Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 190 insertions, 0 deletions

diff --git a/Documentation/ABI/testing/sysfs-driver-w1_therm b/Documentation/ABI/testing/sysfs-driver-w1_therm
new file mode 100644
index 000000000..74642c73d
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-w1_therm
@@ -0,0 +1,190 @@
+What:		/sys/bus/w1/devices/.../alarms
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) read or write TH and TL (Temperature High an Low) alarms.
+		Values shall be space separated and in the device range
+		(typical -55 degC to 125 degC), if not values will be trimmed
+		to device min/max capabilities. Values are integer as they are
+		stored in a 8bit register in the device. Lowest value is
+		automatically put to TL. Once set, alarms could be search at
+		master level, refer to Documentation/w1/w1-generic.rst for
+		detailed information
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../eeprom_cmd
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(WO) writing that file will either trigger a save of the
+		device data to its embedded EEPROM, either restore data
+		embedded in device EEPROM. Be aware that devices support
+		limited EEPROM writing cycles (typical 50k)
+
+			* 'save': save device RAM to EEPROM
+			* 'restore': restore EEPROM data in device RAM
+
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../ext_power
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RO) return the power status by asking the device
+
+			* '0': device parasite powered
+			* '1': device externally powered
+			* '-xx': xx is kernel error when reading power status
+
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../resolution
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) get or set the device resolution (on supported devices,
+		if not, this entry is not present). Note that the resolution
+		will be changed only in device RAM, so it will be cleared when
+		power is lost. Trigger a 'save' to EEPROM command to keep
+		values after power-on. Read or write are :
+
+			* '9..14': device resolution in bit
+			  or resolution to set in bit
+			* '-xx': xx is kernel error when reading the resolution
+			* Anything else: do nothing
+
+		Some DS18B20 clones are fixed in 12-bit resolution, so the
+		actual resolution is read back from the chip and verified. Error
+		is reported if the results differ.
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../temperature
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RO) return the temperature in 1/1000 degC.
+
+			* If a bulk read has been triggered, it will directly
+			  return the temperature computed when the bulk read
+			  occurred, if available. If not yet available, nothing
+			  is returned (a debug kernel message is sent), you
+			  should retry later on.
+			* If no bulk read has been triggered, it will trigger
+			  a conversion and send the result. Note that the
+			  conversion duration depend on the resolution (if
+			  device support this feature). It takes 94ms in 9bits
+			  resolution, 750ms for 12bits.
+
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../w1_slave
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) return the temperature in 1/1000 degC.
+		*read*: return 2 lines with the hexa output data sent on the
+		bus, return the CRC check and temperature in 1/1000 degC
+		*write*:
+
+			* '0' : save the 2 or 3 bytes to the device EEPROM
+			  (i.e. TH, TL and config register)
+			* '9..14' : set the device resolution in RAM
+			  (if supported)
+			* Anything else: do nothing
+
+		refer to Documentation/w1/slaves/w1_therm.rst for detailed
+		information.
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/w1_bus_masterXX/therm_bulk_read
+Date:		May 2020
+Contact:	Akira Shimahara <akira215corp@gmail.com>
+Description:
+		(RW) trigger a bulk read conversion. read the status
+
+		*read*:
+			* '-1':
+				conversion in progress on at least 1 sensor
+			* '1' :
+				conversion complete but at least one sensor
+				value has not been read yet
+			* '0' :
+				no bulk operation. Reading temperature will
+				trigger a conversion on each device
+
+		*write*:
+			'trigger': trigger a bulk read on all supporting
+			devices on the bus
+
+		Note that if a bulk read is sent but one sensor is not read
+		immediately, the next access to temperature on this device
+		will return the temperature measured at the time of issue
+		of the bulk read command (not the current temperature).
+Users:		any user space application which wants to communicate with
+		w1_term device
+
+
+What:		/sys/bus/w1/devices/.../conv_time
+Date:		July 2020
+Contact:	Ivan Zaentsev <ivan.zaentsev@wirenboard.ru>
+Description:
+		(RW) Get, set, or measure a temperature conversion time. The
+		setting remains active until a resolution change. Then it is
+		reset to default (datasheet) conversion time for a new
+		resolution.
+
+		*read*:
+			Actual conversion time in milliseconds.
+
+		*write*:
+			* '0':
+			     Set the default conversion time from the datasheet.
+			* '1':
+			     Measure and set the conversion time. Make a single
+			     temperature conversion, measure an actual value.
+			     Increase it by 20% for temperature range. A new
+			     conversion time can be obtained by reading this
+			     same attribute.
+			* other positive value:
+			     Set the conversion time in milliseconds.
+
+Users:		An application using the w1_term device
+
+
+What:		/sys/bus/w1/devices/.../features
+Date:		July 2020
+Contact:	Ivan Zaentsev <ivan.zaentsev@wirenboard.ru>
+Description:
+		(RW) Control optional driver settings.
+		Bit masks to read/write (bitwise OR):
+
+		== ============================================================
+                 1 Enable check for conversion success. If byte 6 of
+                   scratchpad memory is 0xC after conversion, and
+                   temperature reads 85.00 (powerup value) or 127.94
+                   (insufficient power) - return a conversion error.
+
+                2  Enable poll for conversion completion. Generate read cycles
+                   after the conversion start and wait for 1's. In parasite
+                   power mode this feature is not available.
+		== ============================================================
+
+		*read*:
+		    Currently selected features.
+
+		*write*:
+		    Select features.
+
+Users:		An application using the w1_term device