Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 218 insertions, 0 deletions

diff --git a/drivers/gpio/gpio-xra1403.c b/drivers/gpio/gpio-xra1403.c
new file mode 100644
index 000000000..49c878cfd
--- /dev/null
+++ b/drivers/gpio/gpio-xra1403.c
@@ -0,0 +1,218 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * GPIO driver for EXAR XRA1403 16-bit GPIO expander
+ *
+ * Copyright (c) 2017, General Electric Company
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio/driver.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
+#include <linux/seq_file.h>
+#include <linux/spi/spi.h>
+#include <linux/regmap.h>
+
+/* XRA1403 registers */
+#define XRA_GSR   0x00 /* GPIO State */
+#define XRA_OCR   0x02 /* Output Control */
+#define XRA_PIR   0x04 /* Input Polarity Inversion */
+#define XRA_GCR   0x06 /* GPIO Configuration */
+#define XRA_PUR   0x08 /* Input Internal Pull-up Resistor Enable/Disable */
+#define XRA_IER   0x0A /* Input Interrupt Enable */
+#define XRA_TSCR  0x0C /* Output Three-State Control */
+#define XRA_ISR   0x0E /* Input Interrupt Status */
+#define XRA_REIR  0x10 /* Input Rising Edge Interrupt Enable */
+#define XRA_FEIR  0x12 /* Input Falling Edge Interrupt Enable */
+#define XRA_IFR   0x14 /* Input Filter Enable/Disable */
+#define XRA_LAST  0x15 /* Bounds */
+
+struct xra1403 {
+	struct gpio_chip  chip;
+	struct regmap     *regmap;
+};
+
+static const struct regmap_config xra1403_regmap_cfg = {
+		.reg_bits = 7,
+		.pad_bits = 1,
+		.val_bits = 8,
+
+		.max_register = XRA_LAST,
+};
+
+static unsigned int to_reg(unsigned int reg, unsigned int offset)
+{
+	return reg + (offset > 7);
+}
+
+static int xra1403_direction_input(struct gpio_chip *chip, unsigned int offset)
+{
+	struct xra1403 *xra = gpiochip_get_data(chip);
+
+	return regmap_update_bits(xra->regmap, to_reg(XRA_GCR, offset),
+			BIT(offset % 8), BIT(offset % 8));
+}
+
+static int xra1403_direction_output(struct gpio_chip *chip, unsigned int offset,
+				    int value)
+{
+	int ret;
+	struct xra1403 *xra = gpiochip_get_data(chip);
+
+	ret = regmap_update_bits(xra->regmap, to_reg(XRA_GCR, offset),
+			BIT(offset % 8), 0);
+	if (ret)
+		return ret;
+
+	ret = regmap_update_bits(xra->regmap, to_reg(XRA_OCR, offset),
+			BIT(offset % 8), value ? BIT(offset % 8) : 0);
+
+	return ret;
+}
+
+static int xra1403_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	int ret;
+	unsigned int val;
+	struct xra1403 *xra = gpiochip_get_data(chip);
+
+	ret = regmap_read(xra->regmap, to_reg(XRA_GCR, offset), &val);
+	if (ret)
+		return ret;
+
+	if (val & BIT(offset % 8))
+		return GPIO_LINE_DIRECTION_IN;
+
+	return GPIO_LINE_DIRECTION_OUT;
+}
+
+static int xra1403_get(struct gpio_chip *chip, unsigned int offset)
+{
+	int ret;
+	unsigned int val;
+	struct xra1403 *xra = gpiochip_get_data(chip);
+
+	ret = regmap_read(xra->regmap, to_reg(XRA_GSR, offset), &val);
+	if (ret)
+		return ret;
+
+	return !!(val & BIT(offset % 8));
+}
+
+static void xra1403_set(struct gpio_chip *chip, unsigned int offset, int value)
+{
+	int ret;
+	struct xra1403 *xra = gpiochip_get_data(chip);
+
+	ret = regmap_update_bits(xra->regmap, to_reg(XRA_OCR, offset),
+			BIT(offset % 8), value ? BIT(offset % 8) : 0);
+	if (ret)
+		dev_err(chip->parent, "Failed to set pin: %d, ret: %d\n",
+				offset, ret);
+}
+
+#ifdef CONFIG_DEBUG_FS
+static void xra1403_dbg_show(struct seq_file *s, struct gpio_chip *chip)
+{
+	int reg;
+	struct xra1403 *xra = gpiochip_get_data(chip);
+	int value[XRA_LAST];
+	int i;
+	const char *label;
+	unsigned int gcr;
+	unsigned int gsr;
+
+	seq_puts(s, "xra reg:");
+	for (reg = 0; reg <= XRA_LAST; reg++)
+		seq_printf(s, " %2.2x", reg);
+	seq_puts(s, "\n  value:");
+	for (reg = 0; reg < XRA_LAST; reg++) {
+		regmap_read(xra->regmap, reg, &value[reg]);
+		seq_printf(s, " %2.2x", value[reg]);
+	}
+	seq_puts(s, "\n");
+
+	gcr = value[XRA_GCR + 1] << 8 | value[XRA_GCR];
+	gsr = value[XRA_GSR + 1] << 8 | value[XRA_GSR];
+	for_each_requested_gpio(chip, i, label) {
+		seq_printf(s, " gpio-%-3d (%-12s) %s %s\n",
+			   chip->base + i, label,
+			   (gcr & BIT(i)) ? "in" : "out",
+			   (gsr & BIT(i)) ? "hi" : "lo");
+	}
+}
+#else
+#define xra1403_dbg_show NULL
+#endif
+
+static int xra1403_probe(struct spi_device *spi)
+{
+	struct xra1403 *xra;
+	struct gpio_desc *reset_gpio;
+	int ret;
+
+	xra = devm_kzalloc(&spi->dev, sizeof(*xra), GFP_KERNEL);
+	if (!xra)
+		return -ENOMEM;
+
+	/* bring the chip out of reset if reset pin is provided*/
+	reset_gpio = devm_gpiod_get_optional(&spi->dev, "reset", GPIOD_OUT_LOW);
+	if (IS_ERR(reset_gpio))
+		dev_warn(&spi->dev, "Could not get reset-gpios\n");
+
+	xra->chip.direction_input = xra1403_direction_input;
+	xra->chip.direction_output = xra1403_direction_output;
+	xra->chip.get_direction = xra1403_get_direction;
+	xra->chip.get = xra1403_get;
+	xra->chip.set = xra1403_set;
+
+	xra->chip.dbg_show = xra1403_dbg_show;
+
+	xra->chip.ngpio = 16;
+	xra->chip.label = "xra1403";
+
+	xra->chip.base = -1;
+	xra->chip.can_sleep = true;
+	xra->chip.parent = &spi->dev;
+	xra->chip.owner = THIS_MODULE;
+
+	xra->regmap = devm_regmap_init_spi(spi, &xra1403_regmap_cfg);
+	if (IS_ERR(xra->regmap)) {
+		ret = PTR_ERR(xra->regmap);
+		dev_err(&spi->dev, "Failed to allocate regmap: %d\n", ret);
+		return ret;
+	}
+
+	return devm_gpiochip_add_data(&spi->dev, &xra->chip, xra);
+}
+
+static const struct spi_device_id xra1403_ids[] = {
+	{ "xra1403" },
+	{},
+};
+MODULE_DEVICE_TABLE(spi, xra1403_ids);
+
+static const struct of_device_id xra1403_spi_of_match[] = {
+	{ .compatible = "exar,xra1403" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, xra1403_spi_of_match);
+
+static struct spi_driver xra1403_driver = {
+	.probe    = xra1403_probe,
+	.id_table = xra1403_ids,
+	.driver   = {
+		.name           = "xra1403",
+		.of_match_table = of_match_ptr(xra1403_spi_of_match),
+	},
+};
+
+module_spi_driver(xra1403_driver);
+
+MODULE_AUTHOR("Nandor Han <nandor.han@ge.com>");
+MODULE_AUTHOR("Semi Malinen <semi.malinen@ge.com>");
+MODULE_DESCRIPTION("GPIO expander driver for EXAR XRA1403");
+MODULE_LICENSE("GPL v2");