Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1011 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
new file mode 100644
index 000000000..573e4dc66
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -0,0 +1,1011 @@
+// SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include "qcom-msm8660.dtsi"
+
+/ {
+	model = "Qualcomm APQ8060 Dragonboard";
+	compatible = "qcom,apq8060-dragonboard", "qcom,msm8660";
+
+	aliases {
+		serial0 = &gsbi12_serial;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		/* Main power of the board: 3.7V */
+		vph: regulator-fixed {
+			compatible = "regulator-fixed";
+			regulator-min-microvolt = <3700000>;
+			regulator-max-microvolt = <3700000>;
+			regulator-name = "VPH";
+			regulator-type = "voltage";
+			regulator-always-on;
+			regulator-boot-on;
+		};
+
+		/* GPIO controlled ethernet power regulator */
+		dragon_veth: xc622a331mrg {
+			compatible = "regulator-fixed";
+			regulator-name = "XC6222A331MR-G";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			vin-supply = <&vph>;
+			gpio = <&pm8058_gpio 40 GPIO_ACTIVE_HIGH>;
+			enable-active-high;
+			pinctrl-names = "default";
+			pinctrl-0 = <&dragon_veth_gpios>;
+			regulator-always-on;
+		};
+
+		/* VDDvario fixed regulator */
+		dragon_vario: nds332p {
+			compatible = "regulator-fixed";
+			regulator-name = "NDS332P";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			vin-supply = <&pm8058_s3>;
+		};
+
+		/* This is a levelshifter for SDCC5 */
+		dragon_vio_txb: txb0104rgyr {
+			compatible = "regulator-fixed";
+			regulator-name = "Dragon SDCC levelshifter";
+			vin-supply = <&pm8058_l14>;
+			regulator-always-on;
+		};
+	};
+
+	/*
+	 * Capella CM3605 light and proximity sensor mounted directly
+	 * on the sensor board.
+	 */
+	cm3605 {
+		compatible = "capella,cm3605";
+		vdd-supply = <&pm8058_l14>; // 2.85V
+		aset-gpios = <&pm8058_gpio 35 GPIO_ACTIVE_LOW>;
+		capella,aset-resistance-ohms = <100000>;
+		/* Trig on both edges - getting close or far away */
+		interrupts-extended = <&pm8058_gpio 34 IRQ_TYPE_EDGE_BOTH>;
+		/* MPP05 analog input to the XOADC */
+		io-channels = <&xoadc 0x00 0x05>;
+		io-channel-names = "aout";
+		pinctrl-names = "default";
+		pinctrl-0 = <&dragon_cm3605_gpios>, <&dragon_cm3605_mpps>;
+	};
+
+	soc {
+		pinctrl@800000 {
+			/* eMMC pins, all 8 data lines connected */
+			dragon_sdcc1_pins: sdcc1 {
+				mux {
+					pins = "gpio159", "gpio160", "gpio161",
+					     "gpio162", "gpio163", "gpio164",
+					     "gpio165", "gpio166", "gpio167",
+					     "gpio168";
+					     function = "sdc1";
+				};
+				clk {
+					pins = "gpio167"; /* SDC1 CLK */
+					drive-strength = <16>;
+					bias-disable;
+				};
+				cmd {
+					pins = "gpio168"; /* SDC1 CMD */
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+				data {
+					/* SDC1 D0 to D7 */
+					pins = "gpio159", "gpio160", "gpio161", "gpio162",
+					     "gpio163", "gpio164", "gpio165", "gpio166";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			/*
+			 * The SDCC3 pins are hardcoded (non-muxable) but need some pin
+			 * configuration.
+			 */
+			dragon_sdcc3_pins: sdcc3 {
+				clk {
+					pins = "sdc3_clk";
+					drive-strength = <8>;
+					bias-disable;
+				};
+				cmd {
+					pins = "sdc3_cmd";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+				data {
+					pins = "sdc3_data";
+					drive-strength = <8>;
+					bias-pull-up;
+				};
+			};
+
+			/* Second SD card slot pins */
+			dragon_sdcc5_pins: sdcc5 {
+				mux {
+					pins = "gpio95", "gpio96", "gpio97",
+					    "gpio98", "gpio99", "gpio100";
+					function = "sdc5";
+				};
+				clk {
+					pins = "gpio97"; /* SDC5 CLK */
+					drive-strength = <16>;
+					bias-disable;
+				};
+				cmd {
+					pins = "gpio95"; /* SDC5 CMD */
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+				data {
+					/* SDC5 D0 to D3 */
+					pins = "gpio96", "gpio98", "gpio99", "gpio100";
+					drive-strength = <10>;
+					bias-pull-up;
+				};
+			};
+
+			dragon_gsbi3_i2c_pins: gsbi3_i2c {
+				mux {
+					pins = "gpio43", "gpio44";
+					function = "gsbi3";
+				};
+				pinconf {
+					pins = "gpio43", "gpio44";
+					drive-strength = <8>;
+					/* These have external pull-up 2.2kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
+			dragon_gsbi8_i2c_pins: gsbi8_i2c {
+				mux {
+					pins = "gpio64", "gpio65";
+					function = "gsbi8";
+				};
+				pinconf {
+					pins = "gpio64", "gpio65";
+					drive-strength = <16>;
+					/* These have external pull-up 2.2kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
+			dragon_gsbi12_i2c_pins: gsbi12_i2c {
+				mux {
+					pins = "gpio115", "gpio116";
+					function = "gsbi12";
+				};
+				pinconf {
+					pins = "gpio115", "gpio116";
+					drive-strength = <16>;
+					/* These have external pull-up 4.7kOhm to 1.8V */
+					bias-disable;
+				};
+			};
+
+			/* Primary serial port uart 0 pins */
+			dragon_gsbi12_serial_pins: gsbi12_serial {
+				mux {
+					pins = "gpio117", "gpio118";
+					function = "gsbi12";
+				};
+				tx {
+					pins = "gpio117";
+					drive-strength = <8>;
+					bias-disable;
+				};
+				rx {
+					pins = "gpio118";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+
+			dragon_ebi2_pins: ebi2 {
+				/*
+				 * Pins used by EBI2 on the Dragonboard, actually only
+				 * CS2 is used by a real peripheral. CS0 is just
+				 * routed to a test point.
+				 */
+				mux0 {
+					pins =
+					    /* "gpio39", CS1A_N this is not good to mux */
+					    "gpio40", /* CS2A_N */
+					    "gpio134"; /* CS0_N testpoint TP29 */
+					function = "ebi2cs";
+				};
+				mux1 {
+					pins =
+					    /* EBI2_ADDR_7 downto EBI2_ADDR_0 address bus */
+					    "gpio123", "gpio124", "gpio125", "gpio126",
+					    "gpio127", "gpio128", "gpio129", "gpio130",
+					    /* EBI2_DATA_15 downto EBI2_DATA_0 data bus */
+					    "gpio135", "gpio136", "gpio137", "gpio138",
+					    "gpio139", "gpio140", "gpio141", "gpio142",
+					    "gpio143", "gpio144", "gpio145", "gpio146",
+					    "gpio147", "gpio148", "gpio149", "gpio150",
+					    "gpio151", /* EBI2_OE_N */
+					    "gpio153", /* EBI2_ADV */
+					    "gpio157"; /* EBI2_WE_N */
+					function = "ebi2";
+				};
+			};
+
+			/* Interrupt line for the KXSD9 accelerometer */
+			dragon_kxsd9_gpios: kxsd9 {
+				irq {
+					pins = "gpio57"; /* IRQ line */
+					bias-pull-up;
+				};
+			};
+
+			dragon_tma340_gpios: tma340 {
+				reset {
+					/* RESET line, TS_ATTN, WAKE_CTP */
+					pins = "gpio58";
+					function = "gpio";
+					drive-strength = <6>;
+					bias-disable;
+				};
+				irq {
+					pins = "gpio61"; /* IRQ line */
+					function = "gpio";
+					drive-strength = <2>;
+					bias-pull-up;
+				};
+			};
+		};
+
+		qcom,ssbi@500000 {
+			pmic@0 {
+				keypad@148 {
+					linux,keymap = <
+					MATRIX_KEY(0, 0, KEY_MENU)
+					MATRIX_KEY(0, 2, KEY_1)
+					MATRIX_KEY(0, 3, KEY_4)
+					MATRIX_KEY(0, 4, KEY_7)
+					MATRIX_KEY(1, 0, KEY_UP)
+					MATRIX_KEY(1, 1, KEY_LEFT)
+					MATRIX_KEY(1, 2, KEY_DOWN)
+					MATRIX_KEY(1, 3, KEY_5)
+					MATRIX_KEY(1, 3, KEY_8)
+					MATRIX_KEY(2, 0, KEY_HOME)
+					MATRIX_KEY(2, 1, KEY_REPLY)
+					MATRIX_KEY(2, 2, KEY_2)
+					MATRIX_KEY(2, 3, KEY_6)
+					MATRIX_KEY(3, 0, KEY_VOLUMEUP)
+					MATRIX_KEY(3, 1, KEY_RIGHT)
+					MATRIX_KEY(3, 2, KEY_3)
+					MATRIX_KEY(3, 3, KEY_9)
+					MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE)
+					MATRIX_KEY(4, 0, KEY_VOLUMEDOWN)
+					MATRIX_KEY(4, 1, KEY_BACK)
+					MATRIX_KEY(4, 2, KEY_CAMERA)
+					MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE)
+					>;
+					keypad,num-rows = <6>;
+					keypad,num-columns = <5>;
+				};
+
+				gpio@150 {
+					dragon_ethernet_gpios: ethernet-state {
+						pinconf {
+							pins = "gpio7";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_bmp085_gpios: bmp085-state {
+						pinconf {
+							pins = "gpio16";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_mpu3050_gpios: mpu3050-state {
+						pinconf {
+							pins = "gpio17";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_sdcc3_gpios: sdcc3-state {
+						pinconf {
+							pins = "gpio22";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_sdcc5_gpios: sdcc5-state {
+						pinconf {
+							pins = "gpio26";
+							function = "normal";
+							input-enable;
+							bias-pull-up;
+							qcom,pull-up-strength = <PMIC_GPIO_PULL_UP_30>;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_ak8975_gpios: ak8975-state {
+						pinconf {
+							pins = "gpio33";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_cm3605_gpios: cm3605-state {
+						/* Pin 34 connected to the proxy IRQ */
+						gpio34-pins {
+							pins = "gpio34";
+							function = "normal";
+							input-enable;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+						/* Pin 35 connected to ASET */
+						gpio35-pins {
+							pins = "gpio35";
+							function = "normal";
+							output-high;
+							bias-disable;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+					dragon_veth_gpios: veth-state {
+						pinconf {
+							pins = "gpio40";
+							function = "normal";
+							bias-disable;
+							drive-push-pull;
+						};
+					};
+				};
+
+				mpps@50 {
+					dragon_cm3605_mpps: cm3605-mpps-state {
+						mpp5 {
+							pins = "mpp5";
+							function = "analog";
+							input-enable;
+							bias-high-impedance;
+							/* Let's use channel 5 */
+							qcom,amux-route = <PMIC_MPP_AMUX_ROUTE_CH5>;
+							power-source = <PM8058_GPIO_S3>;
+						};
+					};
+				};
+
+				xoadc@197 {
+					/* Reference voltage 2.2 V */
+					xoadc-ref-supply = <&pm8058_l18>;
+
+					/* Board-specific channels */
+					mpp5@5 {
+						/* Connected to AOUT of ALS sensor */
+						reg = <0x00 0x05>;
+					};
+					mpp6@6 {
+						/* Connected to test point TP43 */
+						reg = <0x00 0x06>;
+					};
+					mpp7@7 {
+						/* Connected to battery thermistor */
+						reg = <0x00 0x07>;
+					};
+					mpp8@8 {
+						/* Connected to battery ID detector */
+						reg = <0x00 0x08>;
+					};
+					mpp9@9 {
+						/* Connected to XO thermistor */
+						reg = <0x00 0x09>;
+					};
+				};
+
+				led@48 {
+					/*
+					 * The keypad LED @0x48 is routed to
+					 * the sensor board where it is
+					 * connected to an infrared LED
+					 * SFH4650 (60mW, @850nm) next to the
+					 * ambient light and proximity sensor
+					 * Capella Microsystems CM3605.
+					 */
+					compatible = "qcom,pm8058-keypad-led";
+					reg = <0x48>;
+					label = "pm8058:infrared:proximitysensor";
+					default-state = "off";
+					linux,default-trigger = "cm3605";
+				};
+				led@131 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x131>;
+					label = "pm8058:red";
+					color = <LED_COLOR_ID_RED>;
+					default-state = "off";
+				};
+				led@132 {
+					/*
+					 * This is actually green too on my
+					 * board, but documented as yellow.
+					 */
+					compatible = "qcom,pm8058-led";
+					reg = <0x132>;
+					label = "pm8058:yellow";
+					color = <LED_COLOR_ID_YELLOW>;
+					default-state = "off";
+					linux,default-trigger = "mmc0";
+				};
+				led@133 {
+					compatible = "qcom,pm8058-led";
+					reg = <0x133>;
+					label = "pm8058:green";
+					function = LED_FUNCTION_HEARTBEAT;
+					color = <LED_COLOR_ID_GREEN>;
+					default-state = "on";
+					linux,default-trigger = "heartbeat";
+				};
+			};
+		};
+
+		gsbi@16200000 {
+			qcom,mode = <GSBI_PROT_I2C>;
+			status = "okay";
+
+			gsbi3_i2c: i2c@16280000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi3_i2c_pins>;
+				status = "okay";
+
+				touchscreen@24 {
+					compatible = "cypress,cy8ctma340";
+					reg = <0x24>;
+					/* Certainly we can do at least 400 kHz */
+					clock-frequency = <400000>;
+					/* IRQ on GPIO61 called /CTP_INT */
+					interrupt-parent = <&tlmm>;
+					interrupts = <61 IRQ_TYPE_EDGE_FALLING>;
+					/*
+					 * The I2C bus is using a PCA9306 level translator from L16A
+					 * to L2B so these two voltages are needed and L16A is
+					 * kind of the IO voltage, however L16Aisn't really fed to
+					 * the TMA340, which relies entirely on L2B (PM8901 L2).
+					 */
+					vcpin-supply = <&pm8058_l16>;
+					vdd-supply = <&pm8901_l2>;
+					/* GPIO58, called WAKE_CTP */
+					reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>;
+					touchscreen-size-x = <480>;
+					touchscreen-size-y = <800>;
+					active-interval-ms = <0>;
+					touch-timeout-ms = <255>;
+					lowpower-interval-ms = <10>;
+					bootloader-key = /bits/ 8 <0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&dragon_tma340_gpios>;
+				};
+			};
+		};
+
+		gsbi@19800000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C>;
+
+			i2c@19880000 {
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi8_i2c_pins>;
+
+				eeprom@52 {
+					/* A 16KiB Platform ID EEPROM on the CPU carrier board */
+					compatible = "atmel,24c128";
+					reg = <0x52>;
+					vcc-supply = <&pm8058_s3>;
+					pagesize = <64>;
+				};
+				wm8903: wm8903@1a {
+					/* This Woolfson Micro device has an unrouted interrupt line */
+					compatible = "wlf,wm8903";
+					reg = <0x1a>;
+
+					AVDD-supply = <&pm8058_l16>;
+					CPVDD-supply = <&pm8058_l16>;
+					DBVDD-supply = <&pm8058_s3>;
+					DCVDD-supply = <&pm8058_l0>;
+
+					gpio-controller;
+					#gpio-cells = <2>;
+
+					micdet-cfg = <0>;
+					micdet-delay = <100>;
+					gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+				};
+			};
+		};
+
+		gsbi@19c00000 {
+			status = "okay";
+			qcom,mode = <GSBI_PROT_I2C_UART>;
+
+			serial@19c40000 {
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi12_serial_pins>;
+			};
+
+			i2c@19c80000 {
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_gsbi12_i2c_pins>;
+
+				ak8975@c {
+					compatible = "asahi-kasei,ak8975";
+					reg = <0x0c>;
+					interrupt-parent = <&pm8058_gpio>;
+					interrupts = <33 IRQ_TYPE_EDGE_RISING>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&dragon_ak8975_gpios>;
+					vid-supply = <&pm8058_lvs0>; // 1.8V
+					vdd-supply = <&pm8058_l14>; // 2.85V
+				};
+				bmp085@77 {
+					compatible = "bosch,bmp085";
+					reg = <0x77>;
+					interrupt-parent = <&pm8058_gpio>;
+					interrupts = <16 IRQ_TYPE_EDGE_RISING>;
+					reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&dragon_bmp085_gpios>;
+					vddd-supply = <&pm8058_lvs0>; // 1.8V
+					vdda-supply = <&pm8058_l14>; // 2.85V
+				};
+				mpu3050@68 {
+					compatible = "invensense,mpu3050";
+					reg = <0x68>;
+					/*
+					 * GPIO17 is pulled high by a 10k
+					 * resistor to VLOGIC so needs to be
+					 * active low/falling edge.
+					 */
+					interrupts-extended = <&pm8058_gpio 17 IRQ_TYPE_EDGE_FALLING>;
+					pinctrl-names = "default";
+					pinctrl-0 = <&dragon_mpu3050_gpios>;
+					vlogic-supply = <&pm8058_lvs0>; // 1.8V
+					vdd-supply = <&pm8058_l14>; // 2.85V
+
+					/*
+					 * The MPU-3050 acts as a hub for the
+					 * accelerometer.
+					 */
+					i2c-gate {
+						#address-cells = <1>;
+						#size-cells = <0>;
+
+						kxsd9@18 {
+							compatible = "kionix,kxsd9";
+							reg = <0x18>;
+							interrupt-parent = <&tlmm>;
+							interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
+							pinctrl-names = "default";
+							pinctrl-0 = <&dragon_kxsd9_gpios>;
+							iovdd-supply = <&pm8058_lvs0>; // 1.8V
+							vdd-supply = <&pm8058_l14>; // 2.85V
+						};
+					};
+				};
+			};
+		};
+
+		external-bus@1a100000 {
+			/* The EBI2 will instantiate first, then populate its children */
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dragon_ebi2_pins>;
+
+			/*
+			 * An on-board SMSC LAN9221 chip for "debug ethernet",
+			 * which is actually just an ordinary ethernet on the
+			 * EBI2. This has a 25MHz chrystal next to it, so no
+			 * clocking is needed.
+			 */
+			ethernet@2,0 {
+				compatible = "smsc,lan9221", "smsc,lan9115";
+				reg = <2 0x0 0x100>;
+				/*
+				 * The second interrupt is the PME interrupt
+				 * for network wakeup, connected to the TLMM.
+				 */
+				interrupts-extended = <&pm8058_gpio 7 IRQ_TYPE_EDGE_FALLING>,
+						    <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
+				reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
+				vdd33a-supply = <&dragon_veth>;
+				vddvario-supply = <&dragon_vario>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_ethernet_gpios>;
+				phy-mode = "mii";
+				reg-io-width = <2>;
+				smsc,force-external-phy;
+				smsc,irq-push-pull;
+
+				/*
+				 * SLOW chipselect config
+				 * Delay 9 cycles (140ns@64MHz) between SMSC
+				 * LAN9221 Ethernet controller reads and writes
+				 * on CS2.
+				 */
+				qcom,xmem-recovery-cycles = <0>;
+				qcom,xmem-write-hold-cycles = <3>;
+				qcom,xmem-write-delta-cycles = <31>;
+				qcom,xmem-read-delta-cycles = <28>;
+				qcom,xmem-write-wait-cycles = <9>;
+				qcom,xmem-read-wait-cycles = <9>;
+			};
+		};
+
+		rpm@104000 {
+			/*
+			 * Set up of the PMIC RPM regulators for this board
+			 * PM8901 supplies "preliminary regulators" whatever
+			 * that means
+			 */
+			pm8901-regulators {
+				vdd_l0-supply = <&pm8901_s4>;
+				vdd_l1-supply = <&vph>;
+				vdd_l2-supply = <&vph>;
+				vdd_l3-supply = <&vph>;
+				vdd_l4-supply = <&vph>;
+				vdd_l5-supply = <&vph>;
+				vdd_l6-supply = <&vph>;
+				/* vdd_s0-supply, vdd_s1-supply: SAW regulators */
+				vdd_s2-supply = <&vph>;
+				vdd_s3-supply = <&vph>;
+				vdd_s4-supply = <&vph>;
+				lvs0_in-supply = <&pm8058_s3>;
+				lvs1_in-supply = <&pm8901_s4>;
+				lvs2_in-supply = <&pm8058_l0>;
+				lvs3_in-supply = <&pm8058_s2>;
+				mvs_in-supply = <&pm8058_s3>;
+
+				l0 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l1 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+				l2 {
+					/* TMA340 requires strictly 3.3V */
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+				l3 {
+					regulator-min-microvolt = <3300000>;
+					regulator-max-microvolt = <3300000>;
+					bias-pull-down;
+				};
+				l4 {
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l5 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l6 {
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					bias-pull-down;
+				};
+
+				/* s0 and s1 are SAW regulators controlled over SPM */
+				s2 {
+					regulator-min-microvolt = <1300000>;
+					regulator-max-microvolt = <1300000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s3 {
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s4 {
+					regulator-min-microvolt = <1225000>;
+					regulator-max-microvolt = <1225000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+
+				/* LVS0 thru 3 and mvs are just switches */
+				lvs0 {
+					regulator-always-on;
+				};
+				lvs1 { };
+				lvs2 { };
+				lvs3 { };
+				mvs { };
+
+			};
+
+			pm8058-regulators {
+				vdd_l0_l1_lvs-supply = <&pm8058_s3>;
+				vdd_l2_l11_l12-supply = <&vph>;
+				vdd_l3_l4_l5-supply = <&vph>;
+				vdd_l6_l7-supply = <&vph>;
+				vdd_l8-supply = <&vph>;
+				vdd_l9-supply = <&vph>;
+				vdd_l10-supply = <&vph>;
+				vdd_l13_l16-supply = <&pm8058_s4>;
+				vdd_l14_l15-supply = <&vph>;
+				vdd_l17_l18-supply = <&vph>;
+				vdd_l19_l20-supply = <&vph>;
+				vdd_l21-supply = <&pm8058_s3>;
+				vdd_l22-supply = <&pm8058_s3>;
+				vdd_l23_l24_l25-supply = <&pm8058_s3>;
+				vdd_s0-supply = <&vph>;
+				vdd_s1-supply = <&vph>;
+				vdd_s2-supply = <&vph>;
+				vdd_s3-supply = <&vph>;
+				vdd_s4-supply = <&vph>;
+				vdd_ncp-supply = <&vph>;
+
+				l0 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l1 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l2 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l3 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l4 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l5 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l6 {
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3600000>;
+					bias-pull-down;
+				};
+				l7 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l8 {
+					regulator-min-microvolt = <2900000>;
+					regulator-max-microvolt = <3050000>;
+					bias-pull-down;
+				};
+				l9 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l10 {
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l11 {
+					regulator-min-microvolt = <1500000>;
+					regulator-max-microvolt = <1500000>;
+					bias-pull-down;
+				};
+				l12 {
+					regulator-min-microvolt = <2900000>;
+					regulator-max-microvolt = <2900000>;
+					bias-pull-down;
+				};
+				l13 {
+					regulator-min-microvolt = <2050000>;
+					regulator-max-microvolt = <2050000>;
+					bias-pull-down;
+				};
+				l14 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+				};
+				l15 {
+					regulator-min-microvolt = <2850000>;
+					regulator-max-microvolt = <2850000>;
+					bias-pull-down;
+				};
+				l16 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+				l17 {
+					// 1.5V according to schematic
+					regulator-min-microvolt = <2600000>;
+					regulator-max-microvolt = <2600000>;
+					bias-pull-down;
+				};
+				l18 {
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					bias-pull-down;
+				};
+				l19 {
+					regulator-min-microvolt = <2500000>;
+					regulator-max-microvolt = <2500000>;
+					bias-pull-down;
+				};
+				l20 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					bias-pull-down;
+				};
+				l21 {
+					// 1.1 V according to schematic
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+					regulator-always-on;
+				};
+				l22 {
+					// 1.2 V according to schematic
+					regulator-min-microvolt = <1150000>;
+					regulator-max-microvolt = <1150000>;
+					bias-pull-down;
+				};
+				l23 {
+					// Unused
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l24 {
+					// Unused
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+				l25 {
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					bias-pull-down;
+				};
+
+				s0 {
+					// regulator-min-microvolt = <500000>;
+					// regulator-max-microvolt = <1325000>;
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s1 {
+					// regulator-min-microvolt = <500000>;
+					// regulator-max-microvolt = <1250000>;
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s2 {
+					// 1.3 V according to schematic
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1400000>;
+					qcom,switch-mode-frequency = <1600000>;
+					bias-pull-down;
+				};
+				s3 {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+					regulator-always-on;
+					bias-pull-down;
+				};
+				s4 {
+					regulator-min-microvolt = <2200000>;
+					regulator-max-microvolt = <2200000>;
+					qcom,switch-mode-frequency = <1600000>;
+					regulator-always-on;
+					bias-pull-down;
+				};
+
+				/* LVS0 and LVS1 are just switches */
+				lvs0 {
+					bias-pull-down;
+				};
+				lvs1 {
+					bias-pull-down;
+				};
+
+				ncp {
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					qcom,switch-mode-frequency = <1600000>;
+				};
+			};
+		};
+		amba {
+			/* Internal 3.69 GiB eMMC */
+			mmc@12400000 {
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_sdcc1_pins>;
+				vmmc-supply = <&pm8901_l5>;
+				vqmmc-supply = <&pm8901_lvs0>;
+			};
+
+			/* External micro SD card, directly connected, pulled up to 2.85 V */
+			mmc@12180000 {
+				status = "okay";
+				/* Enable SSBI GPIO 22 as input, use for card detect */
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>;
+				cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>;
+				wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+				vmmc-supply = <&pm8058_l14>;
+			};
+
+			/*
+			 * Second external micro SD card, using two TXB104RGYR levelshifters
+			 * to lift from 1.8 V to 2.85 V
+			 */
+			mmc@12200000 {
+				status = "okay";
+				/* Enable SSBI GPIO 26 as input, use for card detect */
+				pinctrl-names = "default";
+				pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>;
+				cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>;
+				wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>;
+				vmmc-supply = <&pm8058_l14>;
+				vqmmc-supply = <&dragon_vio_txb>;
+			};
+		};
+	};
+};