Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 127 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/am335x-bonegreen-wireless.dts b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
new file mode 100644
index 000000000..d388cffa1
--- /dev/null
+++ b/arch/arm/boot/dts/am335x-bonegreen-wireless.dts
@@ -0,0 +1,127 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
+ */
+/dts-v1/;
+
+#include "am33xx.dtsi"
+#include "am335x-bone-common.dtsi"
+#include "am335x-bonegreen-common.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "TI AM335x BeagleBone Green Wireless";
+	compatible = "ti,am335x-bone-green-wireless", "ti,am335x-bone-green", "ti,am335x-bone-black", "ti,am335x-bone", "ti,am33xx";
+
+	wlan_en_reg: fixedregulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "wlan-en-regulator";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		startup-delay-us = <70000>;
+
+		/* WL_EN */
+		gpio = <&gpio0 26 0>;
+		enable-active-high;
+	};
+};
+
+&am33xx_pinmux {
+	bt_pins: pinmux_bt_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_BEN1, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_ad12.gpio1_28 BT_EN */
+		>;
+	};
+
+	mmc3_pins: pinmux_mmc3_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD12, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_ad12.mmc2_dat0 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD13, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_ad13.mmc2_dat1 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD14, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_ad14.mmc2_dat2 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD15, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_ad15.mmc2_dat3 */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN3, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_csn3.mmc2_cmd */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CLK, PIN_INPUT_PULLUP, MUX_MODE3)	/* gpmc_clk.mmc2_clk */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD3, PIN_INPUT_PULLUP, MUX_MODE1)	/* gmii1_rxd3.uart3_rxd */
+			AM33XX_PADCONF(AM335X_PIN_MII1_RXD2, PIN_OUTPUT_PULLDOWN, MUX_MODE1)	/* gmii1_rxd2.uart3_txd */
+			AM33XX_PADCONF(AM335X_PIN_MDIO, PIN_INPUT, MUX_MODE3)		/* mdio_data.uart3_ctsn */
+			AM33XX_PADCONF(AM335X_PIN_MDC, PIN_OUTPUT_PULLDOWN, MUX_MODE3)	/* mdio_clk.uart3_rtsn */
+		>;
+	};
+
+	wl18xx_pins: pinmux_wl18xx_pins {
+		pinctrl-single,pins = <
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD10, PIN_OUTPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad10.gpio0_26 WL_EN */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_AD11, PIN_INPUT_PULLDOWN, MUX_MODE7)	/* gpmc_ad11.gpio0_27 WL_IRQ */
+			AM33XX_PADCONF(AM335X_PIN_GPMC_CSN0, PIN_OUTPUT_PULLUP, MUX_MODE7)	/* gpmc_csn0.gpio1_29 LS_BUF_EN */
+		>;
+	};
+};
+
+&mac_sw {
+	status = "disabled";
+};
+
+&mmc3 {
+	dmas = <&edma_xbar 12 0 1
+		&edma_xbar 13 0 2>;
+	dma-names = "tx", "rx";
+	status = "okay";
+	vmmc-supply = <&wlan_en_reg>;
+	bus-width = <4>;
+	non-removable;
+	cap-power-off-card;
+	keep-power-in-suspend;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc3_pins &wl18xx_pins>;
+
+	#address-cells = <1>;
+	#size-cells = <0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins &bt_pins>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "ti,wl1835-st";
+		enable-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&gpio1 {
+	ls-buf-en-hog {
+		gpio-hog;
+		gpios = <29 GPIO_ACTIVE_HIGH>;
+		output-high;
+		line-name = "LS_BUF_EN";
+	};
+};
+
+/* BT_AUD_OUT from wl1835 has to be pulled low when WL_EN is activated.*/
+/* in case it isn't, wilink8 ends up in one of the test modes that     */
+/* intruces various issues (elp wkaeup timeouts etc.)                  */
+/* On the BBGW this pin is routed through the level shifter (U21) that */
+/* introduces a pullup on the line and wilink8 ends up in a bad state. */
+/* use a gpio hog to force this pin low. An alternative may be adding  */
+/* an external pulldown on U21 pin 4.                                  */
+
+&gpio3 {
+	bt-aud-in-hog {
+		gpio-hog;
+		gpios = <16 GPIO_ACTIVE_HIGH>;
+		output-low;
+		line-name = "MCASP0_AHCLKR";
+	};
+};