1 files changed, 134 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
new file mode 100644
index 000000000..f1f8eee13
--- /dev/null
+++ b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi
@@ -0,0 +1,134 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Marvell RD88F6181 Common Board descrition
+ *
+ * Andrew Lunn <andrew@lunn.ch>
+ *
+ * This file contains the definitions that are common between the two
+ * variants of the Marvell Kirkwood Development Board.
+ */
+
+#include "kirkwood.dtsi"
+#include "kirkwood-6281.dtsi"
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x20000000>;
+	};
+
+	chosen {
+		bootargs = "console=ttyS0,115200n8";
+		stdout-path = &uart0;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pinctrl-names = "default";
+
+			pmx_sdio_cd: pmx-sdio-cd {
+				marvell,pins = "mpp28";
+				marvell,function = "gpio";
+			};
+		};
+
+		serial@12000 {
+			status = "okay";
+
+		};
+
+		sata@80000 {
+			status = "okay";
+			nr-ports = <2>;
+		};
+		mvsdio@90000 {
+			pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>;
+			pinctrl-names = "default";
+			status = "okay";
+			cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>;
+			/* No WP GPIO */
+		};
+       };
+};
+
+&nand {
+	status = "okay";
+
+	partition@0 {
+		label = "u-boot";
+		reg = <0x0000000 0x100000>;
+		read-only;
+	};
+
+	partition@100000 {
+		label = "uImage";
+		reg = <0x0100000 0x200000>;
+	};
+
+	partition@300000 {
+		label = "rootfs";
+		reg = <0x0300000 0x500000>;
+	};
+};
+
+&mdio {
+	status = "okay";
+
+	switch: switch@0 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan4";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+				ethernet = <&eth0port>;
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+		};
+	};
+};
+
+&eth0 {
+	status = "okay";
+	ethernet0-port@0 {
+		speed = <1000>;
+		duplex = <1>;
+	};
+};
+
+&pciec {
+        status = "okay";
+};
+
+&pcie0 {
+	status = "okay";
+};