diff options
Diffstat (limited to 'arch/arm/boot/dts/pxa300-raumfeld-controller.dts')
| -rw-r--r-- | arch/arm/boot/dts/pxa300-raumfeld-controller.dts | 285 |
1 files changed, 285 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/pxa300-raumfeld-controller.dts b/arch/arm/boot/dts/pxa300-raumfeld-controller.dts new file mode 100644 index 000000000..12b15945a --- /dev/null +++ b/arch/arm/boot/dts/pxa300-raumfeld-controller.dts @@ -0,0 +1,285 @@ +// SPDX-License-Identifier: GPL-2.0 + +/dts-v1/; + +#include "pxa300-raumfeld-common.dtsi" + +/ { + model = "Raumfeld Controller (PXA3xx)"; + compatible = "raumfeld,raumfeld-controller-pxa303", "marvell,pxa300"; + + reg_vbatt: regulator-vbatt { + compatible = "regulator-fixed"; + regulator-name = "vbatt-fixed-supply"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + regulator-always-on; + }; + + lcd_supply: regulator-va-tft { + compatible = "regulator-fixed"; + regulator-name = "va-tft-fixed-supply"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio 33 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + onewire { + compatible = "w1-gpio"; + pinctrl-names = "default"; + pinctrl-0 = <&w1_pins>; + gpios = < + &gpio 126 GPIO_OPEN_DRAIN /* W1 I/O */ + &gpio 105 GPIO_ACTIVE_HIGH /* pullup */ + >; + + w1_ds2760: slave-ds2760 { + compatible = "maxim,ds2760"; + power-supplies = <&charger>; + }; + }; + + charger: charger { + pinctrl-names = "default"; + pinctrl-0 = <&charger_pins>; + compatible = "gpio-charger"; + charger-type = "mains"; + gpios = <&gpio 101 GPIO_ACTIVE_LOW>; + }; + + /* + * One of the following two will be set to "okay" by the bootloader, + * depending on the hardware revision. + */ + backlight-controller-pwm { + compatible = "pwm-backlight"; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pins>; + pwms = <&pwm0 10000>; + power-supply = <®_vbatt>; + status = "disabled"; + + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <100>; + }; + + backlight-controller { + compatible = "lltc,lt3593"; + pinctrl-names = "default"; + pinctrl-0 = <<3593_pins>; + lltc,ctrl-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + status = "disabled"; + + led { + label = "backlight"; + default-state = "on"; + }; + }; +}; + +®_va_5v0 { + status = "disabled"; +}; + +ðernet { + status = "disabled"; +}; + +&leds { + status = "disabled"; +}; + +&dac { + status = "disabled"; +}; + +&pwm0 { + status = "okay"; +}; + +&keys { + pinctrl-0 = <&gpio_keys_pins &dock_detect_pins>; + dock-detect { + label = "dock detect"; + gpios = <&gpio 116 GPIO_ACTIVE_LOW>; + linux,code = <KEY_F5>; + }; +}; + +&spi { + accelerometer@1 { + compatible = "st,lis302dl-spi"; + pinctrl-names = "default"; + pinctrl-0 = <&lis302_pins>; + reg = <1>; + spi-max-frequency = <1000000>; + interrupt-parent = <&gpio>; + interrupts = <104 IRQ_TYPE_EDGE_FALLING>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + }; +}; + +&lcdc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&lcdc_pins>; + lcd-supply = <&lcd_supply>; + + port { + lcdc_out: endpoint { + remote-endpoint = <&panel_in>; + bus-width = <16>; + }; + }; + + panel { + compatible = "sharp,lq043t3dx0-panel"; + display-timings { + native-mode = <&timing0>; + timing0: timing { + clock-frequency = <9009000>; + pixelclk-active = <0>; /* negative edge */ + hactive = <480>; + vactive = <272>; + hsync-len = <41>; + hback-porch = <2>; + hfront-porch = <1>; + vsync-len = <10>; + vback-porch = <3>; + vfront-porch = <1>; + }; + }; + + port { + panel_in: endpoint { + remote-endpoint = <&lcdc_out>; + }; + }; + }; +}; + +&gcu { + status = "okay"; +}; + +&pxai2c1 { + touchscreen@a { + compatible = "eeti,exc3000-i2c"; + pinctrl-names = "default"; + pinctrl-0 = <&eeti_ts_pins>; + reg = <0xa>; + interrupt-parent = <&gpio>; + interrupts = <32 IRQ_TYPE_EDGE_RISING>; + attn-gpios = <&gpio 32 GPIO_ACTIVE_HIGH>; + touchscreen-inverted-y; + }; +}; + +&pinctrl { + lis302_pins: lis302-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(104) MFP_AF0 /* IRQ */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + eeti_ts_pins: eeti-ts-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(32) MFP_AF0 /* IRQ */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + lt3593_pins: lt3593-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(17) MFP_AF0 /* Backlight */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + pwm0_pins: pwm0-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(17) MFP_AF1 /* PWM */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; + + w1_pins: w1-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(126) MFP_AF0 /* PWM */ + MFP_PIN_PXA300(105) MFP_AF0 /* PWM */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_FLOAT); + }; + + charger_pins: charger_pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(31) MFP_AF0 /* PEN2 */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_HIGH); + pinctrl-single,bias-pullup = MPF_PULL_UP; + }; + + dock_detect_pins: dock_detect_pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(116) MFP_AF0 /* DOCK_DETECT */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_HIGH); + pinctrl-single,bias-pullup = MPF_PULL_UP; + }; + + lcdc_pins: lcdc-pins { + pinctrl-single,pins = < + MFP_PIN_PXA300(54) MFP_AF1 /* LDD_0 */ + MFP_PIN_PXA300(55) MFP_AF1 /* LDD_1 */ + MFP_PIN_PXA300(56) MFP_AF1 /* LDD_2 */ + MFP_PIN_PXA300(57) MFP_AF1 /* LDD_3 */ + MFP_PIN_PXA300(58) MFP_AF1 /* LDD_4 */ + MFP_PIN_PXA300(59) MFP_AF1 /* LDD_5 */ + MFP_PIN_PXA300(60) MFP_AF1 /* LDD_6 */ + MFP_PIN_PXA300(61) MFP_AF1 /* LDD_7 */ + MFP_PIN_PXA300(62) MFP_AF1 /* LDD_8 */ + MFP_PIN_PXA300(63) MFP_AF1 /* LDD_9 */ + MFP_PIN_PXA300(64) MFP_AF1 /* LDD_10 */ + MFP_PIN_PXA300(65) MFP_AF1 /* LDD_11 */ + MFP_PIN_PXA300(66) MFP_AF1 /* LDD_12 */ + MFP_PIN_PXA300(67) MFP_AF1 /* LDD_13 */ + MFP_PIN_PXA300(68) MFP_AF1 /* LDD_14 */ + MFP_PIN_PXA300(69) MFP_AF1 /* LDD_15 */ + MFP_PIN_PXA300(70) MFP_AF1 /* LDD_16 */ + MFP_PIN_PXA300(71) MFP_AF1 /* LDD_17 */ + MFP_PIN_PXA300(72) MFP_AF1 /* LCD_FCLK */ + MFP_PIN_PXA300(73) MFP_AF1 /* LCD_LCLK */ + MFP_PIN_PXA300(74) MFP_AF1 /* LCD_PCLK */ + MFP_PIN_PXA300(75) MFP_AF1 /* LCD_BIAS */ + >; + pinctrl-single,low-power-mode = MFP_LPM(MFP_LPM_PULL_LOW); + }; +}; |