diff options
Diffstat (limited to 'arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi | 169 |
1 files changed, 169 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi new file mode 100644 index 000000000..35b1034aa --- /dev/null +++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-drc02.dtsi @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause +/* + * Copyright (C) 2020 Marek Vasut <marex@denx.de> + */ + +#include <dt-bindings/input/input.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + aliases { + serial0 = &uart4; + serial1 = &usart3; + serial2 = &uart8; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&adc { + status = "disabled"; +}; + +&dac { + status = "disabled"; +}; + +&gpiob { + /* + * NOTE: On DRC02, the RS485_RX_En is controlled by a separate + * GPIO line, however the STM32 UART driver assumes RX happens + * during TX anyway and that it only controls drive enable DE + * line. Hence, the RX is always enabled here. + */ + rs485-rx-en-hog { + gpio-hog; + gpios = <8 0>; + output-low; + line-name = "rs485-rx-en"; + }; +}; + +&gpiod { + gpio-line-names = "", "", "", "", + "", "", "DHCOM-B", "", + "", "", "", "DRC02-Out1", + "DRC02-Out2", "", "", ""; +}; + +&gpioi { + gpio-line-names = "DRC02-In1", "DHCOM-O", "DHCOM-H", "DHCOM-I", + "DHCOM-R", "DHCOM-M", "", "", + "DRC02-In2", "", "", "", + "", "", "", ""; + + /* + * NOTE: The USB Hub on the DRC02 needs a reset signal to be + * pulled high in order to be detected by the USB Controller. + * This signal should be handled by USB power sequencing in + * order to reset the Hub when USB bus is powered down, but + * so far there is no such functionality. + */ + usb-hub-hog { + gpio-hog; + gpios = <2 0>; + output-high; + line-name = "usb-hub-reset"; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; + + eeprom@50 { + compatible = "atmel,24c04"; + reg = <0x50>; + pagesize = <16>; + }; +}; + +&i2c4 { + touchscreen@49 { + status = "disabled"; + }; +}; + +&i2c5 { /* TP7/TP8 */ + pinctrl-names = "default"; + pinctrl-0 = <&i2c5_pins_a>; + i2c-scl-rising-time-ns = <185>; + i2c-scl-falling-time-ns = <20>; + status = "okay"; + /* spare dmas for other usage */ + /delete-property/dmas; + /delete-property/dma-names; +}; + +&sdmmc3 { + /* + * On DRC02, the SoM does not have SDIO WiFi. The pins + * are used for on-board microSD slot instead. + */ + /delete-property/broken-cd; + cd-gpios = <&gpioi 10 GPIO_ACTIVE_HIGH>; + disable-wp; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins_a>; + cs-gpios = <&gpioz 3 0>; + /* Use PIO for the display */ + /delete-property/dmas; + /delete-property/dma-names; + status = "disabled"; /* Enable once there is display driver */ + /* + * Note: PF3/GPIO_A , PD6/GPIO_B , PG0/GPIO_C , PC6/GPIO_E are + * also connected to the display board connector. + */ +}; + +&usart3 { + pinctrl-names = "default"; + pinctrl-0 = <&usart3_pins_a>; + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; +}; + +/* + * Note: PI3 is UART1_RTS and PI5 is UART1_CTS on DRC02 (uart4 of STM32MP1), + * however the STM32MP1 pinmux cannot map them to UART4 . + */ + +&uart8 { /* RS485 */ + linux,rs485-enabled-at-boot-time; + pinctrl-names = "default"; + pinctrl-0 = <&uart8_pins_a>; + rts-gpios = <&gpioe 6 GPIO_ACTIVE_HIGH>; + /delete-property/dmas; + /delete-property/dma-names; + status = "okay"; +}; + +&usbh_ehci { + phys = <&usbphyc_port0>; + status = "okay"; +}; + +&usbphyc { + status = "okay"; +}; + +&usbphyc_port0 { + phy-supply = <&vdd_usb>; +}; + +&usbphyc_port1 { + phy-supply = <&vdd_usb>; +}; |