diff options
Diffstat (limited to '')
| -rw-r--r-- | man/man8/tc-tbf.8 | 141 |
1 files changed, 141 insertions, 0 deletions
diff --git a/man/man8/tc-tbf.8 b/man/man8/tc-tbf.8 new file mode 100644 index 0000000..d721b5d --- /dev/null +++ b/man/man8/tc-tbf.8 @@ -0,0 +1,141 @@ +.TH TC 8 "13 December 2001" "iproute2" "Linux" +.SH NAME +tbf \- Token Bucket Filter +.SH SYNOPSIS +.B tc qdisc ... tbf rate +rate +.B burst +bytes/cell +.B ( latency +ms +.B | limit +bytes +.B ) [ mpu +bytes +.B [ peakrate +rate +.B mtu +bytes/cell +.B ] ] +.P +burst is also known as buffer and maxburst. mtu is also known as minburst. +.SH DESCRIPTION + +The Token Bucket Filter is a classful queueing discipline available for +traffic control with the +.BR tc (8) +command. + +TBF is a pure shaper and never schedules traffic. It is non-work-conserving and may throttle +itself, although packets are available, to ensure that the configured rate is not exceeded. +It is able to shape up to 1mbit/s of normal traffic with ideal minimal burstiness, +sending out data exactly at the configured rates. + +Much higher rates are possible but at the cost of losing the minimal burstiness. In that +case, data is on average dequeued at the configured rate but may be sent much faster at millisecond +timescales. Because of further queues living in network adaptors, this is often not a problem. + +.SH ALGORITHM +As the name implies, traffic is filtered based on the expenditure of +.B tokens. +Tokens roughly correspond to bytes, with the additional constraint +that each packet consumes some tokens, no matter how small it is. This +reflects the fact that even a zero-sized packet occupies the link for +some time. + +On creation, the TBF is stocked with tokens which correspond to the amount of traffic that can be burst +in one go. Tokens arrive at a steady rate, until the bucket is full. + +If no tokens are available, packets are queued, up to a configured limit. The TBF now +calculates the token deficit, and throttles until the first packet in the queue can be sent. + +If it is not acceptable to burst out packets at maximum speed, a peakrate can be configured +to limit the speed at which the bucket empties. This peakrate is implemented as a second TBF +with a very small bucket, so that it doesn't burst. + +To achieve perfection, the second bucket may contain only a single packet, which leads to +the earlier mentioned 1mbit/s limit. + +This limit is caused by the fact that the kernel can only throttle for at minimum 1 'jiffy', which depends +on HZ as 1/HZ. For perfect shaping, only a single packet can get sent per jiffy - for HZ=100, this means 100 +packets of on average 1000 bytes each, which roughly corresponds to 1mbit/s. + +.SH PARAMETERS +See +.BR tc (8) +for how to specify the units of these values. +.TP +limit or latency +Limit is the number of bytes that can be queued waiting for tokens to become +available. You can also specify this the other way around by setting the +latency parameter, which specifies the maximum amount of time a packet can +sit in the TBF. The latter calculation takes into account the size of the +bucket, the rate and possibly the peakrate (if set). These two parameters +are mutually exclusive. +.TP +burst +Also known as buffer or maxburst. +Size of the bucket, in bytes. This is the maximum amount of bytes that tokens can be available for instantaneously. +In general, larger shaping rates require a larger buffer. For 10mbit/s on Intel, you need at least 10kbyte buffer +if you want to reach your configured rate! + +If your buffer is too small, packets may be dropped because more tokens arrive per timer tick than fit in your bucket. +The minimum buffer size can be calculated by dividing the rate by HZ. + +Token usage calculations are performed using a table which by default has a resolution of 8 packets. +This resolution can be changed by specifying the +.B cell +size with the burst. For example, to specify a 6000 byte buffer with a 16 +byte cell size, set a burst of 6000/16. You will probably never have to set +this. Must be an integral power of 2. +.TP +mpu +A zero-sized packet does not use zero bandwidth. For ethernet, no packet uses less than 64 bytes. The Minimum Packet Unit +determines the minimal token usage (specified in bytes) for a packet. Defaults to zero. +.TP +rate +The speed knob. See remarks above about limits! See +.BR tc (8) +for units. +.PP +Furthermore, if a peakrate is desired, the following parameters are available: + +.TP +peakrate +Maximum depletion rate of the bucket. The peakrate does not +need to be set, it is only necessary if perfect millisecond timescale +shaping is required. + +.TP +mtu/minburst +Specifies the size of the peakrate bucket. For perfect accuracy, should be set to the MTU of the interface. +If a peakrate is needed, but some burstiness is acceptable, this size can be raised. A 3000 byte minburst +allows around 3mbit/s of peakrate, given 1000 byte packets. + +Like the regular burstsize you can also specify a +.B cell +size. +.SH EXAMPLE & USAGE + +To attach a TBF with a sustained maximum rate of 0.5mbit/s, a peakrate of 1.0mbit/s, +a 5kilobyte buffer, with a pre-bucket queue size limit calculated so the TBF causes +at most 70ms of latency, with perfect peakrate behaviour, issue: +.P +# tc qdisc add dev eth0 handle 10: root tbf rate 0.5mbit \\ + burst 5kb latency 70ms peakrate 1mbit \\ + minburst 1540 +.P +To attach an inner qdisc, for example sfq, issue: +.P +# tc qdisc add dev eth0 parent 10:1 handle 100: sfq +.P +Without inner qdisc TBF queue acts as bfifo. If the inner qdisc is changed +the limit/latency is not effective anymore. +.P + +.SH SEE ALSO +.BR tc (8) + +.SH AUTHOR +Alexey N. Kuznetsov, <kuznet@ms2.inr.ac.ru>. This manpage maintained by +bert hubert <ahu@ds9a.nl> |