diff options
Diffstat (limited to 'Documentation/driver-api/media/tx-rx.rst')
| -rw-r--r-- | Documentation/driver-api/media/tx-rx.rst | 133 |
1 files changed, 133 insertions, 0 deletions
diff --git a/Documentation/driver-api/media/tx-rx.rst b/Documentation/driver-api/media/tx-rx.rst new file mode 100644 index 000000000..e1e9258dd --- /dev/null +++ b/Documentation/driver-api/media/tx-rx.rst @@ -0,0 +1,133 @@ +.. SPDX-License-Identifier: GPL-2.0 + +.. _transmitter-receiver: + +Pixel data transmitter and receiver drivers +=========================================== + +V4L2 supports various devices that transmit and receive pixel data. Examples of +these devices include a camera sensor, a TV tuner and a parallel or a CSI-2 +receiver in an SoC. + +Bus types +--------- + +The following busses are the most common. This section discusses these two only. + +MIPI CSI-2 +^^^^^^^^^^ + +CSI-2 is a data bus intended for transferring images from cameras to +the host SoC. It is defined by the `MIPI alliance`_. + +.. _`MIPI alliance`: https://www.mipi.org/ + +Parallel +^^^^^^^^ + +`BT.601`_ and `BT.656`_ are the most common parallel busses. + +.. _`BT.601`: https://en.wikipedia.org/wiki/Rec._601 +.. _`BT.656`: https://en.wikipedia.org/wiki/ITU-R_BT.656 + +Transmitter drivers +------------------- + +Transmitter drivers generally need to provide the receiver drivers with the +configuration of the transmitter. What is required depends on the type of the +bus. These are common for both busses. + +Media bus pixel code +^^^^^^^^^^^^^^^^^^^^ + +See :ref:`v4l2-mbus-pixelcode`. + +Link frequency +^^^^^^^^^^^^^^ + +The :ref:`V4L2_CID_LINK_FREQ <v4l2-cid-link-freq>` control is used to tell the +receiver the frequency of the bus (i.e. it is not the same as the symbol rate). + +``.s_stream()`` callback +^^^^^^^^^^^^^^^^^^^^^^^^ + +The struct struct v4l2_subdev_video_ops->s_stream() callback is used by the +receiver driver to control the transmitter driver's streaming state. + + +CSI-2 transmitter drivers +------------------------- + +Pixel rate +^^^^^^^^^^ + +The pixel rate on the bus is calculated as follows:: + + pixel_rate = link_freq * 2 * nr_of_lanes * 16 / k / bits_per_sample + +where + +.. list-table:: variables in pixel rate calculation + :header-rows: 1 + + * - variable or constant + - description + * - link_freq + - The value of the ``V4L2_CID_LINK_FREQ`` integer64 menu item. + * - nr_of_lanes + - Number of data lanes used on the CSI-2 link. This can + be obtained from the OF endpoint configuration. + * - 2 + - Data is transferred on both rising and falling edge of the signal. + * - bits_per_sample + - Number of bits per sample. + * - k + - 16 for D-PHY and 7 for C-PHY + +.. note:: + + The pixel rate calculated this way is **not** the same thing as the + pixel rate on the camera sensor's pixel array which is indicated by the + :ref:`V4L2_CID_PIXEL_RATE <v4l2-cid-pixel-rate>` control. + +LP-11 and LP-111 modes +^^^^^^^^^^^^^^^^^^^^^^ + +As part of transitioning to high speed mode, a CSI-2 transmitter typically +briefly sets the bus to LP-11 or LP-111 state, depending on the PHY. This period +may be as short as 100 µs, during which the receiver observes this state and +proceeds its own part of high speed mode transition. + +Most receivers are capable of autonomously handling this once the software has +configured them to do so, but there are receivers which require software +involvement in observing LP-11 or LP-111 state. 100 µs is a brief period to hit +in software, especially when there is no interrupt telling something is +happening. + +One way to address this is to configure the transmitter side explicitly to LP-11 +or LP-111 mode, which requires support from the transmitter hardware. This is +not universally available. Many devices return to this state once streaming is +stopped while the state after power-on is LP-00 or LP-000. + +The ``.pre_streamon()`` callback may be used to prepare a transmitter for +transitioning to streaming state, but not yet start streaming. Similarly, the +``.post_streamoff()`` callback is used to undo what was done by the +``.pre_streamon()`` callback. The caller of ``.pre_streamon()`` is thus required +to call ``.post_streamoff()`` for each successful call of ``.pre_streamon()``. + +In the context of CSI-2, the ``.pre_streamon()`` callback is used to transition +the transmitter to the LP-11 or LP-111 mode. This also requires powering on the +device, so this should be only done when it is needed. + +Receiver drivers that do not need explicit LP-11 or LP-111 mode setup are waived +from calling the two callbacks. + +Stopping the transmitter +^^^^^^^^^^^^^^^^^^^^^^^^ + +A transmitter stops sending the stream of images as a result of +calling the ``.s_stream()`` callback. Some transmitters may stop the +stream at a frame boundary whereas others stop immediately, +effectively leaving the current frame unfinished. The receiver driver +should not make assumptions either way, but function properly in both +cases. |