Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 584 insertions, 0 deletions

diff --git a/Documentation/ABI/testing/sysfs-bus-usb b/Documentation/ABI/testing/sysfs-bus-usb
new file mode 100644
index 000000000..568103d33
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-usb
@@ -0,0 +1,584 @@
+What:		/sys/bus/usb/devices/<INTERFACE>/authorized
+Date:		August 2015
+Description:
+		This allows to authorize (1) or deauthorize (0)
+		individual interfaces instead a whole device
+		in contrast to the device authorization.
+		If a deauthorized interface will be authorized
+		so the driver probing must be triggered manually
+		by writing INTERFACE to /sys/bus/usb/drivers_probe
+		This allows to avoid side-effects with drivers
+		that need multiple interfaces.
+
+		A deauthorized interface cannot be probed or claimed.
+
+What:		/sys/bus/usb/devices/usbX/interface_authorized_default
+Date:		August 2015
+Description:
+		This is used as value that determines if interfaces
+		would be authorized by default.
+		The value can be 1 or 0. It's by default 1.
+
+What:		/sys/bus/usb/device/.../authorized
+Date:		July 2008
+KernelVersion:	2.6.26
+Contact:	David Vrabel <david.vrabel@csr.com>
+Description:
+		Authorized devices are available for use by device
+		drivers, non-authorized one are not.  By default, wired
+		USB devices are authorized.
+
+		Certified Wireless USB devices are not authorized
+		initially and should be (by writing 1) after the
+		device has been authenticated.
+
+What:		/sys/bus/usb/device/.../wusb_cdid
+Date:		July 2008
+KernelVersion:	2.6.27
+Contact:	David Vrabel <david.vrabel@csr.com>
+Description:
+		For Certified Wireless USB devices only.
+
+		A devices's CDID, as 16 space-separated hex octets.
+
+What:		/sys/bus/usb/device/.../wusb_ck
+Date:		July 2008
+KernelVersion:	2.6.27
+Contact:	David Vrabel <david.vrabel@csr.com>
+Description:
+		For Certified Wireless USB devices only.
+
+		Write the device's connection key (CK) to start the
+		authentication of the device.  The CK is 16
+		space-separated hex octets.
+
+What:		/sys/bus/usb/device/.../wusb_disconnect
+Date:		July 2008
+KernelVersion:	2.6.27
+Contact:	David Vrabel <david.vrabel@csr.com>
+Description:
+		For Certified Wireless USB devices only.
+
+		Write a 1 to force the device to disconnect
+		(equivalent to unplugging a wired USB device).
+
+What:		/sys/bus/usb/drivers/.../new_id
+Date:		October 2011
+Contact:	linux-usb@vger.kernel.org
+Description:
+		Writing a device ID to this file will attempt to
+		dynamically add a new device ID to a USB device driver.
+		This may allow the driver to support more hardware than
+		was included in the driver's static device ID support
+		table at compile time. The format for the device ID is:
+		idVendor idProduct bInterfaceClass RefIdVendor RefIdProduct
+		The vendor ID and device ID fields are required, the
+		rest is optional. The `Ref*` tuple can be used to tell the
+		driver to use the same driver_data for the new device as
+		it is used for the reference device.
+		Upon successfully adding an ID, the driver will probe
+		for the device and attempt to bind to it.  For example::
+
+		  # echo "8086 10f5" > /sys/bus/usb/drivers/foo/new_id
+
+		Here add a new device (0458:7045) using driver_data from
+		an already supported device (0458:704c)::
+
+		  # echo "0458 7045 0 0458 704c" > /sys/bus/usb/drivers/foo/new_id
+
+		Reading from this file will list all dynamically added
+		device IDs in the same format, with one entry per
+		line. For example::
+
+		  # cat /sys/bus/usb/drivers/foo/new_id
+		  8086 10f5
+		  dead beef 06
+		  f00d cafe
+
+		The list will be truncated at PAGE_SIZE bytes due to
+		sysfs restrictions.
+
+What:		/sys/bus/usb-serial/drivers/.../new_id
+Date:		October 2011
+Contact:	linux-usb@vger.kernel.org
+Description:
+		For serial USB drivers, this attribute appears under the
+		extra bus folder "usb-serial" in sysfs; apart from that
+		difference, all descriptions from the entry
+		"/sys/bus/usb/drivers/.../new_id" apply.
+
+What:		/sys/bus/usb/drivers/.../remove_id
+Date:		November 2009
+Contact:	CHENG Renquan <rqcheng@smu.edu.sg>
+Description:
+		Writing a device ID to this file will remove an ID
+		that was dynamically added via the new_id sysfs entry.
+		The format for the device ID is:
+		idVendor idProduct.	After successfully
+		removing an ID, the driver will no longer support the
+		device.  This is useful to ensure auto probing won't
+		match the driver to the device.  For example:
+		# echo "046d c315" > /sys/bus/usb/drivers/foo/remove_id
+
+		Reading from this file will list the dynamically added
+		device IDs, exactly like reading from the entry
+		"/sys/bus/usb/drivers/.../new_id"
+
+What:		/sys/bus/usb/devices/.../power/usb2_hardware_lpm
+Date:		September 2011
+Contact:	Andiry Xu <andiry.xu@amd.com>
+Description:
+		If CONFIG_PM is set and a USB 2.0 lpm-capable device is plugged
+		in to a xHCI host which support link PM, it will perform a LPM
+		test; if the test is passed and host supports USB2 hardware LPM
+		(xHCI 1.0 feature), USB2 hardware LPM will be enabled for the
+		device and the USB device directory will contain a file named
+		power/usb2_hardware_lpm.  The file holds a string value (enable
+		or disable) indicating whether or not USB2 hardware LPM is
+		enabled for the device. Developer can write y/Y/1 or n/N/0 to
+		the file to enable/disable the feature.
+
+What:		/sys/bus/usb/devices/.../power/usb3_hardware_lpm_u1
+		/sys/bus/usb/devices/.../power/usb3_hardware_lpm_u2
+Date:		November 2015
+Contact:	Kevin Strasser <kevin.strasser@linux.intel.com>
+		Lu Baolu <baolu.lu@linux.intel.com>
+Description:
+		If CONFIG_PM is set and a USB 3.0 lpm-capable device is plugged
+		in to a xHCI host which supports link PM, it will check if U1
+		and U2 exit latencies have been set in the BOS descriptor; if
+		the check is passed and the host supports USB3 hardware LPM,
+		USB3 hardware LPM will be enabled for the device and the USB
+		device directory will contain two files named
+		power/usb3_hardware_lpm_u1 and power/usb3_hardware_lpm_u2. These
+		files hold a string value (enable or disable) indicating whether
+		or not USB3 hardware LPM U1 or U2 is enabled for the device.
+
+What:		/sys/bus/usb/devices/.../ltm_capable
+Date:		July 2012
+Contact:	Sarah Sharp <sarah.a.sharp@linux.intel.com>
+Description:
+		USB 3.0 devices may optionally support Latency Tolerance
+		Messaging (LTM).  They indicate their support by setting a bit
+		in the bmAttributes field of their SuperSpeed BOS descriptors.
+		If that bit is set for the device, ltm_capable will read "yes".
+		If the device doesn't support LTM, the file will read "no".
+		The file will be present for all speeds of USB devices, and will
+		always read "no" for USB 1.1 and USB 2.0 devices.
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>
+Date:		August 2012
+Contact:	Lan Tianyu <tianyu.lan@intel.com>
+Description:
+		The /sys/bus/usb/devices/.../<hub_interface>/port<X>
+		is usb port device's sysfs directory.
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/connect_type
+Date:		January 2013
+Contact:	Lan Tianyu <tianyu.lan@intel.com>
+Description:
+		Some platforms provide usb port connect types through ACPI.
+		This attribute is to expose these information to user space.
+		The file will read "hotplug", "hardwired" and "not used" if the
+		information is available, and "unknown" otherwise.
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/location
+Date:		October 2018
+Contact:	Bjørn Mork <bjorn@mork.no>
+Description:
+		Some platforms provide usb port physical location through
+		firmware. This is used by the kernel to pair up logical ports
+		mapping to the same physical connector. The attribute exposes the
+		raw location value as a hex integer.
+
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/quirks
+Date:		May 2018
+Contact:	Nicolas Boichat <drinkcat@chromium.org>
+Description:
+		In some cases, we care about time-to-active for devices
+		connected on a specific port (e.g. non-standard USB port like
+		pogo pins), where the device to be connected is known in
+		advance, and behaves well according to the specification.
+		This attribute is a bit-field that controls the behavior of
+		a specific port:
+
+		 - Bit 0 of this field selects the "old" enumeration scheme,
+		   as it is considerably faster (it only causes one USB reset
+		   instead of 2).
+
+		   The old enumeration scheme can also be selected globally
+		   using /sys/module/usbcore/parameters/old_scheme_first, but
+		   it is often not desirable as the new scheme was introduced to
+		   increase compatibility with more devices.
+		 - Bit 1 reduces TRSTRCY to the 10 ms that are required by the
+		   USB 2.0 specification, instead of the 50 ms that are normally
+		   used to help make enumeration work better on some high speed
+		   devices.
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/over_current_count
+Date:		February 2018
+Contact:	Richard Leitner <richard.leitner@skidata.com>
+Description:
+		Most hubs are able to detect over-current situations on their
+		ports and report them to the kernel. This attribute is to expose
+		the number of over-current situation occurred on a specific port
+		to user space. This file will contain an unsigned 32 bit value
+		which wraps to 0 after its maximum is reached. This file supports
+		poll() for monitoring changes to this value in user space.
+
+		Any time this value changes the corresponding hub device will send a
+		udev event with the following attributes::
+
+		  OVER_CURRENT_PORT=/sys/bus/usb/devices/.../<hub_interface>/port<X>
+		  OVER_CURRENT_COUNT=[current value of this sysfs attribute]
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/usb3_lpm_permit
+Date:		November 2015
+Contact:	Lu Baolu <baolu.lu@linux.intel.com>
+Description:
+		Some USB3.0 devices are not friendly to USB3 LPM.  usb3_lpm_permit
+		attribute allows enabling/disabling usb3 lpm of a port. It takes
+		effect both before and after a usb device is enumerated. Supported
+		values are "0" if both u1 and u2 are NOT permitted, "u1" if only u1
+		is permitted, "u2" if only u2 is permitted, "u1_u2" if both u1 and
+		u2 are permitted.
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/connector
+Date:		December 2021
+Contact:	Heikki Krogerus <heikki.krogerus@linux.intel.com>
+Description:
+		Link to the USB Type-C connector when available. This link is
+		only created when USB Type-C Connector Class is enabled, and
+		only if the system firmware is capable of describing the
+		connection between a port and its connector.
+
+What:		/sys/bus/usb/devices/.../<hub_interface>/port<X>/disable
+Date:		June 2022
+Contact:	Michael Grzeschik <m.grzeschik@pengutronix.de>
+Description:
+		This file controls the state of a USB port, including
+		Vbus power output (but only on hubs that support
+		power switching -- most hubs don't support it). If
+		a port is disabled, the port is unusable: Devices
+		attached to the port will not be detected, initialized,
+		or enumerated.
+
+What:		/sys/bus/usb/devices/.../power/usb2_lpm_l1_timeout
+Date:		May 2013
+Contact:	Mathias Nyman <mathias.nyman@linux.intel.com>
+Description:
+		USB 2.0 devices may support hardware link power management (LPM)
+		L1 sleep state. The usb2_lpm_l1_timeout attribute allows
+		tuning the timeout for L1 inactivity timer (LPM timer), e.g.
+		needed inactivity time before host requests the device to go to L1 sleep.
+		Useful for power management tuning.
+		Supported values are 0 - 65535 microseconds.
+
+What:		/sys/bus/usb/devices/.../power/usb2_lpm_besl
+Date:		May 2013
+Contact:	Mathias Nyman <mathias.nyman@linux.intel.com>
+Description:
+		USB 2.0 devices that support hardware link power management (LPM)
+		L1 sleep state now use a best effort service latency value (BESL) to
+		indicate the best effort to resumption of service to the device after the
+		initiation of the resume event.
+		If the device does not have a preferred besl value then the host can select
+		one instead. This usb2_lpm_besl attribute allows to tune the host selected besl
+		value in order to tune power saving and service latency.
+
+		Supported values are 0 - 15.
+		More information on how besl values map to microseconds can be found in
+		USB 2.0 ECN Errata for Link Power Management, section 4.10)
+
+What:		/sys/bus/usb/devices/.../rx_lanes
+Date:		March 2018
+Contact:	Mathias Nyman <mathias.nyman@linux.intel.com>
+Description:
+		Number of rx lanes the device is using.
+		USB 3.2 adds Dual-lane support, 2 rx and 2 tx lanes over Type-C.
+		Inter-Chip SSIC devices support asymmetric lanes up to 4 lanes per
+		direction. Devices before USB 3.2 are single lane (rx_lanes = 1)
+
+What:		/sys/bus/usb/devices/.../tx_lanes
+Date:		March 2018
+Contact:	Mathias Nyman <mathias.nyman@linux.intel.com>
+Description:
+		Number of tx lanes the device is using.
+		USB 3.2 adds Dual-lane support, 2 rx and 2 tx -lanes over Type-C.
+		Inter-Chip SSIC devices support asymmetric lanes up to 4 lanes per
+		direction. Devices before USB 3.2 are single lane (tx_lanes = 1)
+
+What:		/sys/bus/usb/devices/usbX/bAlternateSetting
+Description:
+		The current interface alternate setting number, in decimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bcdDevice
+Description:
+		The device's release number, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bConfigurationValue
+Description:
+		While a USB device typically have just one configuration
+		setting, some devices support multiple configurations.
+
+		This value shows the current configuration, in decimal.
+
+		Changing its value will change the device's configuration
+		to another setting.
+
+		The number of configurations supported by a device is at:
+
+			/sys/bus/usb/devices/usbX/bNumConfigurations
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bDeviceClass
+Description:
+		Class code of the device, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bDeviceProtocol
+Description:
+		Protocol code of the device, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bDeviceSubClass
+Description:
+		Subclass code of the device, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bInterfaceClass
+Description:
+		Class code of the interface, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bInterfaceNumber
+Description:
+		Interface number, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bInterfaceProtocol
+Description:
+		Protocol code of the interface, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bInterfaceSubClass
+Description:
+		Subclass code of the interface, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bmAttributes
+Description:
+		Attributes of the current configuration, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bMaxPacketSize0
+Description:
+		Maximum endpoint 0 packet size, in decimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bMaxPower
+Description:
+		Maximum power consumption of the active configuration of
+		the device, in miliamperes.
+
+What:		/sys/bus/usb/devices/usbX/bNumConfigurations
+Description:
+		Number of the possible configurations of the device, in
+		decimal. The current configuration is controlled via:
+
+			/sys/bus/usb/devices/usbX/bConfigurationValue
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bNumEndpoints
+Description:
+		Number of endpoints used on this interface, in hexadecimal.
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/bNumInterfaces
+Description:
+		Number of interfaces on this device, in decimal.
+
+What:		/sys/bus/usb/devices/usbX/busnum
+Description:
+		Number of the bus.
+
+What:		/sys/bus/usb/devices/usbX/configuration
+Description:
+		Contents of the string descriptor associated with the
+		current configuration. It may include the firmware version
+		of a device and/or its serial number.
+
+What:		/sys/bus/usb/devices/usbX/descriptors
+Description:
+		Contains the interface descriptors, in binary.
+
+What:		/sys/bus/usb/devices/usbX/idProduct
+Description:
+		Product ID, in hexadecimal.
+
+What:		/sys/bus/usb/devices/usbX/idVendor
+Description:
+		Vendor ID, in hexadecimal.
+
+What:		/sys/bus/usb/devices/usbX/devspec
+Description:
+		Displays the Device Tree Open Firmware node of the interface.
+
+What:		/sys/bus/usb/devices/usbX/avoid_reset_quirk
+Description:
+		Most devices have this set to zero.
+
+		If the value is 1, enable a USB quirk that prevents this
+		device to use reset.
+
+		(read/write)
+
+What:		/sys/bus/usb/devices/usbX/devnum
+Description:
+		USB interface device number, in decimal.
+
+What:		/sys/bus/usb/devices/usbX/devpath
+Description:
+		String containing the USB interface device path.
+
+What:		/sys/bus/usb/devices/usbX/manufacturer
+Description:
+		Vendor specific string containing the name of the
+		manufacturer of the device.
+
+What:		/sys/bus/usb/devices/usbX/maxchild
+Description:
+		Number of ports of an USB hub
+
+What:		/sys/bus/usb/devices/usbX/persist
+Description:
+		Keeps the device even if it gets disconnected.
+
+What:		/sys/bus/usb/devices/usbX/product
+Description:
+		Vendor specific string containing the name of the
+		device's product.
+
+What:		/sys/bus/usb/devices/usbX/speed
+Description:
+		Shows the device's max speed, according to the USB version,
+		in Mbps.
+		Can be:
+
+			=======		====================
+			Unknown		speed unknown
+			1.5		Low speed
+			15		Full speed
+			480		High Speed
+			5000		Super Speed
+			10000		Super Speed+
+			20000		Super Speed+ Gen 2x2
+			=======		====================
+
+What:		/sys/bus/usb/devices/usbX/supports_autosuspend
+Description:
+		Returns 1 if the device doesn't support autosuspend.
+		Otherwise, returns 0.
+
+What:		/sys/bus/usb/devices/usbX/urbnum
+Description:
+		Number of URBs submitted for the whole device.
+
+What:		/sys/bus/usb/devices/usbX/version
+Description:
+		String containing the USB device version, as encoded
+		at the BCD descriptor.
+
+What:		/sys/bus/usb/devices/usbX/power/autosuspend
+Description:
+		Time in milliseconds for the device to autosuspend. If the
+		value is negative, then autosuspend is prevented.
+
+		(read/write)
+
+What:		/sys/bus/usb/devices/usbX/power/active_duration
+Description:
+		The total time the device has not been suspended.
+
+What:		/sys/bus/usb/devices/usbX/power/connected_duration
+Description:
+		The total time (in msec) that the device has been connected.
+
+What:		/sys/bus/usb/devices/usbX/power/level
+Description:
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/bEndpointAddress
+Description:
+		The address of the endpoint described by this descriptor,
+		in hexadecimal. The endpoint direction on this bitmapped field
+		is also shown at:
+
+			/sys/bus/usb/devices/usbX/ep_<N>/direction
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/bInterval
+Description:
+		The interval of the endpoint as described on its descriptor,
+		in hexadecimal. The actual interval depends on the version
+		of the USB. Also shown in time units at
+		/sys/bus/usb/devices/usbX/ep_<N>/interval.
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/bLength
+Description:
+		Number of bytes of the endpoint descriptor, in hexadecimal.
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/bmAttributes
+Description:
+		Attributes which apply to the endpoint as described on its
+		descriptor, in hexadecimal. The endpoint type on this
+		bitmapped field is also shown at:
+
+			/sys/bus/usb/devices/usbX/ep_<N>/type
+
+		See USB specs for its meaning.
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/direction
+Description:
+		Direction of the endpoint. Can be:
+
+		    - both (on control endpoints)
+		    - in
+		    - out
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/interval
+Description:
+		Interval for polling endpoint for data transfers, in
+		milisseconds or microseconds.
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/type
+Description:
+		Descriptor type. Can be:
+
+		    - Control
+		    - Isoc
+		    - Bulk
+		    - Interrupt
+		    - unknown
+
+What:		/sys/bus/usb/devices/usbX/ep_<N>/wMaxPacketSize
+Description:
+		Maximum packet size this endpoint is capable of
+		sending or receiving, in hexadecimal.