From da76459dc21b5af2449af2d36eb95226cb186ce2 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sun, 28 Apr 2024 11:35:11 +0200 Subject: Adding upstream version 2.6.12. Signed-off-by: Daniel Baumann --- doc/management.txt | 4203 ++++++++++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 4203 insertions(+) create mode 100644 doc/management.txt (limited to 'doc/management.txt') diff --git a/doc/management.txt b/doc/management.txt new file mode 100644 index 0000000..dfbcca2 --- /dev/null +++ b/doc/management.txt @@ -0,0 +1,4203 @@ + ------------------------ + HAProxy Management Guide + ------------------------ + version 2.6 + + +This document describes how to start, stop, manage, and troubleshoot HAProxy, +as well as some known limitations and traps to avoid. It does not describe how +to configure it (for this please read configuration.txt). + +Note to documentation contributors : + This document is formatted with 80 columns per line, with even number of + spaces for indentation and without tabs. Please follow these rules strictly + so that it remains easily printable everywhere. If you add sections, please + update the summary below for easier searching. + + +Summary +------- + +1. Prerequisites +2. Quick reminder about HAProxy's architecture +3. Starting HAProxy +4. Stopping and restarting HAProxy +5. File-descriptor limitations +6. Memory management +7. CPU usage +8. Logging +9. Statistics and monitoring +9.1. CSV format +9.2. Typed output format +9.3. Unix Socket commands +9.4. Master CLI +9.4.1. Master CLI commands +10. Tricks for easier configuration management +11. Well-known traps to avoid +12. Debugging and performance issues +13. Security considerations + + +1. Prerequisites +---------------- + +In this document it is assumed that the reader has sufficient administration +skills on a UNIX-like operating system, uses the shell on a daily basis and is +familiar with troubleshooting utilities such as strace and tcpdump. + + +2. Quick reminder about HAProxy's architecture +---------------------------------------------- + +HAProxy is a multi-threaded, event-driven, non-blocking daemon. This means is +uses event multiplexing to schedule all of its activities instead of relying on +the system to schedule between multiple activities. Most of the time it runs as +a single process, so the output of "ps aux" on a system will report only one +"haproxy" process, unless a soft reload is in progress and an older process is +finishing its job in parallel to the new one. It is thus always easy to trace +its activity using the strace utility. In order to scale with the number of +available processors, by default haproxy will start one worker thread per +processor it is allowed to run on. Unless explicitly configured differently, +the incoming traffic is spread over all these threads, all running the same +event loop. A great care is taken to limit inter-thread dependencies to the +strict minimum, so as to try to achieve near-linear scalability. This has some +impacts such as the fact that a given connection is served by a single thread. +Thus in order to use all available processing capacity, it is needed to have at +least as many connections as there are threads, which is almost always granted. + +HAProxy is designed to isolate itself into a chroot jail during startup, where +it cannot perform any file-system access at all. This is also true for the +libraries it depends on (eg: libc, libssl, etc). The immediate effect is that +a running process will not be able to reload a configuration file to apply +changes, instead a new process will be started using the updated configuration +file. Some other less obvious effects are that some timezone files or resolver +files the libc might attempt to access at run time will not be found, though +this should generally not happen as they're not needed after startup. A nice +consequence of this principle is that the HAProxy process is totally stateless, +and no cleanup is needed after it's killed, so any killing method that works +will do the right thing. + +HAProxy doesn't write log files, but it relies on the standard syslog protocol +to send logs to a remote server (which is often located on the same system). + +HAProxy uses its internal clock to enforce timeouts, that is derived from the +system's time but where unexpected drift is corrected. This is done by limiting +the time spent waiting in poll() for an event, and measuring the time it really +took. In practice it never waits more than one second. This explains why, when +running strace over a completely idle process, periodic calls to poll() (or any +of its variants) surrounded by two gettimeofday() calls are noticed. They are +normal, completely harmless and so cheap that the load they imply is totally +undetectable at the system scale, so there's nothing abnormal there. Example : + + 16:35:40.002320 gettimeofday({1442759740, 2605}, NULL) = 0 + 16:35:40.002942 epoll_wait(0, {}, 200, 1000) = 0 + 16:35:41.007542 gettimeofday({1442759741, 7641}, NULL) = 0 + 16:35:41.007998 gettimeofday({1442759741, 8114}, NULL) = 0 + 16:35:41.008391 epoll_wait(0, {}, 200, 1000) = 0 + 16:35:42.011313 gettimeofday({1442759742, 11411}, NULL) = 0 + +HAProxy is a TCP proxy, not a router. It deals with established connections that +have been validated by the kernel, and not with packets of any form nor with +sockets in other states (eg: no SYN_RECV nor TIME_WAIT), though their existence +may prevent it from binding a port. It relies on the system to accept incoming +connections and to initiate outgoing connections. An immediate effect of this is +that there is no relation between packets observed on the two sides of a +forwarded connection, which can be of different size, numbers and even family. +Since a connection may only be accepted from a socket in LISTEN state, all the +sockets it is listening to are necessarily visible using the "netstat" utility +to show listening sockets. Example : + + # netstat -ltnp + Active Internet connections (only servers) + Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name + tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1629/sshd + tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN 2847/haproxy + tcp 0 0 0.0.0.0:443 0.0.0.0:* LISTEN 2847/haproxy + + +3. Starting HAProxy +------------------- + +HAProxy is started by invoking the "haproxy" program with a number of arguments +passed on the command line. The actual syntax is : + + $ haproxy []* + +where []* is any number of options. An option always starts with '-' +followed by one of more letters, and possibly followed by one or multiple extra +arguments. Without any option, HAProxy displays the help page with a reminder +about supported options. Available options may vary slightly based on the +operating system. A fair number of these options overlap with an equivalent one +if the "global" section. In this case, the command line always has precedence +over the configuration file, so that the command line can be used to quickly +enforce some settings without touching the configuration files. The current +list of options is : + + -- * : all the arguments following "--" are paths to configuration + file/directory to be loaded and processed in the declaration order. It is + mostly useful when relying on the shell to load many files that are + numerically ordered. See also "-f". The difference between "--" and "-f" is + that one "-f" must be placed before each file name, while a single "--" is + needed before all file names. Both options can be used together, the + command line ordering still applies. When more than one file is specified, + each file must start on a section boundary, so the first keyword of each + file must be one of "global", "defaults", "peers", "listen", "frontend", + "backend", and so on. A file cannot contain just a server list for example. + + -f : adds to the list of configuration files to be + loaded. If is a directory, all the files (and only files) it + contains are added in lexical order (using LC_COLLATE=C) to the list of + configuration files to be loaded ; only files with ".cfg" extension are + added, only non hidden files (not prefixed with ".") are added. + Configuration files are loaded and processed in their declaration order. + This option may be specified multiple times to load multiple files. See + also "--". The difference between "--" and "-f" is that one "-f" must be + placed before each file name, while a single "--" is needed before all file + names. Both options can be used together, the command line ordering still + applies. When more than one file is specified, each file must start on a + section boundary, so the first keyword of each file must be one of + "global", "defaults", "peers", "listen", "frontend", "backend", and so on. + A file cannot contain just a server list for example. + + -C : changes to directory before loading configuration + files. This is useful when using relative paths. Warning when using + wildcards after "--" which are in fact replaced by the shell before + starting haproxy. + + -D : start as a daemon. The process detaches from the current terminal after + forking, and errors are not reported anymore in the terminal. It is + equivalent to the "daemon" keyword in the "global" section of the + configuration. It is recommended to always force it in any init script so + that a faulty configuration doesn't prevent the system from booting. + + -L : change the local peer name to , which defaults to the local + hostname. This is used only with peers replication. You can use the + variable $HAPROXY_LOCALPEER in the configuration file to reference the + peer name. + + -N : sets the default per-proxy maxconn to instead of the + builtin default value (usually 2000). Only useful for debugging. + + -V : enable verbose mode (disables quiet mode). Reverts the effect of "-q" or + "quiet". + + -W : master-worker mode. It is equivalent to the "master-worker" keyword in + the "global" section of the configuration. This mode will launch a "master" + which will monitor the "workers". Using this mode, you can reload HAProxy + directly by sending a SIGUSR2 signal to the master. The master-worker mode + is compatible either with the foreground or daemon mode. It is + recommended to use this mode with multiprocess and systemd. + + -Ws : master-worker mode with support of `notify` type of systemd service. + This option is only available when HAProxy was built with `USE_SYSTEMD` + build option enabled. + + -c : only performs a check of the configuration files and exits before trying + to bind. The exit status is zero if everything is OK, or non-zero if an + error is encountered. Presence of warnings will be reported if any. + + -cc : evaluates a condition as used within a conditional block of the + configuration. The exit status is zero if the condition is true, 1 if the + condition is false or 2 if an error is encountered. + + -d : enable debug mode. This disables daemon mode, forces the process to stay + in foreground and to show incoming and outgoing events. It must never be + used in an init script. + + -dD : enable diagnostic mode. This mode will output extra warnings about + suspicious configuration statements. This will never prevent startup even in + "zero-warning" mode nor change the exit status code. + + -dG : disable use of getaddrinfo() to resolve host names into addresses. It + can be used when suspecting that getaddrinfo() doesn't work as expected. + This option was made available because many bogus implementations of + getaddrinfo() exist on various systems and cause anomalies that are + difficult to troubleshoot. + + -dK : dumps the list of registered keywords in each class. + The list of classes is available with "-dKhelp". All classes may be dumped + using "-dKall", otherwise a selection of those shown in the help can be + specified as a comma-delimited list. The output format will vary depending + on what class of keywords is being dumped (e.g. "cfg" will show the known + configuration keywords in a format resembling the config file format while + "smp" will show sample fetch functions prefixed with a compatibility matrix + with each rule set). These may rarely be used as-is by humans but can be of + great help for external tools that try to detect the appearance of new + keywords at certain places to automatically update some documentation, + syntax highlighting files, configuration parsers, API etc. The output + format may evolve a bit over time so it is really recommended to use this + output mostly to detect differences with previous archives. Note that not + all keywords are listed because many keywords have existed long before the + different keyword registration subsystems were created, and they do not + appear there. However since new keywords are only added via the modern + mechanisms, it's reasonably safe to assume that this output may be used to + detect language additions with a good accuracy. The keywords are only + dumped after the configuration is fully parsed, so that even dynamically + created keywords can be dumped. A good way to dump and exit is to run a + silent config check on an existing configuration: + + ./haproxy -dKall -q -c -f foo.cfg + + If no configuration file is available, using "-f /dev/null" will work as + well to dump all default keywords, but then the return status will not be + zero since there will be no listener, and will have to be ignored. + + -dL : dumps the list of dynamic shared libraries that are loaded at the end + of the config processing. This will generally also include deep dependencies + such as anything loaded from Lua code for example, as well as the executable + itself. The list is printed in a format that ought to be easy enough to + sanitize to directly produce a tarball of all dependencies. Since it doesn't + stop the program's startup, it is recommended to only use it in combination + with "-c" and "-q" where only the list of loaded objects will be displayed + (or nothing in case of error). In addition, keep in mind that when providing + such a package to help with a core file analysis, most libraries are in fact + symbolic links that need to be dereferenced when creating the archive: + + ./haproxy -W -q -c -dL -f foo.cfg | tar -T - -hzcf archive.tgz + + -dM[[,]][help|options,...] : forces memory poisoning, and/or changes + memory other debugging options. Memory poisonning means that each and every + memory region allocated with malloc() or pool_alloc() will be filled with + before being passed to the caller. When is not specified, it + defaults to 0x50 ('P'). While this slightly slows down operations, it is + useful to reliably trigger issues resulting from missing initializations in + the code that cause random crashes. Note that -dM0 has the effect of + turning any malloc() into a calloc(). In any case if a bug appears or + disappears when using this option it means there is a bug in haproxy, so + please report it. A number of other options are available either alone or + after a comma following the byte. The special option "help" will list the + currently supported options and their current value. Each debugging option + may be forced on or off. The most optimal options are usually chosen at + build time based on the operating system and do not need to be adjusted, + unless suggested by a developer. Supported debugging options include + (set/clear): + - fail / no-fail: + This enables randomly failing memory allocations, in conjunction with + the global "tune.fail-alloc" setting. This is used to detect missing + error checks in the code. + + - no-merge / merge: + By default, pools of very similar sizes are merged, resulting in more + efficiency, but this complicates the analysis of certain memory dumps. + This option allows to disable this mechanism, and may slightly increase + the memory usage. + + - cold-first / hot-first: + In order to optimize the CPU cache hit ratio, by default the most + recently released objects ("hot") are recycled for new allocations. + But doing so also complicates analysis of memory dumps and may hide + use-after-free bugs. This option allows to instead pick the coldest + objects first, which may result in a slight increase of CPU usage. + + - integrity / no-integrity: + When this option is enabled, memory integrity checks are enabled on + the allocated area to verify that it hasn't been modified since it was + last released. This works best with "no-merge", "cold-first" and "tag". + Enabling this option will slightly increase the CPU usage. + + - no-global / global: + Depending on the operating system, a process-wide global memory cache + may be enabled if it is estimated that the standard allocator is too + slow or inefficient with threads. This option allows to forcefully + disable it or enable it. Disabling it may result in a CPU usage + increase with inefficient allocators. Enabling it may result in a + higher memory usage with efficient allocators. + + - no-cache / cache: + Each thread uses a very fast local object cache for allocations, which + is always enabled by default. This option allows to disable it. Since + the global cache also passes via the local caches, this will + effectively result in disabling all caches and allocating directly from + the default allocator. This may result in a significant increase of CPU + usage, but may also result in small memory savings on tiny systems. + + - caller / no-caller: + Enabling this option reserves some extra space in each allocated object + to store the address of the last caller that allocated or released it. + This helps developers go back in time when analysing memory dumps and + to guess how something unexpected happened. + + - tag / no-tag: + Enabling this option reserves some extra space in each allocated object + to store a tag that allows to detect bugs such as double-free, freeing + an invalid object, and buffer overflows. It offers much stronger + reliability guarantees at the expense of 4 or 8 extra bytes per + allocation. It usually is the first step to detect memory corruption. + + - poison / no-poison: + Enabling this option will fill allocated objects with a fixed pattern + that will make sure that some accidental values such as 0 will not be + present if a newly added field was mistakenly forgotten in an + initialization routine. Such bugs tend to rarely reproduce, especially + when pools are not merged. This is normally enabled by directly passing + the byte's value to -dM but using this option allows to disable/enable + use of a previously set value. + + -dS : disable use of the splice() system call. It is equivalent to the + "global" section's "nosplice" keyword. This may be used when splice() is + suspected to behave improperly or to cause performance issues, or when + using strace to see the forwarded data (which do not appear when using + splice()). + + -dV : disable SSL verify on the server side. It is equivalent to having + "ssl-server-verify none" in the "global" section. This is useful when + trying to reproduce production issues out of the production + environment. Never use this in an init script as it degrades SSL security + to the servers. + + -dW : if set, haproxy will refuse to start if any warning was emitted while + processing the configuration. This helps detect subtle mistakes and keep the + configuration clean and portable across versions. It is recommended to set + this option in service scripts when configurations are managed by humans, + but it is recommended not to use it with generated configurations, which + tend to emit more warnings. It may be combined with "-c" to cause warnings + in checked configurations to fail. This is equivalent to global option + "zero-warning". + + -db : disable background mode and multi-process mode. The process remains in + foreground. It is mainly used during development or during small tests, as + Ctrl-C is enough to stop the process. Never use it in an init script. + + -de : disable the use of the "epoll" poller. It is equivalent to the "global" + section's keyword "noepoll". It is mostly useful when suspecting a bug + related to this poller. On systems supporting epoll, the fallback will + generally be the "poll" poller. + + -dk : disable the use of the "kqueue" poller. It is equivalent to the + "global" section's keyword "nokqueue". It is mostly useful when suspecting + a bug related to this poller. On systems supporting kqueue, the fallback + will generally be the "poll" poller. + + -dp : disable the use of the "poll" poller. It is equivalent to the "global" + section's keyword "nopoll". It is mostly useful when suspecting a bug + related to this poller. On systems supporting poll, the fallback will + generally be the "select" poller, which cannot be disabled and is limited + to 1024 file descriptors. + + -dr : ignore server address resolution failures. It is very common when + validating a configuration out of production not to have access to the same + resolvers and to fail on server address resolution, making it difficult to + test a configuration. This option simply appends the "none" method to the + list of address resolution methods for all servers, ensuring that even if + the libc fails to resolve an address, the startup sequence is not + interrupted. + + -m : limit the total allocatable memory to megabytes across + all processes. This may cause some connection refusals or some slowdowns + depending on the amount of memory needed for normal operations. This is + mostly used to force the processes to work in a constrained resource usage + scenario. It is important to note that the memory is not shared between + processes, so in a multi-process scenario, this value is first divided by + global.nbproc before forking. + + -n : limits the per-process connection limit to . This is + equivalent to the global section's keyword "maxconn". It has precedence + over this keyword. This may be used to quickly force lower limits to avoid + a service outage on systems where resource limits are too low. + + -p : write all processes' pids into during startup. This is + equivalent to the "global" section's keyword "pidfile". The file is opened + before entering the chroot jail, and after doing the chdir() implied by + "-C". Each pid appears on its own line. + + -q : set "quiet" mode. This disables some messages during the configuration + parsing and during startup. It can be used in combination with "-c" to + just check if a configuration file is valid or not. + + -S [,bind_options...]: in master-worker mode, bind a master CLI, which + allows the access to every processes, running or leaving ones. + For security reasons, it is recommended to bind the master CLI to a local + UNIX socket. The bind options are the same as the keyword "bind" in + the configuration file with words separated by commas instead of spaces. + + Note that this socket can't be used to retrieve the listening sockets from + an old process during a seamless reload. + + -sf * : send the "finish" signal (SIGUSR1) to older processes after boot + completion to ask them to finish what they are doing and to leave. + is a list of pids to signal (one per argument). The list ends on any + option starting with a "-". It is not a problem if the list of pids is + empty, so that it can be built on the fly based on the result of a command + like "pidof" or "pgrep". QUIC connections will be aborted. + + -st * : send the "terminate" signal (SIGTERM) to older processes after + boot completion to terminate them immediately without finishing what they + were doing. is a list of pids to signal (one per argument). The list + is ends on any option starting with a "-". It is not a problem if the list + of pids is empty, so that it can be built on the fly based on the result of + a command like "pidof" or "pgrep". + + -v : report the version and build date. + + -vv : display the version, build options, libraries versions and usable + pollers. This output is systematically requested when filing a bug report. + + -x : connect to the specified socket and try to retrieve any + listening sockets from the old process, and use them instead of trying to + bind new ones. This is useful to avoid missing any new connection when + reloading the configuration on Linux. The capability must be enable on the + stats socket using "expose-fd listeners" in your configuration. + In master-worker mode, the master will use this option upon a reload with + the "sockpair@" syntax, which allows the master to connect directly to a + worker without using stats socket declared in the configuration. + +A safe way to start HAProxy from an init file consists in forcing the daemon +mode, storing existing pids to a pid file and using this pid file to notify +older processes to finish before leaving : + + haproxy -f /etc/haproxy.cfg \ + -D -p /var/run/haproxy.pid -sf $(cat /var/run/haproxy.pid) + +When the configuration is split into a few specific files (eg: tcp vs http), +it is recommended to use the "-f" option : + + haproxy -f /etc/haproxy/global.cfg -f /etc/haproxy/stats.cfg \ + -f /etc/haproxy/default-tcp.cfg -f /etc/haproxy/tcp.cfg \ + -f /etc/haproxy/default-http.cfg -f /etc/haproxy/http.cfg \ + -D -p /var/run/haproxy.pid -sf $(cat /var/run/haproxy.pid) + +When an unknown number of files is expected, such as customer-specific files, +it is recommended to assign them a name starting with a fixed-size sequence +number and to use "--" to load them, possibly after loading some defaults : + + haproxy -f /etc/haproxy/global.cfg -f /etc/haproxy/stats.cfg \ + -f /etc/haproxy/default-tcp.cfg -f /etc/haproxy/tcp.cfg \ + -f /etc/haproxy/default-http.cfg -f /etc/haproxy/http.cfg \ + -D -p /var/run/haproxy.pid -sf $(cat /var/run/haproxy.pid) \ + -f /etc/haproxy/default-customers.cfg -- /etc/haproxy/customers/* + +Sometimes a failure to start may happen for whatever reason. Then it is +important to verify if the version of HAProxy you are invoking is the expected +version and if it supports the features you are expecting (eg: SSL, PCRE, +compression, Lua, etc). This can be verified using "haproxy -vv". Some +important information such as certain build options, the target system and +the versions of the libraries being used are reported there. It is also what +you will systematically be asked for when posting a bug report : + + $ haproxy -vv + HAProxy version 1.6-dev7-a088d3-4 2015/10/08 + Copyright 2000-2015 Willy Tarreau + + Build options : + TARGET = linux2628 + CPU = generic + CC = gcc + CFLAGS = -pg -O0 -g -fno-strict-aliasing -Wdeclaration-after-statement \ + -DBUFSIZE=8030 -DMAXREWRITE=1030 -DSO_MARK=36 -DTCP_REPAIR=19 + OPTIONS = USE_ZLIB=1 USE_DLMALLOC=1 USE_OPENSSL=1 USE_LUA=1 USE_PCRE=1 + + Default settings : + maxconn = 2000, bufsize = 8030, maxrewrite = 1030, maxpollevents = 200 + + Encrypted password support via crypt(3): yes + Built with zlib version : 1.2.6 + Compression algorithms supported : identity("identity"), deflate("deflate"), \ + raw-deflate("deflate"), gzip("gzip") + Built with OpenSSL version : OpenSSL 1.0.1o 12 Jun 2015 + Running on OpenSSL version : OpenSSL 1.0.1o 12 Jun 2015 + OpenSSL library supports TLS extensions : yes + OpenSSL library supports SNI : yes + OpenSSL library supports prefer-server-ciphers : yes + Built with PCRE version : 8.12 2011-01-15 + PCRE library supports JIT : no (USE_PCRE_JIT not set) + Built with Lua version : Lua 5.3.1 + Built with transparent proxy support using: IP_TRANSPARENT IP_FREEBIND + + Available polling systems : + epoll : pref=300, test result OK + poll : pref=200, test result OK + select : pref=150, test result OK + Total: 3 (3 usable), will use epoll. + +The relevant information that many non-developer users can verify here are : + - the version : 1.6-dev7-a088d3-4 above means the code is currently at commit + ID "a088d3" which is the 4th one after after official version "1.6-dev7". + Version 1.6-dev7 would show as "1.6-dev7-8c1ad7". What matters here is in + fact "1.6-dev7". This is the 7th development version of what will become + version 1.6 in the future. A development version not suitable for use in + production (unless you know exactly what you are doing). A stable version + will show as a 3-numbers version, such as "1.5.14-16f863", indicating the + 14th level of fix on top of version 1.5. This is a production-ready version. + + - the release date : 2015/10/08. It is represented in the universal + year/month/day format. Here this means August 8th, 2015. Given that stable + releases are issued every few months (1-2 months at the beginning, sometimes + 6 months once the product becomes very stable), if you're seeing an old date + here, it means you're probably affected by a number of bugs or security + issues that have since been fixed and that it might be worth checking on the + official site. + + - build options : they are relevant to people who build their packages + themselves, they can explain why things are not behaving as expected. For + example the development version above was built for Linux 2.6.28 or later, + targeting a generic CPU (no CPU-specific optimizations), and lacks any + code optimization (-O0) so it will perform poorly in terms of performance. + + - libraries versions : zlib version is reported as found in the library + itself. In general zlib is considered a very stable product and upgrades + are almost never needed. OpenSSL reports two versions, the version used at + build time and the one being used, as found on the system. These ones may + differ by the last letter but never by the numbers. The build date is also + reported because most OpenSSL bugs are security issues and need to be taken + seriously, so this library absolutely needs to be kept up to date. Seeing a + 4-months old version here is highly suspicious and indeed an update was + missed. PCRE provides very fast regular expressions and is highly + recommended. Certain of its extensions such as JIT are not present in all + versions and still young so some people prefer not to build with them, + which is why the build status is reported as well. Regarding the Lua + scripting language, HAProxy expects version 5.3 which is very young since + it was released a little time before HAProxy 1.6. It is important to check + on the Lua web site if some fixes are proposed for this branch. + + - Available polling systems will affect the process's scalability when + dealing with more than about one thousand of concurrent connections. These + ones are only available when the correct system was indicated in the TARGET + variable during the build. The "epoll" mechanism is highly recommended on + Linux, and the kqueue mechanism is highly recommended on BSD. Lacking them + will result in poll() or even select() being used, causing a high CPU usage + when dealing with a lot of connections. + + +4. Stopping and restarting HAProxy +---------------------------------- + +HAProxy supports a graceful and a hard stop. The hard stop is simple, when the +SIGTERM signal is sent to the haproxy process, it immediately quits and all +established connections are closed. The graceful stop is triggered when the +SIGUSR1 signal is sent to the haproxy process. It consists in only unbinding +from listening ports, but continue to process existing connections until they +close. Once the last connection is closed, the process leaves. + +The hard stop method is used for the "stop" or "restart" actions of the service +management script. The graceful stop is used for the "reload" action which +tries to seamlessly reload a new configuration in a new process. + +Both of these signals may be sent by the new haproxy process itself during a +reload or restart, so that they are sent at the latest possible moment and only +if absolutely required. This is what is performed by the "-st" (hard) and "-sf" +(graceful) options respectively. + +In master-worker mode, it is not needed to start a new haproxy process in +order to reload the configuration. The master process reacts to the SIGUSR2 +signal by reexecuting itself with the -sf parameter followed by the PIDs of +the workers. The master will then parse the configuration file and fork new +workers. + +To understand better how these signals are used, it is important to understand +the whole restart mechanism. + +First, an existing haproxy process is running. The administrator uses a system +specific command such as "/etc/init.d/haproxy reload" to indicate they want to +take the new configuration file into effect. What happens then is the following. +First, the service script (/etc/init.d/haproxy or equivalent) will verify that +the configuration file parses correctly using "haproxy -c". After that it will +try to start haproxy with this configuration file, using "-st" or "-sf". + +Then HAProxy tries to bind to all listening ports. If some fatal errors happen +(eg: address not present on the system, permission denied), the process quits +with an error. If a socket binding fails because a port is already in use, then +the process will first send a SIGTTOU signal to all the pids specified in the +"-st" or "-sf" pid list. This is what is called the "pause" signal. It instructs +all existing haproxy processes to temporarily stop listening to their ports so +that the new process can try to bind again. During this time, the old process +continues to process existing connections. If the binding still fails (because +for example a port is shared with another daemon), then the new process sends a +SIGTTIN signal to the old processes to instruct them to resume operations just +as if nothing happened. The old processes will then restart listening to the +ports and continue to accept connections. Note that this mechanism is system +dependent and some operating systems may not support it in multi-process mode. + +If the new process manages to bind correctly to all ports, then it sends either +the SIGTERM (hard stop in case of "-st") or the SIGUSR1 (graceful stop in case +of "-sf") to all processes to notify them that it is now in charge of operations +and that the old processes will have to leave, either immediately or once they +have finished their job. + +It is important to note that during this timeframe, there are two small windows +of a few milliseconds each where it is possible that a few connection failures +will be noticed during high loads. Typically observed failure rates are around +1 failure during a reload operation every 10000 new connections per second, +which means that a heavily loaded site running at 30000 new connections per +second may see about 3 failed connection upon every reload. The two situations +where this happens are : + + - if the new process fails to bind due to the presence of the old process, + it will first have to go through the SIGTTOU+SIGTTIN sequence, which + typically lasts about one millisecond for a few tens of frontends, and + during which some ports will not be bound to the old process and not yet + bound to the new one. HAProxy works around this on systems that support the + SO_REUSEPORT socket options, as it allows the new process to bind without + first asking the old one to unbind. Most BSD systems have been supporting + this almost forever. Linux has been supporting this in version 2.0 and + dropped it around 2.2, but some patches were floating around by then. It + was reintroduced in kernel 3.9, so if you are observing a connection + failure rate above the one mentioned above, please ensure that your kernel + is 3.9 or newer, or that relevant patches were backported to your kernel + (less likely). + + - when the old processes close the listening ports, the kernel may not always + redistribute any pending connection that was remaining in the socket's + backlog. Under high loads, a SYN packet may happen just before the socket + is closed, and will lead to an RST packet being sent to the client. In some + critical environments where even one drop is not acceptable, these ones are + sometimes dealt with using firewall rules to block SYN packets during the + reload, forcing the client to retransmit. This is totally system-dependent, + as some systems might be able to visit other listening queues and avoid + this RST. A second case concerns the ACK from the client on a local socket + that was in SYN_RECV state just before the close. This ACK will lead to an + RST packet while the haproxy process is still not aware of it. This one is + harder to get rid of, though the firewall filtering rules mentioned above + will work well if applied one second or so before restarting the process. + +For the vast majority of users, such drops will never ever happen since they +don't have enough load to trigger the race conditions. And for most high traffic +users, the failure rate is still fairly within the noise margin provided that at +least SO_REUSEPORT is properly supported on their systems. + +QUIC limitations: soft-stop is not supported. In case of reload, QUIC connections +will not be preserved. + +5. File-descriptor limitations +------------------------------ + +In order to ensure that all incoming connections will successfully be served, +HAProxy computes at load time the total number of file descriptors that will be +needed during the process's life. A regular Unix process is generally granted +1024 file descriptors by default, and a privileged process can raise this limit +itself. This is one reason for starting HAProxy as root and letting it adjust +the limit. The default limit of 1024 file descriptors roughly allow about 500 +concurrent connections to be processed. The computation is based on the global +maxconn parameter which limits the total number of connections per process, the +number of listeners, the number of servers which have a health check enabled, +the agent checks, the peers, the loggers and possibly a few other technical +requirements. A simple rough estimate of this number consists in simply +doubling the maxconn value and adding a few tens to get the approximate number +of file descriptors needed. + +Originally HAProxy did not know how to compute this value, and it was necessary +to pass the value using the "ulimit-n" setting in the global section. This +explains why even today a lot of configurations are seen with this setting +present. Unfortunately it was often miscalculated resulting in connection +failures when approaching maxconn instead of throttling incoming connection +while waiting for the needed resources. For this reason it is important to +remove any vestigial "ulimit-n" setting that can remain from very old versions. + +Raising the number of file descriptors to accept even moderate loads is +mandatory but comes with some OS-specific adjustments. First, the select() +polling system is limited to 1024 file descriptors. In fact on Linux it used +to be capable of handling more but since certain OS ship with excessively +restrictive SELinux policies forbidding the use of select() with more than +1024 file descriptors, HAProxy now refuses to start in this case in order to +avoid any issue at run time. On all supported operating systems, poll() is +available and will not suffer from this limitation. It is automatically picked +so there is nothing to do to get a working configuration. But poll's becomes +very slow when the number of file descriptors increases. While HAProxy does its +best to limit this performance impact (eg: via the use of the internal file +descriptor cache and batched processing), a good rule of thumb is that using +poll() with more than a thousand concurrent connections will use a lot of CPU. + +For Linux systems base on kernels 2.6 and above, the epoll() system call will +be used. It's a much more scalable mechanism relying on callbacks in the kernel +that guarantee a constant wake up time regardless of the number of registered +monitored file descriptors. It is automatically used where detected, provided +that HAProxy had been built for one of the Linux flavors. Its presence and +support can be verified using "haproxy -vv". + +For BSD systems which support it, kqueue() is available as an alternative. It +is much faster than poll() and even slightly faster than epoll() thanks to its +batched handling of changes. At least FreeBSD and OpenBSD support it. Just like +with Linux's epoll(), its support and availability are reported in the output +of "haproxy -vv". + +Having a good poller is one thing, but it is mandatory that the process can +reach the limits. When HAProxy starts, it immediately sets the new process's +file descriptor limits and verifies if it succeeds. In case of failure, it +reports it before forking so that the administrator can see the problem. As +long as the process is started by as root, there should be no reason for this +setting to fail. However, it can fail if the process is started by an +unprivileged user. If there is a compelling reason for *not* starting haproxy +as root (eg: started by end users, or by a per-application account), then the +file descriptor limit can be raised by the system administrator for this +specific user. The effectiveness of the setting can be verified by issuing +"ulimit -n" from the user's command line. It should reflect the new limit. + +Warning: when an unprivileged user's limits are changed in this user's account, +it is fairly common that these values are only considered when the user logs in +and not at all in some scripts run at system boot time nor in crontabs. This is +totally dependent on the operating system, keep in mind to check "ulimit -n" +before starting haproxy when running this way. The general advice is never to +start haproxy as an unprivileged user for production purposes. Another good +reason is that it prevents haproxy from enabling some security protections. + +Once it is certain that the system will allow the haproxy process to use the +requested number of file descriptors, two new system-specific limits may be +encountered. The first one is the system-wide file descriptor limit, which is +the total number of file descriptors opened on the system, covering all +processes. When this limit is reached, accept() or socket() will typically +return ENFILE. The second one is the per-process hard limit on the number of +file descriptors, it prevents setrlimit() from being set higher. Both are very +dependent on the operating system. On Linux, the system limit is set at boot +based on the amount of memory. It can be changed with the "fs.file-max" sysctl. +And the per-process hard limit is set to 1048576 by default, but it can be +changed using the "fs.nr_open" sysctl. + +File descriptor limitations may be observed on a running process when they are +set too low. The strace utility will report that accept() and socket() return +"-1 EMFILE" when the process's limits have been reached. In this case, simply +raising the "ulimit-n" value (or removing it) will solve the problem. If these +system calls return "-1 ENFILE" then it means that the kernel's limits have +been reached and that something must be done on a system-wide parameter. These +trouble must absolutely be addressed, as they result in high CPU usage (when +accept() fails) and failed connections that are generally visible to the user. +One solution also consists in lowering the global maxconn value to enforce +serialization, and possibly to disable HTTP keep-alive to force connections +to be released and reused faster. + + +6. Memory management +-------------------- + +HAProxy uses a simple and fast pool-based memory management. Since it relies on +a small number of different object types, it's much more efficient to pick new +objects from a pool which already contains objects of the appropriate size than +to call malloc() for each different size. The pools are organized as a stack or +LIFO, so that newly allocated objects are taken from recently released objects +still hot in the CPU caches. Pools of similar sizes are merged together, in +order to limit memory fragmentation. + +By default, since the focus is set on performance, each released object is put +back into the pool it came from, and allocated objects are never freed since +they are expected to be reused very soon. + +On the CLI, it is possible to check how memory is being used in pools thanks to +the "show pools" command : + + > show pools + Dumping pools usage. Use SIGQUIT to flush them. + - Pool cache_st (16 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 1 users, @0x9ccc40=03 [SHARED] + - Pool pipe (32 bytes) : 5 allocated (160 bytes), 5 used, 0 failures, 2 users, @0x9ccac0=00 [SHARED] + - Pool comp_state (48 bytes) : 3 allocated (144 bytes), 3 used, 0 failures, 5 users, @0x9cccc0=04 [SHARED] + - Pool filter (64 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 3 users, @0x9ccbc0=02 [SHARED] + - Pool vars (80 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 2 users, @0x9ccb40=01 [SHARED] + - Pool uniqueid (128 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 2 users, @0x9cd240=15 [SHARED] + - Pool task (144 bytes) : 55 allocated (7920 bytes), 55 used, 0 failures, 1 users, @0x9cd040=11 [SHARED] + - Pool session (160 bytes) : 1 allocated (160 bytes), 1 used, 0 failures, 1 users, @0x9cd140=13 [SHARED] + - Pool h2s (208 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 2 users, @0x9ccec0=08 [SHARED] + - Pool h2c (288 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 1 users, @0x9cce40=07 [SHARED] + - Pool spoe_ctx (304 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 2 users, @0x9ccf40=09 [SHARED] + - Pool connection (400 bytes) : 2 allocated (800 bytes), 2 used, 0 failures, 1 users, @0x9cd1c0=14 [SHARED] + - Pool hdr_idx (416 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 1 users, @0x9cd340=17 [SHARED] + - Pool dns_resolut (480 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 1 users, @0x9ccdc0=06 [SHARED] + - Pool dns_answer_ (576 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 1 users, @0x9ccd40=05 [SHARED] + - Pool stream (960 bytes) : 1 allocated (960 bytes), 1 used, 0 failures, 1 users, @0x9cd0c0=12 [SHARED] + - Pool requri (1024 bytes) : 0 allocated (0 bytes), 0 used, 0 failures, 1 users, @0x9cd2c0=16 [SHARED] + - Pool buffer (8030 bytes) : 3 allocated (24090 bytes), 2 used, 0 failures, 1 users, @0x9cd3c0=18 [SHARED] + - Pool trash (8062 bytes) : 1 allocated (8062 bytes), 1 used, 0 failures, 1 users, @0x9cd440=19 + Total: 19 pools, 42296 bytes allocated, 34266 used. + +The pool name is only indicative, it's the name of the first object type using +this pool. The size in parenthesis is the object size for objects in this pool. +Object sizes are always rounded up to the closest multiple of 16 bytes. The +number of objects currently allocated and the equivalent number of bytes is +reported so that it is easy to know which pool is responsible for the highest +memory usage. The number of objects currently in use is reported as well in the +"used" field. The difference between "allocated" and "used" corresponds to the +objects that have been freed and are available for immediate use. The address +at the end of the line is the pool's address, and the following number is the +pool index when it exists, or is reported as -1 if no index was assigned. + +It is possible to limit the amount of memory allocated per process using the +"-m" command line option, followed by a number of megabytes. It covers all of +the process's addressable space, so that includes memory used by some libraries +as well as the stack, but it is a reliable limit when building a resource +constrained system. It works the same way as "ulimit -v" on systems which have +it, or "ulimit -d" for the other ones. + +If a memory allocation fails due to the memory limit being reached or because +the system doesn't have any enough memory, then haproxy will first start to +free all available objects from all pools before attempting to allocate memory +again. This mechanism of releasing unused memory can be triggered by sending +the signal SIGQUIT to the haproxy process. When doing so, the pools state prior +to the flush will also be reported to stderr when the process runs in +foreground. + +During a reload operation, the process switched to the graceful stop state also +automatically performs some flushes after releasing any connection so that all +possible memory is released to save it for the new process. + + +7. CPU usage +------------ + +HAProxy normally spends most of its time in the system and a smaller part in +userland. A finely tuned 3.5 GHz CPU can sustain a rate about 80000 end-to-end +connection setups and closes per second at 100% CPU on a single core. When one +core is saturated, typical figures are : + - 95% system, 5% user for long TCP connections or large HTTP objects + - 85% system and 15% user for short TCP connections or small HTTP objects in + close mode + - 70% system and 30% user for small HTTP objects in keep-alive mode + +The amount of rules processing and regular expressions will increase the user +land part. The presence of firewall rules, connection tracking, complex routing +tables in the system will instead increase the system part. + +On most systems, the CPU time observed during network transfers can be cut in 4 +parts : + - the interrupt part, which concerns all the processing performed upon I/O + receipt, before the target process is even known. Typically Rx packets are + accounted for in interrupt. On some systems such as Linux where interrupt + processing may be deferred to a dedicated thread, it can appear as softirq, + and the thread is called ksoftirqd/0 (for CPU 0). The CPU taking care of + this load is generally defined by the hardware settings, though in the case + of softirq it is often possible to remap the processing to another CPU. + This interrupt part will often be perceived as parasitic since it's not + associated with any process, but it actually is some processing being done + to prepare the work for the process. + + - the system part, which concerns all the processing done using kernel code + called from userland. System calls are accounted as system for example. All + synchronously delivered Tx packets will be accounted for as system time. If + some packets have to be deferred due to queues filling up, they may then be + processed in interrupt context later (eg: upon receipt of an ACK opening a + TCP window). + + - the user part, which exclusively runs application code in userland. HAProxy + runs exclusively in this part, though it makes heavy use of system calls. + Rules processing, regular expressions, compression, encryption all add to + the user portion of CPU consumption. + + - the idle part, which is what the CPU does when there is nothing to do. For + example HAProxy waits for an incoming connection, or waits for some data to + leave, meaning the system is waiting for an ACK from the client to push + these data. + +In practice regarding HAProxy's activity, it is in general reasonably accurate +(but totally inexact) to consider that interrupt/softirq are caused by Rx +processing in kernel drivers, that user-land is caused by layer 7 processing +in HAProxy, and that system time is caused by network processing on the Tx +path. + +Since HAProxy runs around an event loop, it waits for new events using poll() +(or any alternative) and processes all these events as fast as possible before +going back to poll() waiting for new events. It measures the time spent waiting +in poll() compared to the time spent doing processing events. The ratio of +polling time vs total time is called the "idle" time, it's the amount of time +spent waiting for something to happen. This ratio is reported in the stats page +on the "idle" line, or "Idle_pct" on the CLI. When it's close to 100%, it means +the load is extremely low. When it's close to 0%, it means that there is +constantly some activity. While it cannot be very accurate on an overloaded +system due to other processes possibly preempting the CPU from the haproxy +process, it still provides a good estimate about how HAProxy considers it is +working : if the load is low and the idle ratio is low as well, it may indicate +that HAProxy has a lot of work to do, possibly due to very expensive rules that +have to be processed. Conversely, if HAProxy indicates the idle is close to +100% while things are slow, it means that it cannot do anything to speed things +up because it is already waiting for incoming data to process. In the example +below, haproxy is completely idle : + + $ echo "show info" | socat - /var/run/haproxy.sock | grep ^Idle + Idle_pct: 100 + +When the idle ratio starts to become very low, it is important to tune the +system and place processes and interrupts correctly to save the most possible +CPU resources for all tasks. If a firewall is present, it may be worth trying +to disable it or to tune it to ensure it is not responsible for a large part +of the performance limitation. It's worth noting that unloading a stateful +firewall generally reduces both the amount of interrupt/softirq and of system +usage since such firewalls act both on the Rx and the Tx paths. On Linux, +unloading the nf_conntrack and ip_conntrack modules will show whether there is +anything to gain. If so, then the module runs with default settings and you'll +have to figure how to tune it for better performance. In general this consists +in considerably increasing the hash table size. On FreeBSD, "pfctl -d" will +disable the "pf" firewall and its stateful engine at the same time. + +If it is observed that a lot of time is spent in interrupt/softirq, it is +important to ensure that they don't run on the same CPU. Most systems tend to +pin the tasks on the CPU where they receive the network traffic because for +certain workloads it improves things. But with heavily network-bound workloads +it is the opposite as the haproxy process will have to fight against its kernel +counterpart. Pinning haproxy to one CPU core and the interrupts to another one, +all sharing the same L3 cache tends to sensibly increase network performance +because in practice the amount of work for haproxy and the network stack are +quite close, so they can almost fill an entire CPU each. On Linux this is done +using taskset (for haproxy) or using cpu-map (from the haproxy config), and the +interrupts are assigned under /proc/irq. Many network interfaces support +multiple queues and multiple interrupts. In general it helps to spread them +across a small number of CPU cores provided they all share the same L3 cache. +Please always stop irq_balance which always does the worst possible thing on +such workloads. + +For CPU-bound workloads consisting in a lot of SSL traffic or a lot of +compression, it may be worth using multiple processes dedicated to certain +tasks, though there is no universal rule here and experimentation will have to +be performed. + +In order to increase the CPU capacity, it is possible to make HAProxy run as +several processes, using the "nbproc" directive in the global section. There +are some limitations though : + - health checks are run per process, so the target servers will get as many + checks as there are running processes ; + - maxconn values and queues are per-process so the correct value must be set + to avoid overloading the servers ; + - outgoing connections should avoid using port ranges to avoid conflicts + - stick-tables are per process and are not shared between processes ; + - each peers section may only run on a single process at a time ; + - the CLI operations will only act on a single process at a time. + +With this in mind, it appears that the easiest setup often consists in having +one first layer running on multiple processes and in charge for the heavy +processing, passing the traffic to a second layer running in a single process. +This mechanism is suited to SSL and compression which are the two CPU-heavy +features. Instances can easily be chained over UNIX sockets (which are cheaper +than TCP sockets and which do not waste ports), and the proxy protocol which is +useful to pass client information to the next stage. When doing so, it is +generally a good idea to bind all the single-process tasks to process number 1 +and extra tasks to next processes, as this will make it easier to generate +similar configurations for different machines. + +On Linux versions 3.9 and above, running HAProxy in multi-process mode is much +more efficient when each process uses a distinct listening socket on the same +IP:port ; this will make the kernel evenly distribute the load across all +processes instead of waking them all up. Please check the "process" option of +the "bind" keyword lines in the configuration manual for more information. + + +8. Logging +---------- + +For logging, HAProxy always relies on a syslog server since it does not perform +any file-system access. The standard way of using it is to send logs over UDP +to the log server (by default on port 514). Very commonly this is configured to +127.0.0.1 where the local syslog daemon is running, but it's also used over the +network to log to a central server. The central server provides additional +benefits especially in active-active scenarios where it is desirable to keep +the logs merged in arrival order. HAProxy may also make use of a UNIX socket to +send its logs to the local syslog daemon, but it is not recommended at all, +because if the syslog server is restarted while haproxy runs, the socket will +be replaced and new logs will be lost. Since HAProxy will be isolated inside a +chroot jail, it will not have the ability to reconnect to the new socket. It +has also been observed in field that the log buffers in use on UNIX sockets are +very small and lead to lost messages even at very light loads. But this can be +fine for testing however. + +It is recommended to add the following directive to the "global" section to +make HAProxy log to the local daemon using facility "local0" : + + log 127.0.0.1:514 local0 + +and then to add the following one to each "defaults" section or to each frontend +and backend section : + + log global + +This way, all logs will be centralized through the global definition of where +the log server is. + +Some syslog daemons do not listen to UDP traffic by default, so depending on +the daemon being used, the syntax to enable this will vary : + + - on sysklogd, you need to pass argument "-r" on the daemon's command line + so that it listens to a UDP socket for "remote" logs ; note that there is + no way to limit it to address 127.0.0.1 so it will also receive logs from + remote systems ; + + - on rsyslogd, the following lines must be added to the configuration file : + + $ModLoad imudp + $UDPServerAddress * + $UDPServerRun 514 + + - on syslog-ng, a new source can be created the following way, it then needs + to be added as a valid source in one of the "log" directives : + + source s_udp { + udp(ip(127.0.0.1) port(514)); + }; + +Please consult your syslog daemon's manual for more information. If no logs are +seen in the system's log files, please consider the following tests : + + - restart haproxy. Each frontend and backend logs one line indicating it's + starting. If these logs are received, it means logs are working. + + - run "strace -tt -s100 -etrace=sendmsg -p " and perform some + activity that you expect to be logged. You should see the log messages + being sent using sendmsg() there. If they don't appear, restart using + strace on top of haproxy. If you still see no logs, it definitely means + that something is wrong in your configuration. + + - run tcpdump to watch for port 514, for example on the loopback interface if + the traffic is being sent locally : "tcpdump -As0 -ni lo port 514". If the + packets are seen there, it's the proof they're sent then the syslogd daemon + needs to be troubleshooted. + +While traffic logs are sent from the frontends (where the incoming connections +are accepted), backends also need to be able to send logs in order to report a +server state change consecutive to a health check. Please consult HAProxy's +configuration manual for more information regarding all possible log settings. + +It is convenient to chose a facility that is not used by other daemons. HAProxy +examples often suggest "local0" for traffic logs and "local1" for admin logs +because they're never seen in field. A single facility would be enough as well. +Having separate logs is convenient for log analysis, but it's also important to +remember that logs may sometimes convey confidential information, and as such +they must not be mixed with other logs that may accidentally be handed out to +unauthorized people. + +For in-field troubleshooting without impacting the server's capacity too much, +it is recommended to make use of the "halog" utility provided with HAProxy. +This is sort of a grep-like utility designed to process HAProxy log files at +a very fast data rate. Typical figures range between 1 and 2 GB of logs per +second. It is capable of extracting only certain logs (eg: search for some +classes of HTTP status codes, connection termination status, search by response +time ranges, look for errors only), count lines, limit the output to a number +of lines, and perform some more advanced statistics such as sorting servers +by response time or error counts, sorting URLs by time or count, sorting client +addresses by access count, and so on. It is pretty convenient to quickly spot +anomalies such as a bot looping on the site, and block them. + + +9. Statistics and monitoring +---------------------------- + +It is possible to query HAProxy about its status. The most commonly used +mechanism is the HTTP statistics page. This page also exposes an alternative +CSV output format for monitoring tools. The same format is provided on the +Unix socket. + +Statistics are regroup in categories labelled as domains, corresponding to the +multiple components of HAProxy. There are two domains available: proxy and dns. +If not specified, the proxy domain is selected. Note that only the proxy +statistics are printed on the HTTP page. + +9.1. CSV format +--------------- + +The statistics may be consulted either from the unix socket or from the HTTP +page. Both means provide a CSV format whose fields follow. The first line +begins with a sharp ('#') and has one word per comma-delimited field which +represents the title of the column. All other lines starting at the second one +use a classical CSV format using a comma as the delimiter, and the double quote +('"') as an optional text delimiter, but only if the enclosed text is ambiguous +(if it contains a quote or a comma). The double-quote character ('"') in the +text is doubled ('""'), which is the format that most tools recognize. Please +do not insert any column before these ones in order not to break tools which +use hard-coded column positions. + +For proxy statistics, after each field name, the types which may have a value +for that field are specified in brackets. The types are L (Listeners), F +(Frontends), B (Backends), and S (Servers). There is a fixed set of static +fields that are always available in the same order. A column containing the +character '-' delimits the end of the static fields, after which presence or +order of the fields are not guaranteed. + +Here is the list of static fields using the proxy statistics domain: + 0. pxname [LFBS]: proxy name + 1. svname [LFBS]: service name (FRONTEND for frontend, BACKEND for backend, + any name for server/listener) + 2. qcur [..BS]: current queued requests. For the backend this reports the + number queued without a server assigned. + 3. qmax [..BS]: max value of qcur + 4. scur [LFBS]: current sessions + 5. smax [LFBS]: max sessions + 6. slim [LFBS]: configured session limit + 7. stot [LFBS]: cumulative number of sessions + 8. bin [LFBS]: bytes in + 9. bout [LFBS]: bytes out + 10. dreq [LFB.]: requests denied because of security concerns. + - For tcp this is because of a matched tcp-request content rule. + - For http this is because of a matched http-request or tarpit rule. + 11. dresp [LFBS]: responses denied because of security concerns. + - For http this is because of a matched http-request rule, or + "option checkcache". + 12. ereq [LF..]: request errors. Some of the possible causes are: + - early termination from the client, before the request has been sent. + - read error from the client + - client timeout + - client closed connection + - various bad requests from the client. + - request was tarpitted. + 13. econ [..BS]: number of requests that encountered an error trying to + connect to a backend server. The backend stat is the sum of the stat + for all servers of that backend, plus any connection errors not + associated with a particular server (such as the backend having no + active servers). + 14. eresp [..BS]: response errors. srv_abrt will be counted here also. + Some other errors are: + - write error on the client socket (won't be counted for the server stat) + - failure applying filters to the response. + 15. wretr [..BS]: number of times a connection to a server was retried. + 16. wredis [..BS]: number of times a request was redispatched to another + server. The server value counts the number of times that server was + switched away from. + 17. status [LFBS]: status (UP/DOWN/NOLB/MAINT/MAINT(via)/MAINT(resolution)...) + 18. weight [..BS]: total effective weight (backend), effective weight (server) + 19. act [..BS]: number of active servers (backend), server is active (server) + 20. bck [..BS]: number of backup servers (backend), server is backup (server) + 21. chkfail [...S]: number of failed checks. (Only counts checks failed when + the server is up.) + 22. chkdown [..BS]: number of UP->DOWN transitions. The backend counter counts + transitions to the whole backend being down, rather than the sum of the + counters for each server. + 23. lastchg [..BS]: number of seconds since the last UP<->DOWN transition + 24. downtime [..BS]: total downtime (in seconds). The value for the backend + is the downtime for the whole backend, not the sum of the server downtime. + 25. qlimit [...S]: configured maxqueue for the server, or nothing in the + value is 0 (default, meaning no limit) + 26. pid [LFBS]: process id (0 for first instance, 1 for second, ...) + 27. iid [LFBS]: unique proxy id + 28. sid [L..S]: server id (unique inside a proxy) + 29. throttle [...S]: current throttle percentage for the server, when + slowstart is active, or no value if not in slowstart. + 30. lbtot [..BS]: total number of times a server was selected, either for new + sessions, or when re-dispatching. The server counter is the number + of times that server was selected. + 31. tracked [...S]: id of proxy/server if tracking is enabled. + 32. type [LFBS]: (0=frontend, 1=backend, 2=server, 3=socket/listener) + 33. rate [.FBS]: number of sessions per second over last elapsed second + 34. rate_lim [.F..]: configured limit on new sessions per second + 35. rate_max [.FBS]: max number of new sessions per second + 36. check_status [...S]: status of last health check, one of: + UNK -> unknown + INI -> initializing + SOCKERR -> socket error + L4OK -> check passed on layer 4, no upper layers testing enabled + L4TOUT -> layer 1-4 timeout + L4CON -> layer 1-4 connection problem, for example + "Connection refused" (tcp rst) or "No route to host" (icmp) + L6OK -> check passed on layer 6 + L6TOUT -> layer 6 (SSL) timeout + L6RSP -> layer 6 invalid response - protocol error + L7OK -> check passed on layer 7 + L7OKC -> check conditionally passed on layer 7, for example 404 with + disable-on-404 + L7TOUT -> layer 7 (HTTP/SMTP) timeout + L7RSP -> layer 7 invalid response - protocol error + L7STS -> layer 7 response error, for example HTTP 5xx + Notice: If a check is currently running, the last known status will be + reported, prefixed with "* ". e. g. "* L7OK". + 37. check_code [...S]: layer5-7 code, if available + 38. check_duration [...S]: time in ms took to finish last health check + 39. hrsp_1xx [.FBS]: http responses with 1xx code + 40. hrsp_2xx [.FBS]: http responses with 2xx code + 41. hrsp_3xx [.FBS]: http responses with 3xx code + 42. hrsp_4xx [.FBS]: http responses with 4xx code + 43. hrsp_5xx [.FBS]: http responses with 5xx code + 44. hrsp_other [.FBS]: http responses with other codes (protocol error) + 45. hanafail [...S]: failed health checks details + 46. req_rate [.F..]: HTTP requests per second over last elapsed second + 47. req_rate_max [.F..]: max number of HTTP requests per second observed + 48. req_tot [.FB.]: total number of HTTP requests received + 49. cli_abrt [..BS]: number of data transfers aborted by the client + 50. srv_abrt [..BS]: number of data transfers aborted by the server + (inc. in eresp) + 51. comp_in [.FB.]: number of HTTP response bytes fed to the compressor + 52. comp_out [.FB.]: number of HTTP response bytes emitted by the compressor + 53. comp_byp [.FB.]: number of bytes that bypassed the HTTP compressor + (CPU/BW limit) + 54. comp_rsp [.FB.]: number of HTTP responses that were compressed + 55. lastsess [..BS]: number of seconds since last session assigned to + server/backend + 56. last_chk [...S]: last health check contents or textual error + 57. last_agt [...S]: last agent check contents or textual error + 58. qtime [..BS]: the average queue time in ms over the 1024 last requests + 59. ctime [..BS]: the average connect time in ms over the 1024 last requests + 60. rtime [..BS]: the average response time in ms over the 1024 last requests + (0 for TCP) + 61. ttime [..BS]: the average total session time in ms over the 1024 last + requests + 62. agent_status [...S]: status of last agent check, one of: + UNK -> unknown + INI -> initializing + SOCKERR -> socket error + L4OK -> check passed on layer 4, no upper layers testing enabled + L4TOUT -> layer 1-4 timeout + L4CON -> layer 1-4 connection problem, for example + "Connection refused" (tcp rst) or "No route to host" (icmp) + L7OK -> agent reported "up" + L7STS -> agent reported "fail", "stop", or "down" + 63. agent_code [...S]: numeric code reported by agent if any (unused for now) + 64. agent_duration [...S]: time in ms taken to finish last check + 65. check_desc [...S]: short human-readable description of check_status + 66. agent_desc [...S]: short human-readable description of agent_status + 67. check_rise [...S]: server's "rise" parameter used by checks + 68. check_fall [...S]: server's "fall" parameter used by checks + 69. check_health [...S]: server's health check value between 0 and rise+fall-1 + 70. agent_rise [...S]: agent's "rise" parameter, normally 1 + 71. agent_fall [...S]: agent's "fall" parameter, normally 1 + 72. agent_health [...S]: agent's health parameter, between 0 and rise+fall-1 + 73. addr [L..S]: address:port or "unix". IPv6 has brackets around the address. + 74: cookie [..BS]: server's cookie value or backend's cookie name + 75: mode [LFBS]: proxy mode (tcp, http, health, unknown) + 76: algo [..B.]: load balancing algorithm + 77: conn_rate [.F..]: number of connections over the last elapsed second + 78: conn_rate_max [.F..]: highest known conn_rate + 79: conn_tot [.F..]: cumulative number of connections + 80: intercepted [.FB.]: cum. number of intercepted requests (monitor, stats) + 81: dcon [LF..]: requests denied by "tcp-request connection" rules + 82: dses [LF..]: requests denied by "tcp-request session" rules + 83: wrew [LFBS]: cumulative number of failed header rewriting warnings + 84: connect [..BS]: cumulative number of connection establishment attempts + 85: reuse [..BS]: cumulative number of connection reuses + 86: cache_lookups [.FB.]: cumulative number of cache lookups + 87: cache_hits [.FB.]: cumulative number of cache hits + 88: srv_icur [...S]: current number of idle connections available for reuse + 89: src_ilim [...S]: limit on the number of available idle connections + 90. qtime_max [..BS]: the maximum observed queue time in ms + 91. ctime_max [..BS]: the maximum observed connect time in ms + 92. rtime_max [..BS]: the maximum observed response time in ms (0 for TCP) + 93. ttime_max [..BS]: the maximum observed total session time in ms + 94. eint [LFBS]: cumulative number of internal errors + 95. idle_conn_cur [...S]: current number of unsafe idle connections + 96. safe_conn_cur [...S]: current number of safe idle connections + 97. used_conn_cur [...S]: current number of connections in use + 98. need_conn_est [...S]: estimated needed number of connections + 99. uweight [..BS]: total user weight (backend), server user weight (server) + +For all other statistics domains, the presence or the order of the fields are +not guaranteed. In this case, the header line should always be used to parse +the CSV data. + +9.2. Typed output format +------------------------ + +Both "show info" and "show stat" support a mode where each output value comes +with its type and sufficient information to know how the value is supposed to +be aggregated between processes and how it evolves. + +In all cases, the output consists in having a single value per line with all +the information split into fields delimited by colons (':'). + +The first column designates the object or metric being dumped. Its format is +specific to the command producing this output and will not be described in this +section. Usually it will consist in a series of identifiers and field names. + +The second column contains 3 characters respectively indicating the origin, the +nature and the scope of the value being reported. The first character (the +origin) indicates where the value was extracted from. Possible characters are : + + M The value is a metric. It is valid at one instant any may change depending + on its nature . + + S The value is a status. It represents a discrete value which by definition + cannot be aggregated. It may be the status of a server ("UP" or "DOWN"), + the PID of the process, etc. + + K The value is a sorting key. It represents an identifier which may be used + to group some values together because it is unique among its class. All + internal identifiers are keys. Some names can be listed as keys if they + are unique (eg: a frontend name is unique). In general keys come from the + configuration, even though some of them may automatically be assigned. For + most purposes keys may be considered as equivalent to configuration. + + C The value comes from the configuration. Certain configuration values make + sense on the output, for example a concurrent connection limit or a cookie + name. By definition these values are the same in all processes started + from the same configuration file. + + P The value comes from the product itself. There are very few such values, + most common use is to report the product name, version and release date. + These elements are also the same between all processes. + +The second character (the nature) indicates the nature of the information +carried by the field in order to let an aggregator decide on what operation to +use to aggregate multiple values. Possible characters are : + + A The value represents an age since a last event. This is a bit different + from the duration in that an age is automatically computed based on the + current date. A typical example is how long ago did the last session + happen on a server. Ages are generally aggregated by taking the minimum + value and do not need to be stored. + + a The value represents an already averaged value. The average response times + and server weights are of this nature. Averages can typically be averaged + between processes. + + C The value represents a cumulative counter. Such measures perpetually + increase until they wrap around. Some monitoring protocols need to tell + the difference between a counter and a gauge to report a different type. + In general counters may simply be summed since they represent events or + volumes. Examples of metrics of this nature are connection counts or byte + counts. + + D The value represents a duration for a status. There are a few usages of + this, most of them include the time taken by the last health check and + the time a server has spent down. Durations are generally not summed, + most of the time the maximum will be retained to compute an SLA. + + G The value represents a gauge. It's a measure at one instant. The memory + usage or the current number of active connections are of this nature. + Metrics of this type are typically summed during aggregation. + + L The value represents a limit (generally a configured one). By nature, + limits are harder to aggregate since they are specific to the point where + they were retrieved. In certain situations they may be summed or be kept + separate. + + M The value represents a maximum. In general it will apply to a gauge and + keep the highest known value. An example of such a metric could be the + maximum amount of concurrent connections that was encountered in the + product's life time. To correctly aggregate maxima, you are supposed to + output a range going from the maximum of all maxima and the sum of all + of them. There is indeed no way to know if they were encountered + simultaneously or not. + + m The value represents a minimum. In general it will apply to a gauge and + keep the lowest known value. An example of such a metric could be the + minimum amount of free memory pools that was encountered in the product's + life time. To correctly aggregate minima, you are supposed to output a + range going from the minimum of all minima and the sum of all of them. + There is indeed no way to know if they were encountered simultaneously + or not. + + N The value represents a name, so it is a string. It is used to report + proxy names, server names and cookie names. Names have configuration or + keys as their origin and are supposed to be the same among all processes. + + O The value represents a free text output. Outputs from various commands, + returns from health checks, node descriptions are of such nature. + + R The value represents an event rate. It's a measure at one instant. It is + quite similar to a gauge except that the recipient knows that this measure + moves slowly and may decide not to keep all values. An example of such a + metric is the measured amount of connections per second. Metrics of this + type are typically summed during aggregation. + + T The value represents a date or time. A field emitting the current date + would be of this type. The method to aggregate such information is left + as an implementation choice. For now no field uses this type. + +The third character (the scope) indicates what extent the value reflects. Some +elements may be per process while others may be per configuration or per system. +The distinction is important to know whether or not a single value should be +kept during aggregation or if values have to be aggregated. The following +characters are currently supported : + + C The value is valid for a whole cluster of nodes, which is the set of nodes + communicating over the peers protocol. An example could be the amount of + entries present in a stick table that is replicated with other peers. At + the moment no metric use this scope. + + P The value is valid only for the process reporting it. Most metrics use + this scope. + + S The value is valid for the whole service, which is the set of processes + started together from the same configuration file. All metrics originating + from the configuration use this scope. Some other metrics may use it as + well for some shared resources (eg: shared SSL cache statistics). + + s The value is valid for the whole system, such as the system's hostname, + current date or resource usage. At the moment this scope is not used by + any metric. + +Consumers of these information will generally have enough of these 3 characters +to determine how to accurately report aggregated information across multiple +processes. + +After this column, the third column indicates the type of the field, among "s32" +(signed 32-bit integer), "s64" (signed 64-bit integer), "u32" (unsigned 32-bit +integer), "u64" (unsigned 64-bit integer), "str" (string). It is important to +know the type before parsing the value in order to properly read it. For example +a string containing only digits is still a string an not an integer (eg: an +error code extracted by a check). + +Then the fourth column is the value itself, encoded according to its type. +Strings are dumped as-is immediately after the colon without any leading space. +If a string contains a colon, it will appear normally. This means that the +output should not be exclusively split around colons or some check outputs +or server addresses might be truncated. + + +9.3. Unix Socket commands +------------------------- + +The stats socket is not enabled by default. In order to enable it, it is +necessary to add one line in the global section of the haproxy configuration. +A second line is recommended to set a larger timeout, always appreciated when +issuing commands by hand : + + global + stats socket /var/run/haproxy.sock mode 600 level admin + stats timeout 2m + +It is also possible to add multiple instances of the stats socket by repeating +the line, and make them listen to a TCP port instead of a UNIX socket. This is +never done by default because this is dangerous, but can be handy in some +situations : + + global + stats socket /var/run/haproxy.sock mode 600 level admin + stats socket ipv4@192.168.0.1:9999 level admin + stats timeout 2m + +To access the socket, an external utility such as "socat" is required. Socat is +a swiss-army knife to connect anything to anything. We use it to connect +terminals to the socket, or a couple of stdin/stdout pipes to it for scripts. +The two main syntaxes we'll use are the following : + + # socat /var/run/haproxy.sock stdio + # socat /var/run/haproxy.sock readline + +The first one is used with scripts. It is possible to send the output of a +script to haproxy, and pass haproxy's output to another script. That's useful +for retrieving counters or attack traces for example. + +The second one is only useful for issuing commands by hand. It has the benefit +that the terminal is handled by the readline library which supports line +editing and history, which is very convenient when issuing repeated commands +(eg: watch a counter). + +The socket supports two operation modes : + - interactive + - non-interactive + +The non-interactive mode is the default when socat connects to the socket. In +this mode, a single line may be sent. It is processed as a whole, responses are +sent back, and the connection closes after the end of the response. This is the +mode that scripts and monitoring tools use. It is possible to send multiple +commands in this mode, they need to be delimited by a semi-colon (';'). For +example : + + # echo "show info;show stat;show table" | socat /var/run/haproxy stdio + +If a command needs to use a semi-colon or a backslash (eg: in a value), it +must be preceded by a backslash ('\'). + +The interactive mode displays a prompt ('>') and waits for commands to be +entered on the line, then processes them, and displays the prompt again to wait +for a new command. This mode is entered via the "prompt" command which must be +sent on the first line in non-interactive mode. The mode is a flip switch, if +"prompt" is sent in interactive mode, it is disabled and the connection closes +after processing the last command of the same line. + +For this reason, when debugging by hand, it's quite common to start with the +"prompt" command : + + # socat /var/run/haproxy readline + prompt + > show info + ... + > + +Since multiple commands may be issued at once, haproxy uses the empty line as a +delimiter to mark an end of output for each command, and takes care of ensuring +that no command can emit an empty line on output. A script can thus easily +parse the output even when multiple commands were pipelined on a single line. + +Some commands may take an optional payload. To add one to a command, the first +line needs to end with the "<<\n" pattern. The next lines will be treated as +the payload and can contain as many lines as needed. To validate a command with +a payload, it needs to end with an empty line. + +Limitations do exist: the length of the whole buffer passed to the CLI must +not be greater than tune.bfsize and the pattern "<<" must not be glued to the +last word of the line. + +When entering a paylod while in interactive mode, the prompt will change from +"> " to "+ ". + +It is important to understand that when multiple haproxy processes are started +on the same sockets, any process may pick up the request and will output its +own stats. + +The list of commands currently supported on the stats socket is provided below. +If an unknown command is sent, haproxy displays the usage message which reminds +all supported commands. Some commands support a more complex syntax, generally +it will explain what part of the command is invalid when this happens. + +Some commands require a higher level of privilege to work. If you do not have +enough privilege, you will get an error "Permission denied". Please check +the "level" option of the "bind" keyword lines in the configuration manual +for more information. + +abort ssl ca-file + Abort and destroy a temporary CA file update transaction. + + See also "set ssl ca-file" and "commit ssl ca-file". + +abort ssl cert + Abort and destroy a temporary SSL certificate update transaction. + + See also "set ssl cert" and "commit ssl cert". + +abort ssl crl-file + Abort and destroy a temporary CRL file update transaction. + + See also "set ssl crl-file" and "commit ssl crl-file". + +add acl [@] + Add an entry into the acl . is the # or the returned by + "show acl". This command does not verify if the entry already exists. Entries + are added to the current version of the ACL, unless a specific version is + specified with "@". This version number must have preliminary been + allocated by "prepare acl", and it will be comprised between the versions + reported in "curr_ver" and "next_ver" on the output of "show acl". Entries + added with a specific version number will not match until a "commit acl" + operation is performed on them. They may however be consulted using the + "show acl @" command, and cleared using a "clear acl @" command. + This command cannot be used if the reference is a file also used with + a map. In this case, the "add map" command must be used instead. + +add map [@] +add map [@] + Add an entry into the map to associate the value to the key + . This command does not verify if the entry already exists. It is + mainly used to fill a map after a "clear" or "prepare" operation. Entries + are added to the current version of the ACL, unless a specific version is + specified with "@". This version number must have preliminary been + allocated by "prepare acl", and it will be comprised between the versions + reported in "curr_ver" and "next_ver" on the output of "show acl". Entries + added with a specific version number will not match until a "commit map" + operation is performed on them. They may however be consulted using the + "show map @" command, and cleared using a "clear acl @" command. + If the designated map is also used as an ACL, the ACL will only match the + part and will ignore the part. Using the payload syntax it is + possible to add multiple key/value pairs by entering them on separate lines. + On each new line, the first word is the key and the rest of the line is + considered to be the value which can even contains spaces. + + Example: + + # socat /tmp/sock1 - + prompt + + > add map #-1 << + + key1 value1 + + key2 value2 with spaces + + key3 value3 also with spaces + + key4 value4 + + > + +add server / [args]* + Instantiate a new server attached to the backend . + + The name must not be already used in the backend. A special + restriction is put on the backend which must used a dynamic load-balancing + algorithm. A subset of keywords from the server config file statement can be + used to configure the server behavior. Also note that no settings will be + reused from an hypothetical 'default-server' statement in the same backend. + + Currently a dynamic server is statically initialized with the "none" + init-addr method. This means that no resolution will be undertaken if a FQDN + is specified as an address, even if the server creation will be validated. + + To support the reload operations, it is expected that the server created via + the CLI is also manually inserted in the relevant haproxy configuration file. + A dynamic server not present in the configuration won't be restored after a + reload operation. + + A dynamic server may use the "track" keyword to follow the check status of + another server from the configuration. However, it is not possible to track + another dynamic server. This is to ensure that the tracking chain is kept + consistent even in the case of dynamic servers deletion. + + Use the "check" keyword to enable health-check support. Note that the + health-check is disabled by default and must be enabled independently from + the server using the "enable health" command. For agent checks, use the + "agent-check" keyword and the "enable agent" command. Note that in this case + the server may be activated via the agent depending on the status reported, + without an explicit "enable server" command. This also means that extra care + is required when removing a dynamic server with agent check. The agent should + be first deactivated via "disable agent" to be able to put the server in the + required maintenance mode before removal. + + It may be possible to reach the fd limit when using a large number of dynamic + servers. Please refer to the "u-limit" global keyword documentation in this + case. + + Here is the list of the currently supported keywords : + + - agent-addr + - agent-check + - agent-inter + - agent-port + - agent-send + - allow-0rtt + - alpn + - addr + - backup + - ca-file + - check + - check-alpn + - check-proto + - check-send-proxy + - check-sni + - check-ssl + - check-via-socks4 + - ciphers + - ciphersuites + - crl-file + - crt + - disabled + - downinter + - enabled + - error-limit + - fall + - fastinter + - force-sslv3/tlsv10/tlsv11/tlsv12/tlsv13 + - id + - inter + - maxconn + - maxqueue + - minconn + - no-ssl-reuse + - no-sslv3/tlsv10/tlsv11/tlsv12/tlsv13 + - no-tls-tickets + - npn + - observe + - on-error + - on-marked-down + - on-marked-up + - pool-low-conn + - pool-max-conn + - pool-purge-delay + - port + - proto + - proxy-v2-options + - rise + - send-proxy + - send-proxy-v2 + - send-proxy-v2-ssl + - send-proxy-v2-ssl-cn + - slowstart + - sni + - source + - ssl + - ssl-max-ver + - ssl-min-ver + - tfo + - tls-tickets + - track + - usesrc + - verify + - verifyhost + - weight + - ws + + Their syntax is similar to the server line from the configuration file, + please refer to their individual documentation for details. + +add ssl crt-list +add ssl crt-list + Add an certificate in a crt-list. It can also be used for directories since + directories are now loaded the same way as the crt-lists. This command allow + you to use a certificate name in parameter, to use SSL options or filters a + crt-list line must sent as a payload instead. Only one crt-list line is + supported in the payload. This command will load the certificate for every + bind lines using the crt-list. To push a new certificate to HAProxy the + commands "new ssl cert" and "set ssl cert" must be used. + + Example: + $ echo "new ssl cert foobar.pem" | socat /tmp/sock1 - + $ echo -e "set ssl cert foobar.pem <<\n$(cat foobar.pem)\n" | socat + /tmp/sock1 - + $ echo "commit ssl cert foobar.pem" | socat /tmp/sock1 - + $ echo "add ssl crt-list certlist1 foobar.pem" | socat /tmp/sock1 - + + $ echo -e 'add ssl crt-list certlist1 <<\nfoobar.pem [allow-0rtt] foo.bar.com + !test1.com\n' | socat /tmp/sock1 - + +clear counters + Clear the max values of the statistics counters in each proxy (frontend & + backend) and in each server. The accumulated counters are not affected. The + internal activity counters reported by "show activity" are also reset. This + can be used to get clean counters after an incident, without having to + restart nor to clear traffic counters. This command is restricted and can + only be issued on sockets configured for levels "operator" or "admin". + +clear counters all + Clear all statistics counters in each proxy (frontend & backend) and in each + server. This has the same effect as restarting. This command is restricted + and can only be issued on sockets configured for level "admin". + +clear acl [@] + Remove all entries from the acl . is the # or the + returned by "show acl". Note that if the reference is a file and is + shared with a map, this map will be also cleared. By default only the current + version of the ACL is cleared (the one being matched against). However it is + possible to specify another version using '@' followed by this version. + +clear map [@] + Remove all entries from the map . is the # or the + returned by "show map". Note that if the reference is a file and is + shared with a acl, this acl will be also cleared. By default only the current + version of the map is cleared (the one being matched against). However it is + possible to specify another version using '@' followed by this version. + +clear table [ data. ] | [ key ] + Remove entries from the stick-table
. + + This is typically used to unblock some users complaining they have been + abusively denied access to a service, but this can also be used to clear some + stickiness entries matching a server that is going to be replaced (see "show + table" below for details). Note that sometimes, removal of an entry will be + refused because it is currently tracked by a session. Retrying a few seconds + later after the session ends is usual enough. + + In the case where no options arguments are given all entries will be removed. + + When the "data." form is used entries matching a filter applied using the + stored data (see "stick-table" in section 4.2) are removed. A stored data + type must be specified in , and this data type must be stored in the + table otherwise an error is reported. The data is compared according to + with the 64-bit integer . Operators are the same as with + the ACLs : + + - eq : match entries whose data is equal to this value + - ne : match entries whose data is not equal to this value + - le : match entries whose data is less than or equal to this value + - ge : match entries whose data is greater than or equal to this value + - lt : match entries whose data is less than this value + - gt : match entries whose data is greater than this value + + When the key form is used the entry is removed. The key must be of the + same type as the table, which currently is limited to IPv4, IPv6, integer and + string. + + Example : + $ echo "show table http_proxy" | socat stdio /tmp/sock1 + >>> # table: http_proxy, type: ip, size:204800, used:2 + >>> 0x80e6a4c: key=127.0.0.1 use=0 exp=3594729 gpc0=0 conn_rate(30000)=1 \ + bytes_out_rate(60000)=187 + >>> 0x80e6a80: key=127.0.0.2 use=0 exp=3594740 gpc0=1 conn_rate(30000)=10 \ + bytes_out_rate(60000)=191 + + $ echo "clear table http_proxy key 127.0.0.1" | socat stdio /tmp/sock1 + + $ echo "show table http_proxy" | socat stdio /tmp/sock1 + >>> # table: http_proxy, type: ip, size:204800, used:1 + >>> 0x80e6a80: key=127.0.0.2 use=0 exp=3594740 gpc0=1 conn_rate(30000)=10 \ + bytes_out_rate(60000)=191 + $ echo "clear table http_proxy data.gpc0 eq 1" | socat stdio /tmp/sock1 + $ echo "show table http_proxy" | socat stdio /tmp/sock1 + >>> # table: http_proxy, type: ip, size:204800, used:1 + +commit acl @ + Commit all changes made to version of ACL , and deletes all past + versions. is the # or the returned by "show acl". The + version number must be between "curr_ver"+1 and "next_ver" as reported in + "show acl". The contents to be committed to the ACL can be consulted with + "show acl @ " if desired. The specified version number has normally + been created with the "prepare acl" command. The replacement is atomic. It + consists in atomically updating the current version to the specified version, + which will instantly cause all entries in other versions to become invisible, + and all entries in the new version to become visible. It is also possible to + use this command to perform an atomic removal of all visible entries of an + ACL by calling "prepare acl" first then committing without adding any + entries. This command cannot be used if the reference is a file also + used as a map. In this case, the "commit map" command must be used instead. + +commit map @ + Commit all changes made to version of map , and deletes all past + versions. is the # or the returned by "show map". The + version number must be between "curr_ver"+1 and "next_ver" as reported in + "show map". The contents to be committed to the map can be consulted with + "show map @ " if desired. The specified version number has normally + been created with the "prepare map" command. The replacement is atomic. It + consists in atomically updating the current version to the specified version, + which will instantly cause all entries in other versions to become invisible, + and all entries in the new version to become visible. It is also possible to + use this command to perform an atomic removal of all visible entries of an + map by calling "prepare map" first then committing without adding any + entries. + +commit ssl ca-file + Commit a temporary SSL CA file update transaction. + + In the case of an existing CA file (in a "Used" state in "show ssl ca-file"), + the new CA file tree entry is inserted in the CA file tree and every instance + that used the CA file entry is rebuilt, along with the SSL contexts it needs. + All the contexts previously used by the rebuilt instances are removed. + Upon success, the previous CA file entry is removed from the tree. + Upon failure, nothing is removed or deleted, and all the original SSL + contexts are kept and used. + Once the temporary transaction is committed, it is destroyed. + + In the case of a new CA file (after a "new ssl ca-file" and in a "Unused" + state in "show ssl ca-file"), the CA file will be inserted in the CA file + tree but it won't be used anywhere in HAProxy. To use it and generate SSL + contexts that use it, you will need to add it to a crt-list with "add ssl + crt-list". + + See also "new ssl ca-file", "set ssl ca-file", "abort ssl ca-file" and + "add ssl crt-list". + +commit ssl cert + Commit a temporary SSL certificate update transaction. + + In the case of an existing certificate (in a "Used" state in "show ssl + cert"), generate every SSL contextes and SNIs it need, insert them, and + remove the previous ones. Replace in memory the previous SSL certificates + everywhere the was used in the configuration. Upon failure it + doesn't remove or insert anything. Once the temporary transaction is + committed, it is destroyed. + + In the case of a new certificate (after a "new ssl cert" and in a "Unused" + state in "show ssl cert"), the certificate will be committed in a certificate + storage, but it won't be used anywhere in haproxy. To use it and generate + its SNIs you will need to add it to a crt-list or a directory with "add ssl + crt-list". + + See also "new ssl cert", "set ssl cert", "abort ssl cert" and + "add ssl crt-list". + +commit ssl crl-file + Commit a temporary SSL CRL file update transaction. + + In the case of an existing CRL file (in a "Used" state in "show ssl + crl-file"), the new CRL file entry is inserted in the CA file tree (which + holds both the CA files and the CRL files) and every instance that used the + CRL file entry is rebuilt, along with the SSL contexts it needs. + All the contexts previously used by the rebuilt instances are removed. + Upon success, the previous CRL file entry is removed from the tree. + Upon failure, nothing is removed or deleted, and all the original SSL + contexts are kept and used. + Once the temporary transaction is committed, it is destroyed. + + In the case of a new CRL file (after a "new ssl crl-file" and in a "Unused" + state in "show ssl crl-file"), the CRL file will be inserted in the CRL file + tree but it won't be used anywhere in HAProxy. To use it and generate SSL + contexts that use it, you will need to add it to a crt-list with "add ssl + crt-list". + + See also "new ssl crl-file", "set ssl crl-file", "abort ssl crl-file" and + "add ssl crt-list". + +debug dev [args]* + Call a developer-specific command. Only supported on a CLI connection running + in expert mode (see "expert-mode on"). Such commands are extremely dangerous + and not forgiving, any misuse may result in a crash of the process. They are + intended for experts only, and must really not be used unless told to do so. + Some of them are only available when haproxy is built with DEBUG_DEV defined + because they may have security implications. All of these commands require + admin privileges, and are purposely not documented to avoid encouraging their + use by people who are not at ease with the source code. + +del acl [|#] + Delete all the acl entries from the acl corresponding to the key . + is the # or the returned by "show acl". If the is used, + this command delete only the listed reference. The reference can be found with + listing the content of the acl. Note that if the reference is a file and + is shared with a map, the entry will be also deleted in the map. + +del map [|#] + Delete all the map entries from the map corresponding to the key . + is the # or the returned by "show map". If the is used, + this command delete only the listed reference. The reference can be found with + listing the content of the map. Note that if the reference is a file and + is shared with a acl, the entry will be also deleted in the map. + +del ssl ca-file + Delete a CA file tree entry from HAProxy. The CA file must be unused and + removed from any crt-list. "show ssl ca-file" displays the status of the CA + files. The deletion doesn't work with a certificate referenced directly with + the "ca-file" or "ca-verify-file" directives in the configuration. + +del ssl cert + Delete a certificate store from HAProxy. The certificate must be unused and + removed from any crt-list or directory. "show ssl cert" displays the status + of the certificate. The deletion doesn't work with a certificate referenced + directly with the "crt" directive in the configuration. + +del ssl crl-file + Delete a CRL file tree entry from HAProxy. The CRL file must be unused and + removed from any crt-list. "show ssl crl-file" displays the status of the CRL + files. The deletion doesn't work with a certificate referenced directly with + the "crl-file" directive in the configuration. + +del ssl crt-list + Delete an entry in a crt-list. This will delete every SNIs used for this + entry in the frontends. If a certificate is used several time in a crt-list, + you will need to provide which line you want to delete. To display the line + numbers, use "show ssl crt-list -n ". + +del server / + Remove a server attached to the backend . All servers are eligible, + except servers which are referenced by other configuration elements. The + server must be put in maintenance mode prior to its deletion. The operation + is cancelled if the serveur still has active or idle connection or its + connection queue is not empty. + +disable agent / + Mark the auxiliary agent check as temporarily stopped. + + In the case where an agent check is being run as a auxiliary check, due + to the agent-check parameter of a server directive, new checks are only + initialized when the agent is in the enabled. Thus, disable agent will + prevent any new agent checks from begin initiated until the agent + re-enabled using enable agent. + + When an agent is disabled the processing of an auxiliary agent check that + was initiated while the agent was set as enabled is as follows: All + results that would alter the weight, specifically "drain" or a weight + returned by the agent, are ignored. The processing of agent check is + otherwise unchanged. + + The motivation for this feature is to allow the weight changing effects + of the agent checks to be paused to allow the weight of a server to be + configured using set weight without being overridden by the agent. + + This command is restricted and can only be issued on sockets configured for + level "admin". + +disable dynamic-cookie backend + Disable the generation of dynamic cookies for the backend + +disable frontend + Mark the frontend as temporarily stopped. This corresponds to the mode which + is used during a soft restart : the frontend releases the port but can be + enabled again if needed. This should be used with care as some non-Linux OSes + are unable to enable it back. This is intended to be used in environments + where stopping a proxy is not even imaginable but a misconfigured proxy must + be fixed. That way it's possible to release the port and bind it into another + process to restore operations. The frontend will appear with status "STOP" + on the stats page. + + The frontend may be specified either by its name or by its numeric ID, + prefixed with a sharp ('#'). + + This command is restricted and can only be issued on sockets configured for + level "admin". + +disable health / + Mark the primary health check as temporarily stopped. This will disable + sending of health checks, and the last health check result will be ignored. + The server will be in unchecked state and considered UP unless an auxiliary + agent check forces it down. + + This command is restricted and can only be issued on sockets configured for + level "admin". + +disable server / + Mark the server DOWN for maintenance. In this mode, no more checks will be + performed on the server until it leaves maintenance. + If the server is tracked by other servers, those servers will be set to DOWN + during the maintenance. + + In the statistics page, a server DOWN for maintenance will appear with a + "MAINT" status, its tracking servers with the "MAINT(via)" one. + + Both the backend and the server may be specified either by their name or by + their numeric ID, prefixed with a sharp ('#'). + + This command is restricted and can only be issued on sockets configured for + level "admin". + +enable agent / + Resume auxiliary agent check that was temporarily stopped. + + See "disable agent" for details of the effect of temporarily starting + and stopping an auxiliary agent. + + This command is restricted and can only be issued on sockets configured for + level "admin". + +enable dynamic-cookie backend + Enable the generation of dynamic cookies for the backend . + A secret key must also be provided. + +enable frontend + Resume a frontend which was temporarily stopped. It is possible that some of + the listening ports won't be able to bind anymore (eg: if another process + took them since the 'disable frontend' operation). If this happens, an error + is displayed. Some operating systems might not be able to resume a frontend + which was disabled. + + The frontend may be specified either by its name or by its numeric ID, + prefixed with a sharp ('#'). + + This command is restricted and can only be issued on sockets configured for + level "admin". + +enable health / + Resume a primary health check that was temporarily stopped. This will enable + sending of health checks again. Please see "disable health" for details. + + This command is restricted and can only be issued on sockets configured for + level "admin". + +enable server / + If the server was previously marked as DOWN for maintenance, this marks the + server UP and checks are re-enabled. + + Both the backend and the server may be specified either by their name or by + their numeric ID, prefixed with a sharp ('#'). + + This command is restricted and can only be issued on sockets configured for + level "admin". + +experimental-mode [on|off] + Without options, this indicates whether the experimental mode is enabled or + disabled on the current connection. When passed "on", it turns the + experimental mode on for the current CLI connection only. With "off" it turns + it off. + + The experimental mode is used to access to extra features still in + development. These features are currently not stable and should be used with + care. They may be subject to breaking changes across versions. + + When used from the master CLI, this command shouldn't be prefixed, as it will + set the mode for any worker when connecting to its CLI. + + Example: + echo "@1; experimental-mode on; ..." | socat /var/run/haproxy.master - + echo "experimental-mode on; @1 ..." | socat /var/run/haproxy.master - + +expert-mode [on|off] + This command is similar to experimental-mode but is used to toggle the + expert mode. + + The expert mode enables displaying of expert commands that can be extremely + dangerous for the process and which may occasionally help developers collect + important information about complex bugs. Any misuse of these features will + likely lead to a process crash. Do not use this option without being invited + to do so. Note that this command is purposely not listed in the help message. + This command is only accessible in admin level. Changing to another level + automatically resets the expert mode. + + When used from the master CLI, this command shouldn't be prefixed, as it will + set the mode for any worker when connecting to its CLI. + + Example: + echo "@1; expert-mode on; debug dev exit 1" | socat /var/run/haproxy.master - + echo "expert-mode on; @1 debug dev exit 1" | socat /var/run/haproxy.master - + +get map +get acl + Lookup the value in the map or in the ACL . or + are the # or the returned by "show map" or "show acl". This command + returns all the matching patterns associated with this map. This is useful for + debugging maps and ACLs. The output format is composed by one line par + matching type. Each line is composed by space-delimited series of words. + + The first two words are: + + : The match method applied. It can be "found", "bool", + "int", "ip", "bin", "len", "str", "beg", "sub", "dir", + "dom", "end" or "reg". + + : The result. Can be "match" or "no-match". + + The following words are returned only if the pattern matches an entry. + + : "tree" or "list". The internal lookup algorithm. + + : "case-insensitive" or "case-sensitive". The + interpretation of the case. + + : match="". Return the matched pattern. It is + useful with regular expressions. + + The two last word are used to show the returned value and its type. With the + "acl" case, the pattern doesn't exist. + + return=nothing: No return because there are no "map". + return="": The value returned in the string format. + return=cannot-display: The value cannot be converted as string. + + type="": The type of the returned sample. + +get var + Show the existence, type and contents of the process-wide variable 'name'. + Only process-wide variables are readable, so the name must begin with + 'proc.' otherwise no variable will be found. This command requires levels + "operator" or "admin". + +get weight / + Report the current weight and the initial weight of server in + backend or an error if either doesn't exist. The initial weight is + the one that appears in the configuration file. Both are normally equal + unless the current weight has been changed. Both the backend and the server + may be specified either by their name or by their numeric ID, prefixed with a + sharp ('#'). + +help [] + Print the list of known keywords and their basic usage, or commands matching + the requested one. The same help screen is also displayed for unknown + commands. + +httpclient + Launch an HTTP client request and print the response on the CLI. Only + supported on a CLI connection running in expert mode (see "expert-mode on"). + It's only meant for debugging. The httpclient is able to resolve a server + name in the URL using the "default" resolvers section, which is populated + with the DNS servers of your /etc/resolv.conf by default. However it won't be + able to resolve an host from /etc/hosts if you don't use a local dns daemon + which can resolve those. + +new ssl ca-file + Create a new empty CA file tree entry to be filled with a set of CA + certificates and added to a crt-list. This command should be used in + combination with "set ssl ca-file" and "add ssl crt-list". + +new ssl cert + Create a new empty SSL certificate store to be filled with a certificate and + added to a directory or a crt-list. This command should be used in + combination with "set ssl cert" and "add ssl crt-list". + +new ssl crl-file + Create a new empty CRL file tree entry to be filled with a set of CRLs + and added to a crt-list. This command should be used in combination with "set + ssl crl-file" and "add ssl crt-list". + +prepare acl + Allocate a new version number in ACL for atomic replacement. is + the # or the returned by "show acl". The new version number is + shown in response after "New version created:". This number will then be + usable to prepare additions of new entries into the ACL which will then + atomically replace the current ones once committed. It is reported as + "next_ver" in "show acl". There is no impact of allocating new versions, as + unused versions will automatically be removed once a more recent version is + committed. Version numbers are unsigned 32-bit values which wrap at the end, + so care must be taken when comparing them in an external program. This + command cannot be used if the reference is a file also used as a map. + In this case, the "prepare map" command must be used instead. + +prepare map + Allocate a new version number in map for atomic replacement. is + the # or the returned by "show map". The new version number is + shown in response after "New version created:". This number will then be + usable to prepare additions of new entries into the map which will then + atomically replace the current ones once committed. It is reported as + "next_ver" in "show map". There is no impact of allocating new versions, as + unused versions will automatically be removed once a more recent version is + committed. Version numbers are unsigned 32-bit values which wrap at the end, + so care must be taken when comparing them in an external program. + +prompt + Toggle the prompt at the beginning of the line and enter or leave interactive + mode. In interactive mode, the connection is not closed after a command + completes. Instead, the prompt will appear again, indicating the user that + the interpreter is waiting for a new command. The prompt consists in a right + angle bracket followed by a space "> ". This mode is particularly convenient + when one wants to periodically check information such as stats or errors. + It is also a good idea to enter interactive mode before issuing a "help" + command. + +quit + Close the connection when in interactive mode. + +set dynamic-cookie-key backend + Modify the secret key used to generate the dynamic persistent cookies. + This will break the existing sessions. + +set map [|#] + Modify the value corresponding to each key in a map . is the + # or returned by "show map". If the is used in place of + , only the entry pointed by is changed. The new value is . + +set maxconn frontend + Dynamically change the specified frontend's maxconn setting. Any positive + value is allowed including zero, but setting values larger than the global + maxconn does not make much sense. If the limit is increased and connections + were pending, they will immediately be accepted. If it is lowered to a value + below the current number of connections, new connections acceptation will be + delayed until the threshold is reached. The frontend might be specified by + either its name or its numeric ID prefixed with a sharp ('#'). + +set maxconn server + Dynamically change the specified server's maxconn setting. Any positive + value is allowed including zero, but setting values larger than the global + maxconn does not make much sense. + +set maxconn global + Dynamically change the global maxconn setting within the range defined by the + initial global maxconn setting. If it is increased and connections were + pending, they will immediately be accepted. If it is lowered to a value below + the current number of connections, new connections acceptation will be + delayed until the threshold is reached. A value of zero restores the initial + setting. + +set profiling { tasks | memory } { auto | on | off } + Enables or disables CPU or memory profiling for the indicated subsystem. This + is equivalent to setting or clearing the "profiling" settings in the "global" + section of the configuration file. Please also see "show profiling". Note + that manually setting the tasks profiling to "on" automatically resets the + scheduler statistics, thus allows to check activity over a given interval. + The memory profiling is limited to certain operating systems (known to work + on the linux-glibc target), and requires USE_MEMORY_PROFILING to be set at + compile time. + +set rate-limit connections global + Change the process-wide connection rate limit, which is set by the global + 'maxconnrate' setting. A value of zero disables the limitation. This limit + applies to all frontends and the change has an immediate effect. The value + is passed in number of connections per second. + +set rate-limit http-compression global + Change the maximum input compression rate, which is set by the global + 'maxcomprate' setting. A value of zero disables the limitation. The value is + passed in number of kilobytes per second. The value is available in the "show + info" on the line "CompressBpsRateLim" in bytes. + +set rate-limit sessions global + Change the process-wide session rate limit, which is set by the global + 'maxsessrate' setting. A value of zero disables the limitation. This limit + applies to all frontends and the change has an immediate effect. The value + is passed in number of sessions per second. + +set rate-limit ssl-sessions global + Change the process-wide SSL session rate limit, which is set by the global + 'maxsslrate' setting. A value of zero disables the limitation. This limit + applies to all frontends and the change has an immediate effect. The value + is passed in number of sessions per second sent to the SSL stack. It applies + before the handshake in order to protect the stack against handshake abuses. + +set server / addr [port ] + Replace the current IP address of a server by the one provided. + Optionally, the port can be changed using the 'port' parameter. + Note that changing the port also support switching from/to port mapping + (notation with +X or -Y), only if a port is configured for the health check. + +set server / agent [ up | down ] + Force a server's agent to a new state. This can be useful to immediately + switch a server's state regardless of some slow agent checks for example. + Note that the change is propagated to tracking servers if any. + +set server / agent-addr [port ] + Change addr for servers agent checks. Allows to migrate agent-checks to + another address at runtime. You can specify both IP and hostname, it will be + resolved. + Optionally, change the port agent. + +set server / agent-port + Change the port used for agent checks. + +set server / agent-send + Change agent string sent to agent check target. Allows to update string while + changing server address to keep those two matching. + +set server / health [ up | stopping | down ] + Force a server's health to a new state. This can be useful to immediately + switch a server's state regardless of some slow health checks for example. + Note that the change is propagated to tracking servers if any. + +set server / check-addr [port ] + Change the IP address used for server health checks. + Optionally, change the port used for server health checks. + +set server / check-port + Change the port used for health checking to + +set server / state [ ready | drain | maint ] + Force a server's administrative state to a new state. This can be useful to + disable load balancing and/or any traffic to a server. Setting the state to + "ready" puts the server in normal mode, and the command is the equivalent of + the "enable server" command. Setting the state to "maint" disables any traffic + to the server as well as any health checks. This is the equivalent of the + "disable server" command. Setting the mode to "drain" only removes the server + from load balancing but still allows it to be checked and to accept new + persistent connections. Changes are propagated to tracking servers if any. + +set server / weight [%] + Change a server's weight to the value passed in argument. This is the exact + equivalent of the "set weight" command below. + +set server / fqdn + Change a server's FQDN to the value passed in argument. This requires the + internal run-time DNS resolver to be configured and enabled for this server. + +set server / ssl [ on | off ] (deprecated) + This option configures SSL ciphering on outgoing connections to the server. + When switch off, all traffic becomes plain text; health check path is not + changed. + + This command is deprecated, create a new server dynamically with or without + SSL instead, using the "add server" command. + +set severity-output [ none | number | string ] + Change the severity output format of the stats socket connected to for the + duration of the current session. + +set ssl ca-file + This command is part of a transaction system, the "commit ssl ca-file" and + "abort ssl ca-file" commands could be required. + If there is no on-going transaction, it will create a CA file tree entry into + which the certificates contained in the payload will be stored. The CA file + entry will not be stored in the CA file tree and will only be kept in a + temporary transaction. If a transaction with the same filename already exists, + the previous CA file entry will be deleted and replaced by the new one. + Once the modifications are done, you have to commit the transaction through + a "commit ssl ca-file" call. + + Example: + echo -e "set ssl ca-file cafile.pem <<\n$(cat rootCA.crt)\n" | \ + socat /var/run/haproxy.stat - + echo "commit ssl ca-file cafile.pem" | socat /var/run/haproxy.stat - + +set ssl cert + This command is part of a transaction system, the "commit ssl cert" and + "abort ssl cert" commands could be required. + This whole transaction system works on any certificate displayed by the + "show ssl cert" command, so on any frontend or backend certificate. + If there is no on-going transaction, it will duplicate the certificate + in memory to a temporary transaction, then update this + transaction with the PEM file in the payload. If a transaction exists with + the same filename, it will update this transaction. It's also possible to + update the files linked to a certificate (.issuer, .sctl, .oscp etc.) + Once the modification are done, you have to "commit ssl cert" the + transaction. + + Injection of files over the CLI must be done with caution since an empty line + is used to notify the end of the payload. It is recommended to inject a PEM + file which has been sanitized. A simple method would be to remove every empty + line and only leave what are in the PEM sections. It could be achieved with a + sed command. + + Example: + + # With some simple sanitizing + echo -e "set ssl cert localhost.pem <<\n$(sed -n '/^$/d;/-BEGIN/,/-END/p' 127.0.0.1.pem)\n" | \ + socat /var/run/haproxy.stat - + + # Complete example with commit + echo -e "set ssl cert localhost.pem <<\n$(cat 127.0.0.1.pem)\n" | \ + socat /var/run/haproxy.stat - + echo -e \ + "set ssl cert localhost.pem.issuer <<\n $(cat 127.0.0.1.pem.issuer)\n" | \ + socat /var/run/haproxy.stat - + echo -e \ + "set ssl cert localhost.pem.ocsp <<\n$(base64 -w 1000 127.0.0.1.pem.ocsp)\n" | \ + socat /var/run/haproxy.stat - + echo "commit ssl cert localhost.pem" | socat /var/run/haproxy.stat - + +set ssl crl-file + This command is part of a transaction system, the "commit ssl crl-file" and + "abort ssl crl-file" commands could be required. + If there is no on-going transaction, it will create a CRL file tree entry into + which the Revocation Lists contained in the payload will be stored. The CRL + file entry will not be stored in the CRL file tree and will only be kept in a + temporary transaction. If a transaction with the same filename already exists, + the previous CRL file entry will be deleted and replaced by the new one. + Once the modifications are done, you have to commit the transaction through + a "commit ssl crl-file" call. + + Example: + echo -e "set ssl crl-file crlfile.pem <<\n$(cat rootCRL.pem)\n" | \ + socat /var/run/haproxy.stat - + echo "commit ssl crl-file crlfile.pem" | socat /var/run/haproxy.stat - + +set ssl ocsp-response + This command is used to update an OCSP Response for a certificate (see "crt" + on "bind" lines). Same controls are performed as during the initial loading of + the response. The must be passed as a base64 encoded string of the + DER encoded response from the OCSP server. This command is not supported with + BoringSSL. + + Example: + openssl ocsp -issuer issuer.pem -cert server.pem \ + -host ocsp.issuer.com:80 -respout resp.der + echo "set ssl ocsp-response $(base64 -w 10000 resp.der)" | \ + socat stdio /var/run/haproxy.stat + + using the payload syntax: + echo -e "set ssl ocsp-response <<\n$(base64 resp.der)\n" | \ + socat stdio /var/run/haproxy.stat + +set ssl tls-key + Set the next TLS key for the listener to . This key becomes the + ultimate key, while the penultimate one is used for encryption (others just + decrypt). The oldest TLS key present is overwritten. is either a numeric + # or returned by "show tls-keys". is a base64 encoded 48 + or 80 bits TLS ticket key (ex. openssl rand 80 | openssl base64 -A). + +set table
key [data. ]* + Create or update a stick-table entry in the table. If the key is not present, + an entry is inserted. See stick-table in section 4.2 to find all possible + values for . The most likely use consists in dynamically entering + entries for source IP addresses, with a flag in gpc0 to dynamically block an + IP address or affect its quality of service. It is possible to pass multiple + data_types in a single call. + +set timeout cli + Change the CLI interface timeout for current connection. This can be useful + during long debugging sessions where the user needs to constantly inspect + some indicators without being disconnected. The delay is passed in seconds. + +set var +set var expr +set var fmt + Allows to set or overwrite the process-wide variable 'name' with the result + of expression or format string . Only process-wide + variables may be used, so the name must begin with 'proc.' otherwise no + variable will be set. The and may only involve + "internal" sample fetch keywords and converters even though the most likely + useful ones will be str('something'), int(), simple strings or references to + other variables. Note that the command line parser doesn't know about quotes, + so any space in the expression must be preceded by a backslash. This command + requires levels "operator" or "admin". This command is only supported on a + CLI connection running in experimental mode (see "experimental-mode on"). + +set weight / [%] + Change a server's weight to the value passed in argument. If the value ends + with the '%' sign, then the new weight will be relative to the initially + configured weight. Absolute weights are permitted between 0 and 256. + Relative weights must be positive with the resulting absolute weight is + capped at 256. Servers which are part of a farm running a static + load-balancing algorithm have stricter limitations because the weight + cannot change once set. Thus for these servers, the only accepted values + are 0 and 100% (or 0 and the initial weight). Changes take effect + immediately, though certain LB algorithms require a certain amount of + requests to consider changes. A typical usage of this command is to + disable a server during an update by setting its weight to zero, then to + enable it again after the update by setting it back to 100%. This command + is restricted and can only be issued on sockets configured for level + "admin". Both the backend and the server may be specified either by their + name or by their numeric ID, prefixed with a sharp ('#'). + +show acl [[@] ] + Dump info about acl converters. Without argument, the list of all available + acls is returned. If a is specified, its contents are dumped. is + the # or . By default the current version of the ACL is shown (the + version currently being matched against and reported as 'curr_ver' in the ACL + list). It is possible to instead dump other versions by prepending '@' + before the ACL's identifier. The version works as a filter and non-existing + versions will simply report no result. The dump format is the same as for the + maps even for the sample values. The data returned are not a list of + available ACL, but are the list of all patterns composing any ACL. Many of + these patterns can be shared with maps. The 'entry_cnt' value represents the + count of all the ACL entries, not just the active ones, which means that it + also includes entries currently being added. + +show backend + Dump the list of backends available in the running process + +show cli level + Display the CLI level of the current CLI session. The result could be + 'admin', 'operator' or 'user'. See also the 'operator' and 'user' commands. + + Example : + + $ socat /tmp/sock1 readline + prompt + > operator + > show cli level + operator + > user + > show cli level + user + > operator + Permission denied + +operator + Decrease the CLI level of the current CLI session to operator. It can't be + increased. It also drops expert and experimental mode. See also "show cli + level". + +user + Decrease the CLI level of the current CLI session to user. It can't be + increased. It also drops expert and experimental mode. See also "show cli + level". + +show activity + Reports some counters about internal events that will help developers and + more generally people who know haproxy well enough to narrow down the causes + of reports of abnormal behaviours. A typical example would be a properly + running process never sleeping and eating 100% of the CPU. The output fields + will be made of one line per metric, and per-thread counters on the same + line. These counters are 32-bit and will wrap during the process's life, which + is not a problem since calls to this command will typically be performed + twice. The fields are purposely not documented so that their exact meaning is + verified in the code where the counters are fed. These values are also reset + by the "clear counters" command. + +show cli sockets + List CLI sockets. The output format is composed of 3 fields separated by + spaces. The first field is the socket address, it can be a unix socket, a + ipv4 address:port couple or a ipv6 one. Socket of other types won't be dump. + The second field describe the level of the socket: 'admin', 'user' or + 'operator'. The last field list the processes on which the socket is bound, + separated by commas, it can be numbers or 'all'. + + Example : + + $ echo 'show cli sockets' | socat stdio /tmp/sock1 + # socket lvl processes + /tmp/sock1 admin all + 127.0.0.1:9999 user 2,3,4 + 127.0.0.2:9969 user 2 + [::1]:9999 operator 2 + +show cache + List the configured caches and the objects stored in each cache tree. + + $ echo 'show cache' | socat stdio /tmp/sock1 + 0x7f6ac6c5b03a: foobar (shctx:0x7f6ac6c5b000, available blocks:3918) + 1 2 3 4 + + 1. pointer to the cache structure + 2. cache name + 3. pointer to the mmap area (shctx) + 4. number of blocks available for reuse in the shctx + + 0x7f6ac6c5b4cc hash:286881868 vary:0x0011223344556677 size:39114 (39 blocks), refcount:9, expire:237 + 1 2 3 4 5 6 7 + + 1. pointer to the cache entry + 2. first 32 bits of the hash + 3. secondary hash of the entry in case of vary + 4. size of the object in bytes + 5. number of blocks used for the object + 6. number of transactions using the entry + 7. expiration time, can be negative if already expired + +show env [] + Dump one or all environment variables known by the process. Without any + argument, all variables are dumped. With an argument, only the specified + variable is dumped if it exists. Otherwise "Variable not found" is emitted. + Variables are dumped in the same format as they are stored or returned by the + "env" utility, that is, "=". This can be handy when debugging + certain configuration files making heavy use of environment variables to + ensure that they contain the expected values. This command is restricted and + can only be issued on sockets configured for levels "operator" or "admin". + +show errors [|] [request|response] + Dump last known request and response errors collected by frontends and + backends. If is specified, the limit the dump to errors concerning + either frontend or backend whose ID is . Proxy ID "-1" will cause + all instances to be dumped. If a proxy name is specified instead, its ID + will be used as the filter. If "request" or "response" is added after the + proxy name or ID, only request or response errors will be dumped. This + command is restricted and can only be issued on sockets configured for + levels "operator" or "admin". + + The errors which may be collected are the last request and response errors + caused by protocol violations, often due to invalid characters in header + names. The report precisely indicates what exact character violated the + protocol. Other important information such as the exact date the error was + detected, frontend and backend names, the server name (when known), the + internal session ID and the source address which has initiated the session + are reported too. + + All characters are returned, and non-printable characters are encoded. The + most common ones (\t = 9, \n = 10, \r = 13 and \e = 27) are encoded as one + letter following a backslash. The backslash itself is encoded as '\\' to + avoid confusion. Other non-printable characters are encoded '\xNN' where + NN is the two-digits hexadecimal representation of the character's ASCII + code. + + Lines are prefixed with the position of their first character, starting at 0 + for the beginning of the buffer. At most one input line is printed per line, + and large lines will be broken into multiple consecutive output lines so that + the output never goes beyond 79 characters wide. It is easy to detect if a + line was broken, because it will not end with '\n' and the next line's offset + will be followed by a '+' sign, indicating it is a continuation of previous + line. + + Example : + $ echo "show errors -1 response" | socat stdio /tmp/sock1 + >>> [04/Mar/2009:15:46:56.081] backend http-in (#2) : invalid response + src 127.0.0.1, session #54, frontend fe-eth0 (#1), server s2 (#1) + response length 213 bytes, error at position 23: + + 00000 HTTP/1.0 200 OK\r\n + 00017 header/bizarre:blah\r\n + 00038 Location: blah\r\n + 00054 Long-line: this is a very long line which should b + 00104+ e broken into multiple lines on the output buffer, + 00154+ otherwise it would be too large to print in a ter + 00204+ minal\r\n + 00211 \r\n + + In the example above, we see that the backend "http-in" which has internal + ID 2 has blocked an invalid response from its server s2 which has internal + ID 1. The request was on session 54 initiated by source 127.0.0.1 and + received by frontend fe-eth0 whose ID is 1. The total response length was + 213 bytes when the error was detected, and the error was at byte 23. This + is the slash ('/') in header name "header/bizarre", which is not a valid + HTTP character for a header name. + +show events [] [-w] [-n] + With no option, this lists all known event sinks and their types. With an + option, it will dump all available events in the designated sink if it is of + type buffer. If option "-w" is passed after the sink name, then once the end + of the buffer is reached, the command will wait for new events and display + them. It is possible to stop the operation by entering any input (which will + be discarded) or by closing the session. Finally, option "-n" is used to + directly seek to the end of the buffer, which is often convenient when + combined with "-w" to only report new events. For convenience, "-wn" or "-nw" + may be used to enable both options at once. + +show fd [] + Dump the list of either all open file descriptors or just the one number + if specified. This is only aimed at developers who need to observe internal + states in order to debug complex issues such as abnormal CPU usages. One fd + is reported per lines, and for each of them, its state in the poller using + upper case letters for enabled flags and lower case for disabled flags, using + "P" for "polled", "R" for "ready", "A" for "active", the events status using + "H" for "hangup", "E" for "error", "O" for "output", "P" for "priority" and + "I" for "input", a few other flags like "N" for "new" (just added into the fd + cache), "U" for "updated" (received an update in the fd cache), "L" for + "linger_risk", "C" for "cloned", then the cached entry position, the pointer + to the internal owner, the pointer to the I/O callback and its name when + known. When the owner is a connection, the connection flags, and the target + are reported (frontend, proxy or server). When the owner is a listener, the + listener's state and its frontend are reported. There is no point in using + this command without a good knowledge of the internals. It's worth noting + that the output format may evolve over time so this output must not be parsed + by tools designed to be durable. Some internal structure states may look + suspicious to the function listing them, in this case the output line will be + suffixed with an exclamation mark ('!'). This may help find a starting point + when trying to diagnose an incident. + +show info [typed|json] [desc] [float] + Dump info about haproxy status on current process. If "typed" is passed as an + optional argument, field numbers, names and types are emitted as well so that + external monitoring products can easily retrieve, possibly aggregate, then + report information found in fields they don't know. Each field is dumped on + its own line. If "json" is passed as an optional argument then + information provided by "typed" output is provided in JSON format as a + list of JSON objects. By default, the format contains only two columns + delimited by a colon (':'). The left one is the field name and the right + one is the value. It is very important to note that in typed output + format, the dump for a single object is contiguous so that there is no + need for a consumer to store everything at once. If "float" is passed as an + optional argument, some fields usually emitted as integers may switch to + floats for higher accuracy. It is purposely unspecified which ones are + concerned as this might evolve over time. Using this option implies that the + consumer is able to process floats. The output format used is sprintf("%f"). + + When using the typed output format, each line is made of 4 columns delimited + by colons (':'). The first column is a dot-delimited series of 3 elements. The + first element is the numeric position of the field in the list (starting at + zero). This position shall not change over time, but holes are to be expected, + depending on build options or if some fields are deleted in the future. The + second element is the field name as it appears in the default "show info" + output. The third element is the relative process number starting at 1. + + The rest of the line starting after the first colon follows the "typed output + format" described in the section above. In short, the second column (after the + first ':') indicates the origin, nature and scope of the variable. The third + column indicates the type of the field, among "s32", "s64", "u32", "u64" and + "str". Then the fourth column is the value itself, which the consumer knows + how to parse thanks to column 3 and how to process thanks to column 2. + + Thus the overall line format in typed mode is : + + ..::: + + When "desc" is appended to the command, one extra colon followed by a quoted + string is appended with a description for the metric. At the time of writing, + this is only supported for the "typed" and default output formats. + + Example : + + > show info + Name: HAProxy + Version: 1.7-dev1-de52ea-146 + Release_date: 2016/03/11 + Nbproc: 1 + Process_num: 1 + Pid: 28105 + Uptime: 0d 0h00m04s + Uptime_sec: 4 + Memmax_MB: 0 + PoolAlloc_MB: 0 + PoolUsed_MB: 0 + PoolFailed: 0 + (...) + + > show info typed + 0.Name.1:POS:str:HAProxy + 1.Version.1:POS:str:1.7-dev1-de52ea-146 + 2.Release_date.1:POS:str:2016/03/11 + 3.Nbproc.1:CGS:u32:1 + 4.Process_num.1:KGP:u32:1 + 5.Pid.1:SGP:u32:28105 + 6.Uptime.1:MDP:str:0d 0h00m08s + 7.Uptime_sec.1:MDP:u32:8 + 8.Memmax_MB.1:CLP:u32:0 + 9.PoolAlloc_MB.1:MGP:u32:0 + 10.PoolUsed_MB.1:MGP:u32:0 + 11.PoolFailed.1:MCP:u32:0 + (...) + + In the typed format, the presence of the process ID at the end of the + first column makes it very easy to visually aggregate outputs from + multiple processes. + Example : + + $ ( echo show info typed | socat /var/run/haproxy.sock1 ; \ + echo show info typed | socat /var/run/haproxy.sock2 ) | \ + sort -t . -k 1,1n -k 2,2 -k 3,3n + 0.Name.1:POS:str:HAProxy + 0.Name.2:POS:str:HAProxy + 1.Version.1:POS:str:1.7-dev1-868ab3-148 + 1.Version.2:POS:str:1.7-dev1-868ab3-148 + 2.Release_date.1:POS:str:2016/03/11 + 2.Release_date.2:POS:str:2016/03/11 + 3.Nbproc.1:CGS:u32:2 + 3.Nbproc.2:CGS:u32:2 + 4.Process_num.1:KGP:u32:1 + 4.Process_num.2:KGP:u32:2 + 5.Pid.1:SGP:u32:30120 + 5.Pid.2:SGP:u32:30121 + 6.Uptime.1:MDP:str:0d 0h01m28s + 6.Uptime.2:MDP:str:0d 0h01m28s + (...) + + The format of JSON output is described in a schema which may be output + using "show schema json". + + The JSON output contains no extra whitespace in order to reduce the + volume of output. For human consumption passing the output through a + pretty printer may be helpful. Example : + + $ echo "show info json" | socat /var/run/haproxy.sock stdio | \ + python -m json.tool + + The JSON output contains no extra whitespace in order to reduce the + volume of output. For human consumption passing the output through a + pretty printer may be helpful. Example : + + $ echo "show info json" | socat /var/run/haproxy.sock stdio | \ + python -m json.tool + +show libs + Dump the list of loaded shared dynamic libraries and object files, on systems + that support it. When available, for each shared object the range of virtual + addresses will be indicated, the size and the path to the object. This can be + used for example to try to estimate what library provides a function that + appears in a dump. Note that on many systems, addresses will change upon each + restart (address space randomization), so that this list would need to be + retrieved upon startup if it is expected to be used to analyse a core file. + This command may only be issued on sockets configured for levels "operator" + or "admin". Note that the output format may vary between operating systems, + architectures and even haproxy versions, and ought not to be relied on in + scripts. + +show map [[@] ] + Dump info about map converters. Without argument, the list of all available + maps is returned. If a is specified, its contents are dumped. is + the # or . By default the current version of the map is shown (the + version currently being matched against and reported as 'curr_ver' in the map + list). It is possible to instead dump other versions by prepending '@' + before the map's identifier. The version works as a filter and non-existing + versions will simply report no result. The 'entry_cnt' value represents the + count of all the map entries, not just the active ones, which means that it + also includes entries currently being added. + + In the output, the first column is a unique entry identifier, which is usable + as a reference for operations "del map" and "set map". The second column is + the pattern and the third column is the sample if available. The data returned + are not directly a list of available maps, but are the list of all patterns + composing any map. Many of these patterns can be shared with ACL. + +show peers [dict|-] [] + Dump info about the peers configured in "peers" sections. Without argument, + the list of the peers belonging to all the "peers" sections are listed. If + is specified, only the information about the peers belonging + to this "peers" section are dumped. When "dict" is specified before the peers + section name, the entire Tx/Rx dictionary caches will also be dumped (very + large). Passing "-" may be required to dump a peers section called "dict". + + Here are two examples of outputs where hostA, hostB and hostC peers belong to + "sharedlb" peers sections. Only hostA and hostB are connected. Only hostA has + sent data to hostB. + + $ echo "show peers" | socat - /tmp/hostA + 0x55deb0224320: [15/Apr/2019:11:28:01] id=sharedlb state=0 flags=0x3 \ + resync_timeout= task_calls=45122 + 0x55deb022b540: id=hostC(remote) addr=127.0.0.12:10002 status=CONN \ + reconnect=4s confirm=0 + flags=0x0 + 0x55deb022a440: id=hostA(local) addr=127.0.0.10:10000 status=NONE \ + reconnect= confirm=0 + flags=0x0 + 0x55deb0227d70: id=hostB(remote) addr=127.0.0.11:10001 status=ESTA + reconnect=2s confirm=0 + flags=0x20000200 appctx:0x55deb028fba0 st0=7 st1=0 task_calls=14456 \ + state=EST + xprt=RAW src=127.0.0.1:37257 addr=127.0.0.10:10000 + remote_table:0x55deb0224a10 id=stkt local_id=1 remote_id=1 + last_local_table:0x55deb0224a10 id=stkt local_id=1 remote_id=1 + shared tables: + 0x55deb0224a10 local_id=1 remote_id=1 flags=0x0 remote_data=0x65 + last_acked=0 last_pushed=3 last_get=0 teaching_origin=0 update=3 + table:0x55deb022d6a0 id=stkt update=3 localupdate=3 \ + commitupdate=3 syncing=0 + + $ echo "show peers" | socat - /tmp/hostB + 0x55871b5ab320: [15/Apr/2019:11:28:03] id=sharedlb state=0 flags=0x3 \ + resync_timeout= task_calls=3 + 0x55871b5b2540: id=hostC(remote) addr=127.0.0.12:10002 status=CONN \ + reconnect=3s confirm=0 + flags=0x0 + 0x55871b5b1440: id=hostB(local) addr=127.0.0.11:10001 status=NONE \ + reconnect= confirm=0 + flags=0x0 + 0x55871b5aed70: id=hostA(remote) addr=127.0.0.10:10000 status=ESTA \ + reconnect=2s confirm=0 + flags=0x20000200 appctx:0x7fa46800ee00 st0=7 st1=0 task_calls=62356 \ + state=EST + remote_table:0x55871b5ab960 id=stkt local_id=1 remote_id=1 + last_local_table:0x55871b5ab960 id=stkt local_id=1 remote_id=1 + shared tables: + 0x55871b5ab960 local_id=1 remote_id=1 flags=0x0 remote_data=0x65 + last_acked=3 last_pushed=0 last_get=3 teaching_origin=0 update=0 + table:0x55871b5b46a0 id=stkt update=1 localupdate=0 \ + commitupdate=0 syncing=0 + +show pools + Dump the status of internal memory pools. This is useful to track memory + usage when suspecting a memory leak for example. It does exactly the same + as the SIGQUIT when running in foreground except that it does not flush + the pools. + +show profiling [{all | status | tasks | memory}] [byaddr] [] + Dumps the current profiling settings, one per line, as well as the command + needed to change them. When tasks profiling is enabled, some per-function + statistics collected by the scheduler will also be emitted, with a summary + covering the number of calls, total/avg CPU time and total/avg latency. When + memory profiling is enabled, some information such as the number of + allocations/releases and their sizes will be reported. It is possible to + limit the dump to only the profiling status, the tasks, or the memory + profiling by specifying the respective keywords; by default all profiling + information are dumped. It is also possible to limit the number of lines + of output of each category by specifying a numeric limit. If is possible to + request that the output is sorted by address instead of usage, e.g. to ease + comparisons between subsequent calls. Please note that profiling is + essentially aimed at developers since it gives hints about where CPU cycles + or memory are wasted in the code. There is nothing useful to monitor there. + +show resolvers [] + Dump statistics for the given resolvers section, or all resolvers sections + if no section is supplied. + + For each name server, the following counters are reported: + sent: number of DNS requests sent to this server + valid: number of DNS valid responses received from this server + update: number of DNS responses used to update the server's IP address + cname: number of CNAME responses + cname_error: CNAME errors encountered with this server + any_err: number of empty response (IE: server does not support ANY type) + nx: non existent domain response received from this server + timeout: how many time this server did not answer in time + refused: number of requests refused by this server + other: any other DNS errors + invalid: invalid DNS response (from a protocol point of view) + too_big: too big response + outdated: number of response arrived too late (after another name server) + +show servers conn [] + Dump the current and idle connections state of the servers belonging to the + designated backend (or all backends if none specified). A backend name or + identifier may be used. + + The output consists in a header line showing the fields titles, then one + server per line with for each, the backend name and ID, server name and ID, + the address, port and a series or values. The number of fields varies + depending on thread count. + + Given the threaded nature of idle connections, it's important to understand + that some values may change once read, and that as such, consistency within a + line isn't granted. This output is mostly provided as a debugging tool and is + not relevant to be routinely monitored nor graphed. + +show servers state [] + Dump the state of the servers found in the running configuration. A backend + name or identifier may be provided to limit the output to this backend only. + + The dump has the following format: + - first line contains the format version (1 in this specification); + - second line contains the column headers, prefixed by a sharp ('#'); + - third line and next ones contain data; + - each line starting by a sharp ('#') is considered as a comment. + + Since multiple versions of the output may co-exist, below is the list of + fields and their order per file format version : + 1: + be_id: Backend unique id. + be_name: Backend label. + srv_id: Server unique id (in the backend). + srv_name: Server label. + srv_addr: Server IP address. + srv_op_state: Server operational state (UP/DOWN/...). + 0 = SRV_ST_STOPPED + The server is down. + 1 = SRV_ST_STARTING + The server is warming up (up but + throttled). + 2 = SRV_ST_RUNNING + The server is fully up. + 3 = SRV_ST_STOPPING + The server is up but soft-stopping + (eg: 404). + srv_admin_state: Server administrative state (MAINT/DRAIN/...). + The state is actually a mask of values : + 0x01 = SRV_ADMF_FMAINT + The server was explicitly forced into + maintenance. + 0x02 = SRV_ADMF_IMAINT + The server has inherited the maintenance + status from a tracked server. + 0x04 = SRV_ADMF_CMAINT + The server is in maintenance because of + the configuration. + 0x08 = SRV_ADMF_FDRAIN + The server was explicitly forced into + drain state. + 0x10 = SRV_ADMF_IDRAIN + The server has inherited the drain status + from a tracked server. + 0x20 = SRV_ADMF_RMAINT + The server is in maintenance because of an + IP address resolution failure. + 0x40 = SRV_ADMF_HMAINT + The server FQDN was set from stats socket. + + srv_uweight: User visible server's weight. + srv_iweight: Server's initial weight. + srv_time_since_last_change: Time since last operational change. + srv_check_status: Last health check status. + srv_check_result: Last check result (FAILED/PASSED/...). + 0 = CHK_RES_UNKNOWN + Initialized to this by default. + 1 = CHK_RES_NEUTRAL + Valid check but no status information. + 2 = CHK_RES_FAILED + Check failed. + 3 = CHK_RES_PASSED + Check succeeded and server is fully up + again. + 4 = CHK_RES_CONDPASS + Check reports the server doesn't want new + sessions. + srv_check_health: Checks rise / fall current counter. + srv_check_state: State of the check (ENABLED/PAUSED/...). + The state is actually a mask of values : + 0x01 = CHK_ST_INPROGRESS + A check is currently running. + 0x02 = CHK_ST_CONFIGURED + This check is configured and may be + enabled. + 0x04 = CHK_ST_ENABLED + This check is currently administratively + enabled. + 0x08 = CHK_ST_PAUSED + Checks are paused because of maintenance + (health only). + srv_agent_state: State of the agent check (ENABLED/PAUSED/...). + This state uses the same mask values as + "srv_check_state", adding this specific one : + 0x10 = CHK_ST_AGENT + Check is an agent check (otherwise it's a + health check). + bk_f_forced_id: Flag to know if the backend ID is forced by + configuration. + srv_f_forced_id: Flag to know if the server's ID is forced by + configuration. + srv_fqdn: Server FQDN. + srv_port: Server port. + srvrecord: DNS SRV record associated to this SRV. + srv_use_ssl: use ssl for server connections. + srv_check_port: Server health check port. + srv_check_addr: Server health check address. + srv_agent_addr: Server health agent address. + srv_agent_port: Server health agent port. + +show sess + Dump all known sessions. Avoid doing this on slow connections as this can + be huge. This command is restricted and can only be issued on sockets + configured for levels "operator" or "admin". Note that on machines with + quickly recycled connections, it is possible that this output reports less + entries than really exist because it will dump all existing sessions up to + the last one that was created before the command was entered; those which + die in the mean time will not appear. + +show sess + Display a lot of internal information about the specified session identifier. + This identifier is the first field at the beginning of the lines in the dumps + of "show sess" (it corresponds to the session pointer). Those information are + useless to most users but may be used by haproxy developers to troubleshoot a + complex bug. The output format is intentionally not documented so that it can + freely evolve depending on demands. You may find a description of all fields + returned in src/dumpstats.c + + The special id "all" dumps the states of all sessions, which must be avoided + as much as possible as it is highly CPU intensive and can take a lot of time. + +show stat [domain ] [{|} ] [typed|json] \ + [desc] [up|no-maint] + Dump statistics. The domain is used to select which statistics to print; dns + and proxy are available for now. By default, the CSV format is used; you can + activate the extended typed output format described in the section above if + "typed" is passed after the other arguments; or in JSON if "json" is passed + after the other arguments. By passing , and , it is possible + to dump only selected items : + - is a proxy ID, -1 to dump everything. Alternatively, a proxy name + may be specified. In this case, this proxy's ID will be used as + the ID selector. + - selects the type of dumpable objects : 1 for frontends, 2 for + backends, 4 for servers, -1 for everything. These values can be ORed, + for example: + 1 + 2 = 3 -> frontend + backend. + 1 + 2 + 4 = 7 -> frontend + backend + server. + - is a server ID, -1 to dump everything from the selected proxy. + + Example : + $ echo "show info;show stat" | socat stdio unix-connect:/tmp/sock1 + >>> Name: HAProxy + Version: 1.4-dev2-49 + Release_date: 2009/09/23 + Nbproc: 1 + Process_num: 1 + (...) + + # pxname,svname,qcur,qmax,scur,smax,slim,stot,bin,bout,dreq, (...) + stats,FRONTEND,,,0,0,1000,0,0,0,0,0,0,,,,,OPEN,,,,,,,,,1,1,0, (...) + stats,BACKEND,0,0,0,0,1000,0,0,0,0,0,,0,0,0,0,UP,0,0,0,,0,250,(...) + (...) + www1,BACKEND,0,0,0,0,1000,0,0,0,0,0,,0,0,0,0,UP,1,1,0,,0,250, (...) + + $ + + In this example, two commands have been issued at once. That way it's easy to + find which process the stats apply to in multi-process mode. This is not + needed in the typed output format as the process number is reported on each + line. Notice the empty line after the information output which marks the end + of the first block. A similar empty line appears at the end of the second + block (stats) so that the reader knows the output has not been truncated. + + When "typed" is specified, the output format is more suitable to monitoring + tools because it provides numeric positions and indicates the type of each + output field. Each value stands on its own line with process number, element + number, nature, origin and scope. This same format is available via the HTTP + stats by passing ";typed" after the URI. It is very important to note that in + typed output format, the dump for a single object is contiguous so that there + is no need for a consumer to store everything at once. + + The "up" modifier will result in listing only servers which reportedly up or + not checked. Those down, unresolved, or in maintenance will not be listed. + This is analogous to the ";up" option on the HTTP stats. Similarly, the + "no-maint" modifier will act like the ";no-maint" HTTP modifier and will + result in disabled servers not to be listed. The difference is that those + which are enabled but down will not be evicted. + + When using the typed output format, each line is made of 4 columns delimited + by colons (':'). The first column is a dot-delimited series of 5 elements. The + first element is a letter indicating the type of the object being described. + At the moment the following object types are known : 'F' for a frontend, 'B' + for a backend, 'L' for a listener, and 'S' for a server. The second element + The second element is a positive integer representing the unique identifier of + the proxy the object belongs to. It is equivalent to the "iid" column of the + CSV output and matches the value in front of the optional "id" directive found + in the frontend or backend section. The third element is a positive integer + containing the unique object identifier inside the proxy, and corresponds to + the "sid" column of the CSV output. ID 0 is reported when dumping a frontend + or a backend. For a listener or a server, this corresponds to their respective + ID inside the proxy. The fourth element is the numeric position of the field + in the list (starting at zero). This position shall not change over time, but + holes are to be expected, depending on build options or if some fields are + deleted in the future. The fifth element is the field name as it appears in + the CSV output. The sixth element is a positive integer and is the relative + process number starting at 1. + + The rest of the line starting after the first colon follows the "typed output + format" described in the section above. In short, the second column (after the + first ':') indicates the origin, nature and scope of the variable. The third + column indicates the field type, among "s32", "s64", "u32", "u64", "flt' and + "str". Then the fourth column is the value itself, which the consumer knows + how to parse thanks to column 3 and how to process thanks to column 2. + + When "desc" is appended to the command, one extra colon followed by a quoted + string is appended with a description for the metric. At the time of writing, + this is only supported for the "typed" output format. + + Thus the overall line format in typed mode is : + + .....::: + + Here's an example of typed output format : + + $ echo "show stat typed" | socat stdio unix-connect:/tmp/sock1 + F.2.0.0.pxname.1:MGP:str:private-frontend + F.2.0.1.svname.1:MGP:str:FRONTEND + F.2.0.8.bin.1:MGP:u64:0 + F.2.0.9.bout.1:MGP:u64:0 + F.2.0.40.hrsp_2xx.1:MGP:u64:0 + L.2.1.0.pxname.1:MGP:str:private-frontend + L.2.1.1.svname.1:MGP:str:sock-1 + L.2.1.17.status.1:MGP:str:OPEN + L.2.1.73.addr.1:MGP:str:0.0.0.0:8001 + S.3.13.60.rtime.1:MCP:u32:0 + S.3.13.61.ttime.1:MCP:u32:0 + S.3.13.62.agent_status.1:MGP:str:L4TOUT + S.3.13.64.agent_duration.1:MGP:u64:2001 + S.3.13.65.check_desc.1:MCP:str:Layer4 timeout + S.3.13.66.agent_desc.1:MCP:str:Layer4 timeout + S.3.13.67.check_rise.1:MCP:u32:2 + S.3.13.68.check_fall.1:MCP:u32:3 + S.3.13.69.check_health.1:SGP:u32:0 + S.3.13.70.agent_rise.1:MaP:u32:1 + S.3.13.71.agent_fall.1:SGP:u32:1 + S.3.13.72.agent_health.1:SGP:u32:1 + S.3.13.73.addr.1:MCP:str:1.255.255.255:8888 + S.3.13.75.mode.1:MAP:str:http + B.3.0.0.pxname.1:MGP:str:private-backend + B.3.0.1.svname.1:MGP:str:BACKEND + B.3.0.2.qcur.1:MGP:u32:0 + B.3.0.3.qmax.1:MGP:u32:0 + B.3.0.4.scur.1:MGP:u32:0 + B.3.0.5.smax.1:MGP:u32:0 + B.3.0.6.slim.1:MGP:u32:1000 + B.3.0.55.lastsess.1:MMP:s32:-1 + (...) + + In the typed format, the presence of the process ID at the end of the + first column makes it very easy to visually aggregate outputs from + multiple processes, as show in the example below where each line appears + for each process : + + $ ( echo show stat typed | socat /var/run/haproxy.sock1 - ; \ + echo show stat typed | socat /var/run/haproxy.sock2 - ) | \ + sort -t . -k 1,1 -k 2,2n -k 3,3n -k 4,4n -k 5,5 -k 6,6n + B.3.0.0.pxname.1:MGP:str:private-backend + B.3.0.0.pxname.2:MGP:str:private-backend + B.3.0.1.svname.1:MGP:str:BACKEND + B.3.0.1.svname.2:MGP:str:BACKEND + B.3.0.2.qcur.1:MGP:u32:0 + B.3.0.2.qcur.2:MGP:u32:0 + B.3.0.3.qmax.1:MGP:u32:0 + B.3.0.3.qmax.2:MGP:u32:0 + B.3.0.4.scur.1:MGP:u32:0 + B.3.0.4.scur.2:MGP:u32:0 + B.3.0.5.smax.1:MGP:u32:0 + B.3.0.5.smax.2:MGP:u32:0 + B.3.0.6.slim.1:MGP:u32:1000 + B.3.0.6.slim.2:MGP:u32:1000 + (...) + + The format of JSON output is described in a schema which may be output + using "show schema json". + + The JSON output contains no extra whitespace in order to reduce the + volume of output. For human consumption passing the output through a + pretty printer may be helpful. Example : + + $ echo "show stat json" | socat /var/run/haproxy.sock stdio | \ + python -m json.tool + + The JSON output contains no extra whitespace in order to reduce the + volume of output. For human consumption passing the output through a + pretty printer may be helpful. Example : + + $ echo "show stat json" | socat /var/run/haproxy.sock stdio | \ + python -m json.tool + +show ssl ca-file [[:]] + Display the list of CA files loaded into the process and their respective + certificate counts. The certificates are not used by any frontend or backend + until their status is "Used". + A "@system-ca" entry can appear in the list, it is loaded by the httpclient + by default. It contains the list of trusted CA of your system returned by + OpenSSL. + If a filename is prefixed by an asterisk, it is a transaction which + is not committed yet. If a is specified without , it will show + the status of the CA file ("Used"/"Unused") followed by details about all the + certificates contained in the CA file. The details displayed for every + certificate are the same as the ones displayed by a "show ssl cert" command. + If a is specified followed by an , it will only display the + details of the certificate having the specified index. Indexes start from 1. + If the index is invalid (too big for instance), nothing will be displayed. + This command can be useful to check if a CA file was properly updated. + You can also display the details of an ongoing transaction by prefixing the + filename by an asterisk. + + Example : + + $ echo "show ssl ca-file" | socat /var/run/haproxy.master - + # transaction + *cafile.crt - 2 certificate(s) + # filename + cafile.crt - 1 certificate(s) + + $ echo "show ssl ca-file cafile.crt" | socat /var/run/haproxy.master - + Filename: /home/tricot/work/haproxy/reg-tests/ssl/set_cafile_ca2.crt + Status: Used + + Certificate #1: + Serial: 11A4D2200DC84376E7D233CAFF39DF44BF8D1211 + notBefore: Apr 1 07:40:53 2021 GMT + notAfter: Aug 17 07:40:53 2048 GMT + Subject Alternative Name: + Algorithm: RSA4096 + SHA1 FingerPrint: A111EF0FEFCDE11D47FE3F33ADCA8435EBEA4864 + Subject: /C=FR/ST=Some-State/O=HAProxy Technologies/CN=HAProxy Technologies CA + Issuer: /C=FR/ST=Some-State/O=HAProxy Technologies/CN=HAProxy Technologies CA + + $ echo "show ssl ca-file *cafile.crt:2" | socat /var/run/haproxy.master - + Filename: */home/tricot/work/haproxy/reg-tests/ssl/set_cafile_ca2.crt + Status: Unused + + Certificate #2: + Serial: 587A1CE5ED855040A0C82BF255FF300ADB7C8136 + [...] + +show ssl cert [] + Display the list of certificates loaded into the process. They are not used + by any frontend or backend until their status is "Used". + If a filename is prefixed by an asterisk, it is a transaction which is not + committed yet. If a filename is specified, it will show details about the + certificate. This command can be useful to check if a certificate was well + updated. You can also display details on a transaction by prefixing the + filename by an asterisk. + This command can also be used to display the details of a certificate's OCSP + response by suffixing the filename with a ".ocsp" extension. It works for + committed certificates as well as for ongoing transactions. On a committed + certificate, this command is equivalent to calling "show ssl ocsp-response" + with the certificate's corresponding OCSP response ID. + + Example : + + $ echo "@1 show ssl cert" | socat /var/run/haproxy.master - + # transaction + *test.local.pem + # filename + test.local.pem + + $ echo "@1 show ssl cert test.local.pem" | socat /var/run/haproxy.master - + Filename: test.local.pem + Status: Used + Serial: 03ECC19BA54B25E85ABA46EE561B9A10D26F + notBefore: Sep 13 21:20:24 2019 GMT + notAfter: Dec 12 21:20:24 2019 GMT + Issuer: /C=US/O=Let's Encrypt/CN=Let's Encrypt Authority X3 + Subject: /CN=test.local + Subject Alternative Name: DNS:test.local, DNS:imap.test.local + Algorithm: RSA2048 + SHA1 FingerPrint: 417A11CAE25F607B24F638B4A8AEE51D1E211477 + + $ echo "@1 show ssl cert *test.local.pem" | socat /var/run/haproxy.master - + Filename: *test.local.pem + Status: Unused + [...] + +show ssl crl-file [[:]] + Display the list of CRL files loaded into the process. They are not used + by any frontend or backend until their status is "Used". + If a filename is prefixed by an asterisk, it is a transaction which is not + committed yet. If a is specified without , it will show the + status of the CRL file ("Used"/"Unused") followed by details about all the + Revocation Lists contained in the CRL file. The details displayed for every + list are based on the output of "openssl crl -text -noout -in ". + If a is specified followed by an , it will only display the + details of the list having the specified index. Indexes start from 1. + If the index is invalid (too big for instance), nothing will be displayed. + This command can be useful to check if a CRL file was properly updated. + You can also display the details of an ongoing transaction by prefixing the + filename by an asterisk. + + Example : + + $ echo "show ssl crl-file" | socat /var/run/haproxy.master - + # transaction + *crlfile.pem + # filename + crlfile.pem + + $ echo "show ssl crl-file crlfile.pem" | socat /var/run/haproxy.master - + Filename: /home/tricot/work/haproxy/reg-tests/ssl/crlfile.pem + Status: Used + + Certificate Revocation List #1: + Version 1 + Signature Algorithm: sha256WithRSAEncryption + Issuer: /C=FR/O=HAProxy Technologies/CN=Intermediate CA2 + Last Update: Apr 23 14:45:39 2021 GMT + Next Update: Sep 8 14:45:39 2048 GMT + Revoked Certificates: + Serial Number: 1008 + Revocation Date: Apr 23 14:45:36 2021 GMT + + Certificate Revocation List #2: + Version 1 + Signature Algorithm: sha256WithRSAEncryption + Issuer: /C=FR/O=HAProxy Technologies/CN=Root CA + Last Update: Apr 23 14:30:44 2021 GMT + Next Update: Sep 8 14:30:44 2048 GMT + No Revoked Certificates. + +show ssl crt-list [-n] [] + Display the list of crt-list and directories used in the HAProxy + configuration. If a filename is specified, dump the content of a crt-list or + a directory. Once dumped the output can be used as a crt-list file. + The '-n' option can be used to display the line number, which is useful when + combined with the 'del ssl crt-list' option when a entry is duplicated. The + output with the '-n' option is not compatible with the crt-list format and + not loadable by haproxy. + + Example: + echo "show ssl crt-list -n localhost.crt-list" | socat /tmp/sock1 - + # localhost.crt-list + common.pem:1 !not.test1.com *.test1.com !localhost + common.pem:2 + ecdsa.pem:3 [verify none allow-0rtt ssl-min-ver TLSv1.0 ssl-max-ver TLSv1.3] localhost !www.test1.com + ecdsa.pem:4 [verify none allow-0rtt ssl-min-ver TLSv1.0 ssl-max-ver TLSv1.3] + +show ssl ocsp-response [] + Display the IDs of the OCSP tree entries corresponding to all the OCSP + responses used in HAProxy, as well as the issuer's name and key hash and the + serial number of the certificate for which the OCSP response was built. + If a valid is provided, display the contents of the corresponding OCSP + response. The information displayed is the same as in an "openssl ocsp -respin + -text" call. + + Example : + + $ echo "show ssl ocsp-response" | socat /var/run/haproxy.master - + # Certificate IDs + Certificate ID key : 303b300906052b0e03021a050004148a83e0060faff709ca7e9b95522a2e81635fda0a0414f652b0e435d5ea923851508f0adbe92d85de007a0202100a + Certificate ID: + Issuer Name Hash: 8A83E0060FAFF709CA7E9B95522A2E81635FDA0A + Issuer Key Hash: F652B0E435D5EA923851508F0ADBE92D85DE007A + Serial Number: 100A + + $ echo "show ssl ocsp-response 303b300906052b0e03021a050004148a83e0060faff709ca7e9b95522a2e81635fda0a0414f652b0e435d5ea923851508f0adbe92d85de007a0202100a" | socat /var/run/haproxy.master - + OCSP Response Data: + OCSP Response Status: successful (0x0) + Response Type: Basic OCSP Response + Version: 1 (0x0) + Responder Id: C = FR, O = HAProxy Technologies, CN = ocsp.haproxy.com + Produced At: May 27 15:43:38 2021 GMT + Responses: + Certificate ID: + Hash Algorithm: sha1 + Issuer Name Hash: 8A83E0060FAFF709CA7E9B95522A2E81635FDA0A + Issuer Key Hash: F652B0E435D5EA923851508F0ADBE92D85DE007A + Serial Number: 100A + Cert Status: good + This Update: May 27 15:43:38 2021 GMT + Next Update: Oct 12 15:43:38 2048 GMT + [...] + +show ssl providers + Display the names of the providers loaded by OpenSSL during init. Provider + loading can indeed be configured via the OpenSSL configuration file and this + option allows to check that the right providers were loaded. This command is + only available with OpenSSL v3. + + Example : + $ echo "show ssl providers" | socat /var/run/haproxy.master - + Loaded providers : + - fips + - base + +show startup-logs + Dump all messages emitted during the startup of the current haproxy process, + each startup-logs buffer is unique to its haproxy worker. + +show table + Dump general information on all known stick-tables. Their name is returned + (the name of the proxy which holds them), their type (currently zero, always + IP), their size in maximum possible number of entries, and the number of + entries currently in use. + + Example : + $ echo "show table" | socat stdio /tmp/sock1 + >>> # table: front_pub, type: ip, size:204800, used:171454 + >>> # table: back_rdp, type: ip, size:204800, used:0 + +show table [ data. [data. ...]] | [ key ] + Dump contents of stick-table . In this mode, a first line of generic + information about the table is reported as with "show table", then all + entries are dumped. Since this can be quite heavy, it is possible to specify + a filter in order to specify what entries to display. + + When the "data." form is used the filter applies to the stored data (see + "stick-table" in section 4.2). A stored data type must be specified + in , and this data type must be stored in the table otherwise an + error is reported. The data is compared according to with the + 64-bit integer . Operators are the same as with the ACLs : + + - eq : match entries whose data is equal to this value + - ne : match entries whose data is not equal to this value + - le : match entries whose data is less than or equal to this value + - ge : match entries whose data is greater than or equal to this value + - lt : match entries whose data is less than this value + - gt : match entries whose data is greater than this value + + In this form, you can use multiple data filter entries, up to a maximum + defined during build time (4 by default). + + When the key form is used the entry is shown. The key must be of the + same type as the table, which currently is limited to IPv4, IPv6, integer, + and string. + + Example : + $ echo "show table http_proxy" | socat stdio /tmp/sock1 + >>> # table: http_proxy, type: ip, size:204800, used:2 + >>> 0x80e6a4c: key=127.0.0.1 use=0 exp=3594729 gpc0=0 conn_rate(30000)=1 \ + bytes_out_rate(60000)=187 + >>> 0x80e6a80: key=127.0.0.2 use=0 exp=3594740 gpc0=1 conn_rate(30000)=10 \ + bytes_out_rate(60000)=191 + + $ echo "show table http_proxy data.gpc0 gt 0" | socat stdio /tmp/sock1 + >>> # table: http_proxy, type: ip, size:204800, used:2 + >>> 0x80e6a80: key=127.0.0.2 use=0 exp=3594740 gpc0=1 conn_rate(30000)=10 \ + bytes_out_rate(60000)=191 + + $ echo "show table http_proxy data.conn_rate gt 5" | \ + socat stdio /tmp/sock1 + >>> # table: http_proxy, type: ip, size:204800, used:2 + >>> 0x80e6a80: key=127.0.0.2 use=0 exp=3594740 gpc0=1 conn_rate(30000)=10 \ + bytes_out_rate(60000)=191 + + $ echo "show table http_proxy key 127.0.0.2" | \ + socat stdio /tmp/sock1 + >>> # table: http_proxy, type: ip, size:204800, used:2 + >>> 0x80e6a80: key=127.0.0.2 use=0 exp=3594740 gpc0=1 conn_rate(30000)=10 \ + bytes_out_rate(60000)=191 + + When the data criterion applies to a dynamic value dependent on time such as + a bytes rate, the value is dynamically computed during the evaluation of the + entry in order to decide whether it has to be dumped or not. This means that + such a filter could match for some time then not match anymore because as + time goes, the average event rate drops. + + It is possible to use this to extract lists of IP addresses abusing the + service, in order to monitor them or even blacklist them in a firewall. + Example : + $ echo "show table http_proxy data.gpc0 gt 0" \ + | socat stdio /tmp/sock1 \ + | fgrep 'key=' | cut -d' ' -f2 | cut -d= -f2 > abusers-ip.txt + ( or | awk '/key/{ print a[split($2,a,"=")]; }' ) + +show tasks + Dumps the number of tasks currently in the run queue, with the number of + occurrences for each function, and their average latency when it's known + (for pure tasks with task profiling enabled). The dump is a snapshot of the + instant it's done, and there may be variations depending on what tasks are + left in the queue at the moment it happens, especially in mono-thread mode + as there's less chance that I/Os can refill the queue (unless the queue is + full). This command takes exclusive access to the process and can cause + minor but measurable latencies when issued on a highly loaded process, so + it must not be abused by monitoring bots. + +show threads + Dumps some internal states and structures for each thread, that may be useful + to help developers understand a problem. The output tries to be readable by + showing one block per thread. When haproxy is built with USE_THREAD_DUMP=1, + an advanced dump mechanism involving thread signals is used so that each + thread can dump its own state in turn. Without this option, the thread + processing the command shows all its details but the other ones are less + detailed. A star ('*') is displayed in front of the thread handling the + command. A right angle bracket ('>') may also be displayed in front of + threads which didn't make any progress since last invocation of this command, + indicating a bug in the code which must absolutely be reported. When this + happens between two threads it usually indicates a deadlock. If a thread is + alone, it's a different bug like a corrupted list. In all cases the process + needs is not fully functional anymore and needs to be restarted. + + The output format is purposely not documented so that it can easily evolve as + new needs are identified, without having to maintain any form of backwards + compatibility, and just like with "show activity", the values are meaningless + without the code at hand. + +show tls-keys [id|*] + Dump all loaded TLS ticket keys references. The TLS ticket key reference ID + and the file from which the keys have been loaded is shown. Both of those + can be used to update the TLS keys using "set ssl tls-key". If an ID is + specified as parameter, it will dump the tickets, using * it will dump every + keys from every references. + +show schema json + Dump the schema used for the output of "show info json" and "show stat json". + + The contains no extra whitespace in order to reduce the volume of output. + For human consumption passing the output through a pretty printer may be + helpful. Example : + + $ echo "show schema json" | socat /var/run/haproxy.sock stdio | \ + python -m json.tool + + The schema follows "JSON Schema" (json-schema.org) and accordingly + verifiers may be used to verify the output of "show info json" and "show + stat json" against the schema. + +show trace [] + Show the current trace status. For each source a line is displayed with a + single-character status indicating if the trace is stopped, waiting, or + running. The output sink used by the trace is indicated (or "none" if none + was set), as well as the number of dropped events in this sink, followed by a + brief description of the source. If a source name is specified, a detailed + list of all events supported by the source, and their status for each action + (report, start, pause, stop), indicated by a "+" if they are enabled, or a + "-" otherwise. All these events are independent and an event might trigger + a start without being reported and conversely. + +show version + Show the version of the current HAProxy process. This is available from + master and workers CLI. + Example: + + $ echo "show version" | socat /var/run/haproxy.sock stdio + 2.4.9 + + $ echo "show version" | socat /var/run/haproxy-master.sock stdio + 2.5.0 + +shutdown frontend + Completely delete the specified frontend. All the ports it was bound to will + be released. It will not be possible to enable the frontend anymore after + this operation. This is intended to be used in environments where stopping a + proxy is not even imaginable but a misconfigured proxy must be fixed. That + way it's possible to release the port and bind it into another process to + restore operations. The frontend will not appear at all on the stats page + once it is terminated. + + The frontend may be specified either by its name or by its numeric ID, + prefixed with a sharp ('#'). + + This command is restricted and can only be issued on sockets configured for + level "admin". + +shutdown session + Immediately terminate the session matching the specified session identifier. + This identifier is the first field at the beginning of the lines in the dumps + of "show sess" (it corresponds to the session pointer). This can be used to + terminate a long-running session without waiting for a timeout or when an + endless transfer is ongoing. Such terminated sessions are reported with a 'K' + flag in the logs. + +shutdown sessions server / + Immediately terminate all the sessions attached to the specified server. This + can be used to terminate long-running sessions after a server is put into + maintenance mode, for instance. Such terminated sessions are reported with a + 'K' flag in the logs. + +trace + The "trace" command alone lists the trace sources, their current status, and + their brief descriptions. It is only meant as a menu to enter next levels, + see other "trace" commands below. + +trace 0 + Immediately stops all traces. This is made to be used as a quick solution + to terminate a debugging session or as an emergency action to be used in case + complex traces were enabled on multiple sources and impact the service. + +trace event [ [+|-|!] ] + Without argument, this will list all the events supported by the designated + source. They are prefixed with a "-" if they are not enabled, or a "+" if + they are enabled. It is important to note that a single trace may be labelled + with multiple events, and as long as any of the enabled events matches one of + the events labelled on the trace, the event will be passed to the trace + subsystem. For example, receiving an HTTP/2 frame of type HEADERS may trigger + a frame event and a stream event since the frame creates a new stream. If + either the frame event or the stream event are enabled for this source, the + frame will be passed to the trace framework. + + With an argument, it is possible to toggle the state of each event and + individually enable or disable them. Two special keywords are supported, + "none", which matches no event, and is used to disable all events at once, + and "any" which matches all events, and is used to enable all events at + once. Other events are specific to the event source. It is possible to + enable one event by specifying its name, optionally prefixed with '+' for + better readability. It is possible to disable one event by specifying its + name prefixed by a '-' or a '!'. + + One way to completely disable a trace source is to pass "event none", and + this source will instantly be totally ignored. + +trace level [] + Without argument, this will list all trace levels for this source, and the + current one will be indicated by a star ('*') prepended in front of it. With + an argument, this will change the trace level to the specified level. Detail + levels are a form of filters that are applied before reporting the events. + These filters are used to selectively include or exclude events depending on + their level of importance. For example a developer might need to know + precisely where in the code an HTTP header was considered invalid while the + end user may not even care about this header's validity at all. There are + currently 5 distinct levels for a trace : + + user this will report information that are suitable for use by a + regular haproxy user who wants to observe his traffic. + Typically some HTTP requests and responses will be reported + without much detail. Most sources will set this as the + default level to ease operations. + + proto in addition to what is reported at the "user" level, it also + displays protocol-level updates. This can for example be the + frame types or HTTP headers after decoding. + + state in addition to what is reported at the "proto" level, it + will also display state transitions (or failed transitions) + which happen in parsers, so this will show attempts to + perform an operation while the "proto" level only shows + the final operation. + + data in addition to what is reported at the "state" level, it + will also include data transfers between the various layers. + + developer it reports everything available, which can include advanced + information such as "breaking out of this loop" that are + only relevant to a developer trying to understand a bug that + only happens once in a while in field. Function names are + only reported at this level. + + It is highly recommended to always use the "user" level only and switch to + other levels only if instructed to do so by a developer. Also it is a good + idea to first configure the events before switching to higher levels, as it + may save from dumping many lines if no filter is applied. + +trace lock [criterion] + Without argument, this will list all the criteria supported by this source + for lock-on processing, and display the current choice by a star ('*') in + front of it. Lock-on means that the source will focus on the first matching + event and only stick to the criterion which triggered this event, and ignore + all other ones until the trace stops. This allows for example to take a trace + on a single connection or on a single stream. The following criteria are + supported by some traces, though not necessarily all, since some of them + might not be available to the source : + + backend lock on the backend that started the trace + connection lock on the connection that started the trace + frontend lock on the frontend that started the trace + listener lock on the listener that started the trace + nothing do not lock on anything + server lock on the server that started the trace + session lock on the session that started the trace + thread lock on the thread that started the trace + + In addition to this, each source may provide up to 4 specific criteria such + as internal states or connection IDs. For example in HTTP/2 it is possible + to lock on the H2 stream and ignore other streams once a strace starts. + + When a criterion is passed in argument, this one is used instead of the + other ones and any existing tracking is immediately terminated so that it can + restart with the new criterion. The special keyword "nothing" is supported by + all sources to permanently disable tracking. + +trace { pause | start | stop } [ [+|-|!]event] + Without argument, this will list the events enabled to automatically pause, + start, or stop a trace for this source. These events are specific to each + trace source. With an argument, this will either enable the event for the + specified action (if optionally prefixed by a '+') or disable it (if + prefixed by a '-' or '!'). The special keyword "now" is not an event and + requests to take the action immediately. The keywords "none" and "any" are + supported just like in "trace event". + + The 3 supported actions are respectively "pause", "start" and "stop". The + "pause" action enumerates events which will cause a running trace to stop and + wait for a new start event to restart it. The "start" action enumerates the + events which switch the trace into the waiting mode until one of the start + events appears. And the "stop" action enumerates the events which definitely + stop the trace until it is manually enabled again. In practice it makes sense + to manually start a trace using "start now" without caring about events, and + to stop it using "stop now". In order to capture more subtle event sequences, + setting "start" to a normal event (like receiving an HTTP request) and "stop" + to a very rare event like emitting a certain error, will ensure that the last + captured events will match the desired criteria. And the pause event is + useful to detect the end of a sequence, disable the lock-on and wait for + another opportunity to take a capture. In this case it can make sense to + enable lock-on to spot only one specific criterion (e.g. a stream), and have + "start" set to anything that starts this criterion (e.g. all events which + create a stream), "stop" set to the expected anomaly, and "pause" to anything + that ends that criterion (e.g. any end of stream event). In this case the + trace log will contain complete sequences of perfectly clean series affecting + a single object, until the last sequence containing everything from the + beginning to the anomaly. + +trace sink [] + Without argument, this will list all event sinks available for this source, + and the currently configured one will have a star ('*') prepended in front + of it. Sink "none" is always available and means that all events are simply + dropped, though their processing is not ignored (e.g. lock-on does occur). + Other sinks are available depending on configuration and build options, but + typically "stdout" and "stderr" will be usable in debug mode, and in-memory + ring buffers should be available as well. When a name is specified, the sink + instantly changes for the specified source. Events are not changed during a + sink change. In the worst case some may be lost if an invalid sink is used + (or "none"), but operations do continue to a different destination. + +trace verbosity [] + Without argument, this will list all verbosity levels for this source, and the + current one will be indicated by a star ('*') prepended in front of it. With + an argument, this will change the verbosity level to the specified one. + + Verbosity levels indicate how far the trace decoder should go to provide + detailed information. It depends on the trace source, since some sources will + not even provide a specific decoder. Level "quiet" is always available and + disables any decoding. It can be useful when trying to figure what's + happening before trying to understand the details, since it will have a very + low impact on performance and trace size. When no verbosity levels are + declared by a source, level "default" is available and will cause a decoder + to be called when specified in the traces. It is an opportunistic decoding. + When the source declares some verbosity levels, these ones are listed with + a description of what they correspond to. In this case the trace decoder + provided by the source will be as accurate as possible based on the + information available at the trace point. The first level above "quiet" is + set by default. + + +9.4. Master CLI +--------------- + +The master CLI is a socket bound to the master process in master-worker mode. +This CLI gives access to the unix socket commands in every running or leaving +processes and allows a basic supervision of those processes. + +The master CLI is configurable only from the haproxy program arguments with +the -S option. This option also takes bind options separated by commas. + +Example: + + # haproxy -W -S 127.0.0.1:1234 -f test1.cfg + # haproxy -Ws -S /tmp/master-socket,uid,1000,gid,1000,mode,600 -f test1.cfg + # haproxy -W -S /tmp/master-socket,level,user -f test1.cfg + + +9.4.1. Master CLI commands +-------------------------- + +@<[!]pid> + The master CLI uses a special prefix notation to access the multiple + processes. This notation is easily identifiable as it begins by a @. + + A @ prefix can be followed by a relative process number or by an exclamation + point and a PID. (e.g. @1 or @!1271). A @ alone could be use to specify the + master. Leaving processes are only accessible with the PID as relative process + number are only usable with the current processes. + + Examples: + + $ socat /var/run/haproxy-master.sock readline + prompt + master> @1 show info; @2 show info + [...] + Process_num: 1 + Pid: 1271 + [...] + Process_num: 2 + Pid: 1272 + [...] + master> + + $ echo '@!1271 show info; @!1272 show info' | socat /var/run/haproxy-master.sock - + [...] + + A prefix could be use as a command, which will send every next commands to + the specified process. + + Examples: + + $ socat /var/run/haproxy-master.sock readline + prompt + master> @1 + 1271> show info + [...] + 1271> show stat + [...] + 1271> @ + master> + + $ echo '@1; show info; show stat; @2; show info; show stat' | socat /var/run/haproxy-master.sock - + [...] + +expert-mode [on|off] + This command activates the "expert-mode" for every worker accessed from the + master CLI. Combined with "mcli-debug-mode" it also activates the command on + the master. Display the flag "e" in the master CLI prompt. + + See also "expert-mode" in Section 9.3 and "mcli-debug-mode" in 9.4.1. + +experimental-mode [on|off] + This command activates the "experimental-mode" for every worker accessed from + the master CLI. Combined with "mcli-debug-mode" it also activates the command on + the master. Display the flag "x" in the master CLI prompt. + + See also "experimental-mode" in Section 9.3 and "mcli-debug-mode" in 9.4.1. + +mcli-debug-mode [on|off] + This keyword allows a special mode in the master CLI which enables every + keywords that were meant for a worker CLI on the master CLI, allowing to debug + the master process. Once activated, you list the new available keywords with + "help". Combined with "experimental-mode" or "expert-mode" it enables even + more keywords. Display the flag "d" in the master CLI prompt. + +prompt + When the prompt is enabled (via the "prompt" command), the context the CLI is + working on is displayed in the prompt. The master is identified by the "master" + string, and other processes are identified with their PID. In case the last + reload failed, the master prompt will be changed to "master[ReloadFailed]>" so + that it becomes visible that the process is still running on the previous + configuration and that the new configuration is not operational. + + The prompt of the master CLI is able to display several flags which are the + enable modes. "d" for mcli-debug-mode, "e" for expert-mode, "x" for + experimental-mode. + + Example: + $ socat /var/run/haproxy-master.sock - + prompt + master> expert-mode on + master(e)> experimental-mode on + master(xe)> mcli-debug-mode on + master(xed)> @1 + 95191(xed)> + +reload + You can also reload the HAProxy master process with the "reload" command which + does the same as a `kill -USR2` on the master process, provided that the user + has at least "operator" or "admin" privileges. + + Example: + + $ echo "reload" | socat /var/run/haproxy-master.sock stdin + + Note that a reload will close the connection to the master CLI. + +show proc + The master CLI introduces a 'show proc' command to surpervise the + processe. + + Example: + + $ echo 'show proc' | socat /var/run/haproxy-master.sock - + # + 1162 master 5 [failed: 0] 0d00h02m07s 2.5-dev13 + # workers + 1271 worker 1 0d00h00m00s 2.5-dev13 + # old workers + 1233 worker 3 0d00h00m43s 2.0-dev3-6019f6-289 + # programs + 1244 foo 0 0d00h00m00s - + 1255 bar 0 0d00h00m00s - + + In this example, the master has been reloaded 5 times but one of the old + worker is still running and survived 3 reloads. You could access the CLI of + this worker to understand what's going on. + +10. Tricks for easier configuration management +---------------------------------------------- + +It is very common that two HAProxy nodes constituting a cluster share exactly +the same configuration modulo a few addresses. Instead of having to maintain a +duplicate configuration for each node, which will inevitably diverge, it is +possible to include environment variables in the configuration. Thus multiple +configuration may share the exact same file with only a few different system +wide environment variables. This started in version 1.5 where only addresses +were allowed to include environment variables, and 1.6 goes further by +supporting environment variables everywhere. The syntax is the same as in the +UNIX shell, a variable starts with a dollar sign ('$'), followed by an opening +curly brace ('{'), then the variable name followed by the closing brace ('}'). +Except for addresses, environment variables are only interpreted in arguments +surrounded with double quotes (this was necessary not to break existing setups +using regular expressions involving the dollar symbol). + +Environment variables also make it convenient to write configurations which are +expected to work on various sites where only the address changes. It can also +permit to remove passwords from some configs. Example below where the the file +"site1.env" file is sourced by the init script upon startup : + + $ cat site1.env + LISTEN=192.168.1.1 + CACHE_PFX=192.168.11 + SERVER_PFX=192.168.22 + LOGGER=192.168.33.1 + STATSLP=admin:pa$$w0rd + ABUSERS=/etc/haproxy/abuse.lst + TIMEOUT=10s + + $ cat haproxy.cfg + global + log "${LOGGER}:514" local0 + + defaults + mode http + timeout client "${TIMEOUT}" + timeout server "${TIMEOUT}" + timeout connect 5s + + frontend public + bind "${LISTEN}:80" + http-request reject if { src -f "${ABUSERS}" } + stats uri /stats + stats auth "${STATSLP}" + use_backend cache if { path_end .jpg .css .ico } + default_backend server + + backend cache + server cache1 "${CACHE_PFX}.1:18080" check + server cache2 "${CACHE_PFX}.2:18080" check + + backend server + server cache1 "${SERVER_PFX}.1:8080" check + server cache2 "${SERVER_PFX}.2:8080" check + + +11. Well-known traps to avoid +----------------------------- + +Once in a while, someone reports that after a system reboot, the haproxy +service wasn't started, and that once they start it by hand it works. Most +often, these people are running a clustered IP address mechanism such as +keepalived, to assign the service IP address to the master node only, and while +it used to work when they used to bind haproxy to address 0.0.0.0, it stopped +working after they bound it to the virtual IP address. What happens here is +that when the service starts, the virtual IP address is not yet owned by the +local node, so when HAProxy wants to bind to it, the system rejects this +because it is not a local IP address. The fix doesn't consist in delaying the +haproxy service startup (since it wouldn't stand a restart), but instead to +properly configure the system to allow binding to non-local addresses. This is +easily done on Linux by setting the net.ipv4.ip_nonlocal_bind sysctl to 1. This +is also needed in order to transparently intercept the IP traffic that passes +through HAProxy for a specific target address. + +Multi-process configurations involving source port ranges may apparently seem +to work but they will cause some random failures under high loads because more +than one process may try to use the same source port to connect to the same +server, which is not possible. The system will report an error and a retry will +happen, picking another port. A high value in the "retries" parameter may hide +the effect to a certain extent but this also comes with increased CPU usage and +processing time. Logs will also report a certain number of retries. For this +reason, port ranges should be avoided in multi-process configurations. + +Since HAProxy uses SO_REUSEPORT and supports having multiple independent +processes bound to the same IP:port, during troubleshooting it can happen that +an old process was not stopped before a new one was started. This provides +absurd test results which tend to indicate that any change to the configuration +is ignored. The reason is that in fact even the new process is restarted with a +new configuration, the old one also gets some incoming connections and +processes them, returning unexpected results. When in doubt, just stop the new +process and try again. If it still works, it very likely means that an old +process remains alive and has to be stopped. Linux's "netstat -lntp" is of good +help here. + +When adding entries to an ACL from the command line (eg: when blacklisting a +source address), it is important to keep in mind that these entries are not +synchronized to the file and that if someone reloads the configuration, these +updates will be lost. While this is often the desired effect (for blacklisting) +it may not necessarily match expectations when the change was made as a fix for +a problem. See the "add acl" action of the CLI interface. + + +12. Debugging and performance issues +------------------------------------ + +When HAProxy is started with the "-d" option, it will stay in the foreground +and will print one line per event, such as an incoming connection, the end of a +connection, and for each request or response header line seen. This debug +output is emitted before the contents are processed, so they don't consider the +local modifications. The main use is to show the request and response without +having to run a network sniffer. The output is less readable when multiple +connections are handled in parallel, though the "debug2ansi" and "debug2html" +scripts found in the examples/ directory definitely help here by coloring the +output. + +If a request or response is rejected because HAProxy finds it is malformed, the +best thing to do is to connect to the CLI and issue "show errors", which will +report the last captured faulty request and response for each frontend and +backend, with all the necessary information to indicate precisely the first +character of the input stream that was rejected. This is sometimes needed to +prove to customers or to developers that a bug is present in their code. In +this case it is often possible to relax the checks (but still keep the +captures) using "option accept-invalid-http-request" or its equivalent for +responses coming from the server "option accept-invalid-http-response". Please +see the configuration manual for more details. + +Example : + + > show errors + Total events captured on [13/Oct/2015:13:43:47.169] : 1 + + [13/Oct/2015:13:43:40.918] frontend HAProxyLocalStats (#2): invalid request + backend (#-1), server (#-1), event #0 + src 127.0.0.1:51981, session #0, session flags 0x00000080 + HTTP msg state 26, msg flags 0x00000000, tx flags 0x00000000 + HTTP chunk len 0 bytes, HTTP body len 0 bytes + buffer flags 0x00808002, out 0 bytes, total 31 bytes + pending 31 bytes, wrapping at 8040, error at position 13: + + 00000 GET /invalid request HTTP/1.1\r\n + + +The output of "show info" on the CLI provides a number of useful information +regarding the maximum connection rate ever reached, maximum SSL key rate ever +reached, and in general all information which can help to explain temporary +issues regarding CPU or memory usage. Example : + + > show info + Name: HAProxy + Version: 1.6-dev7-e32d18-17 + Release_date: 2015/10/12 + Nbproc: 1 + Process_num: 1 + Pid: 7949 + Uptime: 0d 0h02m39s + Uptime_sec: 159 + Memmax_MB: 0 + Ulimit-n: 120032 + Maxsock: 120032 + Maxconn: 60000 + Hard_maxconn: 60000 + CurrConns: 0 + CumConns: 3 + CumReq: 3 + MaxSslConns: 0 + CurrSslConns: 0 + CumSslConns: 0 + Maxpipes: 0 + PipesUsed: 0 + PipesFree: 0 + ConnRate: 0 + ConnRateLimit: 0 + MaxConnRate: 1 + SessRate: 0 + SessRateLimit: 0 + MaxSessRate: 1 + SslRate: 0 + SslRateLimit: 0 + MaxSslRate: 0 + SslFrontendKeyRate: 0 + SslFrontendMaxKeyRate: 0 + SslFrontendSessionReuse_pct: 0 + SslBackendKeyRate: 0 + SslBackendMaxKeyRate: 0 + SslCacheLookups: 0 + SslCacheMisses: 0 + CompressBpsIn: 0 + CompressBpsOut: 0 + CompressBpsRateLim: 0 + ZlibMemUsage: 0 + MaxZlibMemUsage: 0 + Tasks: 5 + Run_queue: 1 + Idle_pct: 100 + node: wtap + description: + +When an issue seems to randomly appear on a new version of HAProxy (eg: every +second request is aborted, occasional crash, etc), it is worth trying to enable +memory poisoning so that each call to malloc() is immediately followed by the +filling of the memory area with a configurable byte. By default this byte is +0x50 (ASCII for 'P'), but any other byte can be used, including zero (which +will have the same effect as a calloc() and which may make issues disappear). +Memory poisoning is enabled on the command line using the "-dM" option. It +slightly hurts performance and is not recommended for use in production. If +an issue happens all the time with it or never happens when poisoning uses +byte zero, it clearly means you've found a bug and you definitely need to +report it. Otherwise if there's no clear change, the problem it is not related. + +When debugging some latency issues, it is important to use both strace and +tcpdump on the local machine, and another tcpdump on the remote system. The +reason for this is that there are delays everywhere in the processing chain and +it is important to know which one is causing latency to know where to act. In +practice, the local tcpdump will indicate when the input data come in. Strace +will indicate when haproxy receives these data (using recv/recvfrom). Warning, +openssl uses read()/write() syscalls instead of recv()/send(). Strace will also +show when haproxy sends the data, and tcpdump will show when the system sends +these data to the interface. Then the external tcpdump will show when the data +sent are really received (since the local one only shows when the packets are +queued). The benefit of sniffing on the local system is that strace and tcpdump +will use the same reference clock. Strace should be used with "-tts200" to get +complete timestamps and report large enough chunks of data to read them. +Tcpdump should be used with "-nvvttSs0" to report full packets, real sequence +numbers and complete timestamps. + +In practice, received data are almost always immediately received by haproxy +(unless the machine has a saturated CPU or these data are invalid and not +delivered). If these data are received but not sent, it generally is because +the output buffer is saturated (ie: recipient doesn't consume the data fast +enough). This can be confirmed by seeing that the polling doesn't notify of +the ability to write on the output file descriptor for some time (it's often +easier to spot in the strace output when the data finally leave and then roll +back to see when the write event was notified). It generally matches an ACK +received from the recipient, and detected by tcpdump. Once the data are sent, +they may spend some time in the system doing nothing. Here again, the TCP +congestion window may be limited and not allow these data to leave, waiting for +an ACK to open the window. If the traffic is idle and the data take 40 ms or +200 ms to leave, it's a different issue (which is not an issue), it's the fact +that the Nagle algorithm prevents empty packets from leaving immediately, in +hope that they will be merged with subsequent data. HAProxy automatically +disables Nagle in pure TCP mode and in tunnels. However it definitely remains +enabled when forwarding an HTTP body (and this contributes to the performance +improvement there by reducing the number of packets). Some HTTP non-compliant +applications may be sensitive to the latency when delivering incomplete HTTP +response messages. In this case you will have to enable "option http-no-delay" +to disable Nagle in order to work around their design, keeping in mind that any +other proxy in the chain may similarly be impacted. If tcpdump reports that data +leave immediately but the other end doesn't see them quickly, it can mean there +is a congested WAN link, a congested LAN with flow control enabled and +preventing the data from leaving, or more commonly that HAProxy is in fact +running in a virtual machine and that for whatever reason the hypervisor has +decided that the data didn't need to be sent immediately. In virtualized +environments, latency issues are almost always caused by the virtualization +layer, so in order to save time, it's worth first comparing tcpdump in the VM +and on the external components. Any difference has to be credited to the +hypervisor and its accompanying drivers. + +When some TCP SACK segments are seen in tcpdump traces (using -vv), it always +means that the side sending them has got the proof of a lost packet. While not +seeing them doesn't mean there are no losses, seeing them definitely means the +network is lossy. Losses are normal on a network, but at a rate where SACKs are +not noticeable at the naked eye. If they appear a lot in the traces, it is +worth investigating exactly what happens and where the packets are lost. HTTP +doesn't cope well with TCP losses, which introduce huge latencies. + +The "netstat -i" command will report statistics per interface. An interface +where the Rx-Ovr counter grows indicates that the system doesn't have enough +resources to receive all incoming packets and that they're lost before being +processed by the network driver. Rx-Drp indicates that some received packets +were lost in the network stack because the application doesn't process them +fast enough. This can happen during some attacks as well. Tx-Drp means that +the output queues were full and packets had to be dropped. When using TCP it +should be very rare, but will possibly indicate a saturated outgoing link. + + +13. Security considerations +--------------------------- + +HAProxy is designed to run with very limited privileges. The standard way to +use it is to isolate it into a chroot jail and to drop its privileges to a +non-root user without any permissions inside this jail so that if any future +vulnerability were to be discovered, its compromise would not affect the rest +of the system. + +In order to perform a chroot, it first needs to be started as a root user. It is +pointless to build hand-made chroots to start the process there, these ones are +painful to build, are never properly maintained and always contain way more +bugs than the main file-system. And in case of compromise, the intruder can use +the purposely built file-system. Unfortunately many administrators confuse +"start as root" and "run as root", resulting in the uid change to be done prior +to starting haproxy, and reducing the effective security restrictions. + +HAProxy will need to be started as root in order to : + - adjust the file descriptor limits + - bind to privileged port numbers + - bind to a specific network interface + - transparently listen to a foreign address + - isolate itself inside the chroot jail + - drop to another non-privileged UID + +HAProxy may require to be run as root in order to : + - bind to an interface for outgoing connections + - bind to privileged source ports for outgoing connections + - transparently bind to a foreign address for outgoing connections + +Most users will never need the "run as root" case. But the "start as root" +covers most usages. + +A safe configuration will have : + + - a chroot statement pointing to an empty location without any access + permissions. This can be prepared this way on the UNIX command line : + + # mkdir /var/empty && chmod 0 /var/empty || echo "Failed" + + and referenced like this in the HAProxy configuration's global section : + + chroot /var/empty + + - both a uid/user and gid/group statements in the global section : + + user haproxy + group haproxy + + - a stats socket whose mode, uid and gid are set to match the user and/or + group allowed to access the CLI so that nobody may access it : + + stats socket /var/run/haproxy.stat uid hatop gid hatop mode 600 + -- cgit v1.2.3