Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 187 insertions, 0 deletions

diff --git a/Documentation/driver-api/men-chameleon-bus.rst b/Documentation/driver-api/men-chameleon-bus.rst
new file mode 100644
index 000000000..6f0b9ee47
--- /dev/null
+++ b/Documentation/driver-api/men-chameleon-bus.rst
@@ -0,0 +1,187 @@
+=================
+MEN Chameleon Bus
+=================
+
+.. Table of Contents
+   =================
+   1 Introduction
+       1.1 Scope of this Document
+       1.2 Limitations of the current implementation
+   2 Architecture
+       2.1 MEN Chameleon Bus
+       2.2 Carrier Devices
+       2.3 Parser
+   3 Resource handling
+       3.1 Memory Resources
+       3.2 IRQs
+   4 Writing an MCB driver
+       4.1 The driver structure
+       4.2 Probing and attaching
+       4.3 Initializing the driver
+       4.4 Using DMA
+
+
+Introduction
+============
+
+This document describes the architecture and implementation of the MEN
+Chameleon Bus (called MCB throughout this document).
+
+Scope of this Document
+----------------------
+
+This document is intended to be a short overview of the current
+implementation and does by no means describe the complete possibilities of MCB
+based devices.
+
+Limitations of the current implementation
+-----------------------------------------
+
+The current implementation is limited to PCI and PCIe based carrier devices
+that only use a single memory resource and share the PCI legacy IRQ.  Not
+implemented are:
+
+- Multi-resource MCB devices like the VME Controller or M-Module carrier.
+- MCB devices that need another MCB device, like SRAM for a DMA Controller's
+  buffer descriptors or a video controller's video memory.
+- A per-carrier IRQ domain for carrier devices that have one (or more) IRQs
+  per MCB device like PCIe based carriers with MSI or MSI-X support.
+
+Architecture
+============
+
+MCB is divided into 3 functional blocks:
+
+- The MEN Chameleon Bus itself,
+- drivers for MCB Carrier Devices and
+- the parser for the Chameleon table.
+
+MEN Chameleon Bus
+-----------------
+
+The MEN Chameleon Bus is an artificial bus system that attaches to a so
+called Chameleon FPGA device found on some hardware produced my MEN Mikro
+Elektronik GmbH. These devices are multi-function devices implemented in a
+single FPGA and usually attached via some sort of PCI or PCIe link. Each
+FPGA contains a header section describing the content of the FPGA. The
+header lists the device id, PCI BAR, offset from the beginning of the PCI
+BAR, size in the FPGA, interrupt number and some other properties currently
+not handled by the MCB implementation.
+
+Carrier Devices
+---------------
+
+A carrier device is just an abstraction for the real world physical bus the
+Chameleon FPGA is attached to. Some IP Core drivers may need to interact with
+properties of the carrier device (like querying the IRQ number of a PCI
+device). To provide abstraction from the real hardware bus, an MCB carrier
+device provides callback methods to translate the driver's MCB function calls
+to hardware related function calls. For example a carrier device may
+implement the get_irq() method which can be translated into a hardware bus
+query for the IRQ number the device should use.
+
+Parser
+------
+
+The parser reads the first 512 bytes of a Chameleon device and parses the
+Chameleon table. Currently the parser only supports the Chameleon v2 variant
+of the Chameleon table but can easily be adopted to support an older or
+possible future variant. While parsing the table's entries new MCB devices
+are allocated and their resources are assigned according to the resource
+assignment in the Chameleon table. After resource assignment is finished, the
+MCB devices are registered at the MCB and thus at the driver core of the
+Linux kernel.
+
+Resource handling
+=================
+
+The current implementation assigns exactly one memory and one IRQ resource
+per MCB device. But this is likely going to change in the future.
+
+Memory Resources
+----------------
+
+Each MCB device has exactly one memory resource, which can be requested from
+the MCB bus. This memory resource is the physical address of the MCB device
+inside the carrier and is intended to be passed to ioremap() and friends. It
+is already requested from the kernel by calling request_mem_region().
+
+IRQs
+----
+
+Each MCB device has exactly one IRQ resource, which can be requested from the
+MCB bus. If a carrier device driver implements the ->get_irq() callback
+method, the IRQ number assigned by the carrier device will be returned,
+otherwise the IRQ number inside the Chameleon table will be returned. This
+number is suitable to be passed to request_irq().
+
+Writing an MCB driver
+=====================
+
+The driver structure
+--------------------
+
+Each MCB driver has a structure to identify the device driver as well as
+device ids which identify the IP Core inside the FPGA. The driver structure
+also contains callback methods which get executed on driver probe and
+removal from the system::
+
+	static const struct mcb_device_id foo_ids[] = {
+		{ .device = 0x123 },
+		{ }
+	};
+	MODULE_DEVICE_TABLE(mcb, foo_ids);
+
+	static struct mcb_driver foo_driver = {
+	driver = {
+		.name = "foo-bar",
+		.owner = THIS_MODULE,
+	},
+		.probe = foo_probe,
+		.remove = foo_remove,
+		.id_table = foo_ids,
+	};
+
+Probing and attaching
+---------------------
+
+When a driver is loaded and the MCB devices it services are found, the MCB
+core will call the driver's probe callback method. When the driver is removed
+from the system, the MCB core will call the driver's remove callback method::
+
+	static init foo_probe(struct mcb_device *mdev, const struct mcb_device_id *id);
+	static void foo_remove(struct mcb_device *mdev);
+
+Initializing the driver
+-----------------------
+
+When the kernel is booted or your foo driver module is inserted, you have to
+perform driver initialization. Usually it is enough to register your driver
+module at the MCB core::
+
+	static int __init foo_init(void)
+	{
+		return mcb_register_driver(&foo_driver);
+	}
+	module_init(foo_init);
+
+	static void __exit foo_exit(void)
+	{
+		mcb_unregister_driver(&foo_driver);
+	}
+	module_exit(foo_exit);
+
+The module_mcb_driver() macro can be used to reduce the above code::
+
+	module_mcb_driver(foo_driver);
+
+Using DMA
+---------
+
+To make use of the kernel's DMA-API's function, you will need to use the
+carrier device's 'struct device'. Fortunately 'struct mcb_device' embeds a
+pointer (->dma_dev) to the carrier's device for DMA purposes::
+
+        ret = dma_set_mask_and_coherent(&mdev->dma_dev, DMA_BIT_MASK(dma_bits));
+        if (rc)
+                /* Handle errors */