Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 317 insertions, 0 deletions

diff --git a/arch/arm/mach-omap2/sram243x.S b/arch/arm/mach-omap2/sram243x.S
new file mode 100644
index 000000000..faf03b7f0
--- /dev/null
+++ b/arch/arm/mach-omap2/sram243x.S
@@ -0,0 +1,317 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/*
+ * linux/arch/arm/mach-omap2/sram243x.S
+ *
+ * Omap2 specific functions that need to be run in internal SRAM
+ *
+ * (C) Copyright 2004
+ * Texas Instruments, <www.ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * Richard Woodruff notes that any changes to this code must be carefully
+ * audited and tested to ensure that they don't cause a TLB miss while
+ * the SDRAM is inaccessible.  Such a situation will crash the system
+ * since it will cause the ARM MMU to attempt to walk the page tables.
+ * These crashes may be intermittent.
+ */
+#include <linux/linkage.h>
+
+#include <asm/assembler.h>
+
+#include "soc.h"
+#include "iomap.h"
+#include "prm2xxx.h"
+#include "cm2xxx.h"
+#include "sdrc.h"
+
+	.text
+
+	.align	3
+ENTRY(omap243x_sram_ddr_init)
+	stmfd	sp!, {r0 - r12, lr}	@ save registers on stack
+
+	mov	r12, r2			@ capture CS1 vs CS0
+	mov	r8, r3			@ capture force parameter
+
+	/* frequency shift down */
+	ldr	r2, omap243x_sdi_cm_clksel2_pll	@ get address of dpllout reg
+	mov	r3, #0x1		@ value for 1x operation
+	str	r3, [r2]		@ go to L1-freq operation
+
+	/* voltage shift down */
+	mov r9, #0x1			@ set up for L1 voltage call
+	bl voltage_shift		@ go drop voltage
+
+	/* dll lock mode */
+	ldr	r11, omap243x_sdi_sdrc_dlla_ctrl	@ addr of dlla ctrl
+	ldr	r10, [r11]		@ get current val
+	cmp	r12, #0x1		@ cs1 base (2422 es2.05/1)
+	addeq	r11, r11, #0x8		@ if cs1 base, move to DLLB
+	mvn	r9, #0x4		@ mask to get clear bit2
+	and	r10, r10, r9		@ clear bit2 for lock mode.
+	orr	r10, r10, #0x8		@ make sure DLL on (es2 bit pos)
+	orr	r10, r10, #0x2		@ 90 degree phase for all below 133MHz
+	str	r10, [r11]		@ commit to DLLA_CTRL
+	bl	i_dll_wait		@ wait for dll to lock
+
+	/* get dll value */
+	add	r11, r11, #0x4		@ get addr of status reg
+	ldr	r10, [r11]		@ get locked value
+
+	/* voltage shift up */
+	mov r9, #0x0			@ shift back to L0-voltage
+	bl voltage_shift		@ go raise voltage
+
+	/* frequency shift up */
+	mov	r3, #0x2		@ value for 2x operation
+	str	r3, [r2]		@ go to L0-freq operation
+
+	/* reset entry mode for dllctrl */
+	sub	r11, r11, #0x4		@ move from status to ctrl
+	cmp	r12, #0x1		@ normalize if cs1 based
+	subeq	r11, r11, #0x8		@ possibly back to DLLA
+	cmp	r8, #0x1		@ if forced unlock exit
+	orreq	r1, r1, #0x4		@ make sure exit with unlocked value
+	str	r1, [r11]		@ restore DLLA_CTRL high value
+	add	r11, r11, #0x8		@ move to DLLB_CTRL addr
+	str	r1, [r11]		@ set value DLLB_CTRL
+	bl	i_dll_wait		@ wait for possible lock
+
+	/* set up for return, DDR should be good */
+	str r10, [r0]			@ write dll_status and return counter
+	ldmfd	sp!, {r0 - r12, pc}	@ restore regs and return
+
+	/* ensure the DLL has relocked */
+i_dll_wait:
+	mov	r4, #0x800		@ delay DLL relock, min 0x400 L3 clocks
+i_dll_delay:
+	subs	r4, r4, #0x1
+	bne	i_dll_delay
+	ret	lr
+
+	/*
+	 * shift up or down voltage, use R9 as input to tell level.
+	 * wait for it to finish, use 32k sync counter, 1tick=31uS.
+	 */
+voltage_shift:
+	ldr	r4, omap243x_sdi_prcm_voltctrl	@ get addr of volt ctrl.
+	ldr	r5, [r4]		@ get value.
+	ldr	r6, prcm_mask_val	@ get value of mask
+	and	r5, r5, r6		@ apply mask to clear bits
+	orr	r5, r5, r9		@ bulld value for L0/L1-volt operation.
+	str	r5, [r4]		@ set up for change.
+	mov	r3, #0x4000		@ get val for force
+	orr	r5, r5, r3		@ build value for force
+	str	r5, [r4]		@ Force transition to L1
+
+	ldr	r3, omap243x_sdi_timer_32ksynct_cr	@ get addr of counter
+	ldr	r5, [r3]		@ get value
+	add	r5, r5, #0x3		@ give it at most 93uS
+volt_delay:
+	ldr	r7, [r3]		@ get timer value
+	cmp	r5, r7			@ time up?
+	bhi	volt_delay		@ not yet->branch
+	ret	lr			@ back to caller.
+
+omap243x_sdi_cm_clksel2_pll:
+	.word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
+omap243x_sdi_sdrc_dlla_ctrl:
+	.word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+omap243x_sdi_prcm_voltctrl:
+	.word OMAP2430_PRCM_VOLTCTRL
+prcm_mask_val:
+	.word 0xFFFF3FFC
+omap243x_sdi_timer_32ksynct_cr:
+	.word OMAP2_L4_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
+ENTRY(omap243x_sram_ddr_init_sz)
+	.word	. - omap243x_sram_ddr_init
+
+/*
+ * Reprograms memory timings.
+ * r0 = [PRCM_FULL | PRCM_HALF] r1 = SDRC_DLLA_CTRL value r2 = [DDR | SDR]
+ * PRCM_FULL = 2, PRCM_HALF = 1, DDR = 1, SDR = 0
+ */
+	.align	3
+ENTRY(omap243x_sram_reprogram_sdrc)
+	stmfd	sp!, {r0 - r10, lr}	@ save registers on stack
+	mov	r3, #0x0		@ clear for mrc call
+	mcr	p15, 0, r3, c7, c10, 4	@ memory barrier, finish ARM SDR/DDR
+	nop
+	nop
+	ldr	r6, omap243x_srs_sdrc_rfr_ctrl	@ get addr of refresh reg
+	ldr	r5, [r6]		@ get value
+	mov	r5, r5, lsr #8		@ isolate rfr field and drop burst
+
+	cmp	r0, #0x1		@ going to half speed?
+	movne	r9, #0x0		@ if up set flag up for pre up, hi volt
+
+	blne	voltage_shift_c		@ adjust voltage
+
+	cmp	r0, #0x1		@ going to half speed (post branch link)
+	moveq	r5, r5, lsr #1		@ divide by 2 if to half
+	movne	r5, r5, lsl #1		@ mult by 2 if to full
+	mov	r5, r5, lsl #8		@ put rfr field back into place
+	add	r5, r5, #0x1		@ turn on burst of 1
+	ldr	r4, omap243x_srs_cm_clksel2_pll	@ get address of out reg
+	ldr	r3, [r4]		@ get curr value
+	orr	r3, r3, #0x3
+	bic	r3, r3, #0x3		@ clear lower bits
+	orr	r3, r3, r0		@ new state value
+	str	r3, [r4]		@ set new state (pll/x, x=1 or 2)
+	nop
+	nop
+
+	moveq	r9, #0x1		@ if speed down, post down, drop volt
+	bleq	voltage_shift_c
+
+	mcr	p15, 0, r3, c7, c10, 4	@ memory barrier
+	str	r5, [r6]		@ set new RFR_1 value
+	add	r6, r6, #0x30		@ get RFR_2 addr
+	str	r5, [r6]		@ set RFR_2
+	nop
+	cmp	r2, #0x1		@ (SDR or DDR) do we need to adjust DLL
+	bne	freq_out		@ leave if SDR, no DLL function
+
+	/* With DDR, we need to take care of the DLL for the frequency change */
+	ldr	r2, omap243x_srs_sdrc_dlla_ctrl	@ addr of dlla ctrl
+	str	r1, [r2]		@ write out new SDRC_DLLA_CTRL
+	add	r2, r2, #0x8		@ addr to SDRC_DLLB_CTRL
+	str	r1, [r2]		@ commit to SDRC_DLLB_CTRL
+	mov	r1, #0x2000		@ wait DLL relock, min 0x400 L3 clocks
+dll_wait:
+	subs	r1, r1, #0x1
+	bne	dll_wait
+freq_out:
+	ldmfd	sp!, {r0 - r10, pc}	@ restore regs and return
+
+    /*
+     * shift up or down voltage, use R9 as input to tell level.
+     *	wait for it to finish, use 32k sync counter, 1tick=31uS.
+     */
+voltage_shift_c:
+	ldr	r10, omap243x_srs_prcm_voltctrl	@ get addr of volt ctrl
+	ldr	r8, [r10]		@ get value
+	ldr	r7, ddr_prcm_mask_val	@ get value of mask
+	and	r8, r8, r7		@ apply mask to clear bits
+	orr	r8, r8, r9		@ bulld value for L0/L1-volt operation.
+	str	r8, [r10]		@ set up for change.
+	mov	r7, #0x4000		@ get val for force
+	orr	r8, r8, r7		@ build value for force
+	str	r8, [r10]		@ Force transition to L1
+
+	ldr	r10, omap243x_srs_timer_32ksynct	@ get addr of counter
+	ldr	r8, [r10]		@ get value
+	add	r8, r8, #0x2		@ give it at most 62uS (min 31+)
+volt_delay_c:
+	ldr	r7, [r10]		@ get timer value
+	cmp	r8, r7			@ time up?
+	bhi	volt_delay_c		@ not yet->branch
+	ret	lr			@ back to caller
+
+omap243x_srs_cm_clksel2_pll:
+	.word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
+omap243x_srs_sdrc_dlla_ctrl:
+	.word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+omap243x_srs_sdrc_rfr_ctrl:
+	.word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
+omap243x_srs_prcm_voltctrl:
+	.word OMAP2430_PRCM_VOLTCTRL
+ddr_prcm_mask_val:
+	.word 0xFFFF3FFC
+omap243x_srs_timer_32ksynct:
+	.word OMAP2_L4_IO_ADDRESS(OMAP2430_32KSYNCT_BASE + 0x010)
+
+ENTRY(omap243x_sram_reprogram_sdrc_sz)
+	.word	. - omap243x_sram_reprogram_sdrc
+
+/*
+ * Set dividers and pll. Also recalculate DLL value for DDR and unlock mode.
+ */
+	.align	3
+ENTRY(omap243x_sram_set_prcm)
+	stmfd	sp!, {r0-r12, lr}	@ regs to stack
+	adr	r4, pbegin		@ addr of preload start
+	adr	r8, pend		@ addr of preload end
+	mcrr	p15, 1, r8, r4, c12	@ preload into icache
+pbegin:
+	/* move into fast relock bypass */
+	ldr	r8, omap243x_ssp_pll_ctl	@ get addr
+	ldr	r5, [r8]		@ get val
+	mvn	r6, #0x3		@ clear mask
+	and	r5, r5, r6		@ clear field
+	orr	r7, r5, #0x2		@ fast relock val
+	str	r7, [r8]		@ go to fast relock
+	ldr	r4, omap243x_ssp_pll_stat	@ addr of stat
+block:
+	/* wait for bypass */
+	ldr	r8, [r4]		@ stat value
+	and	r8, r8, #0x3		@ mask for stat
+	cmp	r8, #0x1		@ there yet
+	bne	block			@ loop if not
+
+	/* set new dpll dividers _after_ in bypass */
+	ldr	r4, omap243x_ssp_pll_div	@ get addr
+	str	r0, [r4]		@ set dpll ctrl val
+
+	ldr	r4, omap243x_ssp_set_config	@ get addr
+	mov	r8, #1			@ valid cfg msk
+	str	r8, [r4]		@ make dividers take
+
+	mov	r4, #100		@ dead spin a bit
+wait_a_bit:
+	subs	r4, r4, #1		@ dec loop
+	bne	wait_a_bit		@ delay done?
+
+	/* check if staying in bypass */
+	cmp	r2, #0x1		@ stay in bypass?
+	beq	pend			@ jump over dpll relock
+
+	/* relock DPLL with new vals */
+	ldr	r5, omap243x_ssp_pll_stat	@ get addr
+	ldr	r4, omap243x_ssp_pll_ctl	@ get addr
+	orr	r8, r7, #0x3		@ val for lock dpll
+	str	r8, [r4]		@ set val
+	mov	r0, #1000		@ dead spin a bit
+wait_more:
+	subs	r0, r0, #1		@ dec loop
+	bne	wait_more		@ delay done?
+wait_lock:
+	ldr	r8, [r5]		@ get lock val
+	and	r8, r8, #3		@ isolate field
+	cmp	r8, #2			@ locked?
+	bne	wait_lock		@ wait if not
+pend:
+	/* update memory timings & briefly lock dll */
+	ldr	r4, omap243x_ssp_sdrc_rfr	@ get addr
+	str	r1, [r4]		@ update refresh timing
+	ldr	r11, omap243x_ssp_dlla_ctrl	@ get addr of DLLA ctrl
+	ldr	r10, [r11]		@ get current val
+	mvn	r9, #0x4		@ mask to get clear bit2
+	and	r10, r10, r9		@ clear bit2 for lock mode
+	orr	r10, r10, #0x8		@ make sure DLL on (es2 bit pos)
+	str	r10, [r11]		@ commit to DLLA_CTRL
+	add	r11, r11, #0x8		@ move to dllb
+	str	r10, [r11]		@ hit DLLB also
+
+	mov	r4, #0x800		@ relock time (min 0x400 L3 clocks)
+wait_dll_lock:
+	subs	r4, r4, #0x1
+	bne	wait_dll_lock
+	nop
+	ldmfd	sp!, {r0-r12, pc}	@ restore regs and return
+
+omap243x_ssp_set_config:
+	.word OMAP2430_PRCM_CLKCFG_CTRL
+omap243x_ssp_pll_ctl:
+	.word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKEN)
+omap243x_ssp_pll_stat:
+	.word OMAP2430_CM_REGADDR(PLL_MOD, CM_IDLEST)
+omap243x_ssp_pll_div:
+	.word OMAP2430_CM_REGADDR(PLL_MOD, CM_CLKSEL1)
+omap243x_ssp_sdrc_rfr:
+	.word OMAP243X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
+omap243x_ssp_dlla_ctrl:
+	.word OMAP243X_SDRC_REGADDR(SDRC_DLLA_CTRL)
+
+ENTRY(omap243x_sram_set_prcm_sz)
+	.word	. - omap243x_sram_set_prcm