if_eap
+
+	#
+	#  Access-Reject packets are sent through the REJECT sub-section of the
+	#  post-auth section.
+	#
+	#  Add the ldap module name (or instance) if you have set
+	#  'edir = yes' in the ldap module configuration
+	#
+	#  The "session-state" attributes are not available here.
+	#
+	Post-Auth-Type REJECT {
+		# log failed authentications in SQL, too.
+		-sql
+		attr_filter.access_reject
+
+		# Insert EAP-Failure message if the request was
+		# rejected by policy instead of because of an
+		# authentication failure
+		eap
+
+		#  Remove reply message if the response contains an EAP-Message
+		remove_reply_message_if_eap
+	}
+
+	#
+	#  Filter access challenges.
+	#
+	Post-Auth-Type Challenge {
+#		remove_reply_message_if_eap
+#		attr_filter.access_challenge.post-auth
+	}
+
+	#
+	#  The Client-Lost section will be run for a request when
+	#  FreeRADIUS has given up waiting for an end-users client to
+	#  respond. This is most useful for logging EAP sessions where
+	#  the client stopped responding (likely because the
+	#  certificate was not acceptable.)  i.e. this is not for
+	#  RADIUS clients, but for end-user systems.
+	#
+	#  This will only be triggered by new packets arriving,
+	#  and will be run at some point in the future *after* the
+	#  original request has been discarded.
+	#
+	#  Therefore the *ONLY* attributes that are available here
+	#  are those in the session-state list. If you want data
+	#  to log, make sure it is copied to &session-state:
+	#  before the client stops responding. NONE of the other
+	#  original attributes (request, reply, etc) will be
+	#  available.
+	#
+	#  This section will only be run if `postauth_client_lost`
+	#  is enabled in the main configuration in `radiusd.conf`.
+	#
+	#  Note that there are MANY reasons why an end users system
+	#  might not respond:
+	#
+	#    * it could not get the packet due to firewall issues
+	#    * it could not get the packet due to a lossy network
+	#    * the users system might not like the servers cert
+	#    * the users system might not like something else...
+	#
+	#  In some cases, the client is helpful enough to send us a
+	#  TLS Alert message, saying what it doesn't like about the
+	#  certificate.  In other cases, no such message is available.
+	#
+	#  All that we can know on the FreeRADIUS side is that we sent
+	#  an Access-Challenge, and the client never sent anything
+	#  else.  The reasons WHY this happens are buried inside of
+	#  the logs on the client system.  No amount of looking at the
+	#  FreeRADIUS logs, or poking the FreeRADIUS configuration
+	#  will tell you why the client gave up.  The answers are in
+	#  the logs on the client side.  And no, the FreeRADIUS team
+	#  didn't write the client, so we don't know where those logs
+	#  are, or how to get at them.
+	#
+	#  Information about the TLS state changes is in the
+	#  &session-state:TLS-Session-Information attribute.
+	#
+	Post-Auth-Type Client-Lost {
+		#
+		#  Debug ALL of the TLS state changes done during the
+		#  EAP negotiation.
+		#
+#		%{debug_attr:&session-state:TLS-Session-Information[*]}
+
+		#
+		#  Debug the LAST TLS state change done during the EAP
+		#  negotiation.  For errors, this is usually a TLS
+		#  alert from the client saying something like
+		#  "unknown CA".
+		#
+#		%{debug_attr:&session-state:TLS-Session-Information[n]}
+
+		#
+		#  Debug the last module failure message.  This may be
+		#  useful, or it may refer to a server-side failure
+		#  which did not cause the client to stop talking to the server.
+		#
+#		%{debug_attr:&session-state:Module-Failure-Message}
+	}
+
+	#
+	#  If the client sends EAP-Key-Name in the request,
+	#  then echo the real value back in the reply.
+	#
+	if (EAP-Key-Name && &reply:EAP-Session-Id) {
+		update reply {
+			&EAP-Key-Name := &reply:EAP-Session-Id
+		}
+	}
+}
+
+#
+#  When the server decides to proxy a request to a home server,
+#  the proxied request is first passed through the pre-proxy
+#  stage.  This stage can re-write the request, or decide to
+#  cancel the proxy.
+#
+#  Only a few modules currently have this method.
+#
+pre-proxy {
+	# Before proxing the request add an Operator-Name attribute identifying
+	# if the operator-name is found for this client.
+	# No need to uncomment this if you have already enabled this in
+	# the authorize section.
+#	operator-name
+
+	#  The client requests the CUI by sending a CUI attribute
+	#  containing one zero byte.
+	#  Uncomment the line below if *requesting* the CUI.
+#	cui
+
+	#  Uncomment the following line if you want to change attributes
+	#  as defined in the preproxy_users file.
+#	files
+
+	#  Uncomment the following line if you want to filter requests
+	#  sent to remote servers based on the rules defined in the
+	#  'attrs.pre-proxy' file.
+#	attr_filter.pre-proxy
+
+	#  If you want to have a log of packets proxied to a home
+	#  server, un-comment the following line, and the
+	#  'detail pre_proxy_log' section, above.
+#	pre_proxy_log
+}
+
+#
+#  When the server receives a reply to a request it proxied
+#  to a home server, the request may be massaged here, in the
+#  post-proxy stage.
+#
+post-proxy {
+
+	#  If you want to have a log of replies from a home server,
+	#  un-comment the following line, and the 'detail post_proxy_log'
+	#  section, above.
+#	post_proxy_log
+
+	#  Uncomment the following line if you want to filter replies from
+	#  remote proxies based on the rules defined in the 'attrs' file.
+#	attr_filter.post-proxy
+
+	#
+	#  If you are proxying LEAP, you MUST configure the EAP
+	#  module, and you MUST list it here, in the post-proxy
+	#  stage.
+	#
+	#  You MUST also use the 'nostrip' option in the 'realm'
+	#  configuration.  Otherwise, the User-Name attribute
+	#  in the proxied request will not match the user name
+	#  hidden inside of the EAP packet, and the end server will
+	#  reject the EAP request.
+	#
+	eap
+
+	#
+	#  If the server tries to proxy a request and fails, then the
+	#  request is processed through the modules in this section.
+	#
+	#  The main use of this section is to permit robust proxying
+	#  of accounting packets.  The server can be configured to
+	#  proxy accounting packets as part of normal processing.
+	#  Then, if the home server goes down, accounting packets can
+	#  be logged to a local "detail" file, for processing with
+	#  radrelay.  When the home server comes back up, radrelay
+	#  will read the detail file, and send the packets to the
+	#  home server.
+	#
+	#  See the "mods-available/detail.example.com" file for more
+	#  details on writing a detail file specifically for one
+	#  destination.
+	#
+	#  See the "sites-available/robust-proxy-accounting" virtual
+	#  server for more details on reading this "detail" file.
+	#
+	#  With this configuration, the server always responds to
+	#  Accounting-Requests from the NAS, but only writes
+	#  accounting packets to disk if the home server is down.
+	#
+#	Post-Proxy-Type Fail-Accounting {
+#			detail.example.com
+#	}
+}
+}