Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 994 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
new file mode 100644
index 000000000..69387e875
--- /dev/null
+++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
@@ -0,0 +1,994 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Devicetree for the Samsung Galaxy S Advance GT-I9070 also known as Janice.
+ */
+
+/dts-v1/;
+#include "ste-db8500.dtsi"
+#include "ste-ab8500.dtsi"
+#include "ste-dbx5x0-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Samsung Galaxy S Advance (GT-I9070)";
+	compatible = "samsung,janice", "st-ericsson,u8500";
+
+	chosen {
+		stdout-path = &serial2;
+	};
+
+	battery: battery {
+		compatible = "samsung,eb535151vu";
+	};
+
+	thermal-zones {
+		battery-thermal {
+			/* This zone will be polled by the battery temperature code */
+			polling-delay = <0>;
+			polling-delay-passive = <0>;
+			thermal-sensors = <&bat_therm>;
+
+			trips {
+				battery-crit-hi {
+					temperature = <70000>;
+					hysteresis = <2000>;
+					type = "critical";
+				};
+			};
+		};
+	};
+
+	bat_therm: thermistor {
+		compatible = "samsung,1404-001221";
+		io-channels = <&gpadc 0x02>; /* BatTemp */
+		pullup-uv = <1800000>;
+		pullup-ohm = <230000>;
+		pulldown-ohm = <0>;
+		#thermal-sensor-cells = <0>;
+	};
+
+	/* External LDO for eMMC LDO VMEM_3V3 controlled by GPIO6 */
+	ldo_3v3_reg: regulator-gpio-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VMEM_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio0 6 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>; // FIXME
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&emmc_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchscreen.
+	 * One GPIO line controls two voltages of 3.3V and 1.8V
+	 * this line is known as "TSP_LDO_ON1" in the schematics.
+	 */
+	ldo_tsp_3v3_reg: regulator-gpio-tsp-ldo-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "LDO_TSP_A3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+	ldo_tsp_1v8_reg: regulator-gpio-tsp-ldo-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TSP_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO94 controls this regulator */
+		gpio = <&gpio2 30 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_en_default_mode>;
+	};
+
+	/*
+	 * External Ricoh "TSP" regulator for the touchkeys.
+	 * Two GPIO lines controls two voltages of 3.3V and 1.8V
+	 * TSP_LDO_ON2 controls VREG_TOUCHKEY_1V8
+	 * EN_LED_LDO controls VREG_KLED_3V3 (key LED)
+	 */
+	ldo_kled_3v3_reg: regulator-gpio-vreg-kled-3v3 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_KLED_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		/* GPIO68 controls this regulator */
+		gpio = <&gpio2 4 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&en_led_ldo_default_mode>;
+	};
+	ldo_touchkey_1v8_reg: regulator-gpio-vreg-touchkey-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_TOUCHKEY_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO89 controls this regulator */
+		gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
+		/* 70 ms power-on delay */
+		startup-delay-us = <70000>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&tsp_ldo_on2_default_mode>;
+	};
+
+
+	/*
+	 * External Ricoh RP152L010B-TR LCD LDO regulator for the display.
+	 * LCD_PWR_EN controls a 3.0V and 1.8V output.
+	 */
+	lcd_3v0_reg: regulator-gpio-lcd-3v0 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_3V0";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+	lcd_1v8_reg: regulator-gpio-lcd-1v8 {
+		compatible = "regulator-fixed";
+		/* Supplied in turn by VBAT */
+		regulator-name = "VREG_LCD_1V8";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		/* GPIO219 controls this regulator */
+		gpio = <&gpio6 27 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&lcd_pwr_en_default_mode>;
+	};
+
+	/*
+	 * This regulator is a GPIO line that drives the Broadcom WLAN
+	 * line WL_REG_ON high and enables the internal regulators
+	 * inside the chip. Unfortunatley it is erroneously named
+	 * WLAN_RST_N on the schematic but it is not a reset line.
+	 *
+	 * The voltage specified here is only used to determine the OCR mask,
+	 * the for the SDIO connector, the chip is actually connected
+	 * directly to VBAT.
+	 */
+	wl_reg: regulator-gpio-wlan {
+		compatible = "regulator-fixed";
+		regulator-name = "WL_REG_ON";
+		regulator-min-microvolt = <3000000>;
+		regulator-max-microvolt = <3000000>;
+		startup-delay-us = <100000>;
+		/* GPIO215 (WLAN_RST_N to WL_REG_ON) */
+		gpio = <&gpio6 23 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlan_ldo_en_default>;
+	};
+
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_keys_default_mode>;
+
+		button-home {
+			linux,code = <KEY_HOME>;
+			label = "HOME";
+			/* GPIO91 */
+			gpios = <&gpio2 27 GPIO_ACTIVE_LOW>;
+		};
+		button-volup {
+			linux,code = <KEY_VOLUMEUP>;
+			label = "VOL+";
+			/* GPIO67 */
+			gpios = <&gpio2 3 GPIO_ACTIVE_LOW>;
+		};
+		button-voldown {
+			linux,code = <KEY_VOLUMEDOWN>;
+			label = "VOL-";
+			/* GPIO92 */
+			gpios = <&gpio2 28 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	/* Richtek RT8515GQW Flash LED Driver IC */
+	flash {
+		compatible = "richtek,rt8515";
+		/* GPIO 140 */
+		enf-gpios = <&gpio4 12 GPIO_ACTIVE_HIGH>;
+		/* GPIO 141 */
+		ent-gpios = <&gpio4 13 GPIO_ACTIVE_HIGH>;
+		/*
+		 * RFS is 16 kOhm and RTS is 100 kOhm giving
+		 * the flash max current 343mA and torch max
+		 * current 55 mA.
+		 */
+		richtek,rfs-ohms = <16000>;
+		richtek,rts-ohms = <100000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&gpio_flash_default_mode>;
+
+		led {
+			function = LED_FUNCTION_FLASH;
+			color = <LED_COLOR_ID_WHITE>;
+			flash-max-timeout-us = <250000>;
+			flash-max-microamp = <343750>;
+			led-max-microamp = <55000>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO143 and GPIO144 also called "SUBPMU I2C" */
+	i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Yamaha YAS530 magnetometer */
+		magnetometer@2e {
+			compatible = "yamaha,yas530";
+			reg = <0x2e>;
+			/* VDD 3V */
+			vdd-supply = <&ab8500_ldo_aux1_reg>;
+			/* IOVDD 1.8V */
+			iovdd-supply = <&ab8500_ldo_aux2_reg>;
+			/* GPIO204 COMPASS_RST_N */
+			reset-gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&yas529_default>;
+		};
+		/* TODO: this should also be used by the NCP6914 Camera power management unit */
+	};
+
+	/*
+	 * These pins do have an spi controller, however the controller on
+	 * these pins is not the fully featured PL022 SSP/SPI block but the
+	 * ST Micro diet "PL023" version. One of the lacking features in
+	 * this derivative is 3wire support, so it cannot be used to drive
+	 * this panel interface. We have to use GPIO bit-banging instead.
+	 */
+	spi-gpio-0 {
+		compatible = "spi-gpio";
+		/* Clock on GPIO220 */
+		sck-gpios = <&gpio6 28 GPIO_ACTIVE_HIGH>;
+		/* MISO/MOSI on GPIO224 (no separate MISO pin) */
+		mosi-gpios = <&gpio7 0 GPIO_ACTIVE_HIGH>;
+		/* Chip select on GPIO223 */
+		cs-gpios = <&gpio6 31 GPIO_ACTIVE_LOW>;
+		num-chipselects = <1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&spi_gpio_0_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		panel@0 {
+			compatible = "samsung,s6e63m0";
+			reg = <0>;
+			vdd3-supply = <&lcd_3v0_reg>;
+			vci-supply = <&lcd_1v8_reg>;
+			/* Reset on GPIO139 */
+			reset-gpios = <&gpio4 11 GPIO_ACTIVE_LOW>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&panel_default_mode>;
+			spi-3wire;
+			/* TYPE 3: inverse clock polarity and phase */
+			spi-cpha;
+			spi-cpol;
+
+			port {
+				panel_in: endpoint {
+					remote-endpoint = <&display_out>;
+				};
+			};
+		};
+	};
+
+	/*
+	 * Current sense amplifier on the light sensor to convert current to
+	 * voltage. We do not know if this is the actual configuration. The
+	 * sense resistor value was found by calibrating in a room ambient
+	 * light with a second mobile phone light sensor as reference. If you
+	 * pry a Janice phone apart and inspect it you may figure this out.
+	 */
+	gp2a_shunt: current-sense-shunt {
+		compatible = "current-sense-shunt";
+		io-channels = <&gpadc 0x07>;
+		shunt-resistor-micro-ohms = <15000000>; /* 15 ohms c:a */
+		#io-channel-cells = <0>;
+		io-channel-ranges;
+	};
+
+	/* Bit-banged I2C on GPIO196 and GPIO197 also called "TOUCHKEY_I2C" */
+	i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 4 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		clock-frequency = <400000>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_1_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		touchkey@20 {
+			compatible = "coreriver,tc360-touchkey";
+			reg = <0x20>;
+			vdd-supply = <&ldo_kled_3v3_reg>;
+			vcc-supply = <&ldo_touchkey_1v8_reg>;
+			vddio-supply = <&ldo_touchkey_1v8_reg>;
+
+			/* Interrupt on GPIO 198 */
+			interrupt-parent = <&gpio6>;
+			interrupts = <6 IRQ_TYPE_EDGE_RISING>;
+
+			pinctrl-names = "default";
+			pinctrl-0 = <&touchkey_default_mode>;
+			linux,keycodes = <KEY_MENU KEY_BACK>;
+		};
+	};
+
+	/* Bit-banged I2C on GPIO201 and GPIO202 also called "MOT_I2C" */
+	i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio6 10 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio6 9 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_2_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* TODO: add the Immersion ISA1200 I2C device here */
+	};
+
+	/* Bit-banged I2C on GPIO151 and GPIO152 also called "NFC_I2C" */
+	i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio4 24 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio4 23 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2c_gpio_3_default>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		nfc@30 {
+			compatible = "nxp,pn547", "nxp,nxp-nci-i2c";
+			reg = <0x30>;
+			/* NFC IRQ on GPIO32 */
+			interrupt-parent = <&gpio1>;
+			interrupts = <0 IRQ_TYPE_EDGE_FALLING>;
+			/* GPIO 31 */
+			firmware-gpios = <&gpio0 31 GPIO_ACTIVE_HIGH>;
+			/* GPIO88 */
+			enable-gpios = <&gpio2 24 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&pn547_janice_default>;
+		};
+	};
+
+	soc {
+		/* External Micro SD slot */
+		mmc@80126000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			cap-sd-highspeed;
+			cap-mmc-highspeed;
+			st,sig-dir-cmd;
+			st,sig-dir-dat0;
+			st,sig-dir-dat2;
+			st,sig-pin-fbclk;
+			full-pwr-cycle;
+			/* MMC is powered by AUX3 1.2V .. 2.91V */
+			vmmc-supply = <&ab8500_ldo_aux3_reg>;
+			/* 2.9 V level translator is using AUX3 at 2.9 V as well */
+			vqmmc-supply = <&ab8500_ldo_aux3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc0_a_2_default>;
+			pinctrl-1 = <&mc0_a_2_sleep>;
+			cd-gpios  = <&gpio6 25 GPIO_ACTIVE_LOW>; // GPIO217
+			status = "okay";
+		};
+
+		/* WLAN SDIO channel */
+		mmc@80118000 {
+			arm,primecell-periphid = <0x10480180>;
+			max-frequency = <50000000>;
+			bus-width = <4>;
+			non-removable;
+			cap-sd-highspeed;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc1_a_2_default>;
+			pinctrl-1 = <&mc1_a_2_sleep>;
+			/*
+			 * GPIO-controlled voltage enablement: this drives
+			 * the WL_REG_ON line high when we use this device.
+			 * Represented as regulator to fill OCR mask.
+			 */
+			vmmc-supply = <&wl_reg>;
+
+			#address-cells = <1>;
+			#size-cells = <0>;
+			status = "okay";
+
+			wifi@1 {
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
+				reg = <1>;
+				/* GPIO216 WL_HOST_WAKE */
+				interrupt-parent = <&gpio6>;
+				interrupts = <24 IRQ_TYPE_EDGE_FALLING>;
+				interrupt-names = "host-wake";
+				pinctrl-names = "default";
+				pinctrl-0 = <&wlan_default_mode>;
+			};
+		};
+
+		/* eMMC */
+		mmc@80005000 {
+			arm,primecell-periphid = <0x10480180>;
+		        max-frequency = <50000000>;
+			bus-width = <8>;
+			non-removable;
+			cap-mmc-highspeed;
+			mmc-ddr-1_8v;
+			no-sdio;
+			no-sd;
+			vmmc-supply = <&ldo_3v3_reg>;
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&mc2_a_1_default>;
+			pinctrl-1 = <&mc2_a_1_sleep>;
+			status = "okay";
+		};
+
+		/* GBF (Bluetooth) UART */
+		uart@80120000 {
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u0_a_1_default>;
+			pinctrl-1 = <&u0_a_1_sleep>;
+			status = "okay";
+
+			bluetooth {
+				/* BCM4330B1 actually */
+				compatible = "brcm,bcm4330-bt";
+				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
+				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
+				/* BT_WAKE on GPIO199 */
+				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+				/* BT_HOST_WAKE on GPIO97 */
+				/* FIXME: convert to interrupt */
+				host-wakeup-gpios = <&gpio3 1 GPIO_ACTIVE_HIGH>;
+				/* BT_RST_N on GPIO209 */
+				reset-gpios = <&gpio6 17 GPIO_ACTIVE_LOW>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&bluetooth_default_mode>;
+			};
+		};
+
+		/* GPS UART */
+		uart@80121000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			/* CTS/RTS is not used, CTS is repurposed as GPIO */
+			pinctrl-0 = <&u1rxtx_a_1_default>;
+			pinctrl-1 = <&u1rxtx_a_1_sleep>;
+
+			gnss {
+				/*
+				 * The Low Noise Amplifier (LNA) power and enablement is controlled
+				 * autonomously by the GSD4t.
+				 * Janice has a SiRFstarIV-based GSD4t
+				 * Golden has a SiRFstarV 5t-based CSRG05TA03-ICJE-R.
+				 */
+				compatible = "csr,gsd4t";
+				/* GPS_RSTN on GPIO21 */
+				reset-gpios = <&gpio0 21 GPIO_ACTIVE_LOW>;
+				/* GPS_ON_OFF on GPIO96 */
+				sirf,onoff-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>;
+				/* GPS_1V8 (VSMPS2) */
+				vcc-supply = <&db8500_vsmps2_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&gsd4t_janice_default>;
+				/* According to /etc/sirfgps.conf */
+				current-speed = <460800>;
+			};
+		};
+
+		/* Debugging console UART connected to TSU6111RSVR (FSA880) */
+		uart@80007000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&u2rxtx_c_1_default>;
+			pinctrl-1 = <&u2rxtx_c_1_sleep>;
+		};
+
+		prcmu@80157000 {
+			ab8500 {
+				phy {
+					pinctrl-names = "default", "sleep";
+					pinctrl-0 = <&usb_a_1_default>;
+					pinctrl-1 = <&usb_a_1_sleep>;
+				};
+
+				ab8500_fg {
+					line-impedance-micro-ohms = <15000>;
+				};
+
+				regulator {
+					ab8500_ldo_aux1 {
+						/* Used for VDD for sensors */
+						regulator-name = "V-SENSORS-VDD";
+						regulator-min-microvolt = <3000000>;
+						regulator-max-microvolt = <3000000>;
+					};
+
+					ab8500_ldo_aux2 {
+						/* Used for VIO for sensors */
+						regulator-name = "V-SENSORS-VIO";
+						regulator-min-microvolt = <1800000>;
+						regulator-max-microvolt = <1800000>;
+					};
+
+					ab8500_ldo_aux3 {
+						/* Used for voltage for external MMC/SD card */
+						regulator-name = "V-MMC-SD";
+						regulator-min-microvolt = <1200000>;
+						regulator-max-microvolt = <2910000>;
+					};
+				};
+			};
+		};
+
+		/* I2C0 */
+		i2c@80004000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c0_a_1_default>;
+			pinctrl-1 = <&i2c0_a_1_sleep>;
+
+			proximity@44 {
+				/* Janice has the GP2AP002A00F with light sensor */
+				compatible = "sharp,gp2ap002a00f";
+				clock-frequency = <400000>;
+				reg = <0x44>;
+
+				interrupt-parent = <&gpio4>;
+				interrupts = <18 IRQ_TYPE_EDGE_FALLING>;
+				vdd-supply = <&ab8500_ldo_aux1_reg>;
+				vio-supply = <&ab8500_ldo_aux2_reg>;
+				/* ADC channel AUX2 to read ALSOUT ambient light sensor out */
+				io-channels = <&gp2a_shunt>;
+				io-channel-names = "alsout";
+				pinctrl-names = "default";
+				pinctrl-0 = <&gp2ap002_janice_default>;
+				/* B1 mode (arch/arm/mach-ux500/include/mach/gp2a.h) */
+				sharp,proximity-far-hysteresis = /bits/ 8 <0x40>;
+				sharp,proximity-close-hysteresis = /bits/ 8 <0x0f>;
+			};
+		};
+
+		/* I2C1 on GPIO16 and GPIO17 also called "MUS I2C" */
+		i2c@80122000 {
+			status = "okay";
+			pinctrl-names = "default","sleep";
+			pinctrl-0 = <&i2c1_b_2_default>;
+			pinctrl-1 = <&i2c1_b_2_sleep>;
+
+			/* Texas Instruments TSU6111 micro USB switch */
+			usb-switch@25 {
+				compatible = "ti,tsu6111";
+				reg = <0x25>;
+				/* Interrupt JACK_INT_N on GPIO95 */
+				interrupt-parent = <&gpio2>;
+				interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsu6111_janice_default>;
+			};
+		};
+
+		/* I2C2 on GPIO10 and GPIO11 also called "SENSORS I2C" */
+		i2c@80128000 {
+			status = "okay";
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c2_b_2_default>;
+			pinctrl-1 = <&i2c2_b_2_sleep>;
+
+			gyroscope@68 {
+				compatible = "invensense,mpu3050";
+				reg = <0x68>;
+				/* GPIO226 interrupt */
+				interrupt-parent = <&gpio7>;
+				interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
+				/* FIXME: no idea about this */
+				mount-matrix = "1", "0", "0",
+					       "0", "1", "0",
+					       "0", "0", "1";
+				vlogic-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+				vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+				pinctrl-names = "default";
+				pinctrl-0 = <&mpu3050_janice_default>;
+
+				/*
+				 * The MPU-3050 acts as a hub for the
+				 * accelerometer.
+				 */
+				i2c-gate {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					/* Bosch BMA222 accelerometer */
+					accelerometer@8 {
+						compatible = "bosch,bma222";
+						reg = <0x08>;
+						mount-matrix = "0", "-1", "0",
+							       "1", "0", "0",
+							       "0", "0", "1";
+						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
+						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
+					};
+				};
+			};
+		};
+
+		/* I2C3 */
+		i2c@80110000 {
+			status = "okay";
+
+			pinctrl-names = "default", "sleep";
+			pinctrl-0 = <&i2c3_c_2_default>;
+			pinctrl-1 = <&i2c3_c_2_sleep>;
+
+			/* Atmel mXT224E touchscreen */
+			touchscreen@4a {
+				compatible = "atmel,maxtouch";
+				reg = <0x4a>;
+				/* GPIO218 (TSP_INT_1V8) */
+				interrupt-parent = <&gpio6>;
+				interrupts = <26 IRQ_TYPE_EDGE_FALLING>;
+				/* VDDA is "analog supply", 2.57-3.47 V */
+				vdda-supply = <&ldo_tsp_3v3_reg>;
+				/* VDD is "digital supply" 1.71-3.47V */
+				vdd-supply = <&ldo_tsp_1v8_reg>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&tsp_default>;
+			};
+		};
+
+		mcde@a0350000 {
+			status = "okay";
+			pinctrl-names = "default";
+			pinctrl-0 = <&dpi_default_mode>;
+
+			port {
+				display_out: endpoint {
+					remote-endpoint = <&panel_in>;
+				};
+			};
+		};
+	};
+};
+
+&pinctrl {
+	/*
+	 * This extends the MC0_A_2 default config to include
+	 * the card detect GPIO217 line.
+	 */
+	sdi0 {
+		mc0_a_2_default {
+			default_cfg4 {
+				pins = "GPIO217_AH12"; /* card detect */
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	mcde {
+		dpi_default_mode: dpi_default {
+			default_mux1 {
+				/* Mux in all the data lines */
+				function = "lcd";
+				groups =
+					/* Data lines D0-D7 GPIO70..GPIO77 */
+					"lcd_d0_d7_a_1",
+					/* Data lines D8-D11 GPIO78..GPIO81 */
+					"lcd_d8_d11_a_1",
+					/* Data lines D12-D15 GPIO82..GPIO85 */
+					"lcd_d12_d15_a_1",
+					/* Data lines D16-D23 GPIO161..GPIO168 */
+					"lcd_d16_d23_b_1";
+			};
+			default_mux2 {
+				function = "lcda";
+				/* Clock line on GPIO150, DE, VSO, HSO on GPIO169..GPIO171 */
+				groups = "lcdaclk_b_1", "lcda_b_1";
+			};
+			/* Input, no pull-up is the default state for pins used for an alt function */
+			default_cfg1 {
+				pins = "GPIO150_C14", "GPIO169_D22", "GPIO170_C23", "GPIO171_D23";
+				ste,config = <&in_nopull>;
+			};
+		};
+	};
+	/* GPIO for panel reset control */
+	panel {
+		panel_default_mode: panel_default {
+			janice_cfg1 {
+				/* Reset line */
+				pins = "GPIO139_C9";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the eMMC */
+	emmc-ldo {
+		emmc_ldo_en_default_mode: emmc_ldo_default {
+			/* LDO enable on GPIO6 */
+			janice_cfg1 {
+				pins = "GPIO6_AF6";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchscreen */
+	tsp-ldo {
+		tsp_ldo_en_default_mode: tsp_ldo_default {
+			/* LDO enable on GPIO94 */
+			janice_cfg1 {
+				pins = "GPIO94_D7";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the key LED */
+	key-led {
+		en_led_ldo_default_mode: en_led_ldo_default {
+			/* EN_LED_LDO on GPIO68 */
+			janice_cfg1 {
+				pins = "GPIO68_E1";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the LDO regulator for the touchkeys */
+	touchkey-ldo {
+		tsp_ldo_on2_default_mode: tsp_ldo_on2_default {
+			/* TSP_LDO_ON2 on GPIO89 */
+			janice_cfg1 {
+				pins = "GPIO89_E6";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	touchkey {
+		touchkey_default_mode: touchkey_default {
+			janice_cfg1 {
+				/* Interrupt */
+				pins = "GPIO198_AG25";
+				ste,config = <&gpio_in_nopull>;
+			};
+			janice_cfg2 {
+				/* Reset, actually completely unused (not routed) */
+				pins = "GPIO205_AG23";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	/* GPIO that enabled the LDO regulator for the LCD display */
+	lcd-ldo {
+		lcd_pwr_en_default_mode: lcd_pwr_en_default {
+			/* LCD_PWR_EN on GPIO219 */
+			janice_cfg1 {
+				pins = "GPIO219_AG10";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* GPIO that enables the WLAN internal LDO regulators */
+	wlan-ldo {
+		wlan_ldo_en_default: wlan_ldo_default {
+			/* GPIO215 named WLAN_RST_N */
+			janice_cfg1 {
+				pins = "GPIO215_AH13";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* Flash and torch */
+	flash {
+		gpio_flash_default_mode: flash_default {
+			janice_cfg1 {
+				pins = "GPIO140_B11", "GPIO141_C12";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	/* GPIO keys */
+	gpio-keys {
+		gpio_keys_default_mode: gpio_keys_default {
+			skomer_cfg1 {
+				pins = "GPIO67_G2", /* VOL UP */
+				       "GPIO91_B6", /* HOME */
+				       "GPIO92_D6"; /* VOL DOWN */
+				ste,config = <&gpio_in_pu>;
+			};
+		};
+	};
+	/* Interrupt line for the Atmel MXT228 touchscreen */
+	tsp {
+		tsp_default: tsp_default {
+			janice_cfg1 {
+				pins = "GPIO218_AH11";	/* TSP_INT_1V8 */
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Reset line for the Yamaha YAS529 magnetometer */
+	yas529 {
+		yas529_default: yas529_janice {
+			janice_cfg1 {
+				pins = "GPIO204_AF23";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for light/proximity sensor GP2AP002 */
+	gp2ap002 {
+		gp2ap002_janice_default: gp2ap002_janice {
+			janice_cfg1 {
+				pins = "GPIO146_D13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* Interrupt line for Invensense MPU3050 gyroscope */
+	mpu3050 {
+		mpu3050_janice_default: mpu3050_janice {
+			janice_cfg1 {
+				/* GPIO226 used for IRQ */
+				pins = "GPIO226_AF8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for magnetometer and NCP6914 */
+	i2c-gpio-0 {
+		i2c_gpio_0_default: i2c_gpio_0 {
+			janice_cfg1 {
+				pins = "GPIO143_D12", "GPIO144_B13";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Cypress touchkeys */
+	i2c-gpio-1 {
+		i2c_gpio_1_default: i2c_gpio_1 {
+			janice_cfg1 {
+				pins = "GPIO196_AG26", "GPIO197_AH24";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the Immersion ISA1200 */
+	i2c-gpio-2 {
+		i2c_gpio_2_default: i2c_gpio_2 {
+			janice_cfg1 {
+				pins = "GPIO201_AF24", "GPIO202_AF25";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based I2C bus for the NFC */
+	i2c-gpio-3 {
+		i2c_gpio_3_default: i2c_gpio_3 {
+			janice_cfg1 {
+				pins = "GPIO151_D17", "GPIO152_D16";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	/* GPIO-based SPI bus for the display */
+	spi-gpio-0 {
+		spi_gpio_0_default: spi_gpio_0 {
+			janice_cfg1 {
+				pins = "GPIO220_AH10", "GPIO223_AH9", "GPIO224_AG9";
+				ste,config = <&gpio_out_hi>;
+			};
+			/* This pin is unused but belongs with this SPI block */
+			janice_cfg2 {
+				pins = "GPIO225_AG8";
+				ste,config = <&in_pd>;
+			};
+		};
+	};
+	wlan {
+		wlan_default_mode: wlan_default {
+			/* GPIO216 for WL_HOST_WAKE */
+			janice_cfg2 {
+				pins = "GPIO216_AG12";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+	bluetooth {
+		bluetooth_default_mode: bluetooth_default {
+			/* GPIO199 BT_WAKE and GPIO222 BT_VREG_ON */
+			janice_cfg1 {
+				pins = "GPIO199_AH23", "GPIO222_AJ9";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPIO97 BT_HOST_WAKE */
+			janice_cfg2 {
+				pins = "GPIO97_D9";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* GPIO209 BT_RST_N */
+			janice_cfg3 {
+				pins = "GPIO209_AG15";
+				ste,config = <&gpio_out_hi>;
+			};
+		};
+	};
+	/* Interrupt line for TI TSU6111 Micro USB switch */
+	tsu6111 {
+		tsu6111_janice_default: tsu6111_janice {
+			janice_cfg1 {
+				/* GPIO95 used for IRQ */
+				pins = "GPIO95_E8";
+				ste,config = <&gpio_in_nopull>;
+			};
+		};
+	};
+	nfc {
+		pn547_janice_default: pn547_janice {
+			/* Interrupt line */
+			janice_cfg1 {
+				pins = "GPIO32_V2";
+				ste,config = <&gpio_in_nopull>;
+			};
+			/* Enable and firmware GPIOs */
+			janice_cfg2 {
+				pins = "GPIO31_V3", "GPIO88_C4";
+				ste,config = <&gpio_out_lo>;
+			};
+		};
+	};
+	gsd4t {
+		gsd4t_janice_default: gsd4t_janice {
+			/* Reset line, start out asserted */
+			janice_cfg1 {
+				pins = "GPIO21_AB3";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* GPS_ON_OFF, start out deasserted (off) */
+			janice_cfg2 {
+				pins = "GPIO96_D8";
+				ste,config = <&gpio_out_lo>;
+			};
+			/* Unused power enablement line, used in R0.0 and R0.1 boards */
+			janice_cfg3 {
+				pins = "GPIO86_C6";
+				ste,config = <&gpio_in_pd>;
+			};
+		};
+	};
+};