Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 155 insertions, 0 deletions

diff --git a/drivers/mtd/nand/raw/r852.h b/drivers/mtd/nand/raw/r852.h
new file mode 100644
index 000000000..96fe301d1
--- /dev/null
+++ b/drivers/mtd/nand/raw/r852.h
@@ -0,0 +1,155 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright © 2009 - Maxim Levitsky
+ * driver for Ricoh xD readers
+ */
+
+#include <linux/pci.h>
+#include <linux/completion.h>
+#include <linux/workqueue.h>
+#include <linux/mtd/rawnand.h>
+#include <linux/spinlock.h>
+
+
+/* nand interface + ecc
+   byte write/read does one cycle on nand data lines.
+   dword write/read does 4 cycles
+   if R852_CTL_ECC_ACCESS is set in R852_CTL, then dword read reads
+   results of ecc correction, if DMA read was done before.
+   If write was done two dword reads read generated ecc checksums
+*/
+#define	R852_DATALINE		0x00
+
+/* control register */
+#define R852_CTL		0x04
+#define R852_CTL_COMMAND 	0x01	/* send command (#CLE)*/
+#define R852_CTL_DATA		0x02	/* read/write data (#ALE)*/
+#define R852_CTL_ON		0x04	/* only seem to controls the hd led, */
+					/* but has to be set on start...*/
+#define R852_CTL_RESET		0x08	/* unknown, set only on start once*/
+#define R852_CTL_CARDENABLE	0x10	/* probably (#CE) - always set*/
+#define R852_CTL_ECC_ENABLE	0x20	/* enable ecc engine */
+#define R852_CTL_ECC_ACCESS	0x40	/* read/write ecc via reg #0*/
+#define R852_CTL_WRITE		0x80	/* set when performing writes (#WP) */
+
+/* card detection status */
+#define R852_CARD_STA		0x05
+
+#define R852_CARD_STA_CD	0x01	/* state of #CD line, same as 0x04 */
+#define R852_CARD_STA_RO	0x02	/* card is readonly */
+#define R852_CARD_STA_PRESENT	0x04	/* card is present (#CD) */
+#define R852_CARD_STA_ABSENT	0x08	/* card is absent */
+#define R852_CARD_STA_BUSY	0x80	/* card is busy - (#R/B) */
+
+/* card detection irq status & enable*/
+#define R852_CARD_IRQ_STA	0x06	/* IRQ status */
+#define R852_CARD_IRQ_ENABLE	0x07	/* IRQ enable */
+
+#define R852_CARD_IRQ_CD	0x01	/* fire when #CD lights, same as 0x04*/
+#define R852_CARD_IRQ_REMOVE	0x04	/* detect card removal */
+#define R852_CARD_IRQ_INSERT	0x08	/* detect card insert */
+#define R852_CARD_IRQ_UNK1	0x10	/* unknown */
+#define R852_CARD_IRQ_GENABLE	0x80	/* general enable */
+#define R852_CARD_IRQ_MASK	0x1D
+
+
+
+/* hardware enable */
+#define R852_HW			0x08
+#define R852_HW_ENABLED		0x01	/* hw enabled */
+#define R852_HW_UNKNOWN		0x80
+
+
+/* dma capabilities */
+#define R852_DMA_CAP		0x09
+#define R852_SMBIT		0x20	/* if set with bit #6 or bit #7, then */
+					/* hw is smartmedia */
+#define R852_DMA1		0x40	/* if set w/bit #7, dma is supported */
+#define R852_DMA2		0x80	/* if set w/bit #6, dma is supported */
+
+
+/* physical DMA address - 32 bit value*/
+#define R852_DMA_ADDR		0x0C
+
+
+/* dma settings */
+#define R852_DMA_SETTINGS	0x10
+#define R852_DMA_MEMORY		0x01	/* (memory <-> internal hw buffer) */
+#define R852_DMA_READ		0x02	/* 0 = write, 1 = read */
+#define R852_DMA_INTERNAL	0x04	/* (internal hw buffer <-> card) */
+
+/* dma IRQ status */
+#define R852_DMA_IRQ_STA		0x14
+
+/* dma IRQ enable */
+#define R852_DMA_IRQ_ENABLE	0x18
+
+#define R852_DMA_IRQ_MEMORY	0x01	/* (memory <-> internal hw buffer) */
+#define R852_DMA_IRQ_ERROR	0x02	/* error did happen */
+#define R852_DMA_IRQ_INTERNAL	0x04	/* (internal hw buffer <-> card) */
+#define R852_DMA_IRQ_MASK	0x07	/* mask of all IRQ bits */
+
+
+/* ECC syndrome format - read from reg #0 will return two copies of these for
+   each half of the page.
+   first byte is error byte location, and second, bit location + flags */
+#define R852_ECC_ERR_BIT_MSK	0x07	/* error bit location */
+#define R852_ECC_CORRECT		0x10	/* no errors - (guessed) */
+#define R852_ECC_CORRECTABLE	0x20	/* correctable error exist */
+#define R852_ECC_FAIL		0x40	/* non correctable error detected */
+
+#define R852_DMA_LEN		512
+
+#define DMA_INTERNAL	0
+#define DMA_MEMORY	1
+
+struct r852_device {
+	struct nand_controller		controller;
+	void __iomem *mmio;		/* mmio */
+	struct nand_chip *chip;		/* nand chip backpointer */
+	struct pci_dev *pci_dev;	/* pci backpointer */
+
+	/* dma area */
+	dma_addr_t phys_dma_addr;	/* bus address of buffer*/
+	struct completion dma_done;	/* data transfer done */
+
+	dma_addr_t phys_bounce_buffer;	/* bus address of bounce buffer */
+	uint8_t *bounce_buffer;		/* virtual address of bounce buffer */
+
+	int dma_dir;			/* 1 = read, 0 = write */
+	int dma_stage;			/* 0 - idle, 1 - first step,
+					   2 - second step */
+
+	int dma_state;			/* 0 = internal, 1 = memory */
+	int dma_error;			/* dma errors */
+	int dma_usable;			/* is it possible to use dma */
+
+	/* card status area */
+	struct delayed_work card_detect_work;
+	struct workqueue_struct *card_workqueue;
+	int card_registered;		/* card registered with mtd */
+	int card_detected;		/* card detected in slot */
+	int card_unstable;		/* whenever the card is inserted,
+					   is not known yet */
+	int readonly;			/* card is readonly */
+	int sm;				/* Is card smartmedia */
+
+	/* interrupt handling */
+	spinlock_t irqlock;		/* IRQ protecting lock */
+	int irq;			/* irq num */
+	/* misc */
+	void *tmp_buffer;		/* temporary buffer */
+	uint8_t ctlreg;			/* cached contents of control reg */
+};
+
+#define dbg(format, ...) \
+	if (debug) \
+		pr_debug(format "\n", ## __VA_ARGS__)
+
+#define dbg_verbose(format, ...) \
+	if (debug > 1) \
+		pr_debug(format "\n", ## __VA_ARGS__)
+
+
+#define message(format, ...) \
+	pr_info(format "\n", ## __VA_ARGS__)