Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 393 insertions, 0 deletions

diff --git a/drivers/cpufreq/speedstep-smi.c b/drivers/cpufreq/speedstep-smi.c
new file mode 100644
index 000000000..0ce9d4b6d
--- /dev/null
+++ b/drivers/cpufreq/speedstep-smi.c
@@ -0,0 +1,393 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Intel SpeedStep SMI driver.
+ *
+ * (C) 2003  Hiroshi Miura <miura@da-cha.org>
+ */
+
+
+/*********************************************************************
+ *                        SPEEDSTEP - DEFINITIONS                    *
+ *********************************************************************/
+
+#define pr_fmt(fmt) "cpufreq: " fmt
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <asm/ist.h>
+#include <asm/cpu_device_id.h>
+
+#include "speedstep-lib.h"
+
+/* speedstep system management interface port/command.
+ *
+ * These parameters are got from IST-SMI BIOS call.
+ * If user gives it, these are used.
+ *
+ */
+static int smi_port;
+static int smi_cmd;
+static unsigned int smi_sig;
+
+/* info about the processor */
+static enum speedstep_processor speedstep_processor;
+
+/*
+ * There are only two frequency states for each processor. Values
+ * are in kHz for the time being.
+ */
+static struct cpufreq_frequency_table speedstep_freqs[] = {
+	{0, SPEEDSTEP_HIGH,	0},
+	{0, SPEEDSTEP_LOW,	0},
+	{0, 0,			CPUFREQ_TABLE_END},
+};
+
+#define GET_SPEEDSTEP_OWNER 0
+#define GET_SPEEDSTEP_STATE 1
+#define SET_SPEEDSTEP_STATE 2
+#define GET_SPEEDSTEP_FREQS 4
+
+/* how often shall the SMI call be tried if it failed, e.g. because
+ * of DMA activity going on? */
+#define SMI_TRIES 5
+
+/**
+ * speedstep_smi_ownership
+ */
+static int speedstep_smi_ownership(void)
+{
+	u32 command, result, magic, dummy;
+	u32 function = GET_SPEEDSTEP_OWNER;
+	unsigned char magic_data[] = "Copyright (c) 1999 Intel Corporation";
+
+	command = (smi_sig & 0xffffff00) | (smi_cmd & 0xff);
+	magic = virt_to_phys(magic_data);
+
+	pr_debug("trying to obtain ownership with command %x at port %x\n",
+			command, smi_port);
+
+	__asm__ __volatile__(
+		"push %%ebp\n"
+		"out %%al, (%%dx)\n"
+		"pop %%ebp\n"
+		: "=D" (result),
+		  "=a" (dummy), "=b" (dummy), "=c" (dummy), "=d" (dummy),
+		  "=S" (dummy)
+		: "a" (command), "b" (function), "c" (0), "d" (smi_port),
+		  "D" (0), "S" (magic)
+		: "memory"
+	);
+
+	pr_debug("result is %x\n", result);
+
+	return result;
+}
+
+/**
+ * speedstep_smi_get_freqs - get SpeedStep preferred & current freq.
+ * @low: the low frequency value is placed here
+ * @high: the high frequency value is placed here
+ *
+ * Only available on later SpeedStep-enabled systems, returns false results or
+ * even hangs [cf. bugme.osdl.org # 1422] on earlier systems. Empirical testing
+ * shows that the latter occurs if !(ist_info.event & 0xFFFF).
+ */
+static int speedstep_smi_get_freqs(unsigned int *low, unsigned int *high)
+{
+	u32 command, result = 0, edi, high_mhz, low_mhz, dummy;
+	u32 state = 0;
+	u32 function = GET_SPEEDSTEP_FREQS;
+
+	if (!(ist_info.event & 0xFFFF)) {
+		pr_debug("bug #1422 -- can't read freqs from BIOS\n");
+		return -ENODEV;
+	}
+
+	command = (smi_sig & 0xffffff00) | (smi_cmd & 0xff);
+
+	pr_debug("trying to determine frequencies with command %x at port %x\n",
+			command, smi_port);
+
+	__asm__ __volatile__(
+		"push %%ebp\n"
+		"out %%al, (%%dx)\n"
+		"pop %%ebp"
+		: "=a" (result),
+		  "=b" (high_mhz),
+		  "=c" (low_mhz),
+		  "=d" (state), "=D" (edi), "=S" (dummy)
+		: "a" (command),
+		  "b" (function),
+		  "c" (state),
+		  "d" (smi_port), "S" (0), "D" (0)
+	);
+
+	pr_debug("result %x, low_freq %u, high_freq %u\n",
+			result, low_mhz, high_mhz);
+
+	/* abort if results are obviously incorrect... */
+	if ((high_mhz + low_mhz) < 600)
+		return -EINVAL;
+
+	*high = high_mhz * 1000;
+	*low  = low_mhz  * 1000;
+
+	return result;
+}
+
+/**
+ * speedstep_set_state - set the SpeedStep state
+ * @state: new processor frequency state (SPEEDSTEP_LOW or SPEEDSTEP_HIGH)
+ *
+ */
+static void speedstep_set_state(unsigned int state)
+{
+	unsigned int result = 0, command, new_state, dummy;
+	unsigned long flags;
+	unsigned int function = SET_SPEEDSTEP_STATE;
+	unsigned int retry = 0;
+
+	if (state > 0x1)
+		return;
+
+	/* Disable IRQs */
+	preempt_disable();
+	local_irq_save(flags);
+
+	command = (smi_sig & 0xffffff00) | (smi_cmd & 0xff);
+
+	pr_debug("trying to set frequency to state %u "
+		"with command %x at port %x\n",
+		state, command, smi_port);
+
+	do {
+		if (retry) {
+			/*
+			 * We need to enable interrupts, otherwise the blockage
+			 * won't resolve.
+			 *
+			 * We disable preemption so that other processes don't
+			 * run. If other processes were running, they could
+			 * submit more DMA requests, making the blockage worse.
+			 */
+			pr_debug("retry %u, previous result %u, waiting...\n",
+					retry, result);
+			local_irq_enable();
+			mdelay(retry * 50);
+			local_irq_disable();
+		}
+		retry++;
+		__asm__ __volatile__(
+			"push %%ebp\n"
+			"out %%al, (%%dx)\n"
+			"pop %%ebp"
+			: "=b" (new_state), "=D" (result),
+			  "=c" (dummy), "=a" (dummy),
+			  "=d" (dummy), "=S" (dummy)
+			: "a" (command), "b" (function), "c" (state),
+			  "d" (smi_port), "S" (0), "D" (0)
+			);
+	} while ((new_state != state) && (retry <= SMI_TRIES));
+
+	/* enable IRQs */
+	local_irq_restore(flags);
+	preempt_enable();
+
+	if (new_state == state)
+		pr_debug("change to %u MHz succeeded after %u tries "
+			"with result %u\n",
+			(speedstep_freqs[new_state].frequency / 1000),
+			retry, result);
+	else
+		pr_err("change to state %u failed with new_state %u and result %u\n",
+		       state, new_state, result);
+
+	return;
+}
+
+
+/**
+ * speedstep_target - set a new CPUFreq policy
+ * @policy: new policy
+ * @index: index of new freq
+ *
+ * Sets a new CPUFreq policy/freq.
+ */
+static int speedstep_target(struct cpufreq_policy *policy, unsigned int index)
+{
+	speedstep_set_state(index);
+
+	return 0;
+}
+
+
+static int speedstep_cpu_init(struct cpufreq_policy *policy)
+{
+	int result;
+	unsigned int *low, *high;
+
+	/* capability check */
+	if (policy->cpu != 0)
+		return -ENODEV;
+
+	result = speedstep_smi_ownership();
+	if (result) {
+		pr_debug("fails in acquiring ownership of a SMI interface.\n");
+		return -EINVAL;
+	}
+
+	/* detect low and high frequency */
+	low = &speedstep_freqs[SPEEDSTEP_LOW].frequency;
+	high = &speedstep_freqs[SPEEDSTEP_HIGH].frequency;
+
+	result = speedstep_smi_get_freqs(low, high);
+	if (result) {
+		/* fall back to speedstep_lib.c dection mechanism:
+		 * try both states out */
+		pr_debug("could not detect low and high frequencies "
+				"by SMI call.\n");
+		result = speedstep_get_freqs(speedstep_processor,
+				low, high,
+				NULL,
+				&speedstep_set_state);
+
+		if (result) {
+			pr_debug("could not detect two different speeds"
+					" -- aborting.\n");
+			return result;
+		} else
+			pr_debug("workaround worked.\n");
+	}
+
+	policy->freq_table = speedstep_freqs;
+
+	return 0;
+}
+
+static unsigned int speedstep_get(unsigned int cpu)
+{
+	if (cpu)
+		return -ENODEV;
+	return speedstep_get_frequency(speedstep_processor);
+}
+
+
+static int speedstep_resume(struct cpufreq_policy *policy)
+{
+	int result = speedstep_smi_ownership();
+
+	if (result)
+		pr_debug("fails in re-acquiring ownership of a SMI interface.\n");
+
+	return result;
+}
+
+static struct cpufreq_driver speedstep_driver = {
+	.name		= "speedstep-smi",
+	.flags		= CPUFREQ_NO_AUTO_DYNAMIC_SWITCHING,
+	.verify		= cpufreq_generic_frequency_table_verify,
+	.target_index	= speedstep_target,
+	.init		= speedstep_cpu_init,
+	.get		= speedstep_get,
+	.resume		= speedstep_resume,
+	.attr		= cpufreq_generic_attr,
+};
+
+static const struct x86_cpu_id ss_smi_ids[] = {
+	X86_MATCH_VENDOR_FAM_MODEL(INTEL,  6, 0x8, 0),
+	X86_MATCH_VENDOR_FAM_MODEL(INTEL,  6, 0xb, 0),
+	X86_MATCH_VENDOR_FAM_MODEL(INTEL, 15, 0x2, 0),
+	{}
+};
+
+/**
+ * speedstep_init - initializes the SpeedStep CPUFreq driver
+ *
+ *   Initializes the SpeedStep support. Returns -ENODEV on unsupported
+ * BIOS, -EINVAL on problems during initiatization, and zero on
+ * success.
+ */
+static int __init speedstep_init(void)
+{
+	if (!x86_match_cpu(ss_smi_ids))
+		return -ENODEV;
+
+	speedstep_processor = speedstep_detect_processor();
+
+	switch (speedstep_processor) {
+	case SPEEDSTEP_CPU_PIII_T:
+	case SPEEDSTEP_CPU_PIII_C:
+	case SPEEDSTEP_CPU_PIII_C_EARLY:
+		break;
+	default:
+		speedstep_processor = 0;
+	}
+
+	if (!speedstep_processor) {
+		pr_debug("No supported Intel CPU detected.\n");
+		return -ENODEV;
+	}
+
+	pr_debug("signature:0x%.8x, command:0x%.8x, "
+		"event:0x%.8x, perf_level:0x%.8x.\n",
+		ist_info.signature, ist_info.command,
+		ist_info.event, ist_info.perf_level);
+
+	/* Error if no IST-SMI BIOS or no PARM
+		 sig= 'ISGE' aka 'Intel Speedstep Gate E' */
+	if ((ist_info.signature !=  0x47534943) && (
+	    (smi_port == 0) || (smi_cmd == 0)))
+		return -ENODEV;
+
+	if (smi_sig == 1)
+		smi_sig = 0x47534943;
+	else
+		smi_sig = ist_info.signature;
+
+	/* setup smi_port from MODLULE_PARM or BIOS */
+	if ((smi_port > 0xff) || (smi_port < 0))
+		return -EINVAL;
+	else if (smi_port == 0)
+		smi_port = ist_info.command & 0xff;
+
+	if ((smi_cmd > 0xff) || (smi_cmd < 0))
+		return -EINVAL;
+	else if (smi_cmd == 0)
+		smi_cmd = (ist_info.command >> 16) & 0xff;
+
+	return cpufreq_register_driver(&speedstep_driver);
+}
+
+
+/**
+ * speedstep_exit - unregisters SpeedStep support
+ *
+ *   Unregisters SpeedStep support.
+ */
+static void __exit speedstep_exit(void)
+{
+	cpufreq_unregister_driver(&speedstep_driver);
+}
+
+module_param_hw(smi_port, int, ioport, 0444);
+module_param(smi_cmd,  int, 0444);
+module_param(smi_sig, uint, 0444);
+
+MODULE_PARM_DESC(smi_port, "Override the BIOS-given IST port with this value "
+		"-- Intel's default setting is 0xb2");
+MODULE_PARM_DESC(smi_cmd, "Override the BIOS-given IST command with this value "
+		"-- Intel's default setting is 0x82");
+MODULE_PARM_DESC(smi_sig, "Set to 1 to fake the IST signature when using the "
+		"SMI interface.");
+
+MODULE_AUTHOR("Hiroshi Miura");
+MODULE_DESCRIPTION("Speedstep driver for IST applet SMI interface.");
+MODULE_LICENSE("GPL");
+
+module_init(speedstep_init);
+module_exit(speedstep_exit);